 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| S1D13A04 LCD/USB Companion Chip .D at Sh a et e 4U . om c w w w S1D13A04 TECHNICAL MANUAL Document Number: X37A-Q-001-01 w w w .D t a S a e h t e U 4 .c m o Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All other trademarks are the property of their respective owners. w w w .D at Sh a et e 4U . om c Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-Q-001-01 TECHNICAL MANUAL Issue Date: 01/10/02 Epson Research and Development Vancouver Design Center Page 3 COMPREHENSIVE SUPPORT TOOLS EPSON provides the designer and manufacturer a complete set of resources and tools for the development of LCD Graphics Systems. Documentation * Technical manuals * Evaluation/Demonstration board manual Evaluation/Demonstration Board * * * * * * * Assembled and fully tested Graphics Evaluation/Demonstration board Schematic of Evaluation/Demonstration board Parts List Installation Guide CPU Independent Software Utilities Evaluation Software Display Drivers Application Engineering Support EPSON offers the following services through their Sales and Marketing Network: * Sales Technical Support * Customer Training * Design Assistance Application Engineering Support Engineering and Sales Support is provided by: Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk/ Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de TECHNICAL MANUAL Issue Date: 01/10/02 S1D13A04 X37A-Q-001-01 Page 4 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-Q-001-01 TECHNICAL MANUAL Issue Date: 01/10/02 ENERGY S AV I N G EPSON GRAPHICS S1D13A04 September 2001 S1D13A04 LCD/USB Companion Chip The S1D13A04 is an LCD/USB solution designed for seamless connection to a wide variety of microprocessors. The S1D13A04 integrates a USB slave controller and an LCD graphics controller with an embedded 160K byte SRAM display buffer. The LCD controller, based on the popular S1D13706, supports all standard panel types including the Sharp HR-TFT family of products. In addition to the S1D13706 feature set, the S1D13A04 includes a Hardware Acceleration Engine to greatly improve screen drawing functions. The USB controller provides revision 1.1 compliance for applications requiring a USB client.This high level of integration provides a low cost, low power, single chip solution to meet the demands of embedded markets requiring USB client support, such as Mobile Communications devices and Palm-size PCs. The S1D13A04 utilizes a guaranteed low-latency CPU architecture that provides support for microprocessors without READY/WAIT# handshaking signals. The 32-bit internal data path, write buffer and the Hardware Acceleration Engine provide high performance bandwidth into display memory allowing for fast display updates. `Direct' support for the Sharp HR-TFT removes the requirement of an external Timing Control IC. Additionally, products requiring a rotated display can take advantage of the SwivelViewTM feature which provides hardware rotation of the display memory transparent to the software application. The S1D13A04 also provides support for "Picture-in-Picture Plus" (a variable size Overlay window). The S1D13A04, with its integrated USB client, provides impressive support for Palm OS handhelds. However, its impartiality to CPU type or operating system makes it an ideal display solution for a wide variety of applications. FEATURES * * * * * * * * Embedded 160KB Display Buffer. Low Operating Voltage. Low-latency CPU interface. Direct support for multiple CPU types. Programmable resolutions and color depths. Passive LCD support. Active Matrix LCD support. `Direct' Sharp HR-TFT support. * USB Client, Revision 1.1 compliant. * SwivelViewTM (90, 180, 270 hardware * * * * * * rotation of displayed image). "Picture-in-Picture Plus". Pixel Doubling. Hardware Acceleration Engine. Software Initiated Power Save Mode. Software Video Invert. 121-pin PFBGA or TQFP15 128-pin package. SYSTEM BLOCK DIAGRAM USB CPU Data and Control Signals S1D13A04 LCD Panel X37A-C-001-04 1 GRAPHICS S1D13A04 DESCRIPTION CPU Interface * * `Fixed' low-latency CPU access times. Direct support for: Hitachi SH-4 / SH-3. Motorola M68xxx (REDCAP2, DragonBall, ColdFire). MPU bus interface with programmable READY. Integrated LCD Controller Features * * * * 1/2/4/8/16 bit-per-pixel (bpp) support. Up to 64 gray shades on monochrome passive panels. Up to 64K colors on passive/active matrix panels. Single-panel, single-drive passive displays. * 4/8-bit monochrome LCD interface. * 4/8/16-bit color passive LCD interface. 9/12/18-bit Active matrix TFT interface. 18-bit `Direct' HR-TFT interface. SwivelView: hardware rotation by 90, 180, 270. "Picture-in-Picture Plus": displays a variable size window overlaid over background image. Pixel Doubling: horizontal and vertical resolutions can be doubled without any additional memory. Software video invert. Typical resolutions supported: 320x240@16 bpp 320x320@8 bpp 160x160@16 bpp (2 pages) 160x240@16 bpp 2D BitBLT Engine. Write BLT Transparent Write BLT Move BLT Transparent Move BLT Solid Fill BLT Read BLT Pattern Fill Color Expansion BLT Move BLT with Color Expansion Memory Interface * * * * * * * * * Embedded 160K byte SRAM display buffer. Software Initiated Power Save Mode. COREVDD 2.0 10% or 2.5 10% volts. IOVDD 3.0 10% volts. Three independent clock inputs including dedicated USB clock (single clock possible if USB not required). Flexible clock source selection and divides. 121-pin PFBGA. 128-pin TQFP15. USB Client, Revision 1.1 Compliant. Power Down Modes Operating Voltage * * * * * * * Clock Source Package * Integrated USB Features CONTACT YOUR SALES REPRESENTATIVE FOR THESE COMPREHENSIVE DESIGN TOOLS * S1D13A04 Technical * Palm OS Hardware Manual Abstraction Layer * S5U13A04 Evaluation Boards * Windows CE Display Driver * CPU Independent Software * VXWorks TornadoTM Display Driver Utilities Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk/ North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Copyright (c) 2000, 2001 Epson Research and Development, Inc. All rights reserved. VDC Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/ EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. Palm Computing is a registered trademark and the Palm OS platform Platinum logo is a trademark of Palm Computing, Inc., 3Com or its subsidiaries. Microsoft, Windows, and the Windows CE Logo are registered trademarks of Microsoft Corporation. All other trademarks are the property of their respective owners. 2 X37A-C-001-04 S1D13A04 LCD/USB Companion Chip Hardware Functional Specification Document Number: X37A-A-001-06 Status: Revision 6.0 Issue Date: 2003/05/01 Copyright (c) 2001, 2003 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All other Trademarks are the property of their respective owners Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 3 Table of Contents 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.1 Scope . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1.2 Overview Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Features . . . . . . . . . . 2.1 Integrated Frame Buffer 2.2 CPU Interface . . . . 2.3 Display Support . . . . 2.4 Display Modes . . . . 2.5 Display Features . . . 2.6 Clock Source . . . . . 2.7 USB Device . . . . . 2.8 2D Acceleration . . . 2.9 Miscellaneous . . . . . . . . . . . . . . .. . . . . . . . . . .. .. .. .. .. .. .. .. .. .. . . . . . . . . . . . . . . . . . . . . .. . . . . . . . . . .. .. .. .. .. .. .. .. .. .. . . . . . . . . . . . . . . . . . . . . ... .. .. .. .. .. .. .. .. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... .. .. .. .. .. .. .. .. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... .. .. .. .. .. .. .. .. .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 12 12 12 12 13 13 13 13 14 2 3 Typical System Implementation Diagrams . . . . . . . . . . . . . . . . . . . . . . 15 3.1 Typical System Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . 15 3.2 USB Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Pins . . . . . . . . . . . . . . . . . . 4.1 Pinout Diagram - PFBGA - 121-pin . 4.2 Pinout Diagram - TQFP15 - 128-pin 4.3 Pin Descriptions . . . . . . . . 4.3.1 Host Interface . . . . . . . . . 4.3.2 LCD Interface . . . . . . . . . 4.3.3 Clock Input . . . . . . . . . . 4.3.4 Miscellaneous . . . . . . . . . 4.3.5 Power And Ground . . . . . . 4.4 Summary of Configuration Options . 4.5 Host Bus Interface Pin Mapping . . 4.6 LCD Interface Pin Mapping . . . . ... .. .. .. ... ... ... ... ... .. .. .. .... .... .... .... ..... ..... ..... ..... ..... .... .... .... ... .. .. .. ... ... ... ... ... .. .. .. . . . . . . . . . . . . ...... ..... ..... ..... ....... ....... ....... ....... ....... ..... ..... ..... . . . . . . . . . . . . ....... ...... ...... ...... ........ ........ ........ ........ ........ ...... ...... ...... 20 20 21 22 22 26 29 29 29 30 31 32 4 5 6 D.C. Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 A.C. Characteristics . . . . . . . . . . . . . . . . . . . 6.1 Clock Timing . . . . . . . . . . . . . . . . . 6.1.1 Input Clocks . . . . . . . . . . . . . . . . . . . . . 6.1.2 Internal Clocks . . . . . . . . . . . . . . . . . . . 6.2 CPU Interface Timing . . . . . . . . . . . . . . 6.2.1 Generic #1 Interface Timing (e.g. Epson EOC33) . 6.2.2 Generic #2 Interface Timing (e.g. ISA) . . . . . . . . . . . . . . ...... ..... ....... ....... ..... ....... ....... . . . . . . . ... .. ... ... .. ... ... .... .... ..... ..... .... ..... ..... 34 34 34 35 36 36 38 Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 4 Epson Research and Development Vancouver Design Center 6.2.3 Hitachi SH-3 Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 6.2.4 Hitachi SH-4 Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 6.2.5 Motorola MC68K #1 Interface Timing (e.g. MC68000) . . . . . . . . . . . . . . . 44 6.2.6 Motorola MC68K #2 Interface Timing (e.g. MC68030) . . . . . . . . . . . . . . . 46 6.2.7 Motorola REDCAP2 Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . 48 6.2.8 Motorola Dragonball Interface Timing with DTACK (e.g. MC68EZ328/MC68VZ328) 50 6.2.9 Motorola Dragonball Interface Timing w/o DTACK (e.g. MC68EZ328/MC68VZ328) 52 6.3 LCD Power Sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . .54 6.3.1 Passive/TFT Power-On Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 6.3.2 Passive/TFT Power-Off Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 6.3.3 `Direct' HR-TFT Interface Power-On/Off Sequence . . . . . . . . . . . . . . . . . 55 6.4 Display Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 6.4.1 Generic STN Panel Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 6.4.2 Single Monochrome 4-Bit Panel Timing . . . . . . . . . . . . . . . . . . . . . . . 60 6.4.3 Single Monochrome 8-Bit Panel Timing . . . . . . . . . . . . . . . . . . . . . . . 62 6.4.4 Single Color 4-Bit Panel Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 6.4.5 Single Color 8-Bit Panel Timing (Format 1) . . . . . . . . . . . . . . . . . . . . . 66 6.4.6 Single Color 8-Bit Panel Timing (Format 2) . . . . . . . . . . . . . . . . . . . . . 68 6.4.7 Single Color 16-Bit Panel Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 6.4.8 Generic TFT Panel Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 6.4.9 9/12/18-Bit TFT Panel Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 6.4.10 160x160 Sharp `Direct' HR-TFT Panel Timing (e.g. LQ031B1DDxx) . . . . . . . 76 6.4.11 320x240 Sharp `Direct' HR-TFT Panel Timing (e.g. LQ039Q2DS01) . . . . . . . . 80 6.5 USB Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 7 Clocks . . . . . . . . . . . 7.1 Clock Descriptions . . 7.1.1 BCLK . . . . . . 7.1.2 MCLK . . . . . . 7.1.3 PCLK . . . . . . 7.1.4 PWMCLK . . . . 7.1.5 USBCLK . . . . 7.2 Clock Selection . . . 7.3 Clocks versus Functions . . . . . . . . . ...... ..... ....... ....... ....... ....... ....... ..... ..... . . . . . . . . . ... .. ... ... ... ... ... .. .. ... .. .. .. ... ... .... .... ..... ..... ..... ..... ..... .... .... .... .... .... .... ..... ..... ... .. ... ... ... ... ... .. .. ... .. .. .. ... ... . . . . . . . . . . . . . . . ...... ..... ....... ....... ....... ....... ....... ..... ..... ...... ..... ..... ..... ....... ....... . . . . . . . . . . . . . . . . . . . . .84 . . . . .84 . . . . . . 84 . . . . . . 84 . . . . . . 85 . . . . . . 86 . . . . . . 86 . . . . .87 . . . . .88 . . . . . .89 . . . . .89 . . . . .89 . . . . .91 . . . . . . 91 . . . . . . 92 8 Registers . . . . . . . . . . . . . . . . . 8.1 Register Mapping . . . . . . . . . 8.2 Register Set . . . . . . . . . . . . 8.3 LCD Register Descriptions (Offset = 0h) 8.3.1 Read-Only Configuration Registers 8.3.2 Clock Configuration Registers . . S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 5 8.3.3 Panel Configuration Registers . . . . . . . . . . . . 8.3.4 Look-Up Table Registers . . . . . . . . . . . . . . 8.3.5 Display Mode Registers . . . . . . . . . . . . . . . 8.3.6 Picture-in-Picture Plus (PIP+) Registers . . . . . . 8.3.7 Miscellaneous Registers . . . . . . . . . . . . . . . 8.4 USB Registers (Offset = 4000h) . . . . . . . . . . 8.5 2D Acceleration (BitBLT) Registers (Offset = 8000h) . 8.6 2D Accelerator (BitBLT) Data Register Descriptions . . 9 . . . . . . . . ... ... ... ... ... .. .. .. . . . . . . . . ... ... ... ... ... .. .. .. . . . . . . . . ... ... ... ... ... .. .. .. . . . . . . . . ... ... ... ... ... .. .. .. . 93 . 98 . 100 . 105 . 110 . 117 . 135 . 141 2D Accelerator (BitBLT) Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 9.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 9.2 BitBLT Operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144 10 Frame Rate Calculation 11 Display Data Formats 12 Look-Up Table Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 12.1 Monochrome Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145 12.2 Color Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147 13 SwivelViewTM . . . . . . . . . . . . 13.1 Concept . . . . . . . . . . . 13.2 90 SwivelViewTM . . . . . . 13.2.1 Register Programming . . . 13.3 180 SwivelViewTM . . . . . . 13.3.1 Register Programming . . . 13.4 270 SwivelViewTM . . . . . . 13.4.1 Register Programming . . . 14 Picture-in-Picture Plus (PIP+) 14.1 Concept . . . . . . . . 14.2 With SwivelView Enabled 14.2.1 SwivelView 90 . . . 14.2.2 SwivelView 180 . . 14.2.3 SwivelView 270 . . ... ... ... .... .... .... . . . . . . . . . . . . . . ... .. .. ... .. ... .. ... ... .. .. ... ... ... .... .... .... ..... .... ..... .... ..... .... .... .... ..... ..... ..... ... .. .. ... .. ... .. ... ... .. .. ... ... ... . . . . . . . . . . . . . . ...... ..... ..... ....... ..... ....... ..... ....... ...... ..... ..... ....... ....... ....... . . . . . . . . . . . . . . ... .. .. ... .. ... .. ... . . . . 151 . . . . 151 . . . . 151 . . . . . 152 . . . . 153 . . . . . 153 . . . . 154 . . . . . 155 . . . . . . . 156 . . . . . . 156 . . . . . . 157 . . . . . . . . 157 . . . . . . . . 157 . . . . . . . . 158 15 Power Save Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159 16 Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160 17 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162 18 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163 Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 6 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 7 List of Tables Table 4-1: PFBGA 121-pin Mapping . . . . . . . . . . . . . . . . . . . . . . . Table 4-2: Host Interface Pin Descriptions . . . . . . . . . . . . . . . . . . . . Table 4-3: LCD Interface Pin Descriptions . . . . . . . . . . . . . . . . . . . . Table 4-4: Clock Input Pin Descriptions. . . . . . . . . . . . . . . . . . . . . . Table 4-5: Miscellaneous Pin Descriptions . . . . . . . . . . . . . . . . . . . . Table 4-6: Power And Ground Pin Descriptions . . . . . . . . . . . . . . . . . Table 4-7: Summary of Power-On/Reset Options . . . . . . . . . . . . . . . . . Table 4-8: Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . Table 4-9: LCD Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . Table 5-1: Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . Table 5-2: Recommended Operating Conditions . . . . . . . . . . . . . . . . . Table 5-3: Electrical Characteristics for VDD = 3.3V typical . . . . . . . . . . . Table 6-1: Clock Input Requirements for CLKI when CLKI to BCLK divide > 1 Table 6-2: Clock Input Requirements for CLKI when CLKI to BCLK divide = 1 Table 6-3: Clock Input Requirements for CLKI2 . . . . . . . . . . . . . . . . . Table 6-4: Internal Clock Requirements . . . . . . . . . . . . . . . . . . . . . . Table 6-5: Generic #1 Interface Timing . . . . . . . . . . . . . . . . . . . . . . Table 6-6: Generic #1 Interface Truth Table for Little Endian . . . . . . . . . . Table 6-7: Generic #1 Interface Truth Table for Big Endian . . . . . . . . . . . Table 6-8: Generic #2 Interface Timing . . . . . . . . . . . . . . . . . . . . . . Table 6-9: Generic #2 Interface Truth Table for Little Endian . . . . . . . . . . Table 6-10: Hitachi SH-3 Interface Timing . . . . . . . . . . . . . . . . . . . . . Table 6-11: Hitachi SH-4 Interface Timing . . . . . . . . . . . . . . . . . . . . . Table 6-12: Motorola MC68K#1 Interface Timing . . . . . . . . . . . . . . . . . Table 6-13: Motorola MC68K#2 Interface Timing . . . . . . . . . . . . . . . . . Table 6-14: Motorola Redcap2 Interface Timing . . . . . . . . . . . . . . . . . . Table 6-15: Motorola Dragonball Interface Timing with DTACK . . . . . . . . . Table 6-16: Motorola Dragonball Interface Timing w/o DTACK . . . . . . . . . Table 6-17: Passive/TFT Power-On Sequence Timing . . . . . . . . . . . . . . . Table 6-18: Passive/TFT Power-Off Sequence Timing . . . . . . . . . . . . . . . Table 6-19: Panel Timing Parameter Definition and Register Summary . . . . . . Table 6-20: Single Monochrome 4-Bit Panel A.C. Timing . . . . . . . . . . . . . Table 6-21: Single Monochrome 8-Bit Panel A.C. Timing . . . . . . . . . . . . . Table 6-22: Single Color 4-Bit Panel A.C. Timing . . . . . . . . . . . . . . . . . Table 6-23: Single Color 8-Bit Panel A.C. Timing (Format 1) . . . . . . . . . . . Table 6-24: Single Color 8-Bit Panel A.C. Timing (Format 2) . . . . . . . . . . . Table 6-25: Single Color 16-Bit Panel A.C. Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 22 26 29 29 29 30 31 32 33 33 33 34 35 35 35 37 37 37 39 39 41 43 45 47 49 51 53 54 55 57 61 63 65 67 69 71 Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 8 Epson Research and Development Vancouver Design Center Table 6-26: TFT A.C. Timing . . . . . . . . . . . . . . . . . . . . . . Table 6-27: 160x160 Sharp `Direct' HR-TFT Horizontal Timing . . . Table 6-28: 160x160 Sharp `Direct' HR-TFT Panel Vertical Timing . Table 6-29: 320x240 Sharp `Direct' HR-TFT Panel Horizontal Timing Table 6-30: 320x240 Sharp `Direct' HR-TFT Panel Vertical Timing . Table 6-31 USB Interface Timing . . . . . . . . . . . . . . . . . . . Table 7-1: BCLK Clock Selection . . . . . . . . . . . . . . . . . . . Table 7-2: MCLK Clock Selection. . . . . . . . . . . . . . . . . . . Table 7-3: PCLK Clock Selection . . . . . . . . . . . . . . . . . . . Table 7-4: Relationship between MCLK and PCLK. . . . . . . . . . Table 7-5: PWMCLK Clock Selection. . . . . . . . . . . . . . . . . Table 7-6: S1D13A04 Internal Clock Requirements. . . . . . . . . . Table 8-1: S1D13A04 Register Mapping . . . . . . . . . . . . . . . Table 8-2: S1D13A04 Register Set . . . . . . . . . . . . . . . . . . Table 8-3: MCLK Divide Selection . . . . . . . . . . . . . . . . . . Table 8-4: PCLK Divide Selection. . . . . . . . . . . . . . . . . . . Table 8-5: PCLK Source Selection. . . . . . . . . . . . . . . . . . . Table 8-6: Panel Data Width Selection . . . . . . . . . . . . . . . . Table 8-7: Active Panel Resolution Selection . . . . . . . . . . . . . Table 8-8: LCD Panel Type Selection . . . . . . . . . . . . . . . . . Table 8-9: SwivelViewTM Mode Select Options . . . . . . . . . . . Table 8-10: LCD Bit-per-pixel Selection . . . . . . . . . . . . . . . . Table 8-11: 32-bit Address Increments for Color Depth . . . . . . . . Table 8-12: 32-bit Address Increments for Color Depth . . . . . . . . Table 8-13: 32-bit Address Increments for Color Depth . . . . . . . . Table 8-14: 32-bit Address Increments for Color Depth . . . . . . . . Table 8-15: PWM Clock Divide Select Options . . . . . . . . . . . . Table 8-16: PWMCLK Source Selection . . . . . . . . . . . . . . . . Table 8-17: PWMOUT Duty Cycle Select Options . . . . . . . . . . . Table 8-18: BitBLT FIFO Words Available . . . . . . . . . . . . . . Table 8-19 :BitBLT ROP Code/Color Expansion Function Selection . Table 8-20 :BitBLT Operation Selection . . . . . . . . . . . . . . . . Table 8-21 :BitBLT Source Start Address Selection . . . . . . . . . . Table 15-1: Power Save Mode Function Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 . 77 . 79 . 81 . 81 . 83 . 84 . 84 . 85 . 86 . 86 . 88 . 89 . 89 . 92 . 92 . 93 . 93 . 94 . 94 . 95 . 96 .106 .107 .108 .109 .114 .115 .115 .136 .137 .138 .139 .159 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 9 List of Figures Figure 3-1: Figure 3-2: Figure 3-3: Figure 3-4: Figure 3-5: Figure 3-6: Figure 3-7: Figure 3-8: Figure 3-9: Figure 4-1: Figure 4-2: Figure 6-1: Figure 6-2: Figure 6-3: Figure 6-4: Figure 6-5: Figure 6-6: Figure 6-7: Figure 6-8: Figure 6-9: Figure 6-10: Figure 6-11: Figure 6-12: Figure 6-13: Figure 6-14: Figure 6-15: Figure 6-16: Figure 6-17: Figure 6-18: Figure 6-19: Figure 6-20: Figure 6-21: Figure 6-22: Figure 6-23: Figure 6-24: Figure 6-25: Figure 6-26: Typical System Diagram (Generic #1 Bus) . . . . . . . . . . . . . . . . . . . . . . Typical System Diagram (Generic #2 Bus) . . . . . . . . . . . . . . . . . . . . . . Typical System Diagram (Hitachi SH-4 Bus) . . . . . . . . . . . . . . . . . . . . . Typical System Diagram (Hitachi SH-3 Bus) . . . . . . . . . . . . . . . . . . . . . Typical System Diagram (MC68K # 1, Motorola 16-Bit 68000) . . . . . . . . . . . Typical System Diagram (MC68K #2, Motorola 32-Bit 68030) . . . . . . . . . . . . Typical System Diagram (Motorola REDCAP2 Bus) . . . . . . . . . . . . . . . . . Typical System Diagram (Motorola MC68EZ328/MC68VZ328 "DragonBall" Bus) . USB Typical Implementation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pinout Diagram - PFBGA 121-pin . . . . . . . . . . . . . . . . . . . . . . . . . . . Pinout Diagram - TQFP15 128-pin . . . . . . . . . . . . . . . . . . . . . . . . . . . Clock Input Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Generic #1 Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Generic #2 Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hitachi SH-3 Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hitachi SH-4 Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Motorola MC68K #1 Interface Timing. . . . . . . . . . . . . . . . . . . . . . . . . Motorola MC68K #2 Interface Timing. . . . . . . . . . . . . . . . . . . . . . . . . Motorola Redcap2 Interface Timing . . . . . . . . . . . . . . . . . . . . . . . . . . Motorola Dragonball Interface Timing with DTACK . . . . . . . . . . . . . . . . . Motorola Dragonball Interface Timing w/o DTACK . . . . . . . . . . . . . . . . . Passive/TFT Power-On Sequence Timing . . . . . . . . . . . . . . . . . . . . . . . Passive/TFT Power-Off Sequence Timing . . . . . . . . . . . . . . . . . . . . . . . Panel Timing Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Generic STN Panel Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single Monochrome 4-Bit Panel Timing . . . . . . . . . . . . . . . . . . . . . . . . Single Monochrome 4-Bit Panel A.C. Timing . . . . . . . . . . . . . . . . . . . . . Single Monochrome 8-Bit Panel Timing . . . . . . . . . . . . . . . . . . . . . . . . Single Monochrome 8-Bit Panel A.C. Timing . . . . . . . . . . . . . . . . . . . . . Single Color 4-Bit Panel Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . Single Color 4-Bit Panel A.C. Timing . . . . . . . . . . . . . . . . . . . . . . . . . Single Color 8-Bit Panel Timing (Format 1) . . . . . . . . . . . . . . . . . . . . . . Single Color 8-Bit Panel A.C. Timing (Format 1) . . . . . . . . . . . . . . . . . . . Single Color 8-Bit Panel Timing (Format 2) . . . . . . . . . . . . . . . . . . . . . . Single Color 8-Bit Panel A.C. Timing (Format 2) . . . . . . . . . . . . . . . . . . . Single Color 16-Bit Panel Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . Single Color 16-Bit Panel A.C. Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 . 15 . 16 . 16 . 17 . 17 . 18 . 18 . 19 . 20 . 21 . 34 . 36 . 38 . 40 . 42 . 44 . 46 . 48 . 50 . 52 . 54 . 55 . 56 . 58 . 60 . 61 . 62 . 63 . 64 . 65 . 66 . 67 . 68 . 69 . 70 . 71 Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 10 Epson Research and Development Vancouver Design Center Figure 6-27: Figure 6-28: Figure 6-29: Figure 6-30: Figure 6-31: Figure 6-32: Figure 6-33: Figure 6-34 Figure 6-35 Figure 6-36 Figure 6-37 Figure 7-1: Figure 8-1: Figure 8-2: Figure 11-1: Figure 12-1: Figure 12-2: Figure 12-3: Figure 12-4: Figure 12-5: Figure 12-6: Figure 12-7: Figure 12-8: Figure 13-1: Figure 13-2: Figure 13-3: Figure 14-1: Figure 14-2: Figure 14-3: Figure 14-4: Figure 16-1: Figure 16-2: Generic TFT Panel Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 18-Bit TFT Panel Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 TFT A.C. Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 160x160 Sharp `Direct' HR-TFT Panel Horizontal Timing . . . . . . . . . . . . . . . .76 160x160 Sharp `Direct' HR-TFT Panel Vertical Timing. . . . . . . . . . . . . . . . . .78 320x240 Sharp `Direct' HR-TFT Panel Horizontal Timing . . . . . . . . . . . . . . . .80 320x240 Sharp `Direct' HR-TFT Panel Vertical Timing. . . . . . . . . . . . . . . . . .81 Data Signal Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 Differential Data Jitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 Differential to EOP Transition Skew and EOP Width . . . . . . . . . . . . . . . . . . .82 Receiver Jitter Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .83 Clock Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87 Display Data Byte/Word Swap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 PWM Clock Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 4/8/16 Bit-Per-Pixel Display Data Memory Organization . . . . . . . . . . . . . . . . 144 1 Bit-per-pixel Monochrome Mode Data Output Path . . . . . . . . . . . . . . . . . . 145 2 Bit-per-pixel Monochrome Mode Data Output Path . . . . . . . . . . . . . . . . . . 145 4 Bit-per-pixel Monochrome Mode Data Output Path . . . . . . . . . . . . . . . . . . 146 8 Bit-per-pixel Monochrome Mode Data Output Path . . . . . . . . . . . . . . . . . . 146 1 Bit-Per-Pixel Color Mode Data Output Path . . . . . . . . . . . . . . . . . . . . . . 147 2 Bit-Per-Pixel Color Mode Data Output Path . . . . . . . . . . . . . . . . . . . . . . 148 4 Bit-Per-Pixel Color Mode Data Output Path . . . . . . . . . . . . . . . . . . . . . . 149 8 Bit-per-pixel Color Mode Data Output Path . . . . . . . . . . . . . . . . . . . . . . 150 Relationship Between The Screen Image and the Image Refreshed in 90 SwivelView. 152 Relationship Between The Screen Image and the Image Refreshed in 180 SwivelView.153 Relationship Between The Screen Image and the Image Refreshed in 270 SwivelView.154 Picture-in-Picture Plus with SwivelView disabled . . . . . . . . . . . . . . . . . . . . 156 Picture-in-Picture Plus with SwivelView 90 enabled . . . . . . . . . . . . . . . . . . 157 Picture-in-Picture Plus with SwivelView 180 enabled . . . . . . . . . . . . . . . . . 157 Picture-in-Picture Plus with SwivelView 270 enabled . . . . . . . . . . . . . . . . . 158 Mechanical Data PFBGA 121-pin Package . . . . . . . . . . . . . . . . . . . . . . . 160 Mechanical Data TQFP15 128-pin Package . . . . . . . . . . . . . . . . . . . . . . . 161 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 11 1 Introduction 1.1 Scope This is the Hardware Functional Specification for the S1D13A04 LCD/USB Companion Chip. Included in this document are timing diagrams, AC and DC characteristics, register descriptions, and power management descriptions. This document is intended for two audiences: Video Subsystem Designers and Software Developers. This document is updated as appropriate. Please check for the latest revision of this document before beginning any development. The latest revision can be downloaded at www.erd.epson.com We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. 1.2 Overview Description The S1D13A04 is an LCD/USB solution designed for seamless connection to a wide variety of microprocessors. The S1D13A04 integrates a USB slave controller and an LCD graphics controller with an embedded 160K byte SRAM display buffer. The LCD controller, based on the popular S1D13706, supports all standard panel types including the Sharp HR-TFT family of products. In addition to the S1D13706 feature set, the S1D13A04 includes a Hardware Acceleration Engine to greatly improve screen drawing functions. The USB controller provides revision 1.1 compliance for applications requiring a USB client.This high level of integration provides a low cost, low power, single chip solution to meet the demands of embedded markets requiring USB client support, such as Mobile Communications devices and Palm-size PCs. The S1D13A04 utilizes a guaranteed low-latency CPU architecture that provides support for microprocessors without READY/WAIT# handshaking signals. The 32-bit internal data path, write buffer and the Hardware Acceleration Engine provide high performance bandwidth into display memory allowing for fast display updates. `Direct' support for the Sharp HR-TFT removes the requirement of an external Timing Control IC. Additionally, products requiring a rotated display can take advantage of the SwivelViewTM feature which provides hardware rotation of the display memory transparent to the software application. The S1D13A04 also provides support for "Picture-in-Picture Plus" (a variable size Overlay window). The S1D13A04, with its integrated USB client, provides impressive support for Palm OS handhelds. However, its impartiality to CPU type or operating system makes it an ideal display solution for a wide variety of applications. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 12 Epson Research and Development Vancouver Design Center 2 Features 2.1 Integrated Frame Buffer * Embedded 160k byte SRAM display buffer. 2.2 CPU Interface * Direct support of the following interfaces: Generic MPU bus interface with programmable ready (WAIT#). Hitachi SH-4 / SH-3. Motorola M68K. Motorola MC68EZ328/MC68VZ328 DragonBall. Motorola "REDCAP2" - no WAIT# signal. * "Fixed" low-latency CPU access times. * Registers are memory-mapped - M/R# input selects between memory and register address space. * The complete 160k byte display buffer is directly and contiguously available through the 18-bit address bus. 2.3 Display Support * Single-panel, single drive passive displays. * 4/8-bit monochrome LCD interface. * 4/8/16-bit color LCD interface. * Active Matrix TFT interface. * 9/12/18-bit interface. * `Direct' support for 18-bit Sharp HR-TFT LCD or compatible interface. 2.4 Display Modes * 1/2/4/8/16 bit-per-pixel (bpp) color depths. * Up to 64 gray shades on monochrome passive LCD panels. * Up to 64K colors on passive panels. * Up to 64K colors on active matrix LCD panels. * Example resolutions: 320x240 at a color depth of 16 bpp 320x320 at a color depth of 8 bpp 160x160 at a color depth of 16 bpp (2 pages) 160x240 at a color depth of 16 bpp S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 13 2.5 Display Features * SwivelViewTM: 90, 180, 270 counter-clockwise hardware rotation of display image. * Virtual display support: displays images larger than the panel size through the use of panning and scrolling. * Picture-in-Picture Plus (PIP+): displays a variable size window overlaid over background image. * Pixel Doubling: independent control of both horizontal and vertical pixel doubling. * example usage: 160x160 8 bpp can be expanded to 320x320 8 bpp without any additional memory. * Double Buffering/Multi-pages: provides smooth animation and instantaneous screen updates. 2.6 Clock Source * Three independent clock inputs: CLKI, CLKI2 and USBCLK. * Flexible clock source selection: * internal Bus Clock (BCLK) selected from CLKI or CLKI/2 (CNF6) * internal Memory Clock (MCLK) selected from BCLK or BCLK divide ratio (REG[04h) * internal Pixel Clock (PCLK) selected from CLKI, CLKI2, MCLK, or BCLK. PCLK can also be divided down from source (REG[08h]) * Single clock input possible if USB support not required. 2.7 USB Device * USB Client, revision 1.1 compliant. * Dedicated clock input: USBCLK. 2.8 2D Acceleration * 2D BitBLT engine including: Write BitBLT Move BitBLT Solid Fill BitBLT Pattern Fill BitBLT Move BitBLT with Color Expansion Transparent Write BitBLT Transparent Move BitBLT Read BitBLT Color Expansion BitBLT Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 14 Epson Research and Development Vancouver Design Center 2.9 Miscellaneous * Software Video Invert. * Software initiated Power Save mode. * General Purpose Input/Output pins are available. * IO Operates at 3.3 volts 10%. * Core operates at 2.0 volts 10% or 2.5 volts 10%. * 121-pin PFBGA package. * 128-pin TQFP15 package. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 15 3 Typical System Implementation Diagrams 3.1 Typical System Diagrams. Oscillator Generic #1 BUS IOVDD BS# AB0 VSS CLKI2 FPDAT[15:0] A[27:18] CSn# A[17:1] D[15:0] WE0# WE1# RD0# RD1# WAIT# BUSCLK RESET# Decoder M/R# CS# AB[17:1] DB[15:0] WE0# WE1# RD# RD/WR# WAIT# CLKI RESET# FPFRAME FPLINE FPSHIFT DRDY 16-bit Single FPFRAME LCD Display D[15:0] FPLINE FPSHIFT MOD Bias Power S1D13A04 GPIO0 Figure 3-1: Typical System Diagram (Generic #1 Bus) . Oscillator Generic #2 BUS BS# RD/WR# A[27:18] CSn# A[17:0] D[15:0] WE# BHE# RD# Decoder M/R# CS# AB[17:0] DB[15:0] WE0# WE1# RD# CLKI2 IOVDD FPDAT[8:0] FPFRAME D[8:0] FPFRAME 9-bit TFT Display Bias Power FPLINE FPSHIFT FPLINE FPSHIFT DRDY S1D13A04 DRDY GPIO0 WAIT# WAIT# BUSCLK RESET# CLKI RESET# Figure 3-2: Typical System Diagram (Generic #2 Bus) Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 16 Epson Research and Development Vancouver Design Center . Oscillator SH-4 BUS AB0 A[25:18] CSn# A[17:1] D[15:0] WE0# WE1# BS# RD/WR# RD# Decoder VSS M/R# CS# AB[17:1] DB[15:0] WE0# WE1# BS# RD/WR# RD# CLKI2 FPDAT15 FPDAT12 FPDAT[9:0] FPFRAME FPLINE FPSHIFT DRDY D11 D10 D[9:0] FPFRAME Bias Power FPLINE FPSHIFT DRDY 12-bit TFT Display S1D13A04 GPIO0 RDY# WAIT# CKIO RESET# CLKI RESET# Figure 3-3: Typical System Diagram (Hitachi SH-4 Bus) . Oscillator SH-3 BUS CLKI2 AB0 A[25:18] CSn# A[17:1] D[15:0] WE0# WE1# BS# RD/WR# RD# Decoder VSS M/R# CS# AB[17:1] DB[15:0] WE0# WE1# BS# RD/WR# RD# FPSHIFT DRDY FPSHIFT DRDY Bias Power FPLINE FPLINE FPDAT[17:0] FPFRAME D[17:0] FPFRAME 18-bit TFT Display S1D13A04 GPIO0 WAIT# WAIT# CKIO RESET# CLKI RESET# Figure 3-4: Typical System Diagram (Hitachi SH-3 Bus) S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 17 . Oscillator MC68K #1 BUS RD# WE0# A[23:18] FC0, FC1 Decoder M/R# CLKI2 IOVDD FPDAT[17:0] FPFRAME FPLINE FPSHIFT D[17:0] SPS LP CLK PS CLS REV SPL 18-bit HR-TFT Display Decoder A[17:1] D[15:0] LDS# UDS# AS# R/W# DTACK# CS# AB[17:1] DB[15:0] AB0 WE1# BS# RD/WR# WAIT# GPIO0 GPIO1 GPIO2 GPIO3 S1D13A04 CLK RESET# CLKI RESET# Figure 3-5: Typical System Diagram (MC68K # 1, Motorola 16-Bit 68000) . Oscillator MC68K #2 BUS A[31:18] FC0, FC1 Decoder M/R# CLKI2 FPDAT[17:0] Decoder A[17:0] D[31:16] CS# AB[17:0] DB[15:0] FPFRAME FPLINE FPSHIFT GPIO0 DS# AS# R/W# SIZ1 SIZ0 DSACK1# WE1# BS# RD/WR# RD# WE0# WAIT# GPIO1 GPIO2 D[17:0] SPS LP CLK PS CLS REV SPL 18-bit HR-TFT Display S1D13A04 GPIO3 CLK RESET# CLKI RESET# Figure 3-6: Typical System Diagram (MC68K #2, Motorola 32-Bit 68030) Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 18 Epson Research and Development Vancouver Design Center . Oscillator CLKI2 REDCAP2 BUS IOVDD BS# FPDAT[7:4] A[21:18] CSn A[17:1] D[15:0] Decoder M/R# CS# AB[17:1] DB[15:0] FPFRAME FPLINE DRDY FPSHIFT D[3:0] FPSHIFT 4-bit Single LCD Display Bias Power FPFRAME FPLINE MOD R/W OE EB1 EB0 CLK RESET_OUT RD/WR# RD# WE0# WE1# CLKI RESET# AB0 VSS S1D13A04 GPIO0 *Note: CSn# can be any of CS0-CS4 Figure 3-7: Typical System Diagram (Motorola REDCAP2 Bus) . Oscillator MC68EZ328/ MC68VZ328 DragonBall BUS A[25:18] BS# RD/WR# Decoder M/R# CLKI2 IOVDD FPDAT[7:0] FPSHIFT D[7:0] FPSHIFT 8-bit Single LCD Display Bias Power CSX A[17:1] D[15:0] CS# AB[17:1] DB[15:0] FPFRAME FPLINE DRDY FPFRAME FPLINE MOD S1D13A04 GPIO0 LWE UWE OE DTACK CLKO RESET WE0# WE1# RD# WAIT# CLKI RESET# AB0 VSS Figure 3-8: Typical System Diagram (Motorola MC68EZ328/MC68VZ328 "DragonBall" Bus) S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 19 3.2 USB Interface S1D13A04 USB Socket USBDETECT 300k 150k VBus USBPUP Full Speed Device LVDD 1.5k USBDP 20 DP USBDM 20 300k NNCD5.6LG Overvoltage Protection DM ESD Protection VSS GND Figure 3-9: USB Typical Implementation Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 20 Epson Research and Development Vancouver Design Center 4 Pins 4.1 Pinout Diagram - PFBGA - 121-pin L K J H G F E D C B A 1 2 3 4 5 6 7 8 9 10 11 BOTTOM VIEW Figure 4-1: Pinout Diagram - PFBGA 121-pin Table 4-1: PFBGA 121-pin Mapping L K J H G F E D C B A NC NC NC DB12 WAIT# RESET# RD# AB0 NC NC NC IOVDD VSS DB9 DB11 DB15 VSS BS# AB1 COREVDD VSS COREVDD DB7 DB8 DB6 DB10 DB14 RD/WR# M/R# AB2 AB3 AB5 AB4 DB3 DB4 DB5 DB13 IOVDD WE1# CS# AB8 AB6 NC AB7 DB0 DB1 DB2 NC VSS CLKI WE0# AB12 AB9 AB10 AB11 GPIO7 GPIO6 NC IOVDD GPIO5 NC AB13 AB17 AB16 AB14 AB15 GPIO3 GPIO2 GPIO1 GPIO4 FPDAT5 FPDAT8 TESTEN CNF3 CNF2 CNF1 CNF0 GPIO0 IRQ USBCLK NC FPDAT1 FPDAT6 FPDAT9 FPDAT13 CNF5 CNF4 NC IOVDD DRDY COREVDD VSS NC NC NC FPDAT0 FPDAT4 IOVDD FPDAT10 FPDAT14 NC NC NC FPFRAME COREVDD FPLINE FPDAT2 VSS FPDAT12 FPDAT16 CNF6 CLKI2 PWMOUT FPSHIFT FPDAT3 FPDAT7 FPDAT11 FPDAT15 FPDAT17 VSS IOVDD 1 2 3 4 5 6 7 8 9 10 11 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 21 4.2 Pinout Diagram - TQFP15 - 128-pin 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 VSS NC NC NC FPDAT17 FPDAT16 FPDAT15 FPDAT14 FPDAT13 FPDAT12 FPDAT11 FPDAT10 FPDAT9 FPDAT8 NC IOVDD VSS NC FPDAT6 FPDAT5 FPDAT4 FPDAT3 FPDAT2 FPDAT1 FPDAT0 FPSHIFT FPLINE FPFRAME FPDAT7 NC NC COREVDD 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 IOVDD NC CLKI2 PWMOUT NC CNF6 CNF5 CNF4 CNF3 CNF2 CNF1 CNF0 TESTEN NC AB17 AB16 AB15 AB14 AB13 AB12 NC AB11 AB10 AB9 AB8 AB7 AB6 AB5 AB4 NC VSS COREVDD COREVDD 1 COREVDD NC VSS IOVDD DRDY USBCLK IRQ GPIO0 GPIO1 GPIO2 GPIO3 NC NC GPIO4 GPIO5 GPIO6 GPIO7 NC IOVDD VSS NC DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8 NC IOVDD 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 S1D13A04 RD/WR# RESET# IOVDD WAIT# WE1# WE0# DB15 DB12 DB11 DB10 DB13 DB14 M/R# CS# CLKI VSS VSS RD# DB9 BS# AB3 4 AB2 AB1 AB0 NC NC NC NC Hardware Functional Specification Issue Date: 2003/05/01 NC 2 NC 3 NC 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Figure 4-2: Pinout Diagram - TQFP15 128-pin S1D13A04 X37A-A-001-06 Revision 6.0 Page 22 Epson Research and Development Vancouver Design Center 4.3 Pin Descriptions Key: I O IO P CI LI LB2A LB3P LO3 LB3M T1 Hi-Z CUS = = = = = = = = = = = = = Input Output Bi-Directional (Input/Output) Power pin CMOS input LVTTL input LVTTL IO buffer (6mA/-6mA@3.3V) Low noise LVTTL IO buffer (6mA/-6mA@3.3V) Low noise LVTTL Output buffer (3mA/-3mA@3.3V) Low noise LVTTL IO buffer with input mask (3mA/-3mA@3.3V) Test mode control input with pull-down resistor (typical value of 50K at 3.3V) High Impedance Custom Cell Type a LVTTL is Low Voltage TTL (see Section 5, "D.C. Characteristics" on page 33). 4.3.1 Host Interface Table 4-2: Host Interface Pin Descriptions Pin Name Type PFBGA Pin # TQFP15 Pin# Cell RESET# State Description This input pin has multiple functions. * For Generic #1, this pin is not used and should be connected to VSS. * For Generic #2, this pin inputs system address bit 0 (A0). * For SH-3/SH-4, this pin is not used and should be connected to VSS. * For MC68K #1, this pin inputs the lower data strobe (LDS#). * For MC68K #2, this pin inputs system address bit 0 (A0). * For REDCAP2, this pin is not used and should be connected to VSS. * For DragonBall, this pin is not used and should be connected to VSS. See Table 4-8: "Host Bus Interface Pin Mapping," on page 31 for summary. C6,A6,B6, E6,D5,A5, 4-6, B5,C5,D4 111-116, ,A4,C4,B3 118-125 ,A3,C3,D 3,D2,D6 AB0 I D1 7 LI -- AB[17:1] I CI -- System address bus bits 17-1. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 23 Table 4-2: Host Interface Pin Descriptions Pin Name Type PFBGA Pin # TQFP15 Pin# Cell RESET# State * * * * * Description Input data from the system data bus. For Generic #1, these pins are connected to D[15:0]. For Generic #2, these pins are connected to D[15:0]. For SH-3/SH-4, these pins are connected to D[15:0]. For MC68K #1, these pins are connected to D[15:0]. For MC68K #2, these pins are connected to D[31:16] for a 32-bit device (e.g. MC68030) or D[15:0] for a 16-bit device (e.g. MC68340). * For REDCAP2, these pins are connected to D[15:0]. * For DragonBall, these pins are connected to D[15:0]. See Table 4-8: "Host Bus Interface Pin Mapping," on page 31 for summary. This input pin has multiple functions. * For Generic #1, this pin inputs the write enable signal for the lower data byte (WE0#). * For Generic #2, this pin inputs the write enable signal (WE#) * For SH-3/SH-4, this pin inputs the write enable signal for data byte 0 (WE0#). * For MC68K #1, this pin must be tied to IO VDD * For MC68K #2, this pin inputs the bus size bit 0 (SIZ0). * For REDCAP2, this pin inputs the byte enable signal for the D[7:0] data byte (EB1). * For DragonBall, this pin inputs the byte enable signal for the D[7:0] data byte (LWE). See Table 4-8: "Host Bus Interface Pin Mapping," on page 31 for summary. This input pin has multiple functions. * For Generic #1, this pin inputs the write enable signal for the upper data byte (WE1#). * For Generic #2, this pin inputs the byte enable signal for the high data byte (BHE#). * For SH-3/SH-4, this pin inputs the write enable signal for data byte 1 (WE1#). * For MC68K #1, this pin inputs the upper data strobe (UDS#). * For MC68K #2, this pin inputs the data strobe (DS#). * For REDCAP2, this pin inputs the byte enable signal for the D[15:8] data byte (EB0). * For DragonBall, this pin inputs the byte enable signal for the D[15:8] data byte (UWE). See Table 4-8: "Host Bus Interface Pin Mapping," on page 31 for summary. CS# I E4 9 CI -- Chip select input. See Table 4-8: "Host Bus Interface Pin Mapping," on page 31 for summary. DB[15:0] IO L5,K5,J5, L4,K4,J4, J3,L3,K3, J2,H3,H2, H1,H4,G3 ,G2 23-29, 35-43 LB2A Hi-Z WE0# I E5 13 LI -- WE1# I F4 14 LI -- Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 24 Epson Research and Development Vancouver Design Center Table 4-2: Host Interface Pin Descriptions Pin Name Type PFBGA Pin # TQFP15 Pin# Cell RESET# State Description This input pin is used to select between the display buffer and register address spaces of the S1D13A04. M/R# is set high to access the display buffer and low to access the registers. See Table 4-8: "Host Bus Interface Pin Mapping," on page 31 for summary. This input pin has multiple functions. * * * * * * * For Generic #1, this pin must be tied to IO VDD. For Generic #2, this pin must be tied to IO VDD. For SH-3/SH-4, this pin inputs the bus start signal (BS#). For MC68K #1, this pin inputs the address strobe (AS#). For MC68K #2, this pin inputs the address strobe (AS#). For REDCAP2, this pin must be tied to IO VDD. For DragonBall, this pin must be tied to IO VDD. M/R# I E3 10 LI -- BS# I E2 11 LI -- See Table 4-8: "Host Bus Interface Pin Mapping," on page 31 for summary. This input pin has multiple functions. * For Generic #1, this pin inputs the read command for the upper data byte (RD1#). * For Generic #2, this pin must be tied to IO VDD. * For SH-3/SH-4, this pin inputs the RD/WR# signal. The S1D13A04 needs this signal for early decode of the bus cycle. * For MC68K #1, this pin inputs the R/W# signal. * For MC68K #2, this pin inputs the R/W# signal. * For REDCAP2, this pin inputs the R/W signal. * For DragonBall, this pin must be tied to IO VDD. See Table 4-8: "Host Bus Interface Pin Mapping," on page 31 for summary. This input pin has multiple functions. * For Generic #1, this pin inputs the read command for the lower data byte (RD0#). * For Generic #2, this pin inputs the read command (RD#). * For SH-3/SH-4, this pin inputs the read signal (RD#). * For MC68K #1, this pin must be tied to IO VDD. * For MC68K #2, this pin inputs the bus size bit 1 (SIZ1). * For REDCAP2, this pin inputs the output enable (OE). * For DragonBall, this pin inputs the output enable (OE). See Table 4-8: "Host Bus Interface Pin Mapping," on page 31 for summary. RD/WR# I F3 15 LI -- RD# I E1 12 LI -- S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 25 Table 4-2: Host Interface Pin Descriptions Pin Name Type PFBGA Pin # TQFP15 Pin# Cell RESET# State Description During a data transfer, this output pin is driven active to force the system to insert wait states. It is driven inactive to indicate the completion of a data transfer. WAIT# is released to the high impedance state after the data transfer is complete. Its active polarity is configurable. See Table 4-7: "Summary of Power-On/Reset Options," on page 30. * For Generic #1, this pin outputs the wait signal (WAIT#). * For Generic #2, this pin outputs the wait signal (WAIT#). * For SH-3 mode, this pin outputs the wait request signal (WAIT#). * For SH-4 mode, this pin outputs the device ready signal (RDY#). * For MC68K #1, this pin outputs the data transfer acknowledge signal (DTACK#). * For MC68K #2, this pin outputs the data transfer and size acknowledge bit 1 (DSACK1#). * For REDCAP2, this pin is unused (Hi-Z). * For DragonBall, this pin outputs the data transfer acknowledge signal (DTACK). See Table 4-8: "Host Bus Interface Pin Mapping," on page 31 for summary. Note: This pin should be tied to the inactive voltage level as selected by CNF5, using a pull-up or pull-down resistor. If CNF5 = 1, the WAIT# pin should be tied low using a pull-down resistor. If CNF5 = 0, the WAIT# pin should be tied high using a pull-up resistor. If WAIT# is not used, this pin should be tied either high or low using a pull-up or pull-down resistor. RESET# I F1 16 LI -- Active low input to set all internal registers to the default state and to force all signals to their inactive states. WAIT# IO G1 22 LB2A Hi-Z Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 26 Epson Research and Development Vancouver Design Center 4.3.2 LCD Interface Table 4-3: LCD Interface Pin Descriptions Pin Name Type PFBGA Pin# C10,D9,D 10,D,11,D 8,E9,E10, E11,E8,F 7,F10,F8, G7,G11,G 10,G9,G8 ,H11 TQFP15 Pin# Cell RESET# State Description FPDAT[17:0] O 71-77, 82-92 LB3P 0 Panel Data bits 17-0. This output pin has multiple functions. FPFRAME O J9 68 LB3P 0 * Frame Pulse * SPS for `Direct' HR-TFT See Table 4.6 "LCD Interface Pin Mapping," on page 32 for summary. This output pin has multiple functions. FPLINE O H9 69 LB3P 0 * Line Pulse * LP for `Direct' HR-TFT See Table 4.6 "LCD Interface Pin Mapping," on page 32 for summary. This output pin has multiple functions. FPSHIFT O H10 70 LB3P 0 * Shift Clock * CLK for `Direct' HR-TFT See Table 4.6 "LCD Interface Pin Mapping," on page 32 for summary. This output pin has multiple functions. * Display enable (DRDY) for TFT panels * 2nd shift clock (FPSHIFT2) for passive LCD with Format 1 interface * LCD backplane bias signal (MOD) for all other LCD panels * General Purpose Output See Table 4.6 "LCD Interface Pin Mapping," on page 32 for summary. This pin has multiple functions. * PS for `Direct' HR-TFT * General purpose IO pin 0 (GPIO0) GPIO0 defaults to a Hi-Z state during every RESET and defaults to an input after every RESET. When this pin is used for HR-TFT, it must be configured as an output using REG[64h]. Otherwise, it must either be configured as an output or be pulled high or low externally to avoid unnecessary current drain. See Table 4.6 "LCD Interface Pin Mapping," on page 32 for summary. DRDY O K9 60 LO3 0 GPIO0 IO L8 57 LB3M -- S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 27 Table 4-3: LCD Interface Pin Descriptions Pin Name Type PFBGA Pin# TQFP15 Pin# Cell RESET# State Description This pin has multiple functions. * CLS for `Direct' HR-TFT * General purpose IO pin 1 (GPIO1) GPIO1 defaults to a Hi-Z state during every RESET and defaults to an input after every RESET. When this pin is used for HR-TFT, it must be configured as an output using REG[64h]. Otherwise, it must either be configured as an output or be pulled high or low externally to avoid unnecessary current drain. See Table 4.6 "LCD Interface Pin Mapping," on page 32 for summary. This pin has multiple functions. * REV for `Direct' HR-TFT * General purpose IO pin 2 (GPIO2) GPIO2 defaults to a Hi-Z state during every RESET and defaults to an input after every RESET. When this pin is used for HR-TFT, it must be configured as an output using REG[64h]. Otherwise, it must either be configured as an output or be pulled high or low externally to avoid unnecessary current drain. See Table 4.6 "LCD Interface Pin Mapping," on page 32 for summary. This pin has multiple functions. * SPL for `Direct' HR-TFT * General purpose IO pin 3 (GPIO3) GPIO3 defaults to a Hi-Z state during every RESET and defaults to an input after every RESET. When this pin is used for HR-TFT, it must be configured as an output using REG[64h]. Otherwise, it must either be configured as an output or be pulled high or low externally to avoid unnecessary current drain. See Table 4.6 "LCD Interface Pin Mapping," on page 32 for summary. This pin has multiple functions. * USBPUP * General purpose IO pin 4 (GPIO4) GPIO4 IO H7 51 LB3M -- GPIO4 defaults to a Hi-Z state during every RESET and defaults to an input after every RESET. When this pin is not used for USB, it must either be configured as an output using REG[64h] or be pulled high or low externally to avoid unnecessary current drain. GPIO1 IO J7 56 LB3M -- GPIO2 IO K7 55 LB3M -- GPIO3 IO L7 54 LB3M -- Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 28 Epson Research and Development Vancouver Design Center Table 4-3: LCD Interface Pin Descriptions Pin Name Type PFBGA Pin# TQFP15 Pin# Cell RESET# State Description This pin has multiple functions. * USBDETECT * General purpose IO pin 5 (GPIO5) GPIO5 IO G6 50 LB3M -- GPIO5 defaults to a Hi-Z state during every RESET and defaults to an input after every RESET. When this pin is not used for USB, it must either be configured as an output using REG[64h] or be pulled high or low externally to avoid unnecessary current drain. This pin has multiple functions. * USBDM * General purpose IO pin 6 (GPIO6) GPIO6 IO K6 49 CUS -- GPIO6 defaults to a Hi-Z state during every RESET and defaults to an input after every RESET. When this pin is not used for USB, it must either be configured as an output using REG[64h] or be pulled high or low externally to avoid unnecessary current drain. This pin has multiple functions. * USBDP * General purpose IO pin 7 GPIO7 IO L6 48 CUS -- GPIO7 defaults to a Hi-Z state during every RESET and defaults to an input after every RESET. When this pin is not used for USB, it must either be configured as an output using REG[64h] or be pulled high or low externally to avoid unnecessary current drain. This output pin is the IRQ pin for USB. When IRQ is activated, an active high pulse is generated and stays high until the IRQ is serviced by software at REG[404Ah] or REG[404Ch]. This pin has multiple functions. PWMOUT O A9 100 LO3 0 * PWM Clock output * General purpose output IRQ O K8 58 LO3 0 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 29 4.3.3 Clock Input Table 4-4: Clock Input Pin Descriptions Pin Name CLKI CLKI2 USBCLK Type I I I PFBGA Pin# F5 B9 J8 TQFP15 Pin# 19 99 59 Cell CI CI LI RESET# State -- -- -- Description Typically used as input clock source for bus clock and memory clock Typically used as input clock source for pixel clock Typically used as input clock source for USB 4.3.4 Miscellaneous Table 4-5: Miscellaneous Pin Descriptions Pin Name Type PFBGA Pin# C9,C8,B8 ,D7,C7,B 7,A7 TQFP15 Pin# Cell RESET# State Description These inputs are used to configure the S1D13A04 - see Table 4-7: "Summary of Power-On/Reset Options," on page 30. 102-108 CI -- Note: These pins are used for configuration of the S1D13A04 and must be connected directly to IO VDD or VSS. Test Enable input used for production test only (has type 1 pull-down resistor with a typical value of 50K at 3.3V). Note: This pin must not be connected. CNF[6:0] I TESTEN I E7 109 T1 -- 4.3.5 Power And Ground Table 4-6: Power And Ground Pin Descriptions Pin Name Type PFBGA Pin# L2,G4, H6,L9, A10,F11 A2,C2, L10,J10 B2,F2, K2,G5, F9,B10,K 10 TQFP15 Pin# 20, 33, 46, 61, 80, 97 1, 64-65, 128 18, 32, 45, 62, 79, 96, 127 Cell RESET# State -- -- 6 IO VDD pins. 2 double-bonded Core VDD. pins on TQFP package. 4 Core VDD. pins on PFBGA package. 7 VSS pins. Description IOVDD COREVDD P P P P VSS P P -- Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 30 Epson Research and Development Vancouver Design Center 4.4 Summary of Configuration Options These pins are used for configuration of the S1D13A04 and must be connected directly to IOVDD or VSS. The state of CNF[6:0] are latched on the rising edge of RESET#. Changing state at any other time has no effect. Table 4-7: Summary of Power-On/Reset Options S1D13A04 Configuration Input Power-On/Reset State 1 (connected to IO VDD) Select host bus interface as follows: CNF4 1 0 1 0 1 0 1 0 1 0 1 0 1 0 X CNF2 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 CNF1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 CNF0 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 Host Bus SH-4/SH-3 interface, Big Endian SH-4/SH-3 interface, Little Endian MC68K #1, Big Endian Reserved MC68K #2, Big Endian Reserved Generic #1, Big Endian Generic #1, Little Endian Reserved Generic #2, Little Endian REDCAP2, Big Endian Reserved DragonBall (MC68EZ328/MC68VZ328), Big Endian Reserved Reserved 0 (connected to VSS) CNF4,CNF[2:0] CNF3 CNF5 (see note) CNF6 Reserved. Must be set to 1. WAIT# is active high CLKI to BCLK divide ratio 2:1 WAIT# is active low CLKI to BCLK divide ratio 1:1 Note If CNF5 = 1, the WAIT# pin should be tied low using a pull-down resistor. If CNF5 = 0, the WAIT# pin should be tied high using a pull-up resistor. If WAIT# is not used, this pin should be tied either high or low using a pull-up or pull-down resistor. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 31 4.5 Host Bus Interface Pin Mapping Table 4-8: Host Bus Interface Pin Mapping S1D13A04 Pin Name AB[17:1] AB0 DB[15:0] CS# M/R# CLKI BS# RD/WR# RD# WE0# WE1# WAIT# RESET# BUSCLK BUSCLK Connected to IO VDD RD# WE# BHE# WAIT# RESET# CKIO BS# RD/WR# RD# WE0# WE1# WAIT#/ RDY# RESET# Connected to IO VDD RD1# RD0# WE0# WE1# WAIT# RESET# Generic #1 Generic #2 Hitachi SH-3 /SH-4 A[17:1] A0 1 Motorola MC68K #1 A[17:1] LDS# D[15:0] External Decode CLK AS# R/W# Connected to IO VDD Connected to IO VDD UDS# DTACK# RESET# Motorola MC68K #2 A[17:1] A0 D[15:0]2 Motorola REDCAP2 A[17:1] A0 1 Motorola MC68EZ328/ MC68VZ328 DragonBall A[17:1] A01 D[15:0] CSX CLKO Connected to IO VDD OE LWE UWE DTACK RESET A[17:1] A01 D[15:0] A[17:1] A0 D[15:0] D[15:0] CSn# D[15:0] CSn CLK External Decode External Decode CLK AS# R/W# SIZ1 SIZ0 DS# DSACK1# RESET# Connected to IO VDD R/W OE EB1 EB0 N/A RESET_OUT Note 1 A0 for these busses is not used internally by the S1D13A04 and should be connected to VSS. 2 If the target MC68K bus is 32-bit, then these signals should be connected to D[31:16]. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 32 Epson Research and Development Vancouver Design Center 4.6 LCD Interface Pin Mapping Table 4-9: LCD Interface Pin Mapping Monochrome Passive Panel Pin Name 4-bit FPFRAME FPLINE FPSHIFT DRDY FPDAT0 FPDAT1 FPDAT2 FPDAT3 FPDAT4 FPDAT5 FPDAT6 FPDAT7 FPDAT8 FPDAT9 FPDAT10 FPDAT11 FPDAT12 FPDAT13 FPDAT14 FPDAT15 FPDAT16 FPDAT17 GPIO0 GPIO1 GPIO2 GPIO3 Single 8-bit 4-bit Color Passive Panel Single Format 1 Format 2 Color TFT Panel Others 9-bit 12-bit 18-bit `Direct' HR-TFT1 18-bit SPS LP DCLK GPO2 R5 R4 R3 G5 G4 G3 B5 B4 B3 R2 R1 R0 G2 G1 G0 B2 B1 B0 PS CLS REV SPL 8-bit driven 0 driven 0 driven 0 driven 0 D0 D1 D2 D3 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 MOD D0 D1 D2 D3 D4 D5 D6 D7 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 D0 (R2)3 D1 (B1)3 D2 (G1)3 D3 (R1)3 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 FPSHIFT2 D0 (B5)3 D1 (R5)3 D2 (G4)3 D3 (B3)3 D4 (R3)3 D5 (G2)3 D6 (B1)3 D7 (R1)3 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 8-bit 16-Bit FPFRAME FPLINE FPSHIFT MOD D0 (G3)3 D0 (R6)3 D1 (R3)3 D1 (G5)3 D2 (B2)3 D2 (B4)3 D3 (G2)3 D3 (R4)3 D4 (R2)3 D8 (B5)3 D5 (B1)3 D9 (R5)3 D6 (G1)3 D10 (G4)3 D7 (R1)3 D11 (B3)3 driven 0 D4 (G3)3 driven 0 D5 (B2)3 driven 0 D6 (R2)3 driven 0 D7 (G1)3 driven 0 D12 (R3)3 driven 0 D13 (G2)3 driven 0 D14 (B1)3 driven 0 D15 (R1)3 driven 0 driven 0 driven 0 driven 0 GPIO0 GPIO1 GPIO2 GPIO3 R2 R1 R0 G2 G1 G0 B2 B1 B0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 DRDY R3 R2 R1 G3 G2 G1 B3 B2 B1 R0 driven 0 driven 0 G0 driven 0 driven 0 B0 driven 0 driven 0 R5 R4 R3 G5 G4 G3 B5 B4 B3 R2 R1 R0 G2 G1 G0 B2 B1 B0 Note GPIO pins default to inputs at reset and require special configuration using REG[64h] when the `Direct' HR-TFT interface is desired. 2 When the `Direct' HR-TFT interface is selected (REG[0Ch] bits 1-0 = 10), DRDY becomes a general purpose output (GPO) controllable using the `Direct' HR-TFT LCD Interface GPO Control bit (REG[14h] bit 0). This GPO can be used to control the HR-TFT MOD signal if required. For further information, see the bit description for REG[14h] bit 0. 3 These pin mappings use signal names commonly used for each panel type, however signal names may differ between panel manufacturers. The values shown in brackets represent the color components as mapped to the corresponding FPDATxx signals at the first valid edge of FPSHIFT. For further FPDATxx to LCD interface mapping, see Section 6.4, "Display Interface" on page 56. 1 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 33 5 D.C. Characteristics Note When applying Supply Voltages to the S1D13A04, Core VDD must be applied to the chip before, or simultaneously with IO VDD, or damage to the chip may result. Table 5-1: Absolute Maximum Ratings Symbol Core VDD IO VDD VIN VOUT TSTG TSOL Parameter Supply Voltage Supply Voltage Input Voltage Output Voltage Storage Temperature Solder Temperature/Time VSS - 0.3 to 3.0 VSS - 0.3 to 4.0 VSS - 0.3 to IO VDD + 0.5 VSS - 0.3 to IO VDD + 0.5 -65 to 150 260 for 10 sec. max at lead Rating Units V V V V C C Table 5-2: Recommended Operating Conditions Symbol Core VDD IO VDD VIN TOPR Parameter Supply Voltage Supply Voltage Input Voltage Operating Temperature Condition VSS = 0 V VSS = 0 V VSS = 0 V Min 2.25 3.0 VSS VSS -40 25 2.5 3.3 Typ Max 2.75 3.6 IO VDD CORE VDD 85 C Units V V V V 1.8 (note 1) 2.0 (note 1) 2.2 (note 1) 1. When Core VDD is 2.0V 10%, the MCLK must be less than or equal to 30MHz (MCLK 30MHz) Table 5-3: Electrical Characteristics for VDD = 3.3V typical Symbol IDDS IIZ IOZ VOH Parameter Quiescent Current Input Leakage Current Output Leakage Current High Level Output Voltage Condition Quiescent Conditions -1 -1 VDD = min. IOH = -3mA (Type 1) -6mA (Type 2) VDD = min. IOL = 3mA (Type 1) 6mA (Type 2) LVTTL Level, VDD = max LVTTL Level, VDD = min VIN = VDD VDD - 0.4 Min Typ Max 170 1 1 Units A A A V VOL VIH VIL RPD CI CO CIO Low Level Output Voltage High Level Input Voltage Low Level Input Voltage Pull Down Resistance Input Pin Capacitance Output Pin Capacitance Bi-Directional Pin Capacitance 0.4 2.0 20 50 0.8 120 10 10 10 V V V k pF pF pF Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 34 Epson Research and Development Vancouver Design Center 6 A.C. Characteristics Conditions: IO VDD = 3.3V 10% TA = -40 C to 85 C Trise and Tfall for all inputs must be < 5 nsec (10% ~ 90%) CL = 50pF (Bus/MPU Interface) CL = 0pF (LCD Panel Interface) 6.1 Clock Timing 6.1.1 Input Clocks Clock Input Waveform t PWH t PWL 90% V IH VIL 10% tr t TOSC f Figure 6-1: Clock Input Requirements Table 6-1: Clock Input Requirements for CLKI when CLKI to BCLK divide > 1 Symbol fOSC TOSC tPWH tPWL tf tr Input Clock period (CLKI) Input Clock Pulse Width High (CLKI) Input Clock Pulse Width Low (CLKI) Input Clock Fall Time (10% - 90%) Input Clock Rise Time (10% - 90%) Parameter Input Clock Frequency (CLKI) 1/fOSC 4.5 4.5 5 5 Min Max 100 Units MHz ns ns ns ns ns Note Maximum internal requirements for clocks derived from CLKI must be considered when determining the frequency of CLKI. See Section 6.1.2, "Internal Clocks" on page 35 for internal clock requirements. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 35 Table 6-2: Clock Input Requirements for CLKI when CLKI to BCLK divide = 1 Symbol fOSC TOSC tPWH tPWL tf tr Input Clock period (CLKI) Input Clock Pulse Width High (CLKI) Input Clock Pulse Width Low (CLKI) Input Clock Fall Time (10% - 90%) Input Clock Rise Time (10% - 90%) Parameter Input Clock Frequency (CLKI) 1/fOSC 3 3 5 5 Min Max 66 Units MHz ns ns ns ns ns Note Maximum internal requirements for clocks derived from CLKI must be considered when determining the frequency of CLKI. See Section 6.1.2, "Internal Clocks" on page 35 for internal clock requirements. Table 6-3: Clock Input Requirements for CLKI2 Symbol fOSC TOSC tPWH tPWL tf tr Input Clock period (CLKI2) Input Clock Pulse Width High (CLKI2) Input Clock Pulse Width Low (CLKI2) Input Clock Fall Time (10% - 90%) Input Clock Rise Time (10% - 90%) Parameter Input Clock Frequency (CLKI2) 1/fOSC 3 3 5 5 Min Max 66 Units MHz ns ns ns ns ns Note Maximum internal requirements for clocks derived from CLKI2 must be considered when determining the frequency of CLKI2. See Section 6.1.2, "Internal Clocks" on page 35 for internal clock requirements. 6.1.2 Internal Clocks Table 6-4: Internal Clock Requirements Symbol fBCLK fMCLK fPCLK fPWMCLK Bus Clock frequency Memory Clock frequency Pixel Clock frequency PWM Clock frequency Parameter Min Max 66 50 (note 1,note 2) 50 66 Units MHz MHz MHz MHz 1. When COREVDD = 2.0V 10% fMCLK max = 30MHz. 2. MCLK is derived from BCLK, therefore when BCLK is greater than 50MHz, MCLK must be divided using REG[04h] bits 5-4. Note For further information on internal clocks, refer to Section 7, "Clocks" on page 84. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 36 Epson Research and Development Vancouver Design Center 6.2 CPU Interface Timing 6.2.1 Generic #1 Interface Timing (e.g. Epson EOC33) TCLK CLK t1 A[16:1], M/R# t2 CS# t14 t3 WE0#, WE1#, RD0#, RD1# t4 WAIT# t6 D[15:0] (write) t5 D[15:0] (read) valid valid t13 t12 t11 t9 t10 t8 t7 Figure 6-2: Generic #1 Interface Timing S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 37 Table 6-5: Generic #1 Interface Timing Symbol fCLK TCLK t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 Bus clock frequency Bus clock period A[16:1], M/R# setup to first CLK rising edge where CS# = 0 and either RD0#, RD1# = 0 or WE0#, WE1# = 0 CS# setup to CLK rising edge RD0#, RD1#, WE0#, WE1# setup to CLK rising edge RD0#, RD1# or WE0#, WE1# state change to WAIT# driven low RD0#, RD1# falling edge to D[15:0] driven (read cycle) D[15:0] setup to 4th rising CLK edge after CS#=0 and WE0#, WE1#=0 A[16:1], M/R# and CS# hold from RD0#, RD1#, WE0#, WE1# rising edge CS# deasserted to reasserted WAIT# rising edge to RD0#, RD1#, WE0#, WE1# rising edge WE0#, WE1#, RD0#, RD1# deasserted to reasserted Rising edge of either RD0#, RD1# or WE0#, WE1# to WAIT# high impedance D[15:0] hold from WE0#, WE1# rising edge (write cycle) D[15:0] hold from RD0#, RD1# rising edge (read cycle) Cycle Length 2 1 5 1/fCLK 9 9 1 1 2 1 0 0 0 1 0.5 10 10 Parameter Min Max 50 Unit MHz ns ns ns ns ns ns TCLK ns ns ns TCLK TCLK ns ns TCLK Table 6-6: Generic #1 Interface Truth Table for Little Endian WE0# 0 0 1 1 1 1 WE1# 0 1 0 1 1 1 RD0# 1 1 1 0 0 1 RD1# 1 1 1 0 1 0 D[15:8] valid valid valid valid D[7:0] valid valid valid valid 16-bit write 8-bit write; data on low byte (even byte address1) 8-bit write; data on high byte (odd byte address1) 16-bit read 8-bit read; data on low byte (even byte address1) 8-bit read; data on high byte (odd byte address1) Comments Table 6-7: Generic #1 Interface Truth Table for Big Endian WE0# 0 0 1 1 1 1 WE1# 0 1 0 1 1 1 RD0# 1 1 1 0 0 1 RD1# 1 1 1 0 1 0 D[15:8] valid valid valid valid D[7:0] valid valid valid valid 16-bit write 8-bit write; data on low byte (odd byte address1) 8-bit write; data on high byte (even byte address1) 16-bit read 8-bit read; data on low byte (odd byte address1) 8-bit read; data on high byte (even byte address1) Comments 1. Because A0 is not used internally, all addresses are seen by the S1D13A04 as even addresses (16-bit word address aligned on even byte addresses). Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 38 Epson Research and Development Vancouver Design Center 6.2.2 Generic #2 Interface Timing (e.g. ISA) TBUSCLK BUSCLK t1 A[16:0], M/R#, BHE# t2 CS# t14 t3 WE#, RD# t4 WAIT# t6 D[15:0] (write) t5 D[15:0] (read) valid valid t13 t12 t11 t9 t10 t8 t7 Figure 6-3: Generic #2 Interface Timing S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 39 Table 6-8: Generic #2 Interface Timing Symbol fBUSCLK TBUSCLK t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 Bus clock frequency Bus clock period A[16:0], M/R#, BHE# setup to first BUSCLK rising edge where CS# = 0 and either RD# = 0 or WE# = 0 CS# setup to BUSCLK rising edge RD#, WE# setup to BUSCLK rising edge RD# or WE# state change to WAIT# driven low RD# falling edge to D[15:0] driven (read cycle) D[15:0] setup to 4th rising BUSCLK edge after CS#=0 and WE#=0 A[16:0], M/R#, BHE# and CS# hold from RD#, WE# rising edge CS# deasserted to reasserted WAIT# rising edge to RD#, WE# rising edge WE#, RD# deasserted to reasserted Rising edge of either RD# or WE# to WAIT# high impedance D[15:0] hold from WE# rising edge (write cycle) D[15:0] hold from RD# rising edge (read cycle) Cycle Length 2 1 6 1/fBUSCLK 9 9 1 1 2 1 0 0 0 1 0.5 10 10 Parameter Min Max 50 Unit MHz ns ns ns ns ns ns TBUSCLK ns ns ns TBUSCLK TBUSCLK ns ns TBUSCLK Table 6-9: Generic #2 Interface Truth Table for Little Endian WE# 0 0 0 1 1 1 RD# 1 1 1 0 0 0 BHE# 0 1 0 0 1 0 A0 0 0 1 0 0 1 D[15:8] valid valid valid valid D[7:0] valid valid valid valid 16-bit write 8-bit write at even address 8-bit write at odd address 16-bit read 8-bit read at even address 8-bit read at odd address Comments Note Generic #2 interface only supports Little Endian mode. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 40 Epson Research and Development Vancouver Design Center 6.2.3 Hitachi SH-3 Interface Timing TCKIO CKIO t1 A[16:1], M/R#, RD/WR# t18 t2 t3 BS# t4 CSn# t12 t5 WEn#, RD# t6 WAIT# t7 D[15:0] (write) t8 D[15:0] (read) valid t16 t17 valid t15 t14 t13 t11 t10 t9 Figure 6-4: Hitachi SH-3 Interface Timing Note For this interface, the following formula must apply: MCLK = BCLK 33MHz If a BCLK greater than 33MHz is desired, MCLK must be divided such that MCLK is not greater than 33MHz (see REG[04h] bits 5-4). S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 41 Table 6-10: Hitachi SH-3 Interface Timing Symbol fCKIO TCKIO t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 t15 t16 t17 t18 Bus clock frequency Bus clock period A[16:1], RD/WR# setup to CKIO BS# setup BS# hold CSn# setup WEn#, RD# setup to next CKIO after BS# low Falling edge CSn# to WAIT# driven low D[15:0] setup to 3rd CKIO rising edge after BS# deasserted (write cycle) Falling edge of RD# to D[15:0] driven (read cycle) WE#, RD# deasserted to A[16:1], M/R#, RD/WR# deasserted Rising edge of WAIT# to BS# falling WE#, RD# deasserted to CS# high CKIO rising edge before WAIT# deasserted to WEn#, RD# asserted for next cycle Rising edge of WAIT# to WE#, RD# deasserted Rising edge of CSn# to WAIT# high impedance D[15:0] hold from WEn# deasserted (write cycle) D[15:0] setup to CKIO falling edge (read cycle) Rising edge of RD# to D[15:0] high impedance (read cycle) Cycle Length 2 (note 1) 12 1 4 5 1/fCKIO 1 1 5 1 0 3 1 2 0 TCKIO + 16 0 2 0 0.5 12 10 Parameter Min Max 66 Unit MHz ns ns ns ns ns ns ns TCKIO ns ns ns ns TCKIO ns TCKIO ns ns ns TCKIO 1. The S1D13A04 requires 2ns of write data hold time. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 42 Epson Research and Development Vancouver Design Center 6.2.4 Hitachi SH-4 Interface Timing TCKIO CKIO t1 A[16:1], M/R#, RD/WR# t19 t2 t3 BS# t4 CSn# t12 t5 WEn#, RD# t6 RDY# t7 D[15:0] (write) t8 D[15:0] (read) valid t17 t18 valid t16 t14 t15 t13 t11 t10 t9 Figure 6-5: Hitachi SH-4 Interface Timing S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 43 Table 6-11: Hitachi SH-4 Interface Timing Symbol fCKIO TCKIO t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 t15 t16 t17 t18 t19 Bus clock frequency Bus clock period A[16:1], M/R#, RD/WR# setup to CKIO BS# setup BS# hold CSn# setup WEn#, RD# setup to 2nd CKIO rising edge after BS# low Falling edge CSn# to RDY driven high D[15:0] setup to 3rd CKIO rising edge after BS# deasserted (write cycle) Falling edge RD# to D[15:0] driven (read cycle) WE#,RD# deasserted to A[16:1],M/R#,RD/WR# deasserted RDY falling edge to BS# falling WE#,RD# deasserted to CS# high CKIO rising edge before RDY deasserted to WEn#, RD# asserted for next cycle RDY falling edge to WE#,RD# deasserted Rising edge CSn# to RDY rising edge CKIO falling edge to RDY tristate D[15:0] hold from WEn# deasserted (write cycle) D[15:0] setup to CKIO falling edge (read cycle) Rising edge of RD# to D[15:0] high impedance (read cycle) Cycle Length 1/fCKIO 1 1 5 1 0 3 1 2 0 TCKIO + 11 0 2 0 3 3 3 12 1 4 4 10 9 12 10 Parameter Min Max 66 Unit MHz ns ns ns ns ns ns ns TCKIO ns ns ns ns TCKIO ns ns ns ns ns ns TCKIO Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 44 Epson Research and Development Vancouver Design Center 6.2.5 Motorola MC68K #1 Interface Timing (e.g. MC68000) TCLK CLK t1 A[16:1], R/W#, M/R# t13 t1 CS# t1 AS# t1 UDS#, LDS#, (A0) t7 t2 DTACK# t9 D[15:0] (write) t3 D[15:0] (read) valid t12 valid t11 t10 t8 t5 t6 t4 t4 Figure 6-6: Motorola MC68K #1 Interface Timing S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 45 Table 6-12: Motorola MC68K#1 Interface Timing Symbol fCLK TCLK t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 Bus clock frequency Bus clock period A[16:1], M/R#, R/W# and CS# and AS# and UDS#, LDS# setup to first CLK rising edge CS# and AS# asserted to DTACK# driven UDS# = 0 or LDS# = 0 to D[15:0] driven (read cycle) A[16:1], M/R#, R/W# and CS# hold from AS# rising edge DTACK# falling edge to UDS#, LDS# rising edge UDS#, LDS# deasserted high to reasserted low CLK rising edge to DTACK# high impedance AS# rising edge to DTACK# rising edge D[15:0] valid to 4th CLK rising edge where CS# = 0, AS# = 0 and either UDS# = 0 or LDS# = 0 (write cycle) D[15:0] hold from UDS#, LDS# falling edge (write cycle) UDS#, LDS# rising edge to D[15:0] high impedance (read cycle) D[15:0] valid setup time to 2nd CLK falling edge after DTACK# goes low (read cycle) Cycle Length 3 1 4 2 10 7 0 0 1 TCLK - 2 11 1/fCLK 1 3 10 10 Parameter Min Max 66 Unit MHz ns ns ns ns ns ns TCLK ns ns TCLK ns ns ns TCLK Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 46 Epson Research and Development Vancouver Design Center 6.2.6 Motorola MC68K #2 Interface Timing (e.g. MC68030) TCLK CLK t1 A[16:1], M/R#, R/W#, SIZ[1:0] t16 t1 CS# t1 AS# t1 DS# t10 t2 DSACK1# t12 D[31:16] (write) t3 D[31:16] (read) t14 valid t15 valid t13 t11 t9 t7 t8 t6 t4 t5 Figure 6-7: Motorola MC68K #2 Interface Timing S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 47 Table 6-13: Motorola MC68K#2 Interface Timing Symbol fCLK TCLK t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 t15 t16 Bus clock frequency Bus clock period A[16:0], M/R#, R/W#, SIZ[1:0] and CS# and AS# and DS# setup to first CLK rising edge CS# and AS# asserted low to DSACK1# driven A[1:0], R/W#, SIZ[1:0], DS# asserted to D[15:0] driven A[16:1], M/R#, R/W#, SIZ[1:0] hold from AS# rising edge R/W#, A[1:0], SIZ[1:0] deasserted to R/W#, A[1:0], SIZ[1:0] asserted for next cycle CS# hold from AS# rising edge DS# rising edge to AS# rising edge AS# setup to CLK rising edge DSACK1# falling edge to DS# rising edge CLK rising edge to DSACK1# high impedance AS# rising edge to DSACK1# rising edge D[15:0] setup to 4th CLK rising edge after CS#=0, AS#=0, and UDS#=0 or LDS#=0 D[15:0] hold from A[1:0], R/W#, SIZ[1:0] (write cycle) DSACK1# falling edge to D[15:0] valid (read cycle) DS# rising edge to D[15:0] high impedance (read cycle) Cycle Length 2 6 3 1 1 3 7 0 1 0 0 1 0 TCLK - 2 9 1/fCLK 1 3 10 8 Parameter Min Max 50 Unit MHz ns ns ns ns ns TCLK ns ns ns ns ns ns TCLK ns ns ns TCLK Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 48 Epson Research and Development Vancouver Design Center 6.2.7 Motorola REDCAP2 Interface Timing TCKO CKO t1 A[16:1], R/W#, CS# t12 t2 EBO#, EB1# (write) t3 D[15:0] (write) t5 EB0#, EB1#, OE# (read) t7 D[15:0] (read) t6 valid t11 valid t10 t4 t9 t8 Figure 6-8: Motorola Redcap2 Interface Timing S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 49 Table 6-14: Motorola Redcap2 Interface Timing Symbol fCKO TCKO t1 t2 t3 t4 t5 t6a t6b t6c t6d t7 t8 t9 t10 t11 t12 Bus clock frequency Bus clock period A[16:1], R/W, CSn# setup to CKO rising edge EB0,EB1 setup to CKO rising edge (write) D[15:0] input setup to 4th CKO rising edge after CSn# and EB0 or EB1 asserted low (write cycle) D[15:0] input hold from 4th CKO rising edge after CSn# and EB0 or EB1 asserted low (write cycle) EB0,EB1,OE setup to CKO rising edge (read cycle) 1st CKO rising edge after CSn#, EB0 or EB1,OE asserted low to D[15:0] valid for MCLK = BCLK (read cycle) 1st CKO rising edge after CSn#, EB0 or EB1,OE asserted low to D[15:0] valid for MCLK = BCLK / 2 (read cycle) 1st CKO rising edge after CSn#, EB0 or EB1,OE asserted low to D[15:0] valid for MCLK = BCLK / 3 (read cycle) 1st CKO rising edge after CSn#, EB0 or EB1,OE asserted low to D[15:0] valid for MCLK = BCLK / 4 (read cycle) EB0,EB1,OE falling edge to D[15:0] driven (read cycle) A[16:1], R/W, CSn hold from CKO rising edge EB0, EB1 setup to CKO rising edge (write cycle) CKO falling edge to EB0, EB1, OE deasserted (read) OE, EB0, EB1 deasserted to D[15:0] output high impedance (read) Cycle Length (note 1) 4 0 1 0 1 10 7 10 1/fCKO 1 1 1 11 1 5 8 10 13 11 Parameter Min Max 17 Unit MHz ns ns ns TCKO ns ns TCKO TCKO TCKO TCKO ns ns ns ns ns TCKO 1. The cycle length for the REDCAP interface is fixed. 2. The Read and Write 2D BitBLT functions are not available when using the REDCAP interface. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 50 Epson Research and Development Vancouver Design Center 6.2.8 Motorola Dragonball Interface Timing with DTACK (e.g. MC68EZ328/MC68VZ328) TCLKO CLKO t1 A[16:1] t1 CSX t1 UWE, LWE (write) t1 OE (read) t7 D[15:0] (write) t2 D[15:0] (read) t3 DTACK t11 Valid t9 t10 Valid t12 t8 t5 t6 t13 t5 t4 Figure 6-9: Motorola Dragonball Interface Timing with DTACK S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 51 Table 6-15: Motorola Dragonball Interface Timing with DTACK Symbol fCLKO TCLKO t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 Clock frequency Clock period A[16:1], CSX, UWE, LWE, OE setup to CLKO rising edge CSX and OE asserted low to D[15:0] driven (read cycle) CSX asserted low to DTACK driven A[16:1] hold from CSX rising edge DTACK falling edge to UWE, LWE and CSX rising edge UWE, LWE deasserted to reasserted D[15:0] valid to fourth CLKO rising edge where CSX = 0 and UWE = 0 or LWE = 0 (write cycle) D[15:0] hold from UWE, LWE rising edge (write cycle) DTACK falling edge to D[15:0] valid (read cycle) CSX rising edge to D[15:0] high impedance (read cycle) CSX rising edge to DTACK rising edge CLKO rising edge to DTACK high impedance Cycle Length 2 3 5 0 0 2 1 2 TCLKO + 4 6 9 9 1/fCLKO 1 11 11 Parameter Min Max 33 (note 1) Unit MHz ns ns ns ns ns ns TCLKO TCLKO ns ns ns ns ns TCLKO 1. The MC68VZ328 has a maximum clock frequency of 33MHz. The MC68EZ328 has a maximum clock frequency of 16MHz. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 52 Epson Research and Development Vancouver Design Center 6.2.9 Motorola Dragonball Interface Timing w/o DTACK (e.g. MC68EZ328/MC68VZ328) TCLKO CLKO t1 A[16:1] t1 CSX# t1 UWE#, LWE# (write) t1 OE# (read) t2 D[15:0] (write) t4 t3 D[15:0] (read) valid valid t6 t5 t5 t5 t7 t5 Figure 6-10: Motorola Dragonball Interface Timing w/o DTACK S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 53 Table 6-16: Motorola Dragonball Interface Timing w/o DTACK Symbol fCLKO TCLKO t1 t2 t3 t4a t4b t4c t4d t5 t6 t7 Bus clock frequency Bus clock period A[16:1] and CSX# and UWE#, LWE# and OE# setup to CLKO rising edge D[15:0] valid to 4th CLK rising edge where CSX# = 0 and UWE# = 0 or LWE# = 0 (write cycle) CSX# and OE# asserted low to D[15:0] driven (read cycle) 1st CLKO rising edge after CSX# and OE# asserted to D[15:0] valid for MCLK=BCLK (read cycle) 1st CLKO rising edge after CSX# and OE# asserted to D[15:0] valid for MCLK=BCLK / 2 (read cycle) 1st CLKO rising edge after CSX# and OE# asserted to D[15:0] valid for MCLK=BCLK / 3 (read cycle) (see note 2) 1st CLKO rising edge after CSX# and OE# asserted to D[15:0] valid for MCLK=BCLK / 4 (read cycle) (see note 2) A[16:1] and UWE#, LWE# and OE# and D[15:0] (write) hold from CSX# rising edge CSX# rising edge to D[15:0] high impedance Cycle Length 0 2 9 6 9 1/fCLKO 1 1 11 5 8 10 13 Parameter Min Max 33 (note 1) Unit MHz ns ns TCLKO ns TCLKO TCLKO TCLKO TCLKO ns ns TCLKO 1. The MC68VZ328 has a maximum clock frequency of 33MHz. The MC68EZ328 has a maximum clock frequency of 16MHz. 2. The MC68EZ328 does not support the MCLK = BCLK / 3 and MCLK = BCLK / 4 options. 3. The cycle length for the Dragonball w/o DTACK interface is fixed. 4. The Read and Write 2D BitBLT functions are not available when using the Dragonball w/o DTACK interface. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 54 Epson Research and Development Vancouver Design Center 6.3 LCD Power Sequencing 6.3.1 Passive/TFT Power-On Sequence GPIO0* Power Save Mode Enable** (REG[A0h] bit 0) t2 LCD Signals*** t1 *It is recommended to use the general purpose IO pin GPIO0 to control the LCD bias power. **The LCD power-on sequence is activated by programming the Power Save Mode Enable bit (REG[14h] bit 4) to 0. ***LCD Signals include: FPDAT[17:0], FPSHIFT, FPLINE, FPFRAME, and DRDY. Figure 6-11: Passive/TFT Power-On Sequence Timing Table 6-17: Passive/TFT Power-On Sequence Timing Symbol t1 t2 Parameter LCD signals active to LCD bias active Power Save Mode disabled to LCD signals active Min Note 1 0 Max Note 1 1 BCLK Units 1. t1 is controlled by software and must be determined from the bias power supply delay requirements of the panel connected. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 55 6.3.2 Passive/TFT Power-Off Sequence t1 GPIO0* Power Save Mode Enable** (REG[A0h] bit 0) t2 LCD Signals*** *It is recommended to use the general purpose IO pin GPIO0 to control the LCD bias power. **The LCD power-off sequence is activated by programming the Power Save Mode Enable bit (REG[14h] bit 4) to 1. ***LCD Signals include: FPDAT[17:0], FPSHIFT, FPLINE, FPFRAME, and DRDY. Figure 6-12: Passive/TFT Power-Off Sequence Timing Table 6-18: Passive/TFT Power-Off Sequence Timing Symbol t1 t2 Parameter LCD bias deactivated to LCD signals inactive Power Save Mode enabled to LCD signals low Min Note 1 0 Max Note 1 1 BCLK Units 1. t1 is controlled by software and must be determined from the bias power supply delay requirements of the panel connected. 6.3.3 `Direct' HR-TFT Interface Power-On/Off Sequence For `Direct' HR-TFT Interface Power-On/Off sequence information, see Connecting to the Sharp HR-TFT Panels, document number X37A-G-011-xx. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 56 Epson Research and Development Vancouver Design Center 6.4 Display Interface The timing parameters required to drive a flat panel display are shown below. Timing details for each supported panel type are provided in the remainder of this section. HT HDPS HPS HPW VPS VDPS VPW HDP VT VDP Figure 6-13: Panel Timing Parameters S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 57 Table 6-19: Panel Timing Parameter Definition and Register Summary Symbol HT HDP1 HDPS HPS HPW VT VDP VDPS VPS VPW Description Horizontal Total Horizontal Display Period1 Derived From ((REG[20h] bits 6-0) + 1) x 8 ((REG[24h] bits 6-0) + 1) x 8 For STN panels: ((REG[28h] bits 9-0) + 22) Horizontal Display Period Start Position For TFT panels: ((REG[28h] bits 9-0) + 5) FPLINE Pulse Start Position (REG[2Ch] bits 9-0) + 1 FPLINE Pulse Width (REG[2Ch] bits 22-16) + 1 Vertical Total (REG[30h] bits 9-0) + 1 Vertical Display Period (REG[34h] bits 9-0) + 1 Vertical Display Period Start Position REG[38h] bits 9-0 FPFRAME Pulse Start Position REG[2Ch] bits 9-0 FPFRAME Pulse Width (REG[3Ch] bits 18-16) + 1 Units Ts Lines (HT) 1. For passive panels, the HDP must be a minimum of 32 pixels and must be increased by multiples of 16. For TFT panels, the HDP must be a minimum of 8 pixels and must be increased by multiples of 8. 2. The following formulas must be valid for all panel timings: HDPS + HDP < HT VDPS + VDP < VT Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 58 Epson Research and Development Vancouver Design Center 6.4.1 Generic STN Panel Timing VT (= 1 Frame) VPW FPFRAME VDP FPLINE MOD1(DRDY) FPDAT[17:0] HT (= 1 Line) HPS FPLINE FPSHIFT 1PCLK MOD2(DRDY) HDPS FPDAT[17:0] HDP HPW Figure 6-14: Generic STN Panel Timing S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 59 VT = Vertical Total = [(REG[30h] bits 9-0) + 1] lines VPS = FPFRAME Pulse Start Position = 0 lines, because REG[2Ch] bits 9-0 = 0 VPW = FPFRAME Pulse Width = [(REG[3Ch] bits 18-16) + 1] lines VDPS = Vertical Display Period Start Position = 0 lines, because REG[38h] bits 9-0 = 0 VDP = Vertical Display Period = [(REG[34h] bits 9-0) + 1] lines HT = Horizontal Total = [((REG[20h] bits 6-0) + 1) x 8] pixels HPS = FPLINE Pulse Start Position = [(REG[2Ch] bits 9-0) + 1] pixels HPW = FPLINE Pulse Width = [(REG[2Ch] bits 22-16) + 1] pixels HDPS = Horizontal Display Period Start Position= 22 pixels, because REG[28h] bits 9-0 = 0 HDP = Horizontal Display Period = [((REG[24h] bits 6-0) + 1) x 8] pixels *For passive panels, the HDP must be a minimum of 32 pixels and must be increased by multiples of 16. *HPS must comply with the following formula: HPS > HDP + 22 HPS + HPW < HT *Panel Type Bits (REG[0Ch] bits 1-0) = 00b (STN) *FPFRAME Pulse Polarity Bit (REG[3Ch] bit 23) = 1 (active high) *FPLINE Polarity Bit (REG[2Ch] bit 23) = 1 (active high) *MOD1 is the MOD signal when REG[0Ch] bits 21-16 = 0 (MOD toggles every FPFRAME) *MOD2 is the MOD signal when REG[0Ch] bits 21-16 = n (MOD toggles every n FPLINE) Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 60 Epson Research and Development Vancouver Design Center 6.4.2 Single Monochrome 4-Bit Panel Timing VDP VNDP FPFRAME FPLINE DRDY (MOD) FPDAT[7:4] Invalid LINE1 LINE2 LINE3 LINE4 LINE239 LINE240 Invalid LINE1 LINE2 FPLINE DRDY (MOD) HDP HNDP FPSHIFT FPDAT7 FPDAT6 FPDAT5 FPDAT4 Invalid Invalid Invalid Invalid 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-317 1-318 1-319 1-320 Invalid Invalid Invalid Invalid * Diagram drawn with 2 FPLINE vertical blank period Example timing for a 320x240 panel Figure 6-15: Single Monochrome 4-Bit Panel Timing VDP VNDP = Vertical Display Period = (REG[34h] bits 9:0) + 1 Lines = Vertical Non-Display Period = VT - VDP = (REG[30h] bits 9:0) - (REG[34h] bits 9:0) Lines = Horizontal Display Period = ((REG[24h] bits 6:0) + 1) x 8Ts = Horizontal Non-Display Period = HT - HDP = (((REG[20h] bits 6:0) + 1) x 8Ts) - (((REG[24h] bits 6:0) + 1) x 8Ts) HDP HNDP S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 61 Sync Timing FPFRAME t1 t2 t4 FPLINE t5 DRDY (MOD) Data Timing FPLINE t6 t8 t7 FPSHIFT t12 FPDAT[7:4] t14 t3 t9 t11 t10 t13 1 2 Figure 6-16: Single Monochrome 4-Bit Panel A.C. Timing Table 6-20: Single Monochrome 4-Bit Panel A.C. Timing Symbol t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 Parameter FPFRAME setup to FPLINE falling edge FPFRAME hold from FPLINE falling edge FPLINE period FPLINE pulse width MOD transition to FPLINE rising edge FPSHIFT falling edge to FPLINE rising edge FPSHIFT falling edge to FPLINE falling edge FPLINE falling edge to FPSHIFT falling edge FPSHIFT period FPSHIFT pulse width low FPSHIFT pulse width high FPDAT[7:4] setup to FPSHIFT falling edge FPDAT[7:4] hold to FPSHIFT falling edge FPLINE falling edge to FPSHIFT rising edge Min note 2 note 3 note 4 note 5 note 6 note 7 t6 + t4 t14 + 2 4 2 2 1 2 note 8 Typ Max Units Ts (note 1) Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts 1. 2. 3. 4. 5. 6. 7. 8. Ts t1min t2min t3min t4min t5min t6min t14min = pixel clock period = HPS + t4min = t3min - (HPS + t4min) = HT = HPW = HPS - 1 = HPS - (HDP + HDPS) + 2, if negative add t3min = HDPS - (HPS + t4min), if negative add t3min Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 62 Epson Research and Development Vancouver Design Center 6.4.3 Single Monochrome 8-Bit Panel Timing VDP VNDP FPFRAME FPLINE DRDY (MOD) FPDAT[7:0] Invalid LINE1 LINE2 LINE3 LINE4 LINE479 LINE480 Invalid LINE1 LINE2 FPLINE DRDY (MOD) HDP HNDP FPSHIFT FPDAT7 FPDAT6 FPDAT5 FPDAT4 FPDAT3 FPDAT2 FPDAT1 FPDAT0 Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 1-15 1-16 1-633 1-634 1-635 1-636 1-637 1-638 1-639 1-640 Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid * Diagram drawn with 2 FPLINE vertical blank period Example timing for a 640x480 panel Figure 6-17: Single Monochrome 8-Bit Panel Timing VDP VNDP = Vertical Display Period = (REG[34h] bits 9:0) + 1 Lines = Vertical Non-Display Period = VT - VDP = (REG[30h] bits 9:0) - (REG[34h] bits 9:0) Lines = Horizontal Display Period = ((REG[24h] bits 6:0) + 1) x 8Ts = Horizontal Non-Display Period = HT - HDP = (((REG[20h] bits 6:0) + 1) x 8Ts) - (((REG[24h] bits 6:0) + 1) x 8Ts) HDP HNDP S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 63 Sync Timing FPFRAME t1 t2 t4 FPLINE t5 DRDY (MOD) Data Timing FPLINE t6 t8 t7 FPSHIFT t12 FPDAT[7:0] 1 t14 t3 t9 t11 t10 t13 2 Figure 6-18: Single Monochrome 8-Bit Panel A.C. Timing Table 6-21: Single Monochrome 8-Bit Panel A.C. Timing Symbol t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 Parameter FPFRAME setup to FPLINE falling edge FPFRAME hold from FPLINE falling edge FPLINE period FPLINE pulse width MOD transition to FPLINE rising edge FPSHIFT falling edge to FPLINE rising edge FPSHIFT falling edge to FPLINE falling edge FPLINE falling edge to FPSHIFT falling edge FPSHIFT period FPSHIFT pulse width low FPSHIFT pulse width high FPDAT[7:0] setup to FPSHIFT falling edge FPDAT[7:0] hold to FPSHIFT falling edge FPLINE falling edge to FPSHIFT rising edge Min note 2 note 3 note 4 note 5 note 6 note 7 t6 + t4 t14 + 4 8 4 4 4 4 note 8 Typ Max Units Ts (note 1) Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts 1. 2. 3. 4. 5. 6. 7. 8. Ts t1min t2min t3min t4min t5min t6min t14min = pixel clock period = HPS + t4min = t3min - (HPS + t4min) = HT = HPW = HPS - 1 = HPS - (HDP + HDPS) + 4, if negative add t3min = HDPS - (HPS + t4min), if negative add t3min Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 64 Epson Research and Development Vancouver Design Center 6.4.4 Single Color 4-Bit Panel Timing VDP VNDP FPFRAME FPLINE DRDY (MOD) FPDAT[7:4] Invalid LINE1 LINE2 LINE3 LINE4 LINE239 LINE240 Invalid LINE1 LINE2 FPLINE DRDY (MOD) HDP .5Ts .5Ts .5Ts .5Ts .5Ts .5Ts 2.5Ts .5Ts .5Ts .5Ts .5Ts HNDP .5Ts FPSHIFT Invalid Invalid Invalid Invalid .5Ts .5Ts .5Ts .5Ts .5Ts .5Ts .5Ts FPDAT7 FPDAT6 FPDAT5 Notes: 1-R1 1-G1 1-B1 1-R2 1-G2 1-B2 1-R3 1-G3 1-B3 1-R4 1-G4 1-B4 1-B319 1-R320 1-G320 1-B320 Invalid Invalid Invalid Invalid FPDAT4 - FPSHIFT uses extended low states in order to process 8 pixels in 6 FPSHIFT clocks - Ts = Pixel clock period (PCLK) - Diagram drawn with 2 FPLINE vertical blank period - Example timing for a 320x240 panel Figure 6-19: Single Color 4-Bit Panel Timing VDP VNDP = Vertical Display Period = (REG[34h] bits 9:0) + 1 Lines = Vertical Non-Display Period = VT - VDP = (REG[30h] bits 9:0) - (REG[34h] bits 9:0) Lines = Horizontal Display Period = ((REG[24h] bits 6:0) + 1) x 8Ts = Horizontal Non-Display Period = HT - HDP = (((REG[20h] bits 6:0) + 1) x 8Ts) - (((REG[24h] bits 6:0) + 1) x 8Ts) HDP HNDP S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 65 Sync Timing FPFRAME t1 t2 t4 FPLINE t5 DRDY (MOD) Data Timing FPLINE t6 t8 t7 FPSHIFT t12 FPDAT[7:4] t14 t3 t9 t11 t10 t13 1 2 Figure 6-20: Single Color 4-Bit Panel A.C. Timing Table 6-22: Single Color 4-Bit Panel A.C. Timing Symbol t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 Parameter FPFRAME setup to FPLINE falling edge FPFRAME hold from FPLINE falling edge FPLINE period FPLINE pulse width MOD transition to FPLINE rising edge FPSHIFT falling edge to FPLINE rising edge FPSHIFT falling edge to FPLINE falling edge FPLINE falling edge to FPSHIFT falling edge FPSHIFT period FPSHIFT pulse width low FPSHIFT pulse width high FPDAT[7:4] setup to FPSHIFT falling edge FPDAT[7:4] hold to FPSHIFT falling edge FPLINE falling edge to FPSHIFT rising edge Min note 2 note 3 note 4 note 5 note 6 note 7 t6 + t4 t14 + 0.5 1 0.5 0.5 0.5 0.5 note 8 Typ Max Units Ts (note 1) Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts 1. 2. 3. 4. 5. 6. 7. 8. Ts t1min t2min t3min t4min t5min t6min t14min = pixel clock period = HPS + t4min = t3min - (HPS + t4min) = HT = HPW = HPS - 1 = HPS - (HDP + HDPS) + 1.5), if negative add t3min = HDPS - (HPS + t4min) + 1, if negative add t3min Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 66 Epson Research and Development Vancouver Design Center 6.4.5 Single Color 8-Bit Panel Timing (Format 1) VDP VNDP FPFRAME FPLINE FPDAT[7:0] Invalid LINE1 LINE2 LINE3 LINE4 LINE239 LINE240 Invalid LINE1 LINE2 FPLINE HDP HNDP 2Ts 2Ts 4Ts 4Ts 2Ts 2Ts 2Ts 2Ts 2Ts 1R316 1B316 1G317 1R318 1B318 1G319 1R320 1B320 1R316 FPSHIFT FPSHIFT2 2Ts 2Ts 4Ts 4Ts 2Ts 2Ts 2Ts 2Ts 4Ts 2Ts 2Ts 4Ts 2Ts 4Ts 4Ts 2Ts 2Ts 2Ts 2Ts 2Ts 2Ts 2Ts 2Ts 2Ts 2Ts 2Ts Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid FPDAT7 FPDAT6 FPDAT5 FPDAT4 FPDAT3 FPDAT2 FPDAT1 FPDAT0 Notes: Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid 1-R1 1-G1 1-G6 1-B6 1-B11 1-R12 1-B1 1-R2 1-R7 1-G7 1-G12 1-B12 1-G2 1-B2 1-B7 1-R8 1-R13 1-G13 1-R3 1-G3 1-G8 1-B8 1-B13 1-R14 1-B3 1-R4 1-R9 1-G9 1-G14 1-B14 1-G4 1-B4 1-B9 1-R10 1-R15 1-G15 1-R5 1-G5 1-G10 1-B10 1-B15 1-R16 1-B5 1-R6 1-R11 1-G11 1-G16 1-B16 - The duty cycle of FPSHIFT changes in order to process 16 pixels in 6 FPSHIFT/FPSHIFT2 rising edges - Ts = Pixel clock period (PCLK) - Diagram drawn with 2 FPLINE vertical blank period - Example timing for a 320x240 panel Figure 6-21: Single Color 8-Bit Panel Timing (Format 1) VDP VNDP = Vertical Display Period = (REG[34h] bits 9:0) + 1 Lines = Vertical Non-Display Period = VT - VDP = (REG[30h] bits 9:0) - (REG[34h] bits 9:0) Lines = Horizontal Display Period = ((REG[24h] bits 6:0) + 1) x 8Ts = Horizontal Non-Display Period = HT - HDP = (((REG[20h] bits 6:0) + 1) x 8Ts) - (((REG[24h] bits 6:0) + 1) x 8Ts) HDP HNDP S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 67 Sync Timing FPFRAME t1 t2 t4 FPLINE Data Timing t3 FPLINE t6a t6b t7a FPSHIFT t7b FPSHIFT2 t12 t13 t12 t13 t8 t14 t11 t9 t10 FPDAT[7:0] 1 2 Figure 6-22: Single Color 8-Bit Panel A.C. Timing (Format 1) Table 6-23: Single Color 8-Bit Panel A.C. Timing (Format 1) Symbol t1 t2 t3 t4 t6a t6b t7a t7b t8 t9 t10 t11 t12 t13 t14 Parameter FPFRAME setup to FPLINE falling edge FPFRAME hold from FPLINE falling edge FPLINE period FPLINE pulse width FPSHIFT falling edge to FPLINE rising edge FPSHIFT2 falling edge to FPLINE rising edge FPSHIFT falling edge to FPLINE falling edge FPSHIFT2 falling edge to FPLINE falling edge FPLINE falling edge to FPSHIFT rising, FPSHIFT2 falling edge FPSHIFT2, FPSHIFT period FPSHIFT2, FPSHIFT pulse width low FPSHIFT2, FPSHIFT pulse width high FPDAT[7:0] setup to FPSHIFT2, FPSHIFT falling edge FPDAT[7:0] hold from FPSHIFT2, FPSHIFT falling edge FPLINE falling edge to FPSHIFT rising edge Min note 2 note 3 note 4 note 5 note 6 note 7 t6a + t4 t6b + t4 t14 + 2 4 2 2 1 1 note 8 Typ Max Units Ts (note 1) Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts 6 1. 2. 3. 4. 5. 6. 7. 8. Ts t1min t2min t3min t4min t6amin t6bmin t14min = pixel clock period = HPS + t4min = t3min - (HPS + t4min) = HT = HPW = HPS - (HDP + HDPS), if negative add t3min = HPS - (HDP + HDPS) + 2, if negative add t3min = HDPS - (HPS + t4min), if negative add t3min Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 68 Epson Research and Development Vancouver Design Center 6.4.6 Single Color 8-Bit Panel Timing (Format 2) VDP VNDP FPFRAME FPLINE DRDY (MOD) FPDAT[7:0] Invalid LINE1 LINE2 LINE3 LINE4 LINE239 LINE240 Invalid LINE1 LINE2 FPLINE DRDY (MOD) HDP HNDP 2Ts Ts Ts Ts 1-G318 1-B318 1-R319 1-G319 1-B319 1-R320 1-G320 1-B320 Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid 2Ts FPSHIFT FPDAT7 FPDAT6 FPDAT5 FPDAT4 FPDAT3 FPDAT2 FPDAT1 FPDAT0 Notes: Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid 2Ts Ts 1-R1 1-G1 1-B1 1-R2 1-G2 1-B2 1-R3 1-G3 Ts Ts 1-B3 1-R4 1-G4 1-B4 1-R5 1-G 5 1-B5 1-R6 2Ts Ts 1-G6 1-B6 1-R7 1-G7 1-B7 1-R8 1-G8 1-B8 2Ts Ts Ts Ts 2Ts - The duty cycle of FPSHIFT changes in order to process 8 pixels in 3 FPSHIFT rising clocks - Ts = Pixel clock period (PCLK) - Diagram drawn with 2 FPLINE vertical blank period - Example timing for a 320x240 panel Figure 6-23: Single Color 8-Bit Panel Timing (Format 2) VDP VNDP = Vertical Display Period = (REG[34h] bits 9:0) + 1 Lines = Vertical Non-Display Period = VT - VDP = (REG[30h] bits 9:0) - (REG[34h] bits 9:0) Lines = Horizontal Display Period = ((REG[24h] bits 6:0) + 1) x 8Ts = Horizontal Non-Display Period = HT - HDP = (((REG[20h] bits 6:0) + 1) x 8Ts) - (((REG[24h] bits 6:0) + 1) x 8Ts) HDP HNDP S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 69 Sync Timing FPFRAME t1 t2 t4 FPLINE t5 DRDY (MOD) Data Timing FPLINE t6 t8 t7 FPSHIFT t12 FPDAT[7:0] t14 t3 t9 t11 t10 t13 1 2 Figure 6-24: Single Color 8-Bit Panel A.C. Timing (Format 2) Table 6-24: Single Color 8-Bit Panel A.C. Timing (Format 2) Symbol t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 Parameter FPFRAME setup to FPLINE falling edge FPFRAME hold from FPLINE falling edge FPLINE period FPLINE pulse width MOD transition to FPLINE rising edge FPSHIFT falling edge to FPLINE rising edge FPSHIFT falling edge to FPLINE falling edge FPLINE falling edge to FPSHIFT falling edge FPSHIFT period FPSHIFT pulse width low FPSHIFT pulse width high FPDAT[7:0] setup to FPSHIFT falling edge FPDAT[7:0] hold to FPSHIFT falling edge FPLINE falling edge to FPSHIFT rising edge Min note 2 note 3 note 4 note 5 note 6 note 7 t6 + t4 t14 + 2 2 1 1 1 1 note 8 Typ Max Units Ts (note 1) Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts 1. 2. 3. 4. 5. 6. 7. 8. Ts t1min t2min t3min t4min t5min t6min t14min = pixel clock period = HPS + t4min = t3min - (HPS + t4min) = HT = HPW = HPS - 1 = HPS - (HDP + HDPS) + 1, if negative add t3min = HDPS - (HPS + t4min), if negative add t3min Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 70 Epson Research and Development Vancouver Design Center 6.4.7 Single Color 16-Bit Panel Timing VDP VNDP FPFRAME FPLINE DRDY (MOD) FPDAT[15:0] Invalid LINE1 LINE2 LINE3 LINE4 LINE479 LINE480 Invalid LINE1 LINE2 FPLINE DRDY (MOD) HDP HNDP 3Ts 3Ts 2Ts 2Ts 3Ts 3Ts 1-G635 1-G636 1-R637 1-B637 1-G638 1-R639 1-B639 1-G640 1-R636 1-B636 1-G637 1-R638 1-B638 1-G639 1-R640 1-B640 3Ts FPSHIFT FPDAT15 FPDAT14 FPDAT13 FPDAT12 FPDAT7 FPDAT6 FPDAT5 FPDAT4 FPDAT11 FPDAT10 FPDAT9 FPDAT8 FPDAT3 FPDAT2 FPDAT1 FPDAT0 Notes: Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid 3Ts 3Ts 1-R1 1-B1 1-G2 1-R3 1-B3 1-G4 1-R5 1-B5 1-G1 1-R2 1-B2 1-G3 1-R4 1-B4 1-G5 1-R6 2Ts 3Ts 3Ts 3Ts 2Ts 3Ts 3Ts 3Ts 2Ts 3Ts 2Ts 1-G6 1-B11 1-R7 1-B7 1-G8 1-R9 1-B9 1-G10 1-R11 1-B6 1-G7 1-R8 1-B8 1-G9 1-R10 1-B10 1-G11 1-G12 1-R13 1-B13 1-G14 1-R15 1-B15 1-G16 1-R12 1-B12 1-G13 1-R14 1-B14 1-G15 1-R16 1-B16 Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid Invalid - The duty cycle of FPSHIFT changes in order to process 16 pixels in 3 FPSHIFT rising clocks - Ts = Pixel clock period (PCLK) - Diagram drawn with 2 FPLINE vertical blank period - Example timing for a 640x480 panel Figure 6-25: Single Color 16-Bit Panel Timing VDP VNDP = Vertical Display Period = (REG[34h] bits 9:0) + 1 Lines = Vertical Non-Display Period = VT - VDP = (REG[30h] bits 9:0) - (REG[34h] bits 9:0) Lines = Horizontal Display Period = ((REG[24h] bits 6:0) + 1) x 8Ts = Horizontal Non-Display Period = HT - HDP = (((REG[20h] bits 6:0) + 1) x 8Ts) - (((REG[24h] bits 6:0) + 1) x 8Ts) HDP HNDP S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 71 Sync Timing FPFRAME t1 t2 t4 FPLINE t5 DRDY (MOD) Data Timing FPLINE t6 t8 t7 FPSHIFT t12 FPDAT[15:0] t14 t3 t9 t11 t10 t13 1 2 Figure 6-26: Single Color 16-Bit Panel A.C. Timing Table 6-25: Single Color 16-Bit Panel A.C. Timing Symbol t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 Parameter FPFRAME setup to FPLINE falling edge FPFRAME hold from FPLINE falling edge FPLINE period FPLINE pulse width MOD transition to FPLINE rising edge FPSHIFT falling edge to FPLINE rising edge FPSHIFT falling edge to FPLINE falling edge FPLINE falling edge to FPSHIFT falling edge FPSHIFT period FPSHIFT pulse width low FPSHIFT pulse width high FPDAT[15:0] setup to FPSHIFT rising edge FPDAT[15:0] hold to FPSHIFT rising edge FPLINE falling edge to FPSHIFT rising edge Min note 2 note 3 note 4 note 5 note 6 note 7 t6 + t4 t14 + 3 5 2 2 2 2 note 8 Typ Max Units Ts (note 1) Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts 1. 2. 3. 4. 5. 6. 7. 8. Ts t1min t2min t3min t4min t5min t6min t14min = pixel clock period = HPS + t4min = t3min - (HPS + t4min) = HT = HPW = HPS - 1 = HPS - (HDP + HDPS) + 2, if negative add t3min = HDPS - (HPS + t4min), if negative add t3min Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 72 Epson Research and Development Vancouver Design Center 6.4.8 Generic TFT Panel Timing VT (= 1 Frame) VPS FPFRAME VDPS FPLINE VDP VPW DRDY FPDAT[17:0] HT (= 1 Line) HPS FPLINE FPSHIFT DRDY HDPS FPDAT[17:0] invalid HDP invalid HPW Figure 6-27: Generic TFT Panel Timing VT VPS VPW VDPS VDP HT HPS HPW HDPS HDP = Vertical Total = [(REG[30h] bits 9-0) + 1] lines = FPFRAME Pulse Start Position = (REG[3Ch] bits 9-0) lines = FPFRAME Pulse Width = [(REG[3Ch] bits 18-16) + 1] lines = Vertical Display Period Start Position= (REG[38h] bits 9-0) lines = Vertical Display Period = [(REG[34h] bits 9-0) + 1] lines = Horizontal Total = [((REG[20h] bits 6-0) + 1) x 8] pixels = FPLINE Pulse Start Position = [(REG[2Ch] bits 9-0) + 1] pixels = FPLINE Pulse Width = [(REG[2Ch] bits 22-16) + 1] pixels = Horizontal Display Period Start Position= [(REG[28h] bits 9-0) + 5] pixels = Horizontal Display Period = [((REG[24h] bits 6-0) + 1) x 8] pixels *For TFT panels, the HDP must be a minimum of 8 pixels and must be increased by multiples of 8. *Panel Type Bits (REG[0Ch] bits 1-0) = 01 (TFT) *FPLINE Pulse Polarity Bit (REG[2Ch] bit 23) = 0 (active low) *FPFRAME Polarity Bit (REG[3Ch] bit 23) = 0 (active low) S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 73 6.4.9 9/12/18-Bit TFT Panel Timing VNDP2 VDP VNDP1 FPFRAME FPLINE FPDAT[17:0] DRDY LINE240 LINE1 LINE480 FPLINE HNDP1 HDP HNDP2 FPSHIFT DRDY FPDAT[17:0] invalid 1-1 1-2 1-320 invalid Note: DRDY is used to indicate the first pixel Example Timing for 18-bit 320x240 panel Figure 6-28: 18-Bit TFT Panel Timing VDP VNDP = Vertical Display Period = VDP Lines = Vertical Non-Display Period = VNDP1 + VNDP2 = VT - VDP Lines = Vertical Non-Display Period 1 = VNDP - VNDP2 Lines = Vertical Non-Display Period 2 = VDPS - VPS Lines = Horizontal Display Period = HDP Ts = Horizontal Non-Display Period = HNDP1 + HNDP2 = HT - HDP Ts = Horizontal Non-Display Period 1 = HDPS - HPS Ts = Horizontal Non-Display Period 2 = HPS - (HDP + HDPS) Ts VNDP1 VNDP2 HDP HNDP if negative add VT HNDP1 HNDP2 if negative add HT if negative add HT Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 74 Epson Research and Development Vancouver Design Center t1 t2 FPFRAME t3 FPLINE t4 FPLINE t5 t6 DRDY t9 t10 t11 FPSHIFT t12 t13 t14 t7 t8 t15 t16 FPDAT[17:0] invalid 1 2 319 320 invalid Note: DRDY is used to indicate the first pixel Figure 6-29: TFT A.C. Timing S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 75 Table 6-26: TFT A.C. Timing Symbol t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 t15 t16 Parameter FPFRAME cycle time FPFRAME pulse width low FPFRAME falling edge to FPLINE falling edge phase difference FPLINE cycle time FPLINE pulse width low FPLINE Falling edge to DRDY active DRDY pulse width DRDY falling edge to FPLINE falling edge FPSHIFT period FPSHIFT pulse width high FPSHIFT pulse width low FPLINE setup to FPSHIFT falling edge DRDY to FPSHIFT falling edge setup time DRDY hold from FPSHIFT falling edge Data setup to FPSHIFT falling edge Data hold from FPSHIFT falling edge Min VT VPW HPS HT HPW note 2 HDP note 3 1 0.5 0.5 0.5 0.5 0.5 0.5 0.5 Typ Max Units Lines Lines Ts (note 1) Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts 250 1. Ts 2. t6min 3. t8min = pixel clock period = HDPS - HPS = HPS - (HDP + HDPS) if negative add HT if negative add HT Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 76 Epson Research and Development Vancouver Design Center 6.4.10 160x160 Sharp `Direct' HR-TFT Panel Timing (e.g. LQ031B1DDxx) FPFRAME (SPS) FPLINE (LP) t2 t3 FPLINE (LP) FPSHIFT (CLK) t5 t6 FPDAT[17:0] t7 t9 GPIO3 (SPL) t11 GPIO1 (CLS) t12 GPIO0 (PS) t10 D1 D2 D3 t8 D160 t1 t4 t13 GPIO2 (REV) Figure 6-30: 160x160 Sharp `Direct' HR-TFT Panel Horizontal Timing S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 77 Table 6-27: 160x160 Sharp `Direct' HR-TFT Horizontal Timing Symbol t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 Parameter FPLINE start position Horizontal total period FPLINE width FPSHIFT period Data setup to FPSHIFT rising edge Data hold from FPSHIFT rising edge Horizontal display start position Horizontal display period FPLINE rising edge to GPIO3 rising edge GPIO3 pulse width GPIO1(GPIO0) pulse width GPIO1 rising edge (GPIO0 falling edge) to FPLINE rise edge GPIO2 toggle edge to FPLINE rise edge Min 180 2 1 0.5 0.5 5 160 4 1 136 4 10 Typ 13 Max 220 Units Ts (note 1) Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts 1. 2. 3. 4. 5. 6. Ts t1typ t2typ t3typ t7typ t8typ = pixel clock period = (REG[2Ch] bits 9-0) + 1 = ((REG[20h] bits 6-0) + 1) x 8 = (REG[2Ch] bits 22-16) + 1 = ((REG[28h] bits 9-0) + 5) - ((REG[2Ch] bits 9-0) + 1) = ((REG[24h] bits 6-0) + 1) x 8 Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 78 Epson Research and Development Vancouver Design Center t1 t2 FPDAT[17:0] t4 FPFRAME (SPS) t5 GPIO1 (CLS) t7 GPIO0 (PS) t9 FPLINE (LP) FPSHIFT (CLK) t10 GPIO1 (CLS) t13 t14 GPIO0 (PS) t8 t6 LINE1 LINE2 t3 LINE160 t11 t12 Figure 6-31: 160x160 Sharp `Direct' HR-TFT Panel Vertical Timing S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 79 Table 6-28: 160x160 Sharp `Direct' HR-TFT Panel Vertical Timing Symbol t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 t14 Parameter Vertical total period Vertical display start position Vertical display period Vertical sync pulse width FPFRAME falling edge to GPIO1 alternate timing start GPIO1 alternate timing period FPFRAME falling edge to GPIO0 alternate timing start GPIO0 alternate timing period GPIO1 first pulse rising edge to FPLINE rising edge GPIO1 first pulse width GPIO1 first pulse falling edge to second pulse rising edge GPIO1 second pulse width GPIO0 falling edge to FPLINE rising edge GPIO0 low pulse width Min 203 Typ 40 160 2 5 4 40 162 4 48 40 48 4 24 Max 264 Units Lines Lines Lines Lines Lines Lines Lines Lines Ts (note 1) Ts Ts Ts Ts Ts 1. Ts = pixel clock period Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 80 Epson Research and Development Vancouver Design Center 6.4.11 320x240 Sharp `Direct' HR-TFT Panel Timing (e.g. LQ039Q2DS01) FPFRAME (SPS) FPLINE (LP) t2 t3 FPLINE (LP) FPSHIFT (CLK) t5 t6 FPDAT[17:0] t7 D1 D2 D3 t8 D320 t1 t4 t9 GPIO3 (SPL) t10 t11 GPIO1 (CLS) t12 GPIO0 (PS) t13 GPIO2 (REV) Figure 6-32: 320x240 Sharp `Direct' HR-TFT Panel Horizontal Timing S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 81 Table 6-29: 320x240 Sharp `Direct' HR-TFT Panel Horizontal Timing Symbol t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 Parameter FPLINE start position Horizontal total period FPLINE width FPSHIFT period Data setup to FPSHIFT rising edge Data hold from FPSHIFT rising edge Horizontal display start position Horizontal display period FPLINE rising edge to GPIO3 rising edge GPIO3 pulse width GPIO1(GPIO0) pulse width GPIO1 rising edge (GPIO0 falling edge) to FPLINE rise edge GPIO2 toggle edge to FPLINE rise edge Min 400 1 1 0.5 0.5 60 320 59 1 353 5 11 Typ 14 Max 440 Units Ts (note 1) Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts Ts 1. 2. 3. 4. 5. 6. Ts t1typ t2typ t3typ t7typ t8typ = pixel clock period = (REG[2Ch] bits 9-0) + 1 = ((REG[20h] bits 6-0) + 1) x 8 = (REG[2Ch] bits 22-16) + 1 = ((REG[28h] bits 9-0) + 5) - ((REG[2Ch] bits 9-0) + 1) = ((REG[24h] bits 6-0) + 1) x 8 t1 t2 FPDAT[17:0] t4 FPFRAME (SPS) LINE1 LINE2 t3 LINE240 Figure 6-33: 320x240 Sharp `Direct' HR-TFT Panel Vertical Timing Table 6-30: 320x240 Sharp `Direct' HR-TFT Panel Vertical Timing Symbol t1 t2 t3 t4 Parameter Vertical total period Vertical display start position Vertical display period Vertical sync pulse width Min 245 Typ 4 240 2 Max 330 Units Lines Lines Lines Lines Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 82 Epson Research and Development Vancouver Design Center 6.5 USB Timing Data Signal Rise and Fall Time Figure 6-34 Data Signal Rise and Fall Time Figure 6-35 Differential Data Jitter Figure 6-36 Differential to EOP Transition Skew and EOP Width S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 83 Figure 6-37 Receiver Jitter Tolerance Table 6-31 USB Interface Timing Symbol USBFREQ TPERIOD TR TF TRFM VCRS ZDRV TDRATE TDDJ1 TDDJ2 TDEOP TEOPT TJR1 TJR2 TEOPR1 TEOPR2 Parameter USB Clock Frequency USB Clock Period CL = 50 pF Notes 1,2 (TR/ TF) Steady State Drive Figure 6-34 4 4 90 1.3 28Note 5 11.97 Figure 6-35 Figure 6-35 Figure 6-36 Figure 6-36 Figure 6-37 Figure 6-37 Figure 6-36 Figure 6-36 -3.5 -4.0 -2 160 -18.5 -9 40 80 12 0 0 0 167 0 0 Conditions Waveform Min Typ 48 1 -----------------------USBFREQ 20 20 110 2.0 44 12.03 3.5 4.0 5 175 18.5 9 % V Mbs ns ns ns ns ns ns ns ns ns Max Unit MHz Rise & Fall Times Rise/Fall time matching Output Signal Crossover Voltage Driver Output Resistance Data Rate Figure 6-34 Figure 6-34 Source Differential Driver Jitter to Notes 3,4. Next Transition Source Differential Driver Jitter for Notes 3,4 Paired Transitions Differential to EOP Transition Skew Source EOP Width Receiver Data Jitter Tolerance to Next Transition Note 4 Note 4 Note 4 Receiver Data Jitter Tolerance for Note 4 Paired Transitions EOP Width at Receiver; Must reject as EOP EOP Width at Receiver; Must accept as EOP Note 4 Note 4 1 2 3 4 5 Measured from 10% to 90% of the data signal. The rising and falling edges should be smoothly transitioning (monotonic). Timing difference between the differential data signals. Measured at crossover point of differential data signals. 20 is placed in series to meet this USB specification. The actual driver output impedance is 15 . S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Page 84 Epson Research and Development Vancouver Design Center 7 Clocks 7.1 Clock Descriptions 7.1.1 BCLK BCLK is an internal clock derived from CLKI. BCLK can be a divided version (/1, /2) of CLKI. CLKI is typically derived from the host CPU bus clock. The source clock options for BCLK may be selected as in the following table. Table 7-1: BCLK Clock Selection Source Clock Options CLKI CLKI / 2 BCLK Selection CNF6 = 0 CNF6 = 1 Note For synchronous bus interfaces, it is recommended that BCLK be set the same as the CPU bus clock (not a divided version of CLKI) e.g. SH-3, SH-4. 7.1.2 MCLK MCLK provides the internal clock required to access the embedded SRAM. The S1D13A04 is designed with efficient power saving control for clocks (clocks are turned off when not used); reducing the frequency of MCLK does not necessarily save more power. Furthermore, reducing the MCLK frequency relative to the BCLK frequency increases the CPU cycle latency and so reduces screen update performance. For a balance of power saving and performance, the MCLK should be configured to have a high enough frequency setting to provide sufficient screen refresh as well as acceptable CPU cycle latency. Note The maximum frequency of MCLK is 50MHz (30MHz if running CORE VDD at 2.0V 10%). As MCLK is derived from BCLK, when BCLK is greater than 50MHz, MCLK must be divided using REG[04h] bits 5-4. The Memory Controller Power Save Status bit (REG[14h] bit 6) must return a 1 before disabling the MCLK source. The source clock options for MCLK may be selected as in the following table. Table 7-2: MCLK Clock Selection Source Clock Options BCLK BCLK / 2 BCLK / 3 BCLK / 4 MCLK Selection REG[04h] bits 5-4 = 00 REG[04h] bits 5-4 = 01 REG[04h] bits 5-4 = 10 REG[04h] bits 5-4 = 11 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 85 7.1.3 PCLK PCLK is the internal clock used to control the panel. It should be chosen to match the optimum frame rate of the panel. See Section 10, "Frame Rate Calculation" on page 143 for details on the relationship between PCLK and frame rate. Some flexibility is possible in the selection of PCLK. Firstly, panels typically have a range of permissible frame rates. Secondly, it may be possible to choose a higher PCLK frequency and tailor the horizontal non-display period to bring down the frame-rate to its optimal value. The source clock options for PCLK may be selected as in the following table. Table 7-3: PCLK Clock Selection Source Clock Options MCLK MCLK /2 MCLK /3 MCLK /4 MCLK /8 BCLK BCLK /2 BCLK /3 BCLK /4 BCLK /8 CLKI CLKI /2 CLKI /3 CLKI /4 CLKI /8 CLKI2 CLKI2 /2 CLKI2 /3 CLKI2 /4 CLKI2 /8 PCLK Selection REG[08h] bits 7-0 = 00h REG[08h] bits 7-0 = 10h REG[08h] bits 7-0 = 20h REG[08h] bits 7-0 = 30h REG[08h] bits 7-0 = 40h REG[08h] bits 7-0 = 01h REG[08h] bits 7-0 = 11h REG[08h] bits 7-0 = 21h REG[08h] bits 7-0 = 31h REG[08h] bits 7-0 = 41h REG[08h] bits 7-0 = 02h REG[08h] bits 7-0 = 12h REG[08h] bits 7-0 = 22h REG[08h] bits 7-0 = 32h REG[08h] bits 7-0 = 42h REG[08h] bits 7-0 = 03h REG[08h] bits 7-0 = 13h REG[08h] bits 7-0 = 23h RREG[08h] bits 7-0 = 33h REG[08h] bits 7-0 = 43h Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 86 Epson Research and Development Vancouver Design Center There is a relationship between the frequency of MCLK and PCLK that must be maintained. Table 7-4: Relationship between MCLK and PCLK SwivelView Orientation Color Depth (bpp) 16 8 SwivelView 0 and 180 4 2 1 SwivelView 90 and 270 16/8/4/2/1 MCLK to PCLK Relationship fMCLK fPCLK fMCLK fPCLK / 2 fMCLK fPCLK / 4 fMCLK fPCLK / 8 fMCLK fPCLK /16 fMCLK 1.25fPCLK 7.1.4 PWMCLK PWMCLK is the internal clock used by the Pulse Width Modulator for output to the panel. The source clock options for PWMCLK may be selected as in the following table. Table 7-5: PWMCLK Clock Selection Source Clock Options CLKI CLKI2 MCLK PCLK PWMCLK Selection REG[70h] bits 2-1 = 00 REG[70h] bits 2-1 = 01 REG[70h] bits 2-1 = 10 REG[70h] bits 2-1 = 11 For further information on controlling PWMCLK, see "PWM Clock Configuration Register" on page 114.. 7.1.5 USBCLK CLKUSB is an internal clock derived from USBCLK and should be fixed at 48MHz. USBCLK must be active to access the USB Registers. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 87 7.2 Clock Selection The following diagram provides a logical representation of the S1D13A04 internal clocks. USBCLK CLKUSB CLKI /2 0 1 BCLK CNF61 REG[04h] bits 5-4 00 /2 /3 /4 01 MCLK 10 11 00 01 000 10 CLKI2 11 /2 /3 /4 /8 00 01 10 11 REG[08h] bits 6-4 PWMCLK 001 010 011 1xx PCLK REG[08h] bits 1,0 REG[70h] bits 2-1 Figure 7-1: Clock Selection Note 1 CNF6 must be set at RESET#. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 88 Epson Research and Development Vancouver Design Center 7.3 Clocks versus Functions Table 7-6: "S1D13A04 Internal Clock Requirements", lists the internal clocks required for the following S1D13A04 functions. Table 7-6: S1D13A04 Internal Clock Requirements Function Register Read/Write Memory Read/Write Look-Up Table Register Read/Write Software Power Save LCD Output USB Register Read/Write Bus Clock (BCLK) Required Required Required Required Required Required Memory Clock (MCLK) Not Required Required Required Not Required Required Not Required Pixel Clock (PCLK) Not Required Not Required Not Required Not Required Required Not Required PWM Clock (PWMCLK) Not Required1 Not Required1 Not Required1 Not Required1 Not Required 1 1 USB Clock (USBCLK) Not Required Not Required Not Required Not Required Not Required Required Not Required Note 1 PWMCLK is an optional clock (see Section 7.1.4, "PWMCLK" on page 86). S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 89 8 Registers This section discusses how and where to access the S1D13A04 registers. It also provides detailed information about the layout and usage of each register. 8.1 Register Mapping The S1D13A04 registers are memory-mapped. When the system decodes the input pins as CS# = 0 and M/R# = 0, the registers may be accessed. The register space is decoded by AB[16:0] and is mapped as follows. Table 8-1: S1D13A04 Register Mapping M/R# 1 0 0 0 0 Address 00000h to 28000h 0000h to 0088h 4000h to 4054h 8000h to 8019h 10000h to 1FFFEh Size 160K bytes 136 bytes 84 bytes 25 bytes 65536 bytes (64K bytes) Function SRAM memory Configuration registers USB registers 2D Acceleration Registers 2D Accelerator Data Port 8.2 Register Set The S1D13A04 register set is as follows. Table 8-2: S1D13A04 Register Set Register Pg LCD Register Descriptions (Offset = 0h) Read-Only Configuration Registers REG[00h] Product Information Register 91 Register Pg Clock Configuration Registers REG[04h] Memory Clock Configuration Register 92 REG[08h] Pixel Clock Configuration Register 92 Panel Configuration Registers REG[0Ch] Panel Type & MOD Rate Register REG[14h] Power Save Configuration Register 93 96 REG[10h] Display Settings Register 94 Look-Up Table Registers REG[18h] Look-Up Table Write Register 98 REG[1Ch] Look-Up Table Read Register 99 Display Mode Registers REG[20h] Horizontal Total Register REG[28h] Horizontal Display Period Start Position Register REG[30h] Vertical Total Register REG[38h] Vertical Display Period Start Position Register REG[40h] Main Window Display Start Address Register 100 101 102 103 104 REG[24h] Horizontal Display Period Register REG[2Ch] FPLINE Register REG[34h] Vertical Display Period Register REG[3Ch] FPFRAME Register REG[44h] Main Window Line Address Offset Register 100 101 102 103 104 Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 90 Epson Research and Development Vancouver Design Center Table 8-2: S1D13A04 Register Set Register REG[50h] PIP+ + Pg Picture-in-Picture Plus (PIP ) Registers + Register REG[54h] PIP+ Window Line Address Offset Register REG[5Ch] PIP+ Window Y Positions Register Pg 105 108 Window Display Start Address Register 105 106 REG[58h] PIP Window X Positions Register Miscellaneous Registers REG[60h] Special Purpose Register REG[70h] PWM Clock Configuration Register REG[80h] Scratch Pad A Register REG[88h] Scratch Pad C Register 110 114 116 116 REG[64h] GPIO Status and Control Register REG[74h] PWMOUT Duty Cycle Register REG[84h] Scratch Pad B Register 112 115 116 USB Register Descriptions (Offset = 4000h) REG[4000h] Control Register REG[4004h] Interrupt Status Register 0 REG[4008h] Interrupt Status Register 1 REG[4012h] Endpoint 1 Receive Mailbox Data Register REG[401Ah] Endpoint 2 Transmit Mailbox Data Register REG[4020h] Endpoint 3 Receive FIFO Data Register REG[4024h] Endpoint 3 Receive FIFO Status Register REG[4028h] Endpoint 4 Transmit FIFO Data Register REG[402Ch] Endpoint 4 Transmit FIFO Status Register REG[4030h] Endpoint 4 Maximum Packet Size Register REG[4034h] Frame Counter MSB Register REG[4038h] Extended Register Index REG[403Ah], Index[00h] Vendor ID MSB REG[403Ah], Index[02h] Product ID MSB REG[403Ah], Index[04h] Release Number MSB REG[403Ah], Index[06h] Receive FIFO Almost Full Threshold REG[403Ah], Index[08h] USB Control REG[403Ah], Index[0Ah] Packet Control REG[403Ah], Index[0Ch] FIFO Control REG[4042h] Reserved REG[4046h] Interrupt Control Enable Register 0 REG[404Ah] Interrupt Control Status/Clear Register 0 REG[404Eh] Interrupt Control Masked Status Register 0 REG[4052h] USB Software Reset Register 117 119 120 121 122 122 123 123 124 124 126 126 126 127 127 127 128 128 129 130 131 132 134 134 REG[4002h] Interrupt Enable Register 0 REG[4006h] Interrupt Enable Register 1 REG[4010h] Endpoint 1 Index Register REG[4018h] Endpoint 2 Index Register REG[401Ch] Endpoint 2 Interrupt Polling Interval Register REG[4022h] Endpoint 3 Receive FIFO Count Register REG[4026h] Endpoint 3 Maximum Packet Size Register REG[402Ah] Endpoint 4 Transmit FIFO Count Register REG[402Eh] Endpoint 4 Maximum Packet Size Register REG[4032h] USB Status Register REG[4036h] Frame Counter LSB Register REG[403Ah] Extended Register Data REG[403Ah], Index[01h] Vendor ID LSB REG[403Ah], Index[03h] Product ID LSB REG[403Ah], Index[05h] Release Number LSB 118 120 121 121 122 122 123 124 124 125 126 126 126 127 127 REG[403Ah], Index[07h] Transmit FIFO Almost Empty Threshold 127 REG[403Ah], Index[09h] Maximum Power Consumption REG[403Ah], Index[0Bh] Reserved REG[4040h] USBFC Input Control Register REG[4044h] Pin Input Status / Pin Output Data Register REG[4048h] Interrupt Control Enable Register 1 REG[404Ch] Interrupt Control Status/Clear Register 1 REG[4050h] Interrupt Control Masked Status Register 1 REG[4054h] USB Wait State Register 128 129 130 131 131 133 134 134 2D Acceleration (BitBLT) Register Descriptions (Offset = 8000h) REG[8000h] BitBLT Control Register REG[8008h] BitBLT Command Register REG[8010h] BitBLT Destination Start Address Register REG[8018h] BitBLT Width Register REG[8020h] BitBLT Background Color Register 135 137 139 140 141 REG[8004h] BitBLT Status Register REG[800Ch] BitBLT Source Start Address Register REG[8014h] BitBLT Memory Address Offset Register REG[801Ch] BitBLT Height Register REG[8024h] BitBLT Foreground Color Register 136 139 140 140 141 2D Acceleration (BitBLT) Data Register Descriptions (Offset = 10000h) AB16-AB0 = 10000h-1FFFEh, 2D Accelerator (BitBLT) Data Memory Mapped Region Register 141 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 91 8.3 LCD Register Descriptions (Offset = 0h) Unless specified otherwise, all register bits are set to 0 during power-on. 8.3.1 Read-Only Configuration Registers Product Information Register REG[00h] Default = 2Cxx282Ch Product Code bits 5-0 31 30 29 28 27 26 Revision Code bits 1-0 25 24 n/a 23 22 21 20 CNF[6:0] Status 19 18 17 16 Revision Code bits 1-0 1 0 Read Only Display Buffer Size bits 7-0 15 14 13 12 11 10 9 8 7 6 Product Code bits 5-0 5 4 3 2 bits 31-26 bits 25-24 bits 22-16 Product Code These read-only bits indicate the product code. The product code is 001011 (0Bh). Revision Code These are read-only bits that indicates the revision code. The revision code is 00. CNF[6:0] Status These read-only status bits return the status of the configuration pins CNF[6:0]. CNF[6:0] are latched at the rising edge of RESET#. For a functional description of each configuration bit (CNF[6:0]), see Section 4.4, "Summary of Configuration Options" on page 30. Note CNF3 Status (bit 19) always reads back a 1. The CNF3 pin is reserved and must be set to 1. bits 15-8 Display Buffer Size Bits [7:0] This is a read-only register that indicates the size of the SRAM display buffer measured in 4K byte increments. The S1D13A04 display buffer is 160K bytes and therefore this register returns a value of 40 (28h). Value of this register = display buffer size / 4K bytes = 160K bytes / 4K bytes = 40 (28h) bits 7-2 bits 1-0 Product Code These read-only bits indicate the product code. The product code is 001011 (0Bh). Revision Code These are read-only bits that indicates the revision code. The revision code is 00. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 92 Epson Research and Development Vancouver Design Center 8.3.2 Clock Configuration Registers Memory Clock Configuration Register REG[04h] Default = 00000000h n/a 31 30 29 28 27 n/a 15 14 13 12 11 10 9 8 7 6 26 25 24 23 22 21 20 MCLK Divide Select bits 1-0 5 4 19 18 17 16 Read/Write Reserved 3 2 1 0 bits 5-4 MCLK Divide Select Bits [1:0] These bits determine the divide used to generate the Memory Clock (MCLK) from the Bus Clock (BCLK). Table 8-3: MCLK Divide Selection MCLK Divide Select Bits 00 01 10 11 BCLK to MCLK Frequency Ratio 1:1 2:1 3:1 4:1 bit 0 Reserved. This bit must be set to 0. Pixel Clock Configuration Register REG[08h] Default = 00000000h n/a 31 30 29 28 27 n/a 15 14 13 12 11 10 9 8 7 26 25 24 23 22 21 20 19 n/a 3 2 18 Read/Write 17 16 PCLK Source Select bits 1-0 1 0 PCLK Divide Select bits 2-0 6 5 4 bits 6-4 PCLK Divide Select Bits [1:0] These bits determine the divide used to generate the Pixel Clock (PCLK) from the Pixel Clock Source. Table 8-4: PCLK Divide Selection PCLK Divide Select Bits 000 001 010 011 100 101 - 111 PCLK Source to PCLK Frequency Ratio 1:1 2:1 3:1 4:1 8:1 Reserved S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 93 bits 1-0 PCLK Source Select Bits [1:0] These bits determine the source of the Pixel Clock (PCLK). Table 8-5: PCLK Source Selection PCLK Source Select Bits 00 01 10 11 PCLK Source MCLK BCLK CLKI CLKI2 8.3.3 Panel Configuration Registers Panel Type & MOD Rate Register REG[0Ch] Default = 00000000h n/a 31 30 29 28 n/a 27 26 25 24 23 Panel Data Format Select 7 22 Color/ Mono Panel Select 6 21 20 MOD Rate bits 5-0 19 `Direct' HR-TFT Res Select 3 18 n/a 17 16 Read/Write Panel Data Width bits 1-0 5 4 Panel Type bits 1-0 1 0 15 14 13 12 11 10 9 8 2 bits 21-16 MOD Rate Bits [5:0] These bits are for passive LCD panels only. When these bits are all 0, the MOD output signal (DRDY) toggles every FPFRAME. For a non-zero value n, the MOD output signal (DRDY) toggles every n FPLINE. Panel Data Format Select When this bit = 0, 8-bit single color passive LCD panel data format 1 is selected. For AC timing see Section 6.4.5, "Single Color 8-Bit Panel Timing (Format 1)" on page 66. When this bit = 1, 8-bit single color passive LCD panel data format 2 is selected. For AC timing see Section 6.4.6, "Single Color 8-Bit Panel Timing (Format 2)" on page 68. Color/Mono Panel Select When this bit = 0, a monochrome LCD panel is selected. When this bit = 1, a color LCD panel is selected. Panel Data Width Bits [1:0] These bits select the data width size of the LCD panel. Table 8-6: Panel Data Width Selection Panel Data Width Bits [1:0] 00 01 10 11 Passive Panel Data Width Size 4-bit 8-bit 16-bit Reserved Active Panel Data Width Size 9-bit 12-bit 18-bit Reserved bit 7 bit 6 bits 5-4 Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 94 Epson Research and Development Vancouver Design Center bit 3 `Direct' HR-TFT Resolution Select This bit selects one of two panel resolutions when the `Direct' HR-TFT interface is selected. This bit has no effect for other panel types. Table 8-7: Active Panel Resolution Selection `Direct' HR-TFT Resolution Select Bit 0 1 HR-TFT Resolution 160x160 320x240 bits 1-0 Panel Type Bits[1:0] These bits select the panel type. Table 8-8: LCD Panel Type Selection Panel Type Bits [1:0] 00 01 10 11 Panel Type STN TFT `Direct' HR-TFT Reserved Display Settings Register REG[10h] Default = 00000000h Pixel n/a Vertical 31 30 29 28 27 26 n/a 15 14 13 12 11 10 9 8 7 6 5 4 25 Pixel Display Blank 23 Dithering Disable 22 n/a Horiz. 24 21 Doubling Doubling SW Video Invert 20 PIP Window Enable + Read/Write n/a SwivelView Mode Select 16 19 18 17 Bits-per-pixel Select (actual value: 1, 2, 4, 8 or 16 bpp) 3 2 1 0 bit 25 Pixel Doubling Vertical Enable This bit controls the pixel doubling feature for the vertical dimension or height of the panel (i.e. 160 pixel high data doubled to 320 pixel high panel). When this bit = 1, pixel doubling in the vertical dimension (height) is enabled. When this bit = 0, there is no hardware effect. Note Pixel Doubling is not designed to support color depths of 1 bit-per-pixel or SwivelView 90 / 270 modes. bit 24 Pixel Doubling Horizontal Enable This bit controls the pixel doubling feature for the horizontal dimension or width of the panel (i.e. 160 pixel wide data doubled to 320 pixel wide panel) When this bit = 1, pixel doubling in the horizontal dimension (width) is enabled. When this bit = 0, there is no hardware effect. Note Pixel Doubling is not designed to support color depths of 1 bit-per-pixel or SwivelView 90 / 270 modes. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 95 bit 23 Display Blank When this bit = 0, the LCD display pipeline is enabled. When this bit = 1, the LCD display pipeline is disabled and all LCD data outputs are forced to zero (i.e., the screen is blanked). Dithering Disable When this bit = 0, dithering on the passive LCD panel is enabled, allowing a maximum of 64K colors (218) or 64 gray shades in 1/2/4/8 bpp mode. In 16bpp mode, only 64K colors (216) can also be achieved. When this bit = 1, dithering on the passive LCD panel is disabled, allowing a maximum of 4096 colors (212) or 16 gray shades. The dithering algorithm provides more shades of each primary color. Note bit 22 For a summary of the results of dithering for each color depth, see Table 8-10: "LCD Bit-per-pixel Selection," on page 96. bit 20 Software Video Invert When this bit = 0, video data is normal. When this bit = 1, video data is inverted. Note Video data is inverted after the Look-Up Table bit 19 PIP+ Window Enable This bit enables a PIP+ window within the main window. The location of the PIP+ window within the landscape window is determined by the PIP+ X Position register (REG[58h]) and PIP+ Y Position register (REG[5Ch]). The PIP+ window has its own Display Start Address register (REG[50h]) and Memory Address Offset register (REG[54h]). The PIP+ window shares the same color depth and SwivelViewTM orientation as the main window. When this bit = 1, the PIP+ window is enabled. When this bit = 0, the PIP+ window is disabled. SwivelView Mode Select Bits [1:0] These bits select different SwivelViewTM orientations: Table 8-9: SwivelViewTM Mode Select Options SwivelView Mode Select Bits 00 01 10 11 SwivelView Orientation 0 (Normal) 90 180 270 bit 17-16 Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 96 Epson Research and Development Vancouver Design Center bits 4-0 Bit-per-pixel Select Bits [4:0] These bits select the color depth (bit-per-pixel) for the displayed data for both the main window and the PIP+ window (if active). 1, 2, 4 and 8 bpp modes use the 18-bit LUT, allowing maximum 64K colors. 16 bpp mode bypasses the LUT, allowing only 64K colors. Table 8-10: LCD Bit-per-pixel Selection Maximum Number of Colors/Shades Bit-per-pixel Color Depth (bpp) Select Bits [4:0] 00000 00001 00010 00011 00100 00101 - 00111 01000 10000 10001 - 11111 8 bpp 16 bpp 64K/64 64K/64 Reserved 4 bpp 64K/64 Reserved 64K/64 64K/64 256/64 64K/64 1 bpp 2 bpp 64K/64 64K/64 Reserved 64K/64 16/16 Passive Panel (Dithering On) TFT Panel Max. No. Of Simultaneously Displayed Colors/Shades 2/2 4/4 Reserved 64K/64 64K/64 Power Save Configuration Register REG[14h] Default = 00000010h n/a 31 30 29 28 27 26 25 24 23 VNDP Status (RO) 11 10 9 8 7 22 Memory Power Save Status (RO) 6 21 20 Power Save Enable 4 3 19 18 Read/Write 17 16 `Direct' HR-TFT GPO Control 1 0 n/a n/a n/a 15 14 13 12 5 2 bit 7 Vertical Non-Display Period Status (Read-only) This is a read-only status bit. When this bit = 0, the LCD panel output is in a Vertical Display Period. When this bit = 1, the LCD panel output is in a Vertical Non-Display Period. Memory Controller Power Save Status (Read-only) This read-only status bit indicates the power save state of the memory controller and must be checked before turning off the MCLK source clock. When this bit = 0, the memory controller is powered up. When this bit = 1, the memory controller is powered down and the MCLK source can be turned off. Note bit 6 Memory writes are possible during power save mode because the S1D13A04 dynamically enables the memory controller for display buffer writes. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 97 bit 4 Power Save Mode Enable When this bit = 1, the software initiated power save mode is enabled. When this bit = 0, the software initiated power save mode is disabled. At reset, this bit is set to 1. For a summary of Power Save Mode, see Section 15, "Power Save Mode" on page 159. Note Memory writes are possible during power save mode because the S1D13A04 dynamically enables the memory controller for display buffer writes. Power Considerations: The S1D13A04 may experience higher than normal Quiescent Current immediately after applying power. To prevent this condition, the following start up sequence must be followed: 1. Power-up/Reset the S1D13A04. 2. Initialize all registers. 3. Disable power save mode (set REG[14h] bit 4 to 0) Note By default, Power Save Mode is enabled (equal to 1) after power-up/Reset. If it is desirable/necessary to remain in power save mode for any length of time after power-up/Reset, the above described condition can be prevented by performing a R/W access to the embedded memory. bit 0 `Direct' HR-TFT LCD Interface GPO Control This bit is for HR-TFT panels only. For all other panel types, this bit has no effect. When the `direct' HR-TFT LCD interface is selected (REG[0Ch] bits 1-0 = 10), the DRDY pin becomes a general purpose output (GPO). This GPO can be used to control the HR-TFT MOD signal. When this bit = 0, DRDY (GPO) is forced low. When this bit = 1, DRDY (GPO) is forced high. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 98 Epson Research and Development Vancouver Design Center 8.3.4 Look-Up Table Registers Look-Up Table Write Register REG[18h] Default = 00000000h LUT Write Address 31 15 30 14 29 28 LUT Green Write Data 13 12 27 11 26 10 25 n/a 9 8 7 6 24 23 22 LUT Red Write Data 21 20 LUT Blue Write Data 5 4 19 3 18 2 17 n/a 1 0 Write Only n/a 16 Note The S1D13A04 has three 256-position, 6-bit wide LUTs, one for each of red, green, and blue (see Section 12, "Look-Up Table Architecture" on page 145). Note This is a write-only register and returns 00h if read. bits 31-24 LUT Write Address Bits [7:0] These bits form a pointer into the Look-Up Table (LUT) which is used to write the LUT Red, Green, and Blue data. When the S1D13A04 is set to a host bus interface using little endian (CNF4 = 0), the RGB data is updated to the LUT with the completion of a write to these bits. Note When a value is written to the LUT Write Address Bits, the same value is automatically placed in the LUT Read Address Bits (REG[1Ch] bits 31-24). bits 23-18 LUT Red Write Data Bits [5:0] These bits contains the data to be written to the red component of the Look-Up Table. The LUT position is controlled by the LUT Write Address bits (bits 31-24). LUT Green Write Data Bits [5:0] These bits contains the data to be written to the green component of the Look-Up Table. The LUT position is controlled by the LUT Write Address bits (bits 31-24). LUT Blue Write Data Bits [5:0] These bits contains the data to be written to the blue component of the Look-Up Table. The LUT position is controlled by the LUT Write Address bits (bits 31-24). When the S1D13A04 is set to a host bus interface using big endian (CNF4 = 1), the RGB data is updated to the LUT with the completion of a write to these bits. bits 15-10 bits 7-2 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 99 Look-Up Table Read Register REG[1Ch] Default = 00000000h LUT Read Address (write only) 31 15 30 14 29 28 LUT Green Read Data 13 12 27 11 26 10 25 n/a 9 8 7 6 24 23 22 Write Only (bits 31-24)/Read Only LUT Red Read Data 21 20 LUT Blue Read Data 5 4 19 3 18 2 17 n/a 1 0 n/a 16 Note The S1D13A04 has three 256-position, 6-bit wide LUTs, one for each of red, green, and blue (see Section 12, "Look-Up Table Architecture" on page 145). bits 31-24 LUT Read Address Bits [7:0] (Write Only) This register forms a pointer into the Look-Up Table (LUT) which is used to read LUT data. Red data is read from bits 23-18, green data from bits 15-10, and blue data from bits 7-2. Note If a write to the LUT Write Address Bits (REG[18h] bits 31-24) is made, the LUT Read Address bits are automatically updated with the same value. bits 23-18 LUT Red Read Data Bits [5:0] (Read Only) These bits point to the data from the red component of the Look-Up Table. The LUT position is controlled by the LUT Read Address bits (bits 31-24). This is a read-only register. LUT Green Read Data Bits [5:0] (Read Only) These bits point to the data from the green component of the Look-Up Table. The LUT position is controlled by the LUT Read Address bits (bits 31-24). This is a read-only register. LUT Blue Read Data Bits [5:0] (Read Only) These bits point to the data from the blue component of the Look-Up Table. The LUT position is controlled by the LUT Read Address bits (bits 31-24). This is a read-only register. bits 15-10 bits 7-2 Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 100 Epson Research and Development Vancouver Design Center 8.3.5 Display Mode Registers Horizontal Total Register REG[20h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 n/a 11 26 10 25 9 24 8 23 7 22 6 21 5 20 19 18 Horizontal Total bits 6-0 4 3 2 17 1 16 0 Read/Write bits 6-0 Horizontal Total Bits [6:0] These bits specify the LCD panel Horizontal Total period, in 8 pixel resolution. The Horizontal Total is the sum of the Horizontal Display period and the Horizontal Non-Display period. Since the maximum Horizontal Total is 1024 pixels, the maximum panel resolution supported is 800x600. REG[20h] bits 6:0 = (Horizontal Total in number of pixels / 8) - 1 Note 1 For all panels this register must be programmed such that: HDPS + HDP < HT HT - HDP 8MCLK 2 For passive panels, this register must be programmed such that: HPS + HPW < HT 3 See Section 6.4, "Display Interface" on page 56. Horizontal Display Period Register REG[24h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 n/a 11 26 10 25 9 24 8 23 7 22 6 21 5 20 19 18 Horizontal Display Period bits 6-0 4 3 2 17 1 16 0 Read/Write bits 6-0 Horizontal Display Period Bits [6:0] These bits specify the LCD panel Horizontal Display period, in 8 pixel resolution. The Horizontal Display period should be less than the Horizontal Total to allow for a sufficient Horizontal Non-Display period. REG[24h] bits 6:0 = (Horizontal Display Period in number of pixels / 8) - 1 Note For passive panels, HDP must be a minimum of 32 pixels and must be increased by multiples of 16. For TFT panels, HDP must be a minimum of 8 pixels and must be increased by multiples of 8. Note See Section 6.4, "Display Interface" on page 56. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 101 Horizontal Display Period Start Position Register REG[28h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 28 27 26 25 24 23 22 21 20 19 18 Horizontal Display Period Start Position bits 9-0 6 5 4 3 2 Read/Write 17 1 16 0 bits 9-0 Horizontal Display Period Start Position Bits [9:0] These bits specify a value used in the calculation of the Horizontal Display Period Start Position (in 1 pixel resolution) for TFT and `direct' HR-TFT panels. For passive LCD panels these bits must be set to 00h which will result in HDPS = 22. HDPS = (REG[28h] bits 9-0) + 22 For TFT panels, HDPS is calculated using the following formula. HDPS = (REG[28h] bits 9-0) + 5 Note This register must be programmed such that the following formula is valid. HDPS + HDP < HT FPLINE Register REG[2Ch] Default = 00000000h n/a FPLINE Polarity 27 11 26 10 25 9 24 8 23 7 FPLINE Pulse Width bits 6-0 22 21 20 19 FPLINE Pulse Start Position bits 9-0 6 5 4 3 18 2 Read/Write 31 15 30 14 29 n/a 13 28 12 17 1 16 0 bit 23 FPLINE Pulse Polarity This bit selects the polarity of the horizontal sync signal. For passive panels, this bit must be set to 1. For TFT panels, this bit is set according to the horizontal sync signal of the panel (typically FPLINE or LP). When this bit = 0, the horizontal sync signal is active low. When this bit = 1, the horizontal sync signal is active high. FPLINE Pulse Width Bits [6:0] These bits specify the width of the panel horizontal sync signal, in 1 pixel resolution. The horizontal sync signal is typically FPLINE or LP, depending on the panel type. REG[2Ch] bits 22-16 = FPLINE Pulse Width in number of pixels - 1 Note bits 22-16 For passive panels, these bits must be programmed such that the following formula is valid. HPW + HPS < HT Note See Section 6.4, "Display Interface" on page 56. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 102 Epson Research and Development Vancouver Design Center bits 9-0 FPLINE Pulse Start Position Bits [9:0] These bits specify the start position of the horizontal sync signal, in 1 pixel resolution. FPLINE Pulse Start Position in pixels = (REG[2Ch] bits 9-0) + 1 Note For passive panels, these bits must be programmed such that the following formula is valid. HPW + HPS < HT Note See Section 6.4, "Display Interface" on page 56. Vertical Total Register REG[30h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 6 28 27 26 25 24 23 22 21 20 Vertical Total bits 9-0 5 4 19 3 18 2 Read/Write 17 1 16 0 bits 9-0 Vertical Total Bits [9:0] These bits specify the LCD panel Vertical Total period, in 1 line resolution. The Vertical Total is the sum of the Vertical Display Period and the Vertical Non-Display Period. The maximum Vertical Total is 1024 lines. REG[30h] bits 9:0 = Vertical Total in number of lines - 1 Note 1 This register must be programmed such that the following formula is valid. VDPS + VDP < VT 2 See Section 6.4, "Display Interface" on page 56. Vertical Display Period Register REG[34h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 28 27 26 25 24 23 22 21 20 19 Vertical Display Period bits 9-0 6 5 4 3 18 2 Read/Write 17 1 16 0 bits 9-0 Vertical Display Period Bits [9:0] These bits specify the LCD panel Vertical Display period, in 1 line resolution. The Vertical Display period should be less than the Vertical Total to allow for a sufficient Vertical Non-Display period. REG[34h] bits 9:0 = Vertical Display Period in number of lines - 1 Note 1This register must be programmed such that the following formula is valid. VDPS + VDP < VT 2 See Section 6.4, "Display Interface" on page 56. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 103 Vertical Display Period Start Position Register REG[38h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 28 27 26 25 24 23 22 21 20 19 18 Vertical Display Period Start Position bits 9-0 6 5 4 3 2 Read/Write 17 1 16 0 bits 9-0 Vertical Display Period Start Position Bits [9:0] These bits specify the Vertical Display Period Start Position for panels in 1 line resolution. For passive LCD panels these bits must be set to 00h. For TFT panels, VDPS is calculated using the following formula. VDPS = REG[38h] bits 9-0 Note 1 This register must be programmed such that the following formula is valid. VDPS + VDP < VT 2See Section 6.4, "Display Interface" on page 56. FPFRAME Register REG[3Ch] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 28 27 26 25 24 FPFRAME Polarity 23 n/a 22 21 20 19 FPFRAME Pulse Start Position bits 9-0 6 5 4 3 Read/Write FPFRAME Pulse Width bits 2-0 18 2 17 1 16 0 bit 23 FPFRAME Pulse Polarity This bit selects the polarity of the vertical sync signal. For passive panels, this bit must be set to 1. For TFT panels, this bit is set according to the horizontal sync signal of the panel (typically FPFRAME, SPS or DY). When this bit = 0, the vertical sync signal is active low. When this bit = 1, the vertical sync signal is active high. FPFRAME Pulse Width Bits [2:0] These bits specify the width of the panel vertical sync signal, in 1 line resolution. The vertical sync signal is typically FPFRAME, SPS or DY, depending on the panel type. REG[3Ch] bits 18-16 = FPFRAME Pulse Width in number of lines - 1 Note bits 18-16 See Section 6.4, "Display Interface" on page 56. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 104 Epson Research and Development Vancouver Design Center bits 9-0 FPFRAME Pulse Start Position Bits [9:0] These bits specify the start position of the vertical sync signal, in 1 line resolution. For passive panels, these bits must be set to 00h. For TFT panels, VDPS is calculated using the following formula. VPS = REG[3Ch] bits 9-0 Note See Section 6.4, "Display Interface" on page 56. Main Window Display Start Address Register REG[40h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 10 25 24 23 22 21 Main Window Display Start Address bits 15-0 9 8 7 6 5 20 4 19 3 18 2 Read/Write bit 16 17 1 16 0 bits 16-0 Main Window Display Start Address Bits [16:0] This register specifies the starting address, in DWORDS, for the LCD image in the display buffer for the main window. Note that this is a double-word (32-bit) address. An entry of 00000h into these registers represents the first double-word of display memory, an entry of 00001h represents the second double-word of the display memory, and so on. Calculate the Display Start Address as follows: REG[40h] bits 16:0 = image address / 4 (valid only for SwivelView 0) Note For information on setting this register for other SwivelView orientations, see Section 13, "SwivelViewTM" on page 151. Main Window Line Address Offset Register REG[44h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 28 27 26 25 24 23 22 21 20 19 Main Window Line Address Offset bits 9-0 6 5 4 3 18 2 Read/Write 17 1 16 0 bits 9-0 Main Window Line Address Offset Bits [9:0] This register specifies the offset, in DWORDS, from the beginning of one display line to the beginning of the next display line in the main window. Note that this is a 32-bit address increment. Calculate the Line Address Offset as follows: REG[44h] bits 9:0 = display width in pixels / (32 / bpp) Note A virtual display can be created by programming this register with a value greater than the formula requires. When a virtual display is created the image width is larger than the display width and the displayed image becomes a window into the larger virtual image. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 105 8.3.6 Picture-in-Picture Plus (PIP+) Registers PIP+ Display Start Address Register REG[50h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 10 25 24 23 22 PIP+ Display Start Address bits 15-0 9 8 7 6 21 5 20 4 19 3 18 2 17 1 Read/Write bit 16 16 0 bits 16-0 PIP+ Display Start Address Bits [16:0] These bits form the 17-bit address for the starting double-word of the PIP+ window. Note that this is a double-word (32-bit) address. An entry of 00000h into these registers represents the first double-word of display memory, an entry of 00001h represents the second double-word of the display memory, and so on. Note These bits have no effect unless the PIP+ Window Enable bit is set to 1 (REG[10h] bit 19). PIP+ Line Address Offset Register REG[54h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 28 27 26 25 24 23 22 21 20 19 PIP+ Line Address Offset bits 9-0 6 5 4 3 18 2 17 1 16 0 Read/Write bits 9-0 PIP+ Window Line Address Offset Bits [9:0] These bits are the LCD display's 10-bit address offset from the starting double-word of line "n" to the starting double-word of line "n + 1" for the PIP+window. Note that this is a 32-bit address increment. Note These bits have no effect unless the PIP+ Window Enable bit is set to 1 (REG[10h] bit 19). Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 106 Epson Research and Development Vancouver Design Center PIP+ X Positions Register REG[58h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 28 27 26 25 24 23 PIP+ X End Position bits 9-0 22 21 20 19 PIP+ X Start Position bits 9-0 6 5 4 3 18 2 Read/Write 17 1 16 0 Note The effect of REG[58h] through REG[5Ch] takes place only after REG[5Ch] is written and at the next vertical non-display period. bits 25-16 PIP+ Window X End Position Bits [9:0] These bits determine the X end position of the PIP+ window in relation to the origin of the panel. Due to the S1D13A04 SwivelView feature, the X end position may not be a horizontal position value (only true in 0 and 180 SwivelView). For further information on defining the value of the X End Position register, see Section 14, "Picture-in-Picture Plus (PIP+)" on page 156. The register is also incremented differently based on the SwivelView orientation. For 0 and 180 SwivelView the X end position is incremented by x pixels where x is relative to the current color depth. Table 8-11: 32-bit Address Increments for Color Depth Color Depth 1 bpp 2 bpp 4 bpp 8 bpp 16 bpp Pixel Increment (x) 32 16 8 4 2 For 90 and 270 SwivelView the X end position is incremented in 1 line increments. Depending on the color depth, some of the higher bits in this register are unused because the maximum horizontal display width is 1024 pixels. Note These bits have no effect unless the PIP+ Window Enable bit is set to 1 (REG[10h] bit 19). S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 107 bits 9-0 PIP+ Window X Start Position Bits [9:0] These bits determine the X start position of the PIP+ window in relation to the origin of the panel. Due to the S1D13A04 SwivelView feature, the X start position may not be a horizontal position value (only true in 0 and 180 SwivelView). For further information on defining the value of the X Start Position register, see Section 14, "Picture-in-Picture Plus (PIP+)" on page 156. The register is also incremented differently based on the SwivelView orientation. For 0 and 180 SwivelView the X start position is incremented by x pixels where x is relative to the current color depth. Table 8-12: 32-bit Address Increments for Color Depth Color Depth 1 bpp 2 bpp 4 bpp 8 bpp 16 bpp Pixel Increment (x) 32 16 8 4 2 For 90 and 270 SwivelView the X start position is incremented in 1 line increments. Depending on the color depth, some of the higher bits in this register are unused because the maximum horizontal display width is 1024 pixels. Note These bits have no effect unless the PIP+ Window Enable bit is set to 1 (REG[10h] bit 19). Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 108 Epson Research and Development Vancouver Design Center PIP+ Y Positions Register REG[5Ch] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 28 27 26 25 24 23 PIP+ Y End Position bits 9-0 22 21 20 19 PIP+ Y Start Position bits 9-0 6 5 4 3 18 2 Read/Write 17 1 16 0 Note 1 The effect of REG[58h] through REG[5Ch] takes place only after REG[5Ch] is written and at the next vertical non-display period. 2 For host bus interfaces using little endian (CNF4 = 0), a write to bits 31-24 causes the PIP+ Window Y End Position to take effect. For host bus interfaces using big endian (CNF4 = 1), a write to bits 7-0 causes the PIP+ Window Y End Position to take effect. bits 25-16 PIP+ Window Y End Position Bits [9:0] These bits determine the Y end position of the PIP+ window in relation to the origin of the panel. Due to the S1D13A04 SwivelView feature, the Y end position may not be a vertical position value (only true in 0 and 180 SwivelView). For further information on defining the value of the Y End Position register, see Section 14, "Picture-in-Picture Plus (PIP+)" on page 156. The register is also incremented differently based on the SwivelView orientation. For 0 and 180 SwivelView the Y end position is incremented in 1 line increments. For 90 and 270 SwivelView the Y end position is incremented by y pixels where y is relative to the current color depth. Table 8-13: 32-bit Address Increments for Color Depth Color Depth 1 bpp 2 bpp 4 bpp 8 bpp 16 bpp Pixel Increment (y) 32 16 8 4 2 Depending on the color depth, some of the higher bits in this register are unused because the maximum vertical display height is 1024 pixels. Note These bits have no effect unless the PIP+ Window Enable bit is set to 1 (REG[10h] bit 19). S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 109 bits 9-0 PIP+ Window Y Start Position Bits [9:0] These bits determine the Y start position of the PIP+ window in relation to the origin of the panel. Due to the S1D13A04 SwivelView feature, the Y start position may not be a vertical position value (only true in 0 and 180 SwivelView). For further information on defining the value of the Y Start Position register, see Section 14, "Picture-in-Picture Plus (PIP+)" on page 156. The register is also incremented differently based on the SwivelView orientation. For 0 and 180 SwivelView the Y start position is incremented in 1 line increments. For 90 and 270 SwivelView the Y start position is incremented by y pixels where y is relative to the current color depth. Table 8-14: 32-bit Address Increments for Color Depth Color Depth 1 bpp 2 bpp 4 bpp 8 bpp 16 bpp Pixel Increment (y) 32 16 8 4 2 Depending on the color depth, some of the higher bits in this register are unused because the maximum vertical display height is 1024 pixels. Note These bits have no effect unless the PIP+ Window Enable bit is set to 1 (REG[10h] bit 19). Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 110 Epson Research and Development Vancouver Design Center 8.3.7 Miscellaneous Registers Special Purpose Register REG[60h] Default = 00000000h n/a 31 30 29 28 n/a 27 26 25 24 23 Reserved 22 Display Data Word Swap 6 21 Display Data Byte Swap 5 20 n/a 19 18 Latch Byte Select 3 2 1 Read/Write 17 n/a 16 2D Byte Swap 11 10 9 8 7 15 14 13 12 4 0 bits 23-16 bit 7 Reserved. These bits must be set to 0. 2D Byte Swap This bit enables the word data sent to/read from the 2D BitBLT port to be swapped (byte 0 and byte 1 are swapped). Note This bit is only used when the S1D13A04 is configured for Big Endian (CNF4 = 1 at RESET#). If configured for Little Endian (CNF4 = 0), this bit has no effect. bit 6 Display Data Word Swap The display pipe fetches 32-bits of data from the display buffer. This bit enables the lower 16-bit word and the upper 16-bit word to be swapped before sending them to the LCD display. If the Display Data Byte Swap bit is also enabled, then the byte order of the fetched 32-bit data is reversed. Note This bit is only used when the S1D13A04 is configured for Big Endian (CNF4 = 1 at RESET#). If configured for Little Endian (CNF4 = 0), this bit has no effect. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 111 bit 5 Display Data Byte Swap The display pipe fetches 32-bit of data from the display buffer. This bit enables byte 0 and byte 1 to be swapped, and byte 2 and byte 3 to be swapped, before sending them to the LCD display. If the Display Data Word Swap bit is also enabled, then the byte order of the fetched 32-bit data is reversed. Note This bit is only used when the S1D13A04 is configured for Big Endian (CNF4 = 1 at RESET#). If configured for Little Endian (CNF4 = 0), this bit has no effect. byte 0 32-bit display data from display buffer byte 1 Data byte 2 byte 3 Byte Swap Word Swap Serialization To LUT Figure 8-1: Display Data Byte/Word Swap bit 2 Latch Byte Select When this bit = 1, REG[5Ch] is latched in reverse order. When this bit = 0, there is no hardware effect. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 112 Epson Research and Development Vancouver Design Center GPIO Status and Control Register REG[64h] Default = 20000000h GPIO7 Input Enable 31 GPIO6 Input Enable 30 GPIO5 Input Enable 29 GPIO4 Input Enable 28 n/a 15 14 13 12 11 10 9 8 GPIO3 Input Enable 27 GPIO2 Input Enable 26 GPIO1 Input Enable 25 GPIO0 Input Enable 24 GPIO7 Config 23 GPIO7 Status 7 GPIO6 Config 22 GPIO6 Status 6 GPIO5 Config 21 GPIO5 Status 5 GPIO4 Config 20 GPIO4 Status 4 GPIO3 Config 19 GPIO3 Status 3 GPIO2 Config 18 GPIO2 Status 2 Read/Write GPIO1 Config 17 GPIO1 Status 1 GPIO0 Config 16 GPIO0 Status 0 Note The GPIO pins default as inputs after power-up and must be configured using the bits in this register. Note For information on GPIO pin mapping when the `direct' HR-TFT LCD interface is selected, see Table 4-9: "LCD Interface Pin Mapping," on page 32. bits 31-24 GPIO[7:0] Pin Input Enable bits These bits are used to enable the input function of each GPIO pin. They must be changed to a 1 after power-on reset to enable the input function of the corresponding GPIO pin (default is 0). Note The default for GPIO5 Pin Input Enable is 1. bits 23-16 GPIO[7:0] Pin IO Configuration When this bit = 0 (default), the corresponding GPIO pin is configured as an input pin. When this bit = 1, the corresponding GPIO pin is configured as an output pin. Note The input function of each GPIO pin must be enabled using the GPIO[7:0] Pin Input Enable bits (bits 31-24) before the input configuration takes effect. bit 7 GPIO7 Pin IO Status When GPIO7 is configured as an output, writing a 1 to this bit drives GPIO7 high and writing a 0 to this bit drives GPIO7 low. When GPIO7 is configured as an input, a read from this bit returns the status of GPIO7. GPIO6 Pin IO Status When GPIO6 is configured as an output, writing a 1 to this bit drives GPIO6 high and writing a 0 to this bit drives GPIO6 low. When GPIO6 is configured as an input, a read from this bit returns the status of GPIO6. GPIO5 Pin IO Status When GPIO5 is configured as an output, writing a 1 to this bit drives GPIO5 high and writing a 0 to this bit drives GPIO5 low. When GPIO5 is configured as an input, a read from this bit returns the status of GPIO5. bit 6 bit 5 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 113 bit 4 GPIO4 Pin IO Status When GPIO4 is configured as an output, writing a 1 to this bit drives GPIO4 high and writing a 0 to this bit drives GPIO4 low. When GPIO4 is configured as an input, a read from this bit returns the status of GPIO4. GPIO3 Pin IO Status When the `Direct' HR-TFT LCD interface is not selected (REG[0Ch] bits 1:0) and GPIO3 is configured as an output, writing a 1 to this bit drives GPIO3 high and writing a 0 to this bit drives GPIO3 low. When the `Direct' HR-TFT LCD interface is not selected (REG[0Ch] bits 1:0) and GPIO3 is configured as an input, a read from this bit returns the status of GPIO3. When the `Direct' HR-TFT LCD interface is enabled (REG[0Ch] bits 1:0 = 10), GPIO0 outputs the SPL signal automatically and writing to this bit has no effect. bit 3 bit 2 GPIO2 Pin IO Status When the `Direct' HR-TFT LCD interface is not selected (REG[0Ch] bits 1:0) and GPIO2 is configured as an output, writing a 1 to this bit drives GPIO2 high and writing a 0 to this bit drives GPIO2 low. When the `Direct' HR-TFT LCD interface is not selected (REG[0Ch] bits 1:0) and GPIO2 is configured as an input, a read from this bit returns the status of GPIO2. When the `Direct' HR-TFT LCD interface is enabled (REG[0Ch] bits 1:0 = 10), GPIO0 outputs the REV signal automatically and writing to this bit has no effect. bit 1 GPIO1 Pin IO Status When the `Direct' HR-TFT LCD interface is not selected (REG[0Ch] bits 1:0) and GPIO1 is configured as an output, writing a 1 to this bit drives GPIO1 high and writing a 0 to this bit drives GPIO1 low. When the `Direct' HR-TFT LCD interface is not selected (REG[0Ch] bits 1:0) and GPIO1 is configured as an input, a read from this bit returns the status of GPIO1. When the `Direct' HR-TFT LCD interface is enabled (REG[0Ch] bits 1:0 = 10), GPIO0 outputs the CLS signal automatically and writing to this bit has no effect. bit 0 GPIO0 Pin IO Status When the `Direct' HR-TFT LCD interface is not selected (REG[0Ch] bits 1:0) and GPIO0 is configured as an output, writing a 1 to this bit drives GPIO0 high and writing a 0 to this bit drives GPIO0 low. When the `Direct' HR-TFT LCD interface is not selected (REG[0Ch] bits 1:0) and GPIO0 is configured as an input, a read from this bit returns the status of GPIO0. When the `Direct' HR-TFT LCD interface is enabled (REG[0Ch] bits 1:0 = 10), GPIO0 outputs the PS signal automatically and writing to this bit has no effect. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 114 Epson Research and Development Vancouver Design Center PWM Clock Configuration Register REG[70h] Default = 00000000h n/a 31 30 29 28 n/a 27 26 25 24 23 22 21 20 19 PWM Clock Force High 3 18 Read/Write 17 16 PWM Clock Enable 0 PWM Clock Divide Select bits 3-0 11 10 9 8 7 6 5 4 PWMCLK Source Select bits 1-0 2 1 15 14 13 12 PWM Clock Enable PWM Clock Divider Clock Source / 2m Divided Clock PWM Duty Cycle Modulation Duty = n / 256 n = PWM Clock Duty Cycle PWMCLK to PWMOUT frequency = Clock Source / (2m X 256) m = PWM Clock Divide Select value PWM Clock Force High Figure 8-2: PWM Clock Block Diagram Note For further information on PWMCLK, see Section 7.1.4, "PWMCLK" on page 86. bits 7-4 PWM Clock Divide Select Bits [3:0] The value of these bits represents the power of 2 by which the selected PWM clock source is divided. Table 8-15: PWM Clock Divide Select Options PWM Clock Divide Select Bits [3:0] 0h 1h 2h 3h 4h 5h 6h 7h 8h 9h Ah Bh Ch Dh Eh Fh PWM Clock Divide Amount 1 2 4 8 16 32 64 128 256 512 1024 2048 4096 8192 16384 32768 Note This divided clock is further divided by 256 before it is output at PWMOUT. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 115 bit 3 PWM Clock Force High When this bit = 0, the PWMOUT pin function is controlled by the PWM Clock enable bit. When this bit = 1, the PWMOUT pin is forced to high. PWMCLK Source Select Bits [1:0] These bits determine the source of PWMCLK. Table 8-16: PWMCLK Source Selection PWMCLK Source Select Bits 00 01 10 11 PWMCLK Source CLKI CLKI2 BCLK PCLK bit 1 Note For further information on the PWMCLK source select, see Section 7.2, "Clock Selection" on page 87. bit 0 PWM Clock Enable When this bit = 0, PWMOUT output acts as a general purpose output pin controllable by bit 3 of REG[70h]. When this bit = 1, the PWM Clock circuitry is enabled. Note The PWM Clock circuitry is disabled when Power Save Mode is enabled. PWMOUT Duty Cycle Register REG[74h] Default = 00000000h n/a 31 15 30 14 29 13 28 n/a 12 11 10 9 8 7 6 27 26 25 24 23 22 21 20 19 18 PWMOUT Duty Cycle bits 7-0 5 4 3 2 Read/Write 17 1 16 0 bits 7-0 PWMOUT Duty Cycle Bits [7:0] This register determines the duty cycle of the PWMOUT output. Table 8-17: PWMOUT Duty Cycle Select Options PWMOUT Duty Cycle [7:0] 00h 01h 02h ... FFh PWMOUT Duty Cycle Always Low High for 1 out of 256 clock periods High for 2 out of 256 clock periods ... High for 255 out of 256 clock periods Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 116 Epson Research and Development Vancouver Design Center Scratch Pad A Register REG[80h] Default = not applicable Scratch Pad A bits 31-24 31 15 30 14 29 13 28 12 27 11 26 10 25 9 24 23 Scratch Pad A bits 15-0 8 7 22 6 21 5 20 4 19 3 18 2 Read/Write 17 1 16 0 bits 31-0 Scratch Pad A Bits [31:0] This register contains general purpose read/write bits. These bits have no effect on hardware. Note The contents of the Scratch Pad A register defaults to an un-defined state after initial power-up. Any data written to this register remains intact when the S1D13A04 is reset, as long as the chip is not powered off. Scratch Pad B Register REG[84h] Default = not applicable Scratch Pad B bits 31-24 31 15 30 14 29 13 28 12 27 11 26 10 25 9 24 23 Scratch Pad B bits 15-0 8 7 22 6 21 5 20 4 19 3 18 2 Read/Write 17 1 16 0 bits 31-0 Scratch Pad B Bits [31:0] This register contains general purpose read/write bits. These bits have no effect on hardware. Note The contents of the Scratch Pad B register defaults to an un-defined state after initial power-up. Any data written to this register remains intact when the S1D13A04 is reset, as long as the chip is not powered off. Scratch Pad C Register REG[88h] Default = not applicable Scratch Pad C bits 31-24 31 15 30 14 29 13 28 12 27 11 26 10 25 9 24 23 22 Scratch Pad C bits 15-0 8 7 6 21 5 20 4 19 3 18 2 Read/Write 17 1 16 0 bits 31-0 Scratch Pad C Bits [31:0] This register contains general purpose read/write bits. These bits have no effect on hardware. Note The contents of the Scratch Pad C register defaults to an un-defined state after initial power-up. Any data written to this register remains intact when the S1D13A04 is reset, as long as the chip is not powered off. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 117 8.4 USB Registers (Offset = 4000h) The S1D13A04 USB device occupies a 48 byte local register space which can be accessed by the CPU on the local host interface. To access the USB registers: 1. A valid USBCLK must be provided. 2. The USBClk Enable bit (REG[4000h] bit 7) must be set to 1 and the USB Setup bit (REG[4000h] bit 2) must be set to 1. Both bits should be set together. If any of the above conditions are not true, the USB registers must not be accessed. Control Register REG[4000h] 15 USBClk Enable 7 Default = 00h n/a 13 USB Enable 5 12 Endpoint 4 Stall 4 11 Endpoint 3 Stall 3 10 USB Setup 2 9 Reserved 1 Read/Write 8 Reserved 0 14 Software EOT 6 bit 7 USBClk Enable. This bit allows the USBClk to be enabled/disabled allowing the S1D13A04 to save power when the USBClk is not required. This bit should be initially set with the USB Setup bit. However, it can be disabled/re-enabled individually. When this bit = 1, the USBClk is enabled. When this bit = 0, the USBClk is disabled. Note The USB Registers must not be accessed when this bit is 0. bit 6 Software EOT This bit determines the response to an IN request to Endpoint 4 when the transmit FIFO is empty. If this bit is asserted, the S1D13A04 responds to an IN request to Endpoint 4 with an ACK and a zero length packet if the FIFO is empty. If this bit is not asserted, the S1D13A04 responds to an IN request from Endpoint 4 with an NAK if the FIFO is empty, indicating that it expects to transmit more data. This bit is automatically cleared when the S1D13A04 responds to the host with a zero length packet when the FIFO is empty. USB Enable Any device or configuration descriptor reads from the host will be acknowledged with a NAK until this bit is set. This allows time for the local CPU to set up the interrupt polling register, maximum packet size registers, and other configuration registers (e.g. Product ID and Vendor ID) before the host reads the descriptors. Note bit 5 As the device and configuration descriptors cannot be read by the host until the USB Enable bit is set, the device enumeration process will not complete and the device will not be recognized on the USB. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 118 Epson Research and Development Vancouver Design Center bit 4 Endpoint 4 Stall. If this bit is set, host bulk reads from the transmit FIFO will result in a STALL acknowledge by the S1D13A04. No data will be returned to the USB host. Endpoint 3 Stall. If this bit is set, host bulk writes to the receive FIFO will result in a STALL acknowledge by the S1D13A04. Receive data will be discarded. USB Setup This bit is used by software to select between GPIO and USB functions for multifunction GPIO pins (GPIO[7:4]). This bit should be set at the same time as the USBClk Enable bit. When this bit = 1, the USB function is selected. When this bit = 0, the GPIO function is selected. Note bit 3 bit 2 The USB Registers must not be accessed when this bit is 0. bit 1 bit 0 Reserved. This bit must be set to 0. Reserved. This bit must be set to 0. Interrupt Enable Register 0 REG[4002h] Default = 00h n/a 15 Suspend Request Interrupt Enable 7 14 SOF Interrupt Enable 6 13 reserved 5 12 Endpoint 4 Interrupt Enable 4 11 Endpoint 3 Interrupt Enable 3 10 Endpoint 2 Interrupt Enable 2 9 Endpoint 1 Interrupt Enable 1 Read/Write 8 n/a 0 bit 7 Suspend Request Interrupt Enable. When set, this bit enables an interrupt to occur when the USB host is requesting the S1D13A04 USB device to enter suspend mode. SOF Interrupt Enable. When set, this bit enables an interrupt to occur when a start-of-frame packet is received by the S1D13A04. Reserved. This bit must be set to 0. Endpoint 4 Interrupt Enable. When set, this bit enables an interrupt to occur when a USB Endpoint 4 Data Packet has been sent by the S1D13A04. Endpoint 3 Interrupt Enable. When set, this bit enables an interrupt to occur when a USB Endpoint 3 Data Packet has been received by the S1D13A04. Endpoint 2 Interrupt Enable. When set, this bit enables an interrupt to occur when the USB Endpoint 2 Transmit Mailbox registers have been read by the USB host. bit 6 bit 5 bit 4 bit 3 bit 2 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 119 bit 1 Endpoint 1 Interrupt Enable. When set, this bit enables an interrupt to occur when the USB Endpoint 1 Receive Mailbox registers have been written to by the USB host. Interrupt Status Register 0 REG[4004h] Default = 00h n/a 15 Suspend Request Interrupt Status 7 14 SOF Interrupt Status 6 13 Reserved 5 12 Endpoint 4 Interrupt Status 4 11 Endpoint 3 Interrupt Status 3 10 Endpoint 2 Interrupt Status 2 9 Endpoint 1 Interrupt Status 1 Read/Write 8 Upper Interrupt Active (read only) 0 bit 7 Suspend Request Interrupt Status. This bit indicates when a suspend-request has been received by the S1D13A04. Writing a 1 clears this bit. SOF Interrupt Status. This bit indicates when a start-of-frame packet has been received by the S1D13A04. Writing a 1 clears this bit. Reserved. This bit must be set to 0. Endpoint 4 Interrupt Status. This bit indicates when a USB Endpoint 4 Data packet has been sent by the S1D13A04. Writing a 1 clears this bit. Endpoint 3 Interrupt Status (Receive FIFO Valid). This bit indicates when a USB Endpoint 3 Data packet has been received by the S1D13A04. No more packets to endpoint 3 will be accepted until this bit is cleared. Writing a 1 clears this bit. Endpoint 2 Interrupt Status. This bit indicates when the USB Endpoint 2 Mailbox registers have been read by the USB host. Writing a 1 clears this bit. Endpoint 1 Interrupt Status (Receive Mailbox Valid). This bit indicates when the USB Endpoint 1 Mailbox registers have been written to by the USB host. Writing a 1 clears this bit. Upper Interrupt Active (read only). At least one interrupt status bit is set in register REG[4008h]. bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 120 Epson Research and Development Vancouver Design Center Interrupt Enable Register 1 REG[4006h] Default = 00h n/a 15 14 13 n/a 7 6 5 4 3 2 12 11 10 9 Transmit FIFO Almost Empty Interrupt Enable 1 Read/Write 8 Receive FIFO Almost Full Interrupt Enable 0 bit 1 Transmit FIFO Almost Empty Interrupt Enable. When set, this bit enables an interrupt to be generated when the Transmit FIFO Almost Empty status bit is set. Note The Transmit FIFO Almost Empty threshold must be set greater than zero, as the FIFO count must drop below the threshold to cause an interrupt. bit 0 Receive FIFO Almost Full Interrupt Enable. When set, this bit enables an interrupt to be generated when the Receive FIFO Almost Full status bit is set. Note The Receive FIFO Almost Full threshold must be set less than 64, as the FIFO count must rise above the threshold to cause an interrupt. Interrupt Status Register 1 REG[4008h] Default = 00h n/a 15 14 13 n/a 7 6 5 4 3 2 12 11 10 9 Transmit FIFO Almost Empty Status 1 Read/Write 8 Receive FIFO Almost Full Status 0 bit 1 Transmit FIFO Almost Empty Status. This bit is set when the number of bytes in the Transmit FIFO is equal to the Transmit FIFO Almost Empty Threshold, and another byte is sent to the USB bus from the FIFO. Writing a 1 clears this bit. Receive FIFO Almost Full Status. This bit is set when the number of bytes in the Receive FIFO is equal to the Receive FIFO Almost Full Threshold, and another byte is received from the USB bus into the FIFO. Writing a 1 clears this bit. bit 0 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 121 Endpoint 1 Index Register REG[4010h] Default = 00h n/a 15 7 14 6 13 n/a 5 12 4 11 3 10 2 Read/Write 9 Endpoint 1 Index bits 2-0 (RO) 1 8 0 bits 2-0 Endpoint 1 Index Register Bits [2:0]. This register determines which Endpoint 1 Receive Mailbox is accessed when the Endpoint 1 Receive Mailbox Data register is read. This register is automatically incremented after the Endpoint 1 Receive Mailbox Data register is read. This index register wraps around to zero when it reaches the maximum count (7). Endpoint 1 Receive Mailbox Data Register REG[4012h] Default = 00h n/a 15 7 14 6 13 5 12 11 Endpoint 1 Receive Mailbox Data bits 7-0 4 3 10 2 9 1 Read Only 8 0 bits 7-0 Endpoint 1 Receive Mailbox Data Bits [7:0]. This register is used to read data from one of the receive mailbox registers. Data is returned from the register selected by the Endpoint 1 Index Register. The eight receive mailbox registers are written by a USB bulk transfer to endpoint 1, and can be used to pass messages from the USB host to the local CPU. The format and content of the messages are user defined. If enabled, USB writes to this register can generate an interrupt. Endpoint 2 Index Register REG[4018h] Default = 00h n/a 15 7 14 6 13 n/a 5 12 4 11 3 10 2 Read/Write 9 Endpoint 2 Index bits 2-0 1 8 0 bits 2-0 Endpoint 2 Index Register Bits [2:0]. This register determines which Endpoint 2 Transmit Mailbox is accessed when the Endpoint 2 Transmit Mailbox Data register is read or written. This register is automatically incremented after the Endpoint 2 Transmit Mailbox Data port is read or written. This index register wraps around to zero when it reaches the maximum count (7). Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 122 Epson Research and Development Vancouver Design Center Endpoint 2 Transmit Mailbox Data Register REG[401Ah] Default = 00h n/a 15 7 14 6 13 5 12 11 Endpoint 2 Transmit Mailbox Data bits 7-0 4 3 10 2 9 1 Read/Write 8 0 bits 7-0 Endpoint 2 Transmit Mailbox Data Bits [7:0]. This register is used to read or write one of the transmit mailbox registers. The register being accessed is selected by the Endpoint 2 Index register. The eight Transmit Mailbox registers are written by the local CPU and are read by a USB transfer from endpoint 2. The format and content of the messages are user defined. If enabled, USB reads from this register can generate an interrupt. Endpoint 2 Interrupt Polling Interval Register REG[401Ch] Default = FFh n/a 15 7 14 6 13 5 12 11 Interrupt Polling Interval bits 7-0 4 3 10 2 9 1 Read/Write 8 0 bits 7-0 Interrupt Polling Interval Bits [7:0]. This register specifies the Endpoint 2 interrupt polling interval in milliseconds. It can be read by the host through the endpoint 2 descriptor. Endpoint 3 Receive FIFO Data Register REG[4020h] Default = 00h n/a 15 7 14 6 13 5 12 11 Endpoint 3 Receive FIFO Data bits 7-0 4 3 10 2 9 1 Read Only 8 0 bits7-0 Endpoint 3 Receive FIFO Data Bits [7:0]. This register is used by the local CPU to read USB receive FIFO data. The FIFO data is written by the USB host using bulk or isochronous transfers to endpoint 3. Endpoint 3 Receive FIFO Count Register REG[4022h] Default = 00h n/a 15 7 14 6 13 5 12 11 Receive FIFO Count bits 7-0 4 3 10 2 9 1 Read Only 8 0 bits 7-0 Receive FIFO Count Bits [7:0]. This register returns the number of receive FIFO entries containing valid entries. Values range from 0 (empty) to 64 (full). S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 123 Endpoint 3 Receive FIFO Status Register REG[4024h] Default = 01h n/a 15 14 n/a 7 6 5 13 12 Receive FIFO Flush 4 11 Receive FIFO Overflow 3 10 Receive FIFO Underflow 2 9 Receive FIFO Full (read only) 1 Read/Write 8 Receive FIFO Empty (read only) 0 bit 4 Receive FIFO Flush Writing to this bit causes the receive FIFO to be flushed. Reading this bit always returns a 0. Receive FIFO Overflow If set, this bit indicates that an attempt was made by the USB host to write to the receive FIFO when the receive FIFO was full. Writing a 1 clears this bit. Receive FIFO Underflow If set, this bit indicates that an attempt was made to read the receive FIFO when the receive FIFO was empty. Writing a 1 clears this bit. Receive FIFO Full If set, this bit indicates that the receive FIFO is full. Receive FIFO Empty If set, this bit indicates that the receive FIFO is empty. bit 3 bit 2 bit 1 bit 0 Endpoint 3 Maximum Packet Size Register REG[4026h] Default = 08h n/a 15 7 14 6 13 5 12 11 Endpoint 3 Max Packet Size bits 7-0 4 3 10 2 9 1 Read/Write 8 0 bits 7-0 Endpoint 3 Max Packet Size Bits [7:0]. This register specifies the maximum packet size for endpoint 3 in units of 8 bytes (default = 64 bytes). It can be read by the host through the endpoint 3 descriptor. Endpoint 4 Transmit FIFO Data Register REG[4028h] Default = 00h n/a 15 7 14 6 13 5 12 11 Transmit FIFO Data bits 7-0 4 3 10 2 9 1 Write Only 8 0 bits 7-0 Transmit FIFO Data Bits [7:0]. This register is used by the local CPU to write data to the transmit FIFO. The FIFO data is read by the USB host using bulk or isochronous transfers from endpoint 4. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 124 Epson Research and Development Vancouver Design Center Endpoint 4 Transmit FIFO Count Register REG[402Ah] Default = 00h n/a 15 7 14 6 13 5 12 11 Transmit FIFO Count bits 7-0 4 3 10 2 9 1 Read Only 8 0 bits 7-0 Transmit FIFO Count Bits [7:0]. This register returns the number of transmit FIFO entries containing valid entries. Values range from 0 (empty) to 64 (full). Endpoint 4 Transmit FIFO Status Register REG[402Ch] Default = 01h n/a 15 n/a 7 6 14 13 Transmit FIFO Valid 5 12 Transmit FIFO Flush 4 11 Transmit FIFO Overflow 3 10 Reserved 2 9 Transmit FIFO Full (read only) 1 Read/Write 8 Transmit FIFO Empty (read only) 0 bit 5 Transmit FIFO Valid. If set, this bit allows the data in the Transmit FIFO to be read by the next read from the host. This bit is automatically cleared by a host read. This bit is only used if bit 0 in USB[403Ah] Index [0Ch] is set. Transmit FIFO Flush. Writing to this bit causes the transmit FIFO to be flushed. Reading this bit always returns a 0. Transmit FIFO Overflow. If set, this bit indicates that an attempt was made by the local CPU to write to the transmit FIFO when the transmit FIFO was full. Writing a 1 clears this bit. Reserved. Transmit FIFO Full (read only). If set, this bit indicates that the transmit FIFO is full. Transmit FIFO Empty (read only). If set, this bit indicates that the transmit FIFO is empty. bit 4 bit 3 bit 2 bit 1 bit 0 Endpoint 4 Maximum Packet Size Register REG[402Eh] Default = 08h n/a 15 7 14 6 13 5 12 11 Endpoint 4 Max Packet Size bits 7-0 4 3 10 2 9 1 Read/Write 8 0 bits 7-0 Endpoint 4 Max Packet Size Bits [7:0]. This register specifies the maximum packet size for endpoint 4 in units of 8 bytes (default = 64 bytes). It can be read by the host through the endpoint 4 descriptor. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 125 Revision Register REG[4030h] 15 7 14 6 Default = 01h n/a 13 5 12 11 Chip Revision bits 7-0 4 3 10 2 9 1 Read Only 8 0 bits 7-0 Chip Revision Bits [7:0]. This register returns current silicon revision number of the USB client. USB Status Register REG[4032h] Default = 00h n/a 15 Suspend Control 7 14 USB Endpoint 4 STALL 6 13 USB Endpoint 4 NAK 5 12 USB Endpoint 4 ACK 4 11 USB Endpoint 3 STALL 3 10 USB Endpoint 3 NAK 2 9 USB Endpoint 3 ACK 1 Read/Write 8 Endpoint 2 Valid 0 bit 7 Suspend Control. If set, this bit indicates that there is a pending suspend request. Writing a 1 clears this bit and causes the S1D13A04 USB device to enter suspended mode. USB Endpoint 4 STALL. The last USB IN token could not be serviced because the endpoint was stalled (REG[4000h] bit 4 set), and was acknowledged with a STALL. Writing a 1 clears this bit. USB Endpoint 4 NAK. The last USB packet transmitted (IN packet) encountered a FIFO underrun condition, and was acknowledged with a NAK. Writing a 1 clears this bit. USB Endpoint 4 ACK. The last USB packet transmitted (IN packet) was successfully acknowledged with an ACK from the USB host. Writing a 1 clears this bit. USB Endpoint 3 STALL. The last USB packet received (OUT packet) could not be accepted because the endpoint was stalled (REG[4000h] bit 3 set), and was acknowledged with a STALL. Writing a 1 clears this bit. USB Endpoint 3 NAK. The last USB packet received (OUT packet) could not be accepted, and was acknowledged with a NAK. Writing a 1 clears this bit. USB Endpoint 3 ACK. The last USB packet received (OUT packet) was successfully acknowledged with an ACK. Writing a 1 clears this bit. Endpoint 2 Valid. When this bit is set, the 8-byte endpoint 2 mailbox registers have been written by the local CPU, but not yet read by the USB host. The local CPU should not write into these registers while this bit is set. bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 126 Epson Research and Development Vancouver Design Center Frame Counter MSB Register REG[4034h] Default = 00h n/a 15 7 14 6 13 n/a 5 12 4 11 3 10 2 9 Frame Counter bits 10-8 1 Read Only 8 0 Frame Counter LSB Register REG[4036h] Default = 00h n/a 15 7 14 6 13 5 12 11 Frame Counter bits 7-0 4 3 10 2 9 1 Read Only 8 0 bits 10-0 Frame Counter Bits [10:0] This register contains the frame counter from the most recent start-of-frame packet. Extended Register Index REG[4038h] Default = 00h n/a 15 7 14 6 13 5 12 11 Extended Register Index bits 7-0 4 3 10 2 9 1 Read/Write 8 0 bits 7-0 Extended Register Index Bits [7:0] This register selects which extended data register is accessed when the REG[403Ah] is read or written. Extended Register Data REG[403Ah] Default = 04h n/a 15 7 14 6 13 5 12 11 Extended Data bits 7-0 4 3 10 2 9 1 Read/Write 8 0 bits 7-0 Extended Data Bits [7:0] This port provides access to one of the extended data registers. The index of the current register is held in REG[4038h]. Vendor ID MSB REG[403Ah], Index[00h] 7 6 Default = 04h Vendor ID bits 15-8 5 4 3 2 1 Read/Write 0 Vendor ID LSB REG[403Ah], Index[01h] 7 6 Default = B8h Vendor ID bits 7-0 5 4 3 2 1 Read/Write 0 bits 15-0 Vendor ID Bits [15:0] These registers determine the Vendor ID returned in a "Get Device Descriptor" request. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 127 Product ID MSB REG[403Ah], Index[02h] 7 6 Default = 88h Product ID bits 15-8 5 4 3 2 1 Read/Write 0 Product ID LSB REG[403Ah], Index[03h] 7 6 Default = 21h Product ID bits 7-0 5 4 3 2 1 Read/Write 0 bits 15-0 Product ID Bits [15:0] These registers determine the Product ID returned in a "Get Device Descriptor" request. Release Number MSB REG[403Ah], Index[04h] 7 6 Default = 01h Release Number bits 15-8 5 4 3 2 1 Read/Write 0 Release Number LSB REG[403Ah], Index[05h] 7 6 Default = 00h Release Number bits 7-0 5 4 3 2 1 Read/Write 0 bits 15-0 Release Number Bits [15:0] These registers determine the device release number returned in a "Get Device Descriptor" request. Receive FIFO Almost Full Threshold REG[403Ah], Index[06h] Default = 3Ch n/a 7 6 5 4 Receive FIFO Almost Full Threshold bits 5-0 3 2 1 Read/Write 0 bits 5-0 Receive FIFO Almost Full Threshold Bits [5:0] This register determines the threshold at which the receive FIFO almost full status bit is set. Note The Receive FIFO Almost Full threshold must be set less than 64, as the FIFO count must rise above the threshold to cause an interrupt. Transmit FIFO Almost Empty Threshold REG[403Ah], Index[07h] Default = 04h n/a 7 6 5 4 Transmit FIFO Almost Empty Threshold bits 5-0 3 2 1 Read/Write 0 bits 5-0 Transmit FIFO Almost Empty Threshold Bits [5:0]. This register determines the threshold at which the transmit FIFO almost empty status bit is set. Note The Transmit FIFO Almost Empty threshold must be set greater than zero, as the FIFO count must drop below the threshold to cause an interrupt. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 128 Epson Research and Development Vancouver Design Center USB Control REG[403Ah], Index[08h] Default = 01h n/a Read/Write USB String Enable 3 2 1 0 7 6 5 4 bit 0 USB String Enable. When set, this bit allows the default Vendor and Product ID String Descriptors to be returned to the host. When this bit is cleared, the string index values in the Device Descriptor are set to zero. Maximum Power Consumption REG[403Ah], Index[09h] Default = FAh Maximum Current bits 7-0 7 6 5 4 3 2 1 Read/Write 0 bits 7-0 Maximum Current Bits [7:0]. The amount of current drawn by the peripheral from the USB port in increments of 2 mA. The S1D13A04 reports this value to the host controller in the configuration descriptor. The default and maximum value is 500 mA (FAh * 2 mA). In order to comply with the USB specification the following formula must apply: REG[403Ah] index[09h] FAh. Packet Control REG[403Ah], Index[0Ah] EP4 Data Toggle 7 EP3 Data Toggle 6 Default = 00h EP2 Data Toggle 5 EP1 Data Toggle 4 Reserved 3 Reserved 2 n/a 1 Read/Write Reserved 0 bit 7 EP4 Data Toggle Bit. Contains the value of the Data Toggle bit to be sent in response to the next IN token to endpoint 4 from the USB host. Note When a write is made to this bit, the value cannot be read back before a minimum of 12 USBCLK. bit 6 EP3 Data Toggle Bit. Contains the value of the Data Toggle bit expected in the next DATA packet to endpoint 3 from the USB host. Note When a write is made to this bit, the value cannot be read back before a minimum of 12 USBCLK. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 129 bit 5 EP2 Data Toggle Bit. Contains the value of the Data Toggle bit to be sent in response to the next IN token to endpoint 2 from the USB host. Note When a write is made to this bit, the value cannot be read back before a minimum of 12 USBCLK. bit 4 EP1 Data Toggle Bit. Contains the value of the Data Toggle bit expected in the next DATA packet to endpoint 1 from the USB host. Note When a write is made to this bit, the value cannot be read back before a minimum of 12 USBCLK. bit 3 bit 2 bit 0 Reserved. This bit must be set to 0. Reserved. This bit must be set to 0. Reserved. This bit must be set to 0. Reserved REG[403Ah], Index[0Bh] 7 6 Default = 00h n/a 5 4 3 2 1 Read/Write Reserved 0 bit 0 Reserved. This bit must be set to 0. FIFO Control REG[403Ah], Index[0Ch] Default = 00h n/a Read/Write Transmit FIFO Valid Mode 3 2 1 0 7 6 5 4 bit 0 Transmit FIFO Valid Mode. When set, this bit causes a NAK response to a host read request from the transmit FIFO (EP4) unless the FIFO Valid bit (in register EP4STAT) is set. When this bit is cleared, any data waiting in the transmit FIFO will be sent in response to a host read request, and the FIFO Valid bit is ignored. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 130 Epson Research and Development Vancouver Design Center USBFC Input Control Register REG[4040h] Default = 0Dh n/a 15 n/a 7 14 USCMPEN 6 13 Reserved 5 12 Reserved 4 11 ISO 3 10 WAKEUP 2 9 Reserved 1 Read/Write 8 Reserved 0 These bits control inputs to the USB module. bit 6 USCMPEN This bit controls the USB differential input receiver. 0 = differential input receiver disabled 1 = differential input receiver enabled Reserved. This bit must be set to 0. Reserved. This bit must be set to 0. ISO This bits selects between isochronous and bulk transfer modes for the FIFOs (Endpoint 3 and Endpoint 4). 0 = Isochronous transfer mode 1 = Bulk transfer mode WAKEUP This active low bit initiates a USB remote wake-up. 0 = initiate USB remote wake-up 1 = no action Reserved. This bit must be set to 0. Reserved. This bit must be set to 0. bits 5 bits 4 bit 3 bit 2 bit 1 bit 0 Reserved REG[4042h] n/a 15 7 14 6 13 5 12 n/a 4 3 2 1 0 11 10 9 8 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 131 Pin Input Status / Pin Output Data Register REG[4044h] Default = depends on USB input pin state n/a 15 14 13 n/a 7 6 5 4 3 2 12 11 10 9 USBDETECT Input Pin Status (read only) 1 Read/Write 8 USBPUP Output Pin Status 0 These bits can generate interrupts. bit 1 USBDETECT Input Pin Status This read-only bit indicates the status of the USBDETECT input pin after a steady-state period of 0.5 seconds. USBPUP Output Pin Status This bit controls the state of the USBPUP output pin. This bit must be set to 1 to enable the USB interface and USB registers. See the S1D13A04 Programming Notes and Examples, document number X37-A-G-003-xx for further information on this bit. Interrupt Control Enable Register 0 REG[4046h] Default = 00h n/a 15 n/a 7 14 USB Host Connected 6 13 Reserved 5 12 Reserved 4 11 Reserved 3 10 Reserved 2 9 USBRESET 1 8 Reserved 0 bit 0 Read/Write These bits enable interrupts from the corresponding bit of the Interrupt Control Status/Clear Register 0. 0 = corresponding interrupt bit disabled (masked). 1 = corresponding interrupt bit enabled. Interrupt Control Enable Register 1 REG[4048h] Default = 00h n/a 15 n/a 7 14 USB Host Disconnect 6 13 Reserved 5 12 Device Configured 4 11 Reserved 3 10 Reserved 2 9 Reserved 1 8 INT 0 Read/Write These bits enable interrupts from the corresponding bit of the Interrupt Control Status/Clear Register 1. 0 = corresponding interrupt bit disabled (masked). 1 = corresponding interrupt bit enabled. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 132 Epson Research and Development Vancouver Design Center Interrupt Control Status/Clear Register 0 REG[404Ah] Default = 00h n/a 15 n/a 7 14 USB Host Connected 6 13 Reserved 5 12 Reserved 4 11 Reserved 3 10 Reserved 2 9 USBRESET 1 Read/Write 8 Reserved 0 On reads, these bits represent the interrupt status for interrupts caused by low-to-high transitions on the corresponding signals. 0 (read) = no low-to-high event detected on the corresponding signal. 1 (read) = low-to-high event detected on the corresponding signal. On writes, these bits clear the corresponding interrupt status bit. 0 (write) = corresponding interrupt status bit unchanged. 1 (write) = corresponding interrupt status bit cleared to zero. These bits must always be cleared via a write to this register before first use. This will ensure that any changes on input pins during system initialization do not generate erroneous interrupts. The interrupt bits are used as follows. bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 USB Host Connected Indicates the USB device is connected to a USB host. Reserved. Must be set to 0. Reserved. Must be set to 0. Reserved. Must be set to 0. Reserved. Must be set to 0. USBRESET Indicates the USB device is reset using the RESET# pin or using the USB port reset. Reserved. Must be set to 0. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 133 Interrupt Control Status/Clear Register 1 REG[404Ch] Default = 00h n/a 15 n/a 7 14 USB Host Disconnected 6 13 Reserved 5 12 Device Configured 4 11 Reserved 3 10 Reserved 2 9 Reserved 1 Read/Write 8 INT 0 On reads, these bits represent the interrupt status for interrupts caused by high-to-low transitions on the corresponding signals. 0 (read) = no high-to-low event detected on the corresponding signal. 1 (read) = high-to-low event detected on the corresponding signal. On writes, these bits clear the corresponding interrupt status bit. 0 (write) = corresponding interrupt status bit unchanged. 1 (write) = corresponding interrupt status bit cleared to zero. These bits must always be cleared via a write to this register before first use. This will ensure that any changes on input pins during system initialization do not generate erroneous interrupts. The interrupt bits are used as follows. bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 USB Host Disconnected Indicates the USB device is disconnected from a USB host. Reserved. Must be set to 0. Device Configured. Indicates the USB device has been configured by the USB host. Reserved. Must be set to 0. Reserved. Must be set to 0. Reserved. Must be set to 0. INT Indicates an interrupt request originating from within the USB registers (REG[4000h] to REG[403Ah]). Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 134 Epson Research and Development Vancouver Design Center Interrupt Control Masked Status Register 0 REG[404Eh] Default = 00h n/a 15 n/a 7 14 USB Host Connected 6 13 Reserved 5 12 Reserved 4 11 Reserved 3 10 Reserved 2 9 USBRESET 1 Read Only 8 Reserved 0 These read-only bits represent the logical AND of the corresponding Interrupt Control Status/Clear Register 0 (REG[404Ah])and the Interrupt Control Enable Register 0 (REG[4046h]). Interrupt Control Masked Status Register 1 REG[4050h] Default = 00h n/a 15 n/a 7 14 USB Host Disconnected 6 13 Reserved 5 12 Device Configured 4 11 Reserved 3 10 Reserved 2 9 Reserved 1 8 INT 0 Read Only These read-only bits represent the logical AND of the corresponding Interrupt Control Status/Clear Register 1 (REG[404Ch]) and the Interrupt Control Enable Register 1 (REG[4048h]). USB Software Reset Register REG[4052h] Default = 00h n/a 15 7 14 6 13 5 12 11 USB Software Reset (Code = 10100100) bits 7-0 4 3 10 2 9 1 8 0 Write Only bits 7-0 USB Software Reset Bits [7:0] (Write Only) When the specific code of 10100100b is written to these bits the USB module of the S1D13A04 is reset. Use of the above code avoids the possibility of accidently resetting the USB. USB Wait State Register REG[4054h] Default = 00h n/a 15 7 14 6 13 n/a 5 4 3 2 12 11 10 Read/Write 9 8 USB Wait State bits 1-0 1 0 bits 1-0 USB Wait State Bits [1:0] This register controls the number of wait states the S1D13A04 uses for its internal USB support. For all bus interfaces supported by the S1D13A04 these bits must be set to 01. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 135 8.5 2D Acceleration (BitBLT) Registers (Offset = 8000h) These registers control the S1D13A04 2D Acceleration engine. For detailed BitBLT programming instructions, see the S1D13A04 Programming Notes and Examples, document number X37A-G-003-xx. BitBLT Control Register REG[8000h] Default = 00000000h n/a 31 30 29 28 27 26 25 24 n/a 15 14 13 12 11 10 9 8 7 6 5 4 3 2 23 22 21 20 19 Color Format Select 18 Read/Write Dest Linear Select 17 Source Linear Select 16 BitBLT Enable (WO) 0 1 bit 18 BitBLT Color Format Select This bit selects the color format that the 2D operation is applied to. When this bit = 0, 8 bpp (256 color) format is selected. When this bit = 1, 16 bpp (64K color) format is selected. BitBLT Destination Linear Select When this bit = 1, the Destination BitBLT is stored as a contiguous linear block of memory. When this bit = 0, the Destination BitBLT is stored as a rectangular region of memory. The BitBLT Memory Address Offset register (REG[8014h]) determines the address offset from the start of one line to the next line. BitBLT Source Linear Select When this bit = 1, the Source BitBLT is stored as a contiguous linear block of memory. When this bit = 0, the Source BitBLT is stored as a rectangular region of memory. The BitBLT Memory Address Offset register (REG[8014h]) determines the address offset from the start of one line to the next line. BitBLT Enable This bit is write only. Setting this bit to 1 begins the 2D BitBLT operation. This bit must not be set to 0 while a BitBLT operation is in progress. Note bit 17 bit 16 bit 0 To determine the status of a BitBLT operation use the BitBLT Busy Status bit (REG[8004h] bit 0). Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 136 Epson Research and Development Vancouver Design Center BitBLT Status Register REG[8004h] Default = 00000000h n/a 31 30 29 28 Number of Used FIFO Entries 27 n/a 15 14 13 12 11 10 9 8 7 26 25 24 23 n/a 22 FIFO Not Empty 6 21 FIFO Half Full 5 20 FIFO Full Status 4 19 18 n/a 3 2 Read Only Number of Free FIFO Entries (0 means full) 17 16 BitBLT Busy Status 0 1 bits 28-24 Number of Used FIFO Entries Bits [4:0] These bits indicate the minimum number of FIFO entries currently in use (there may be more values in internal pipeline stages). Number of Free FIFO Entries Bits [4:0] These bits indicate the number of empty FIFO entries available. If these bits return a 0, the FIFO is full. BitBLT FIFO Not-Empty Status This is a read-only status bit. When this bit = 0, the BitBLT FIFO is empty. When this bit = 1, the BitBLT FiFO has at least one data. To reduce system memory read latency, software can monitor this bit prior to a BitBLT read burst operation. The following table shows the number of words available in BitBLT FIFO under different status conditions. Table 8-18: BitBLT FIFO Words Available BitBLT FIFO Not Number of Words BitBLT FIFO Half BitBLT FIFO Full available in BitBLT Empty Status Full Status Status FIFO (REG[8004h] Bit 4) (REG[8004h] Bit 5) (REG[8004h] Bit 6) 0 0 0 1 0 0 1 1 0 1 1 1 0 1 to 6 7 to 14 15 to 16 bits 20-16 bit 6 bit 5 BitBLT FIFO Half Full Status This is a read-only status bit. When this bit = 1, the BitBLT FIFO is half full or greater than half full. When this bit = 0, the BitBLT FIFO is less than half full. BitBLT FIFO Full Status This is a read-only status bit. When this bit = 1, the BitBLT FIFO is full. When this bit = 0, the BitBLT FIFO is not full. bit 4 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 137 bit 0 BitBLT Busy Status This bit is a read-only status bit. When this bit = 1, the BitBLT operation is in progress. When this bit = 0, the BitBLT operation is complete. Note During a BitBLT Read operation, the BitBLT engine does not attempt to keep the FIFO full. If the FIFO becomes full, the BitBLT operation stops temporarily as data is read out of the FIFO. The BitBLT will restart only when less than 14 values remain in the FIFO. BitBLT Command Register REG[8008h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 n/a 10 9 8 7 6 5 4 3 25 24 23 22 21 20 19 Read/Write BitBLT ROP Code bits 3-0 18 17 16 BitBLT Operation bits 3-0 2 1 0 bits 19-16 BitBLT Raster Operation Code/Color Expansion Bits [3:0] ROP Code for Write BitBLT and Move BitBLT. Bits 2-0 also specify the start bit position for Color Expansion. Table 8-19 : BitBLT ROP Code/Color Expansion Function Selection BitBLT ROP Code Bits [3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Boolean Function for Write BitBLT and Move BitBLT 0 (Blackness) ~S . ~D or ~(S + D) ~S . D ~S S . ~D ~D S^D ~S + ~D or ~(S . D) S.D ~(S ^ D) D ~S + D S S + ~D S+D 1 (Whiteness) Boolean Function for Pattern Fill 0 (Blackness) ~P . ~D or ~(P + D) ~P . D ~P P . ~D ~D P^D ~P + ~D or ~(P . D) P.D ~(P ^ D) D ~P + D P P + ~D P+D 1 (Whiteness) Start Bit Position for Color Expansion bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 Note S = Source, D = Destination, P = Pattern. ~ = NOT, . = Logical AND, + = Logical OR, ^ = Logical XOR Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 138 Epson Research and Development Vancouver Design Center bits 3-0 BitBLT Operation Bits [3:0] Specifies the 2D Operation to be carried out based on the following table. Table 8-20 : BitBLT Operation Selection BitBLT Operation Bits [3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 Other combinations Read BitBLT. Move BitBLT in positive direction with ROP. Move BitBLT in negative direction with ROP. Transparent Write BitBLT. Transparent Move BitBLT in positive direction. Pattern Fill with ROP. Pattern Fill with transparency. Color Expansion. Color Expansion with transparency. Move BitBLT with Color Expansion. Move BitBLT with Color Expansion and transparency. Solid Fill. Reserved BitBLT Operation Write BitBLT with ROP. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 139 BitBLT Source Start Address Register REG[800Ch] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 10 25 24 23 22 BitBLT Source Start Address bits 15-0 9 8 7 6 21 5 20 4 19 3 18 2 Read/Write BitBLT Source Start Address bits 20-16 17 1 16 0 bits 20-0 BitBLT Source Start Address Bits [20:0] A 21-bit register that specifies the source start address for the BitBLT operation. If data is sourced from the CPU, then bit 0 is used for byte alignment within a 16-bit word and the other address bits are ignored. In pattern fill operation, the BitBLT Source Start Address is defined by the following equation. Value programmed to the Source Start Address Register = Pattern Base Address + Pattern Line Offset + Pixel Offset. The following table shows how Source Start Address Register is defined for 8 and 16 bpp color depths. Table 8-21 : BitBLT Source Start Address Selection Color Format 8 bpp 16 bpp Pattern Base Address[20:0] BitBLT Source Start Address[20:6] BitBLT Source Start Address[20:7] Pattern Line Offset[2:0] BitBLT Source Start Address[5:3] BitBLT Source Start Address[6:4] Pixel Offset[3:0] BitBLT Source Start Address[2:0] BitBLT Source Start Address[3:0] Note For further information on the BitBLT Source Start Address register, see the S1D13A04 Programming Notes and Examples, document number X37A-G-003-xx. BitBLT Destination Start Address Register REG[8010h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 10 25 24 23 22 BitBLT Destination Start Address bits 15-0 9 8 7 6 21 5 20 4 19 3 18 2 Read/Write BitBLT Destination Start Address bits 20-16 17 1 16 0 bits 20-0 BitBLT Destination Start Address Bits [20:0] A 21-bit register that specifies the destination start address for the BitBLT operation. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 140 Epson Research and Development Vancouver Design Center BitBLT Memory Address Offset Register REG[8014h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 28 12 27 11 26 10 25 9 24 8 23 22 21 20 19 BitBLT Memory Address Offset bits 10-0 7 6 5 4 3 18 2 Read/Write 17 1 16 0 bits 10-0 BitBLT Memory Address Offset Bits [10:0] These bits are the display's 11-bit address offset from the starting word of line n to the starting word of line n + 1. They are used only for address calculation when the BitBLT is configured as a rectangular region of memory. They are not used for the displays. BitBLT Width Register REG[8018h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 6 28 27 26 25 24 23 22 21 20 BitBLT Width bits 9-0 5 4 19 3 18 2 Read/Write 17 1 16 0 bits 9-0 BitBLT Width Bits [9:0] A 10-bit register that specifies the BitBLT width in pixels - 1. BitBLT width in pixels = (ContentsOfThisRegister) + 1 BitBLT Height Register REG[801Ch] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 6 28 27 26 25 24 23 22 21 20 BitBLT Height bits 9-0 5 4 19 3 18 2 Read/Write 17 1 16 0 bits 9-0 BitBLT Height Bits [9:0] A 10-bit register that specifies the BitBLT height in lines - 1. BitBLT height in lines = (ContentsOfThisRegister) + 1 S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 141 BitBLT Background Color Register REG[8020h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 10 25 24 23 22 BitBLT Background Color bits 15-0 9 8 7 6 21 5 20 4 19 3 18 2 Read/Write 17 1 16 0 bits 15-0 BitBLT Background Color Bits [15:0] This register specifies the BitBLT background color for Color Expansion or key color for Transparent BitBLT. For 16 bpp color depths (REG[8000h] bit 18 = 1), bits 15-0 are used. For 8 bpp color depths (REG[8000h] bit 18 = 0), bits 7-0 are used. Note For Big Endian implementations, see the S1D13A04 Programming Notes and Examples, document number X37A-G-003-xx. BitBLT Foreground Color Register REG[8024h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 10 25 24 23 22 BitBLT Foreground Color bits 15-0 9 8 7 6 21 5 20 4 19 3 18 2 Read/Write 17 1 16 0 bits 15-0 BitBLT Foreground Color Bits [15:0] This register specifies the BitBLT foreground color for Color Expansion or Solid Fill. For 16 bpp color depths (REG[8000h] bit 18 = 1), bits 15-0 are used. For 8 bpp color depths (REG[8000h] bit 18 = 0), bits 7-0 are used. Note For Big Endian implementations, see the S1D13A04 Programming Notes and Examples, document number X37A-G-003-xx. 8.6 2D Accelerator (BitBLT) Data Register Descriptions The 2D Accelerator (BitBLT) data registers decode AB15-AB0 and require AB16 = 1. The BitBLT data registers are 32-bit wide. Byte access to the BitBLT data registers is not allowed. 2D Accelerator (BitBLT) Data Memory Mapped Region Register AB16-AB0 = 10000h-1FFFEh, even addresses BitBLT Data bits 31-16 31 15 30 14 29 13 28 12 27 11 26 10 25 9 24 23 BitBLT Data bits 15-0 8 7 22 6 21 5 20 4 19 3 18 2 17 1 16 0 Read/Write bits 15-0 BitBLT Data Bits [15:0] This register specifies the BitBLT data. This register is loosely decoded from 10000h to 1FFFEh. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 142 Epson Research and Development Vancouver Design Center 9 2D Accelerator (BitBLT) Engine 9.1 Overview The S1D13A04 is designed with a built-in 2D BitBLT engine which increases the performance of Bit Block Transfers (BitBLT). It supports 8 and 16 bit-per-pixel color depths. The BitBLT engine supports rectangular and linear addressing modes for source and destination in a positive direction for all BitBLT operations except the move BitBLT which also supports in a negative direction. The BitBLT operations support byte alignment of all types. The BitBLT engine has a dedicated BitBLT IO access space. This allows the BitBLT engine to support simultaneous BitBLT and host side operations. 9.2 BitBLT Operations The S1D13A04 2D BitBLT engine supports the following BitBLTs. For detailed information on using the individual BitBLT operations, refer to the S1D13A04 Programming Notes and Examples, document number X37A-G-003-xx. * Write BitBLT. * Move BitBLT. * Solid Fill BitBLT. * Pattern Fill BitBLT. * Transparent Write BitBLT. * Transparent Move BitBLT. * Read BitBLT. * Color Expansion BitBLT. * Move BitBLT with Color Expansion. Note For details on the BitBLT registers, see Section 8.5, "2D Acceleration (BitBLT) Registers (Offset = 8000h)" on page 135. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 143 10 Frame Rate Calculation The following formula is used to calculate the display frame rate. f PCLK FrameRate = ------------------------------( HT ) x ( VT ) Where: fPCLK HT = PClk frequency (Hz) = Horizontal Total = ((REG[20h] bits 6-0) + 1) x 8 Pixels = Vertical Total = ((REG[30h] bits 9-0) + 1) Lines VT Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 144 Epson Research and Development Vancouver Design Center 11 Display Data Formats The following diagrams show the display mode data formats for a little-endian system. 1 bpp: bit 7 Byte 0 Byte 1 Byte 2 Host Address Display Memory 2 bpp: bit 7 Byte 0 Byte 1 Byte 2 Host Address Display Memory 4 bpp: bit 7 Byte 0 Byte 1 Byte 2 Host Address Display Memory 8 bpp: bit 7 Byte 0 Byte 1 Byte 2 Host Address Display Memory 16 bpp: Byte 0 Byte 1 Byte 2 Byte 3 Host Address Panel Display A0 A1 A2 B0 B1 B2 C0 C1 C2 D0 D1 D2 E0 E1 E2 F0 F1 F2 G0 G1 G2 bit 0 H0 H1 H2 LUT Pn = RGB value from LUT Index (An, Bn, Cn, Dn, En, Fn, Gn, Hn) P0 P1 P2 P3 P4 P5 P6 P7 Panel Display A0 A2 A4 B0 B2 B4 C0 C2 C4 D0 D2 D4 A1 A3 A5 B1 B3 B5 C1 C3 C5 bit 0 D1 D3 D5 LUT Pn = RGB value from LUT Index (An, Bn, Cn, Dn) P0 P1 P2 P3 P4 P5 P6 P7 Panel Display A0 A4 A8 B0 B4 B8 A1 A5 A9 B1 B5 B9 A2 A6 B2 B6 A3 A7 bit 0 B3 B7 LUT Pn = RGB value from LUT Index (An, Bn) P0 P1 P2 P3 P4 P5 P6 P7 Panel Display A0 A8 A1 A9 A2 A3 A4 A5 A6 bit 0 A7 LUT Pn = RGB value from LUT Index (An) P0 P1 P2 P3 P4 P5 P6 P7 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A10 B10 A11 B11 5-6-5 RGB bit 7 bit 0 2 G1 0B4 G0 G0 B03 B02 B01 B00 0 0 R04 R03 R02 R01 R00 G05 G04 G03 G12 G11 G10 B14 B13 B12 B11 B10 R14 R13 R12 R11 R10 G15 G14 G13 P0 P1 P2 P3 P4 P5 P6 P7 Bypasses LUT Pn = (Rn4-0, Gn 5-0, Bn4-0) Panel Display Display Buffer Figure 11-1: 4/8/16 Bit-Per-Pixel Display Data Memory Organization Note 1. The Host-to-Display mapping shown here is for a little endian system. 2. For 16 bpp format, Rn, Gn, Bn represent the red, green, and blue color components. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 145 12 Look-Up Table Architecture The following figures are intended to show the display data output path only. Note When Video Data Invert is enabled the video data is inverted after the Look-Up Table. 12.1 Monochrome Modes The green Look-Up Table (LUT) is used for all monochrome modes. 1 Bit-per-pixel Monochrome Mode Green Look-Up Table 256x6 00 01 00 01 6-bit Gray Data FC FD FE FF 1 bit-per-pixel data from Display Buffer = unused Look-Up Table entries Figure 12-1: 1 Bit-per-pixel Monochrome Mode Data Output Path 2 Bit-per-pixel Monochrome Mode Green Look-Up Table 256x6 00 01 02 03 00 01 10 11 6-bit Gray Data FC FD FE FF 2 bit-per-pixel data from Display Buffer = unused Look-Up Table entries Figure 12-2: 2 Bit-per-pixel Monochrome Mode Data Output Path Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 146 Epson Research and Development Vancouver Design Center 4 Bit-per-pixel Monochrome Mode Green Look-Up Table 256x6 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 6-bit Gray Data FC FD FE FF 4 bit-per-pixel data from Display Buffer = unused Look-Up Table entries Figure 12-3: 4 Bit-per-pixel Monochrome Mode Data Output Path 8 Bit-per-pixel Monochrome Mode Green Look-Up Table 256x6 00 01 02 03 04 05 06 07 F8 F9 FA FB FC FD FE FF 0000 0000 0000 0001 0000 0010 0000 0011 0000 0100 0000 0101 0000 0110 0000 0111 6-bit Gray Data 1111 1000 1111 1001 1111 1010 1111 1011 1111 1100 1111 1101 1111 1110 1111 1111 8 bit-per-pixel data from Display Buffer Figure 12-4: 8 Bit-per-pixel Monochrome Mode Data Output Path S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 147 16 Bit-Per-Pixel Monochrome Mode The LUT is bypassed and the green data is directly mapped for this color depth- "Display Data Formats" on page 144.. 12.2 Color Modes 1 Bit-Per-Pixel Color Red Look-Up Table 256x6 00 01 0 1 6-bit Red Data FC FD FE FF Green Look-Up Table 256x6 00 01 0 1 6-bit Green Data FC FD FE FF Blue Look-Up Table 256x6 00 01 0 1 6-bit Blue Data FC FD FE FF 1 bit-per-pixel data from Image Buffer = unused Look-Up Table entries Figure 12-5: 1 Bit-Per-Pixel Color Mode Data Output Path Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 148 Epson Research and Development Vancouver Design Center 2 Bit-Per-Pixel Color Red Look-Up Table 256x6 00 01 02 03 00 01 10 11 6-bit Red Data FC FD FE FF Green Look-Up Table 256x6 00 01 02 03 00 01 10 11 6-bit Green Data FC FD FE FF Blue Look-Up Table 256x6 00 01 02 03 00 01 10 11 6-bit Blue Data FC FD FE FF 2 bit-per-pixel data from Image Buffer = unused Look-Up Table entries Figure 12-6: 2 Bit-Per-Pixel Color Mode Data Output Path S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 149 4 Bit-Per-Pixel Color Red Look-Up Table 256x6 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 6-bit Red Data FC FD FE FF Green Look-Up Table 256x6 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 6-bit Green Data FC FD FE FF Blue Look-Up Table 256x6 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 6-bit Blue Data FC FD FE FF 4 bit-per-pixel data from Image Buffer = unused Look-Up Table entries Figure 12-7: 4 Bit-Per-Pixel Color Mode Data Output Path Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 150 Epson Research and Development Vancouver Design Center 8 Bit-per-pixel Color Mode Red Look-Up Table 256x6 00 01 02 03 04 05 06 07 F8 F9 FA FB FC FD FE FF 0000 0000 0000 0001 0000 0010 0000 0011 0000 0100 0000 0101 0000 0110 0000 0111 6-bit Red Data 1111 1000 1111 1001 1111 1010 1111 1011 1111 1100 1111 1101 1111 1110 1111 1111 Green Look-Up Table 256x6 00 01 02 03 04 05 06 07 F8 F9 FA FB FC FD FE FF 0000 0000 0000 0001 0000 0010 0000 0011 0000 0100 0000 0101 0000 0110 0000 0111 6-bit Green Data 1111 1000 1111 1001 1111 1010 1111 1011 1111 1100 1111 1101 1111 1110 1111 1111 Blue Look-Up Table 256x6 00 01 02 03 04 05 06 07 F8 F9 FA FB FC FD FE FF 0000 0000 0000 0001 0000 0010 0000 0011 0000 0100 0000 0101 0000 0110 0000 0111 6-bit Blue Data 1111 1000 1111 1001 1111 1010 1111 1011 1111 1100 1111 1101 1111 1110 1111 1111 8 bit-per-pixel data from Display Buffer Figure 12-8: 8 Bit-per-pixel Color Mode Data Output Path 16 Bit-Per-Pixel Color Mode The LUT is bypassed and the color data is directly mapped for this color depth- "Display Data Formats" on page 144. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 151 13 SwivelViewTM 13.1 Concept Most computer displays are refreshed in landscape orientation - from left to right and top to bottom. Computer images are stored in the same manner. SwivelViewTM is designed to rotate the displayed image on an LCD by 90, 180, or 270 in a counter-clockwise direction. The rotation is done in hardware and is transparent to the user for all display buffer reads and writes. By processing the rotation in hardware, SwivelViewTM offers a performance advantage over software rotation of the displayed image. The image is not actually rotated in the display buffer since there is no address translation during CPU read/write. The image is rotated during display refresh. Note The Pixel Doubling feature of the S1D13A04 is not available in 90 and 270 SwivelView rotations. 13.2 90 SwivelViewTM 90 SwivelViewTM requires the Memory Clock (MCLK) to be at least 1.25 times the frequency of the Pixel Clock (PCLK), i.e. MCLK 1.25PCLK. The following figure shows how the programmer sees a 320x480 portrait image and how the image is being displayed. The application image is written to the S1D13A04 in the following sense: A-B-C-D. The display is refreshed by the S1D13A04 in the following sense: B-D-A-C. Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 152 Epson Research and Development Vancouver Design Center physical memory start address A B display start address (panel origin) D A SwivelView window C 320 480 image refreshed by S1D13A04 image seen by programmer = image in display buffer Figure 13-1: Relationship Between The Screen Image and the Image Refreshed in 90 SwivelView. 13.2.1 Register Programming Enable 90 SwivelViewTM Mode Set SwivelViewTM Mode Select bits (REG[10h] bits 17:16) to 01. Display Start Address The display refresh circuitry starts at pixel "B", therefore the Main Window Display Start Address register (REG[40h]) must be programmed with the address of pixel "B". To calculate the value of the address of pixel "B" use the following formula (assumes 8 bpp color depth). REG[40h] bits 16:0 = ((image address + (panel height x bpp / 8)) / 4) - 1 = ((0 + (320 pixels x 8 bpp / 8)) / 4) -1 = 79 (4Fh) Line Address Offset The Main Window Line Address Offset register (REG[44h]) is based on the display width and programmed using the following formula. REG[44h] bits 9:0 = display width in pixels / (32 / bpp) = 320 pixels / (32 / 8 bpp) = 80 (50h) S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 C 320 SwivelView window 480 D B Epson Research and Development Vancouver Design Center Page 153 13.3 180 SwivelViewTM The following figure shows how the programmer sees a 480x320 landscape image and how the image is being displayed. The application image is written to the S1D13A04 in the following sense: A-B-C-D. The display is refreshed by the S1D13A04 in the following sense: D-C-B-A. physical memory start address A SwivelView window C 480 image seen by programmer = image in display buffer D B 320 display start address (panel origin) 480 image refreshed by S1D13A04 Figure 13-2: Relationship Between The Screen Image and the Image Refreshed in 180 SwivelView. 13.3.1 Register Programming Enable 180 SwivelViewTM Mode Set SwivelViewTM Mode Select bits (REG[10h] bits 17:16) to 10. Display Start Address The display refresh circuitry starts at pixel "D", therefore the Main Window Display Start Address register (REG[40h]) must be programmed with the address of pixel "D". To calculate the value of the address of pixel "D" use the following formula (assumes 8 bpp color depth). REG[40h] bits 16:0 = ((image address + (offset x (panel height - 1) + panel width) x bpp / 8) / 4) - 1 = ((0 + (480 pixels x 319 pixels + 480 pixels) x 8 bpp / 8) / 4) - 1 = 38399 (95FFh) Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 320 A S1D13A04 X37A-A-001-06 C SwivelView window D B Page 154 Epson Research and Development Vancouver Design Center Line Address Offset The Main Window Line Address Offset register (REG[44h]) is based on the display width and programmed using the following formula. REG[44h] bits 9:0 = display width in pixels / (32 / bpp) = 480 pixels / (32 / 8 bpp) = 120 (78h) 13.4 270 SwivelViewTM 270 SwivelViewTM requires the Memory Clock (MCLK) to be at least 1.25 times the frequency of the Pixel Clock (PCLK), i.e. MCLK 1.25PCLK. The following figure shows how the programmer sees a 320x480 portrait image and how the image is being displayed. The application image is written to the S1D13A04 in the following sense: A-B-C-D. The display is refreshed by the S1D13A04 in the following sense: C-A-D-B. physical memory start address A B A C display start address (panel origin) D C 320 image seen by programmer = image in display buffer D 480 image refreshed by S1D13A04 Figure 13-3: Relationship Between The Screen Image and the Image Refreshed in 270 SwivelView. S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 320 B SwivelView window 480 SwivelView window Epson Research and Development Vancouver Design Center Page 155 13.4.1 Register Programming Enable 270 SwivelViewTM Mode Set SwivelViewTM Mode Select bits (REG[10h] bits 17:16) to 11. Display Start Address The display refresh circuitry starts at pixel "C", therefore the Main Window Display Start Address register (REG[40h]) must be programmed with the address of pixel "C". To calculate the value of the address of pixel "C" use the following formula (assumes 8 bpp color depth). REG[40h] bits 16:0 = (image address + ((panel width - 1) x offset x bpp / 8) / 4) = (0 + ((480 pixels - 1) x 320 pixels x 8 bpp / 8) / 4) = 38320 (95B0h) Line Address Offset The Main Window Line Address Offset register (REG[44h]) is based on the display width and programmed using the following formula. REG[44h] bits 9:0 = display width in pixels / (32 / bpp) = 320 pixels / (32 / 8 bpp) = 80 (50h) Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 156 Epson Research and Development Vancouver Design Center 14 Picture-in-Picture Plus (PIP + ) 14.1 Concept Picture-in-Picture Plus (PIP+) enables a secondary window (or PIP+ window) within the main display window. The PIP+ window may be positioned anywhere within the virtual display and is controlled through the PIP+ Window control registers (REG[50h] through REG[5Ch]). The PIP+ window retains the same color depth and SwivelView orientation as the main window. The following diagram shows an example of a PIP+ window within a main window and the registers used to position it. 0 SwivelViewTM panel's origin PIP+ window y start position (REG[5Ch] bits 9-0) PIP+ window y end position (REG[5Ch] bits 25-16) main-window PIP+ window PIP+ window x start position (REG[58h] bits 9-0) PIP+ window x end position (REG[58h] bits 25-16) Figure 14-1: Picture-in-Picture Plus with SwivelView disabled S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 157 14.2 With SwivelView Enabled 14.2.1 SwivelView 90 90 SwivelViewTM PIP+ window x end position (REG[58h] bits 25-16) PIP+ window panel's origin PIP+ window x start position (REG[58h] bits 9-0) PIP+ window y start position (REG[5Ch] bits 9-0) main-window PIP+ window y end position (REG[5Ch] bits 25-16) Figure 14-2: Picture-in-Picture Plus with SwivelView 90 enabled 14.2.2 SwivelView 180 180 SwivelViewTM PIP+ window x end position (REG[58h] bits 25-16) PIP+ window x start position (REG[58h] bits 9-0) PIP+ window main-window PIP+ window y end position (REG[5Ch] bits 25-16) PIP+ window y start position (REG[5Ch] bits 9-0) panel's origin Figure 14-3: Picture-in-Picture Plus with SwivelView 180 enabled Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 158 Epson Research and Development Vancouver Design Center 14.2.3 SwivelView 270 270 SwivelViewTM PIP+ window y end position (REG[5Ch] bits 25-16) main-window PIP+ window y start position (REG[5Ch] bits 9-0) PIP+ window PIP+ window x start position (REG[58h] bits 9-0) panel's origin PIP+ window x end position (REG[58h] bits 25-16) Figure 14-4: Picture-in-Picture Plus with SwivelView 270 enabled S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 159 15 Power Save Mode A software initiated Power Save Mode is incorporated into the S1D13A04 to accommodate the need for power reduction in the hand-held devices market. This mode is enable via the Power Save Mode Enable bit (REG[14h] bit 4). Software Power Save Mode saves power by powering down the control signals and stopping display refresh accesses to the display buffer. For programming information on disabling the clocks, see the S1D13A04 Programming Notes and Examples, document number X37A-G-003-xx. Table 15-1: Power Save Mode Function Summary Software Power Save IO Access Possible? Memory Writes Possible? Memory Reads Possible? Look-Up Table Registers Access Possible? USB Registers Access Possible? Display Active? LCD I/F Outputs PWMCLK Access Possible for GPIO pins configured for HR-TFT? Access Possible for GPIO Pins configured as GPIOs? USB Running? Yes Yes1 No1 Yes No No Forced Low Stopped Forced Low Yes No 2 Normal Yes Yes Yes Yes Yes Yes Active Active Active Yes Yes Note When power save mode is enabled, the memory controller is powered down and the status of the memory controller is indicated by the Memory Controller Power Save Status bit (REG[14h] bit 6). However, memory writes are possible during power save mode because the S1D13A04 dynamically enables the memory controller for display buffer writes. This ability does not increase power consumption. 2GPIOs can be accessed, and if configured as outputs can be changed. After reset, the S1D13A04 is always in Power Save Mode. Software must initialize the chip (i.e. programs all registers) and then clear the Power Save Mode Enable bit. For further details, see the register description for REG[14h] bit 4. 1 Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 160 Epson Research and Development Vancouver Design Center 16 Mechanical Data 1.2max 10 -0.15 +0.30 0.35 -0.05 +0.10 +0.30 10-0.15 0.1max 0.05max TOP VIEW SIDE VIEW +0.10 0.45 -0.05 0.08 1.0 M L K J H G E D C B 1 2 3 4 5 6 7 8 9 10 11 BOTTOM VIEW All dimensions in mm Figure 16-1: Mechanical Data PFBGA 121-pin Package S1D13A04 X37A-A-001-06 Revision 6.0 1.0 Hardware Functional Specification Issue Date: 2003/05/01 A 0.8 F Epson Research and Development Vancouver Design Center Page 161 16.0 0.4 14.0 0.1 96 97 65 64 Index 128 1 0.4 32 33 0.16 -0.03 +0.05 1.0 0.1 14.0 0.1 16.0 0.4 0.125 -0.025 +0.05 1.2 max 0~10 0.1 0.5 0.2 1.0 All dimensions in mm Figure 16-2: Mechanical Data TQFP15 128-pin Package Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 162 Epson Research and Development Vancouver Design Center 17 References The following documents contain additional information related to the S1D13A04. Document numbers are listed in parenthesis after the document name. All documents can be found at the Epson Research and Development Website at www.erd.epson.com. * 13A04CFG Configuration Utility Users Manual (X37A-B-001-xx) * 13A04PLAY Diagnostic Utility Users Manual (X37A-B-002-xx) * 13A04BMP Demonstration Program User Manual (X37A-B-003-xx) * S1D13A04 Product Brief (X37A-C-001-xx) * S1D13A04 Wind River WindML v2.0 Display Drivers (X37A-E-002-xx) * S1D13A04 Linux Console Driver (X37A-E-004-xx) * S1D13A04 QNX Photon v2.0 Display Drivers (X37A-E-005-xx) * S1D13A04 Windows CE v3.x Display Drivers (X37A-E-006-xx) * Interfacing to the Toshiba TMPR3905/3912 Microprocessor (X37A-G-002-xx) * S1D13A04 Programming Notes And Examples (X37A-G-003-xx) * S5U13A04B00C Rev. 1.0 Evaluation Board User Manual (X37A-G-004-xx) * Interfacing to the PC Card Bus (X37A-G-005-xx) * S1D13A04 Power Consumption (X37A-G-006-xx) * Interfacing to the NEC VR4102/VR4111 Microprocessors (X37A-G-007-xx) * Interfacing to the NEC VR4181 Microprocessor (X37A-G-008-xx) * Interfacing to the Motorola MPC821 Microprocessor (X37A-G-009-xx) * Interfacing to the Motorola MCF5307 "Coldfire" Microprocessors (X37A-G-010-xx) * Connecting to the Sharp HR-TFT Panels (X37A-G-011-xx) * Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor (X37A-G-012-xx) * Interfacing to the Intel StrongARM SA-1110 Microprocessor (X37A-G-013-xx) * S1D13A04 Register Summary (X37A-R-001-xx) S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Epson Research and Development Vancouver Design Center Page 163 18 Sales and Technical Support Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp/ North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com/ Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk/ Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de/ Hardware Functional Specification Issue Date: 2003/05/01 S1D13A04 X37A-A-001-06 Revision 6.0 Page 164 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-A-001-06 Hardware Functional Specification Issue Date: 2003/05/01 Revision 6.0 Errata No. X00Z-P-001-01 Device: Description: S1D13A03, S1D13A04, S1D13A05. Setting EP4 FIFO Valid bit while NAKing an IN token. Bit 5 of REG[402Ch] indicates to the S1D13A0x controller when data in the endpoint 4 FIFO is ready to be transferred to the host computer. Changing the state of this bit at certain times may generate an error. When the S1D13A0x USB controller receives an endpoint 4 IN request and endpoint 4 is not ready to transmit data (REG[402Ch] bit 5 = 0), the response is a NAK packet. If endpoint 4 is toggled to a ready to transmit state just before a NAK response packet is sent, the controller may erroneously send a zero length packet instead. When this happens, the data toggle state will be incorrectly set for the next endpoint 4 data transmit. The following timing diagram shows the error occurring in section 3. 1 2 IN EP4 Token PKT NAK RPLY DATA PKT RPLY 3 IN EP4 Token PKT ZERO Length PKT Host to Device Device to Host CPU Write to EP4_VALID = 1 IN EP4 Token PKT This unexpected occurrence of a zero length packet may cause file system handling errors for some operating systems. Page 2 Epson Research and Development Vancouver Design Center Corrective Action: There are two software solutions for this occurrence. Disable USB Receiver before setting the EP4 FIFO Valid bit The first solution involves disabling the USB receiver to avoid responding to an EP4 IN packet. During the time the USB receiver is disabled the EP4 FIFO Valid bit is set. When the local CPU is ready to send data on endpoint 4 the steps to follow are: 1. 2. 3. 4. 5. Note Disable the USB differential input receiver (REG[4040h] bit 6 = 0) Wait a minimum of 1s. If needed, delays may be added Enable the EP4 FIFO Valid bit (REG[402Ch] bit 5 = 1) Clear the EP4 Interrupt status bit (REG[4004h] bit 4 = 1) Enable the USB differential input receiver (REG[4040h] bit 6 = 1) Steps 1 through 5 are time critical and must be performed in less than 6 s. Note To comply with "EP4 NAK Status not set correctly in USB Status register", steps 3 and 4 must be completed within 5 s of each other. For further information on "EP4 NAK Status not set correctly in USB Status register", see the S1D13A0x Programming Notes and Examples, document numbers X36A-G-003-xx, X37A-G-003-xx, and X40A-G-003-xx. EP4 FIFO Valid bit set after NAK and before the next IN token. The second solution is to wait until immediately after the USB has responded to an IN request with a NAK packet before setting the transmit FIFO valid bit. This solution is recommended only for fast processors. When the local CPU is ready to send data on endpoint 4, it must first detect that a NAK packet has been sent. This is done by reading the EP4 Interrupt Status bit (REG[4004h] bit 4). If the EP4 FIFO Valid bit was not set, the EP4 Interrupt Status bit is set only if a NAK packet has been sent. When the local CPU detects the NAK it must immediately set the EP4 FIFO Valid bit (before responding to the next IN token). After filling the EP4 FIFO the steps to follow before setting the EP4 FIFO Valid bit are: 1. Clear the EP4 Interrupt Status bit (REG[4004h] bit 4) 2. Read the EP4 Interrupt Status bit (REG[4004h] bit 4) until it is set 3. Set the EP4 FIFO Valid bit (REG[402Ch] bit 5 = 1) Note The setting of the EP4 FIFO Valid bit is time critical. The EP4 FIFO Valid bit must be set within 3 s after the EP4 Interrupt Status has been set internally by the S1D13A0x. X00Z-P-001-01 Errata No. X00Z-P-001-01 Issue Date: 2002/08/22 S1D13A04 LCD/USB Companion Chip Programming Notes and Examples Document Number: X37A-G-003-05 Copyright (c) 2001, 2002 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All other trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 3 Table of Contents 1 2 3 4 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Identifying the S1D13A04 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Memory Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1 Display Buffer Location . . . . . . . . . . . . . . . . . . 4.2 Memory Organization for One Bit-per-pixel (2 Colors/Gray Shades) . 4.3 Memory Organization for Two Bit-per-pixel (4 Colors/Gray Shades) . 4.4 Memory Organization for Four Bit-per-pixel (16 Colors/Gray Shades) 4.5 Memory Organization for 8 Bpp (256 Colors/64 Gray Shades) . . . 4.6 Memory Organization for 16 Bpp (65536 Colors/64 Gray Shades) . . Look-Up Table (LUT) . . . . . . . . . 5.1 Registers . . . . . . . . . . . 5.1.1 Look-Up Table Write Register 5.1.2 Look-Up Table Read Registers 5.2 Look-Up Table Organization . . . 5.2.1 Gray Shade Modes . . . . . . 5.2.2 Color Modes . . . . . . . . . . ....... ...... ........ ........ ...... ........ ........ ... .. ... ... .. ... ... ... .. .. ... ... .. .. .. ... .. .. .. ... ... ... .. .. ... ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... .. .. .. .. .. .. . . . . . . . . . . . . . . . . . . . . . 14 14 14 15 15 16 16 17 17 17 18 18 19 22 26 26 27 27 27 28 29 29 30 30 32 36 36 36 37 38 45 45 48 5 ...... ..... ....... ....... ..... ....... ....... ...... ..... ..... ....... ....... ..... ..... ..... ...... ..... ..... ..... ....... ....... ...... ..... ..... ....... ....... ....... ...... ........ ........ ...... ........ ........ ....... ...... ...... ........ ........ ...... ...... ...... ....... ...... ...... ...... ........ ........ ....... ...... ...... ........ ........ 6 Power Save Mode . . . . . . . . . . . . . . . . . . 6.1 Overview . . . . . . . . . . . . . . . . . 6.2 Registers . . . . . . . . . . . . . . . . . 6.2.1 Power Save Mode Enable . . . . . . . . . . . 6.2.2 Memory Controller Power Save Status . . . . 6.3 LCD Power Sequencing . . . . . . . . . . . 6.4 Enabling Power Save Mode . . . . . . . . . . 6.5 Disabling Power Save Mode . . . . . . . . . . SwivelView` . . . . . . . . . . . . . 7.1 SwivelView Registers . . . . . 7.2 Examples . . . . . . . . . . 7.3 Limitations . . . . . . . . . 7.3.1 SwivelView 0 and 180 . . 7.3.2 SwivelView 90 and 270 . . . . . . . . ... .. .. .. ... ... .... .... .... .... ..... ..... .... .... .... ..... ..... 7 8 Picture-In-Picture Plus . . . . . . . . . . . 8.1 Registers . . . . . . . . . . . . . 8.2 Picture-In-Picture-Plus Examples . . . . 8.2.1 SwivelView 0 (Landscape Mode) . 8.2.2 SwivelView 90 . . . . . . . . . . . Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 4 Epson Research and Development Vancouver Design Center 8.2.3 SwivelView 180 . . . . 8.2.4 SwivelView 270 . . . . 8.3 Limitations . . . . . . . . 8.3.1 SwivelView 0 and 180 8.3.2 SwivelView 90 and 270 9 . . . . . ... ... .. ... ... . . . . . ... ... .. ... ... . . . . . ... ... .. ... ... . . . . . ... ... .. ... ... ... .. .. ... ... ... ... ... ... ... ... ... ... ... ... ... .. .. .. . . . . . . . . . . . . . . . . . . . . . . . . ... ... .. ... ... . . . . . ... ... .. ... ... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... ... .. ... ... . . . . . . . 51 . . 54 . .57 . . 57 . . 57 2D BitBLT Engine . . . . . . . . . . . . . . . . . . . . 9.1 Registers . . . . . . . . . . . . . . . . . . . 9.2 BitBLT Descriptions . . . . . . . . . . . . . . 9.2.1 Write BitBLT with ROP . . . . . . . . . . . . . 9.2.2 Color Expansion BitBLT . . . . . . . . . . . . . 9.2.3 Color Expansion BitBLT With Transparency . . . 9.2.4 Solid Fill BitBLT . . . . . . . . . . . . . . . . . 9.2.5 Move BitBLT in a Positive Direction with ROP . 9.2.6 Move BitBLT in Negative Direction with ROP . . 9.2.7 Transparent Write BitBLT . . . . . . . . . . . . . 9.2.8 Transparent Move BitBLT in Positive Direction . 9.2.9 Pattern Fill BitBLT with ROP . . . . . . . . . . . 9.2.10 Pattern Fill BitBLT with Transparency . . . . . . 9.2.11 Move BitBLT with Color Expansion . . . . . . . 9.2.12 Transparent Move BitBLT with Color Expansion 9.2.13 Read BitBLT . . . . . . . . . . . . . . . . . . . . 9.3 S1D13A04 BitBLT Synchronization . . . . . . . . 9.4 S1D13A04 BitBLT Known Limitations . . . . . . 9.5 Sample Code . . . . . . . . . . . . . . . . . ...... ..... ..... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ....... ..... ..... ..... . . . . . .58 . . . . .58 . . . . .66 . . . . . . 67 . . . . . . 70 . . . . . . 74 . . . . . . 74 . . . . . . 76 . . . . . . 78 . . . . . . 79 . . . . . . 82 . . . . . . 84 . . . . . . 86 . . . . . . 88 . . . . . . 89 . . . . . . 89 . . . . .92 . . . . .93 . . . . .93 ... .. ... ... .. ... ... .. ... ... .. ... ... ... ... . . .94 . . .94 . . . 94 . . . 95 . . .95 . . . 95 . . . 96 . . .97 . . . 97 . . .101 . . 106 . . .106 . . .107 . . .107 . . .110 10 Programming the USB Controller . . . . . . . . . . . . . . . . . . . . . 10.1 Registers and Interrupts . . . . . . . . . . . . . . . . . . . . . 10.1.1 Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.1.2 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2 Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2.1 GPIO Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.2.2 USB Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10.3 Data Transfers . . . . . . . . . . . . . . . . . . . . . . . . . 10.3.1 Receiving Data from the Host - the OUT command . . . . . . . . . . 10.3.2 Sending Data to the Host - the IN command . . . . . . . . . . . . . . 10.4 Known Issues . . . . . . . . . . . . . . . . . . . . . . . . . 10.4.1 EP4 NAK Status not set correctly in USB Status Register . . . . . . . 10.4.2 Write to EP4 FIFO Valid bit cleared by NAK . . . . . . . . . . . . . 10.4.3 EP3 Interrupt Status bit set by NAKs . . . . . . . . . . . . . . . . . . 10.4.4 "EP2 Valid Bit" in USB Status can be erroneously set by firmware . . S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 5 10.4.5 Setting EP4 FIFO Valid bit while NAKing IN token . . . . . . . . . . . . . . . . . 110 11 Hardware Abstraction Layer . . . . 11.1 Introduction . . . . . . . . . 11.2 API for the HAL Library . . . . 11.2.1 Startup Routines . . . . . . . 11.2.2 Memory Access . . . . . . . 11.2.3 Register Access . . . . . . . 11.2.4 Clock Support . . . . . . . . 11.2.5 Miscellaneous . . . . . . . . . . . . . . . . ....... ...... ...... ........ ........ ........ ........ ........ ... .. .. ... ... ... ... ... . . . . . . . . ...... ..... ..... ....... ....... ....... ....... ....... . . . . . . . . . . . . . . . 112 . . . . . . 112 . . . . . . 112 . . . . . . . . 113 . . . . . . . . 115 . . . . . . . . 116 . . . . . . . . 118 . . . . . . . . 119 12 Sample Code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 13 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 6 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 7 List of Tables Table 5-1: Look-Up Table Configurations . . . . . . . . . . . . . . . . . . . . . . . Table 5-2: Suggested LUT Values for 1 Bpp Gray Shade . . . . . . . . . . . . . . . Table 5-3: Suggested LUT Values for 4 Bpp Gray Shade . . . . . . . . . . . . . . . Table 5-4: Suggested LUT Values for 4 Bpp Gray Shade . . . . . . . . . . . . . . . Table 5-5: Suggested LUT Values for 8 Bpp Gray Shade . . . . . . . . . . . . . . . Table 5-6: Suggested LUT Values for 1 bpp Color . . . . . . . . . . . . . . . . . . . Table 5-7: Suggested LUT Values for 2 bpp Color . . . . . . . . . . . . . . . . . . . Table 5-8: Suggested LUT Values for 4 bpp Color . . . . . . . . . . . . . . . . . . . Table 5-9: Suggested LUT Values 8 bpp Color . . . . . . . . . . . . . . . . . . . . . Table 7-1: SwivelView Mode Select Bits . . . . . . . . . . . . . . . . . . . . . . . . Table 8-1: 32-bit Address Increments for PIP+ X Position in SwivelView 0 and 180 Table 8-2: 32-bit Address Increments for Color Depth . . . . . . . . . . . . . . . . . Table 8-3: 32-bit Address Increments for Color Depth . . . . . . . . . . . . . . . . . Table 8-4: 32-bit Address Increments for Color Depth . . . . . . . . . . . . . . . . . Table 9-1: BitBLT FIFO Words Available . . . . . . . . . . . . . . . . . . . . . . . Table 9-2 : BitBLT ROP Code/Color Expansion Function Selection . . . . . . . . . . Table 9-3 : BitBLT Operation Selection . . . . . . . . . . . . . . . . . . . . . . . . . Table 9-4 : BitBLT Source Start Address Selection . . . . . . . . . . . . . . . . . . . Table 9-5: Possible BitBLT FIFO Writes . . . . . . . . . . . . . . . . . . . . . . . . Table 9-6: Possible BitBLT FIFO Writes . . . . . . . . . . . . . . . . . . . . . . . . Table 9-7: Possible BitBLT FIFO Writes . . . . . . . . . . . . . . . . . . . . . . . . Table 9-8: Possible BitBLT FIFO Reads . . . . . . . . . . . . . . . . . . . . . . . . Table 10-1: USB Controller Initialization Sequence . . . . . . . . . . . . . . . . . . . Table 11-1: HAL Library API . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 . 19 . 19 . 20 . 21 . 22 . 22 . 23 . 24 . 30 . 40 . 41 . 42 . 44 . 60 . 61 . 62 . 63 . 69 . 74 . 82 . 91 . 96 . 112 Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 8 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 9 List of Figures Figure 4-1: Figure 4-2: Figure 4-3: Figure 4-4: Figure 4-5: Figure 8-1: Figure 8-2: Figure 8-3: Figure 8-4: Figure 8-5: Figure 9-1: Figure 10-1: Figure 10-2: Figure 10-3: Figure 10-4: Figure 10-5: Figure 10-6: Figure 10-7: Pixel Storage for 1 Bpp in One Byte of Display Buffer . . . Pixel Storage for 2 Bpp in One Byte of Display Buffer . . . Pixel Storage for 4 Bpp in One Byte of Display Buffer . . . Pixel Storage for 8 Bpp in One Byte of Display Buffer . . . Pixel Storage for 16 Bpp in Two Bytes of Display Buffer . Picture-in-Picture Plus with SwivelView disabled . . . . . Picture-in-Picture Plus with SwivelView disabled . . . . . Picture-in-Picture Plus with SwivelView 90 enabled . . . . Picture-in-Picture Plus with SwivelView 180 enabled . . . Picture-in-Picture Plus with SwivelView 270 enabled . . . Move BitBLT Usage . . . . . . . . . . . . . . . . . . . . . Endpoint 1 Data Reception . . . . . . . . . . . . . . . . . Endpoint 3 Data Reception . . . . . . . . . . . . . . . . . EndPoint 2 Data Transmission . . . . . . . . . . . . . . . . Endpoint 4 Data Transmission . . . . . . . . . . . . . . . . Endpoint 4 Interrupt Handling . . . . . . . . . . . . . . . . Firmware Looping Continuously on Received OUT packets Endpoint 3 Program Flow for Slow CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 . 15 . 15 . 16 . 16 . 37 . 45 . 48 . 51 . 54 . 76 . 98 100 102 103 105 108 109 Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 10 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 11 1 Introduction This guide discusses programming issues and provides examples for the main features of the S1D13A04, such as SwivelView, Picture-in-Picture Plus, and the BitBLT engine. The example source code referenced in this guide is available on the web at www.erd.epson.com. This guide also introduces the Hardware Abstraction Layer (HAL), which is designed to simplify the programming of the S1D13A04. Most S1D13xxx products have HAL support, thus allowing OEMs to do multiple designs with a common code base. This document is updated as appropriate. Please check the Epson Research and Development website at www.erd.epson.com for the latest revision of this document and source before beginning any development. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 12 Epson Research and Development Vancouver Design Center 2 Identifying the S1D13A04 The S1D13A04 can be identified by reading the value contained in the Product Information Register (REG[00h]). To identify the S1D13A04 follow the steps below. 1. Read REG[00h]. 2. The production version of the S1D13A04 returns a value of 2Cxx282Ch (where xx depends on the configuration of the CNF[6:0] pins). This value can be broken down into the following. 1. The product code for the S1D13A04 is 0Bh (001011 binary) and can be found in bits 7-2 and also in bits 31-26. 2. The revision code is 0h (00 binary) and can be found in bits 1-0 and again in bits 25-24. 3. The display buffer size is 28h (00101000 binary) and is contained in bits 15-8. Note The display buffer size is the distinguishing value between the S1D13A03 and the S1D13A04 as they share the same product code and revision code. For the correct display buffer size for the S1D13A03, see the S1D13A03 Hardware Functional Specification, document number X36A-A-001-xx. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 13 3 Initialization This section describes how to initialize the S1D13A04. Sample code for performing initialization of the S1D13A04 is provided in the file init13A04.c which is available on the internet at www.erd.epson.com. S1D13A04 initialization can be broken into the following steps. 1. Set all registers to initial values. The values are obtained by using the S1D13A04.h file that is exported by the 13A04CFG.EXE configuration utility. For more information on 13A04CFG, see the 13A04CFG User Manual, document number X37A-B-001-xx. 2. Program the Look-Up Table (LUT) with color values. For details on programming the LUT, see Section 5, "Look-Up Table (LUT)" on page 17. 3. Clear the display buffer. If the system implementation uses a clock chip instead of a fixed oscillator, refer to the HAL (Hardware Abstraction Layer) sample code available on the internet at www.erd.epson.com. For example, the Epson S5U13A04B00C evaluation board uses a Cypress clock chip. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 14 Epson Research and Development Vancouver Design Center 4 Memory Models The S1D13A04 contains a display buffer of 160K bytes and supports color depths of 1, 2, 4, 8, and 16 bit-per-pixel. For each color depth, the data format is packed pixel. Packed pixel data may be envisioned as a stream of pixels. In this stream, pixels are packed adjacent to each other. If a pixel requires four bits, then it is located in the four most significant bits of a byte. The pixel to the immediate right on the display occupies the lower four bits of the same byte. The next two pixels to the immediate right are located in the following byte, etc. 4.1 Display Buffer Location The S1D13A04 display buffer is 160K bytes of embedded SRAM. The display buffer is memory mapped and is accessible directly by software. The memory block location assigned to the S1D13A04 display buffer varies with each individual hardware platform. For further information on the display buffer, see the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. For further information on the S1D13A04 Evaluation Board, see the S5U13A04B00C Evaluation Board Rev. 1.0 User Manual, document number X37A-G-004-xx. 4.2 Memory Organization for One Bit-per-pixel (2 Colors/Gray Shades) Bit 7 Pixel 0 Bit 6 Pixel 1 Bit 5 Pixel 2 Bit 4 Pixel 3 Bit 3 Pixel 4 Bit 2 Pixel 5 Bit 1 Pixel 6 Bit 0 Pixel 7 Figure 4-1: Pixel Storage for 1 Bpp in One Byte of Display Buffer At a color depth of 1 bpp, each byte of display buffer contains eight adjacent pixels. Setting or resetting any pixel requires reading the entire byte, masking out the unchanged bits and setting the appropriate bits to 1. One bit pixels provide 2 gray shades/color possibilities. For monochrome panels the gray shades are generated by indexing into the first two elements of the green component of the Look-Up Table (LUT). For color panels the 2 colors are derived by indexing into the first 2 positions of the LUT. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 15 4.3 Memory Organization for Two Bit-per-pixel (4 Colors/Gray Shades) Bit 7 Pixel 0 bits 1-0 Bit 6 Bit 5 Pixel 1 bits 1-0 Bit 4 Bit 3 Pixel 2 bits 1-0 Bit 2 Bit 1 Pixel 3 bits 1-0 Bit 0 Figure 4-2: Pixel Storage for 2 Bpp in One Byte of Display Buffer At a color depth of 2 bpp, each byte of display buffer contains four adjacent pixels. Setting or resetting any pixel requires reading the entire byte, masking out the unchanged bits and setting the appropriate bits to 1. Two bit pixels provide 4 gray shades/color possibilities. For monochrome panels the gray shades are generated by indexing into the first 4 elements of the green component of the Look-Up Table (LUT). For color panels the 4 colors are derived by indexing into the first 4 positions of the LUT. 4.4 Memory Organization for Four Bit-per-pixel (16 Colors/Gray Shades) Bit 7 Bit 6 Pixel 0 bits 3-0 Bit 5 Bit 4 Bit 3 Bit 2 Pixel 1 bits 3-0 Bit 1 Bit 0 Figure 4-3: Pixel Storage for 4 Bpp in One Byte of Display Buffer At a color depth of 4 bpp, each byte of display buffer contains two adjacent pixels. Setting or resetting any pixel requires reading the entire byte, masking out the upper or lower nibble (4 bits) and setting the appropriate bits to 1. Four bit pixels provide 16 gray shades/color possibilities. For monochrome panels the gray shades are generated by indexing into the first 16 elements of the green component of the Look-Up Table (LUT). For color panels the 16 colors are derived by indexing into the first 16 positions of the LUT. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 16 Epson Research and Development Vancouver Design Center 4.5 Memory Organization for 8 Bpp (256 Colors/64 Gray Shades) Bit 7 Bit 6 Bit 5 Bit 4 Pixel 0 bits 7-0 Bit 3 Bit 2 Bit 1 Bit 0 Figure 4-4: Pixel Storage for 8 Bpp in One Byte of Display Buffer At a color depth of 8 bpp, each byte of display buffer represents one pixel on the display. At this color depth the read-modify-write cycles are eliminated making the update of each pixel faster. Each byte indexes into one of the 256 positions of the LUT. The S1D13A04 LUT supports six bits per primary color. This translates into 256K possible colors when color mode is selected. Therefore the display has 256 colors available out of a possible 256K colors. When a monochrome panel is selected, the green component of the LUT is used to determine the intensity. The green indices, with six bits, can resolve 64 gray shades. Display memory values > 64 are truncated. Thus a display memory value of 65 (1000 0001) displays the same intensity as a display memory value of 1. 4.6 Memory Organization for 16 Bpp (65536 Colors/64 Gray Shades) Bit 15 Bit 14 Bit 13 Red Component bits 4-0 Bit 7 Bit 6 Green Component bits 2-0 Bit 5 Bit 4 Bit 3 Bit 2 Blue Component bits 4-0 Bit 12 Bit 11 Bit 10 Bit 9 Green Component bits 5-3 Bit 1 Bit 0 Bit 8 Figure 4-5: Pixel Storage for 16 Bpp in Two Bytes of Display Buffer At a color depth of 16 bpp the S1D13A04 is capable of displaying 64K (65536) colors. The 64K color pixel is divided into three parts: five bits for red, six bits for green, and five bits for blue. In this mode the LUT is bypassed and output goes directly into the Frame Rate Modulator. Should monochrome mode be chosen at this color depth, the output sends the six bits of the green LUT component to the modulator for a total of 64 possible gray shades. Note This operation is similar to 8 bpp, but it requires twice as much memory for the display. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 17 5 Look-Up Table (LUT) This section discusses programming the S1D13A04 Look-Up Table (LUT). Included is a summary of the LUT registers, recommendations for color/gray shade LUT values, and additional programming considerations. For a discussion of the LUT architecture, refer to the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. The S1D13A04 is designed with a LUT consisting of 256 indexed red/green/blue entries. Each LUT entry is six bits wide. The color depth (bpp) determines how many indices are used. For example, 1 bpp uses the first 2 indices, 2 bpp uses the first 4 indices, 4 bpp uses the first 16 indices and 8 bpp uses all 256 indices. 16 bpp bypasses the LUT. In color modes, the pixel values stored in the display buffer index directly to an RGB value stored in the LUT. In monochrome modes, the pixel value indexes into the green component of the LUT and the amount of green at that index controls the intensity. 5.1 Registers 5.1.1 Look-Up Table Write Register Look-Up Table Write Register REG[18h] Default = 00000000h LUT Write Address 31 15 30 14 29 28 LUT Green Write Data 13 12 27 11 26 10 25 n/a 9 8 7 6 24 23 22 LUT Red Write Data 21 20 LUT Blue Write Data 5 4 19 3 18 2 17 n/a 1 0 Write Only n/a 16 This register receives the data to be written to the red (bits 23-18), green (bits 15-10), and blue (bits 7-2) components of the Look-Up Table (LUT). Also contained in this register is the LUT Write Address (bits 31-24) which forms a pointer to the location in the LUT where the RGB components will be written. This register should be accessed using a 32-bit write cycle to ensure proper operation. If the Look-Up Table Write Register is accessed with 8 or 16-bit write, it is important to understand that the LUT data is latched into the LUT only after the completion of the write to the LUT Write Address bits. On little endian systems, this means a write to bits 31-24. On big endian systems, this means a write to bits 7-2. This is a write-only register and returns 00h if read. Note For further information on the S1D13A04 LUT architecture, see the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 18 Epson Research and Development Vancouver Design Center 5.1.2 Look-Up Table Read Registers Look-Up Table Read Register REG[1Ch] Default = 00000000h LUT Read Address (write only) 31 15 30 14 29 28 LUT Green Read Data 13 12 27 11 26 10 25 n/a 9 8 7 6 24 23 22 Write Only (bits 31-24)/Read Only LUT Red Read Data 21 20 LUT Blue Read Data 5 4 19 3 18 2 17 n/a 1 0 n/a 16 This register contains the data returned from the red (bits 23-18), green (bits 15-10), and blue (bits 7-2) components of the Look-Up Table (LUT). Also contained in this register is the LUT Read Address (bits 31-24) which forms a pointer to the location in the LUT where the RGB components are read from. Reading the LUT is a two step process. First the desired index must be set by writing the LUT Read Address bits with the desired index. Second, the LUT values are retrieved by reading from the Look-Up Table Read Register. Bits 31-24 are write only and will return 00h if read. Note For further information on the S1D13A04 LUT architecture, see the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. 5.2 Look-Up Table Organization * The Look-Up Table treats the value of a pixel as an index into an array. For example, a pixel value of zero would point to the first LUT entry, whereas a pixel value of seven would point to the eighth LUT entry. * The value contained in each LUT entry represents the intensity of the given color or gray shade. This intensity can range in value from 0 to 3Fh. * The S1D13A04 Look-Up Table is linear. This means increasing the LUT entry number results in a brighter color or gray shade. For example, a LUT entry of FCh in the red bank results in bright red output while a LUT entry of 1Ch results in dull red. Table 5-1: Look-Up Table Configurations Color Depth 1 bpp gray 2 bpp gray 4 bpp gray 8 bpp gray 16 bpp gray 1 bpp color 2 bpp color 4 bpp color 8 bpp color 16 bpp color Look-Up Table Indices Used RED GREEN BLUE 2 4 16 64 2 4 16 256 2 4 16 256 2 4 16 256 Effective Gray Shades/Colors 2 gray shades 4 gray shades 16 gray shades 64 gray shades 64 gray shades 2 colors 4 colors 16 colors 256 colors 65536 colors = Indicates the Look-Up Table is not used for that display mode S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 19 5.2.1 Gray Shade Modes Gray shade (monochrome) modes are defined by the Color/Mono Panel Select bit (REG[0Ch] bit 6). When this bit is set to 0, the value output to the panel is derived solely from the green component of the LUT. For each gray shade a table of sample LUT values is provided. These LUT values are a standardized set of intensities used by the Epson S1D13A04 utility programs. Note These LUT values carry eight bits of significance. The S1D13A04 LUT uses only the six MSB. The 2 LSB are ignored. 1 bpp gray shade The 1 bpp gray shade mode uses the green component of the first 2 LUT entries. The remaining indices of the LUT are unused. Table 5-2: Suggested LUT Values for 1 Bpp Gray Shade Index 00 01 02 ... FF Red 00 00 00 00 00 Green 00 FF 00 00 00 Unused entries Blue 00 00 00 00 00 2 bpp gray shade The 2 bpp gray shade mode uses the green component of the first 4 LUT entries. The remaining indices of the LUT are unused. Table 5-3: Suggested LUT Values for 4 Bpp Gray Shade Index 00 01 02 03 04 ... FF Red 00 00 00 00 00 00 00 Green 00 55 AA FF 00 00 00 Unused entries Blue 00 00 00 00 00 00 00 Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 20 Epson Research and Development Vancouver Design Center 4 bpp gray shade The 4 bpp gray shade mode uses the green component of the first 16 LUT entries. The remaining indices of the LUT are unused. Table 5-4: Suggested LUT Values for 4 Bpp Gray Shade Index 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 ... FF Red 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Green 00 10 20 34 44 54 68 78 88 9C AC BC CC DC EC FC 00 00 00 Unused entries Blue 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 21 8 bpp gray shade When configured for 8 bpp gray shade mode, the green component of all 256 LUT entries may be used. However, this results in redundant values where each of the 256 pixel values can only be mapped into 1 of 64 gray shades. Table 5-5: Suggested LUT Values for 8 Bpp Gray Shade Index 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F Red 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Green 00 04 08 0C 10 14 18 1C 20 24 28 2C 30 34 38 3C 40 44 48 4C 50 54 58 5C 60 64 68 6C 70 74 78 7C Blue 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Index 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 ... FF Red 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Green 80 84 88 8C 90 94 98 9C A0 A4 A8 AC B0 B4 B8 BC C0 C4 C8 CC D0 D4 D8 DC E0 E4 E8 EC F0 F4 F8 FC 00 00 00 Blue 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Unused entries Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 22 Epson Research and Development Vancouver Design Center 16 bpp gray shade The Look-Up Table is bypassed at this color depth, therefore programming the LUT is not required. As with 8 bpp there are limitations to the colors which can be displayed. In this mode the six bits of green are used to set the absolute intensity of the image. This results in 64 gray shades. 5.2.2 Color Modes In color display modes, the number of LUT entries used is determined by the color depth. For each color depth a table of sample LUT values is provided. These LUT values are a standardized set of colors used by the Epson S1D13A04 utility programs. Note These LUT values carry eight bits of significance. The S1D13A04 LUT uses only the six MSB. The 2 LSB are ignored. 1 bpp color When the S1D13A04 is configured for 1 bpp color mode the first 2 entries in the LUT are used. The remaining indices of the LUT are unused. Table 5-6: Suggested LUT Values for 1 bpp Color Index 00 01 02 ... FF Red 00 FF 00 00 00 Green 00 FF 00 00 00 Blue 00 FF 00 00 00 = Indicates unused entries in the LUT 2 bpp color When the S1D13A04 is configured for 2 bpp color mode the first 4 entries in the LUT are used. The remaining indices of the LUT are unused. Table 5-7: Suggested LUT Values for 2 bpp Color Index 00 01 02 03 04 ... FF Red 00 00 FF FF 00 00 00 Green 00 00 00 FF 00 00 00 Blue 00 FF 00 FF 00 00 00 = Indicates unused entries in the LUT S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 23 4 bpp color When the S1D13A04 is configured for 4 bpp color mode the first 16 entries in the LUT are used. The remaining indices of the LUT are unused. The following table shows LUT values that simulate those of a VGA operating in 16 color mode. Table 5-8: Suggested LUT Values for 4 bpp Color Index 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 ... FF Red 00 00 00 00 AA AA AA AA 00 00 00 00 FF FF FF FF 00 00 00 Green 00 00 AA AA 00 00 AA AA 00 00 FF FF 00 00 FF FF 00 00 00 Blue 00 AA 00 AA 00 AA 00 AA 00 FF 00 FF 00 FF 00 FF 00 00 00 = Indicates unused entries in the LUT Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 24 Epson Research and Development Vancouver Design Center 8 bpp color When the S1D13A04 is configured for 8 bpp color mode all 256 entries in the LUT are used. The S1D13A04 LUT has six bits (64 intensities) of intensity control per primary color which is the same as a standard VGA RAMDAC. The following table shows LUT values that simulate the VGA default color palette. Table 5-9: Suggested LUT Values 8 bpp Color Index 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 R 00 00 00 00 AA AA AA AA 55 00 00 00 FF FF FF FF 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF 00 11 22 33 G 00 00 AA AA 00 00 AA AA 55 00 FF FF 00 00 FF FF 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF 00 00 00 00 B 00 AA 00 AA 00 AA 00 AA 55 FF 00 FF 00 FF 00 FF 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF 00 00 00 00 Index 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 R 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 G 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF FF FF FF FF B 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF EF DE CD Index 80 81 82 83 84 85 86 87 88 89 8A 8B 8C 8D 8E 8F 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9E 9F A0 A1 A2 A3 R FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF EF DE CD G FF EF DE CD BC AB 9A 89 77 66 55 44 33 22 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 B 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF FF FF FF FF Index C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF E0 E1 E2 E3 R 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 00 11 22 33 G 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF FF FF FF FF B 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF 00 11 22 33 S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 25 Table 5-9: Suggested LUT Values 8 bpp Color (Continued) Index 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F R 44 55 66 77 89 9A AB BC CD DE EF FF 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 G 00 00 00 00 00 00 00 00 00 00 00 00 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF B 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Index 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F R 00 00 00 00 00 00 00 00 00 00 00 00 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF G FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF B BC AB 9A 89 77 66 55 44 33 22 11 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Index A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF R BC AB 9A 89 77 66 55 44 33 22 11 00 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF G 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 B FF FF FF FF FF FF FF FF FF FF FF FF 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF Index E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF R 44 55 66 77 89 9A AB BC CD DE EF FF 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF G FF FF FF FF FF FF FF FF FF FF FF FF 00 11 22 33 44 55 66 77 89 9A AB BC CD DE EF FF B 44 55 66 77 89 9A AB BC CD DE EF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF 16 bpp color The Look-Up Table is bypassed at this color depth, therefore programming the LUT is not required. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 26 Epson Research and Development Vancouver Design Center 6 Power Save Mode The S1D13A04 is designed for very low-power applications. During normal operation, the internal clocks are dynamically disabled when not required. The S1D13A04 design also includes a Power Save Mode to further save power. When Power Save Mode is initiated, LCD power sequencing is required to ensure the LCD bias power supply is disabled properly. For further information on LCD power sequencing, see Section 6.3, "LCD Power Sequencing" on page 28. For Power Save Mode AC Timing, see the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. 6.1 Overview The S1D13A04 includes a software initiated Power Save Mode. Enabling/disabling Power Save Mode is controlled using the Power Save Mode Enable bit (REG[14h] bit 4). While Power Save Mode is enabled the following conditions apply. * Registers are accessible (USB registers are not accessible) * Memory writes are possible1 * Memory reads are not possible * LCD display is inactive. * LCD interface outputs are forced low. Note Memory writes are possible during power save mode because the S1D13A04 dynamically enables the memory controller for display buffer writes. 1 S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 27 6.2 Registers 6.2.1 Power Save Mode Enable Power Save Configuration Register REG[14h] Default = 00000010h n/a 31 30 29 28 27 26 25 24 23 VNDP Status (RO) 11 10 9 8 7 22 Memory Power Save Status (RO) 6 21 20 Power Save Mode Enable 4 3 19 18 17 16 `Direct' HR-TFT GPO Control 1 0 Read/Write n/a n/a n/a 15 14 13 12 5 2 The Power Save Mode Enable bit initiates Power Save Mode when set to 1. Setting the bit to 0 disables Power Save Mode and returns the S1D13A04 to normal mode. At reset this bit is set to 1. Note Enabling/disabling Power Save Mode requires proper LCD Power Sequencing. See Section 6.3, "LCD Power Sequencing" on page 28. 6.2.2 Memory Controller Power Save Status Power Save Configuration Register REG[14h] Default = 00000010h n/a 31 30 29 28 27 26 25 24 23 VNDP Status (RO) 11 10 9 8 7 22 Memory Power Save Status (RO) 6 21 20 Power Save Mode Enable 4 3 19 18 17 16 `Direct' HR-TFT GPO Control 1 0 Read/Write n/a n/a n/a 15 14 13 12 5 2 The Memory Controller Power Save Status bit is a read-only status bit which indicates the power save state of the S1D13A04 SRAM interface. When this bit returns a 1, the SRAM interface is powered down and the memory clock source may be disabled. When this bit returns a 0, the SRAM interface is active. This bit returns a 0 after a chip reset. Note Memory writes are possible during power save mode because the S1D13A04 dynamically enables the memory controller for display buffer writes. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 28 Epson Research and Development Vancouver Design Center 6.3 LCD Power Sequencing The S1D13A04 requires LCD power sequencing (the process of powering-on and powering-off the LCD panel). LCD power sequencing allows the LCD bias voltage to discharge prior to shutting down the LCD signals, preventing long term damage to the panel and avoiding unsightly "lines" at power-on/power-off. Proper LCD power sequencing for power-off requires a delay from the time the LCD power is disabled to the time the LCD signals are shut down. Power-on requires the LCD signals to be active prior to applying power to the LCD. This time interval depends on the LCD bias power supply design. For example, the LCD bias power supply on the S5U13A04B00C Evaluation Board requires 0.5 seconds to fully discharge. Other power supply designs may vary. This section assumes the LCD bias power is controlled through GPIO0. The S1D13A04 GPIO pins are multi-use pins and may not be available in all system designs. For further information on the availability of GPIO pins, see the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. Note This section discusses LCD power sequencing for passive and TFT (non-HR-TFT) panels only. For further information on LCD power sequencing the HR-TFT, see Connecting to the Sharp HR-TFT Panels, document number X37A-G-011-xx. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 29 6.4 Enabling Power Save Mode Power Save Mode must be enabled using the following steps. 1. Turn off the LCD bias power. Note The S5U13A04B00C uses GPIO0 to control the LCD bias power supplies. Your system design may vary. 2. Wait for the LCD bias power supply to discharge. The discharge time is based on the discharge rate of the power supply. 3. Enable Power Save Mode - set REG[14h] bit 4 to 1. The S1D13A04 is now in Power Save Mode. To further increase power savings PCLK and MCLK can be switched off (see steps 4 and 5). 4. At this time, the LCD pixel clock source may be disabled. 5. After the Memory Controller Power Save Status bit (REG[14h] bit 6) returns a 1, the Memory Clock source may be shut down. 6.5 Disabling Power Save Mode Bring the S1D13A04 out of Power Save Mode using the following steps. 1. If the Memory Clock source is shut down, it must be started. 2. If the pixel clock is disabled, it must be started. 3. Disable Power Save Mode - set REG[14h] bit 4 to 0. 4. Wait for the LCD bias power supply to charge. The charge is based on the time required for the LCD power supply to reach operating voltage. 5. Enable the LCD bias power. Note The S5U13A04B00C uses GPIO0 to control the LCD bias power supplies. Your system design may vary. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 30 Epson Research and Development Vancouver Design Center 7 SwivelView Most computer displays operate in landscape mode. In landscape mode the display is typically wider than it is high. For example, a display size of 320x240 is 320 pixels wide and 240 lines high. SwivelView rotates the display image counter-clockwise in ninety degree increments. Rotating the image on a 320x240 display by 90 or 270 degrees yields a display that is now 240 pixels wide and 320 lines high. The S1D13A04 provides hardware support for SwivelView in all color depths (1, 2, 4, 8 and 16 bpp). For further details on the SwivelView feature, see the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. 7.1 SwivelView Registers These are the registers which control the SwivelView feature. Display Settings Register REG[10h] Default = 00000000h Pixel n/a Vertical 31 30 29 28 27 26 n/a 15 14 13 12 11 10 9 8 7 6 5 4 25 Pixel Display Blank 23 Dithering Disable 22 n/a Horiz. 24 21 Doubling Doubling SW Video Invert 20 PIP+ Window Enable n/a Read/Write SwivelView Mode Select 16 19 18 17 Bits-per-pixel Select (actual value: 1, 2, 4, 8 or 16 bpp) 3 2 1 0 SwivelView Mode Select The SwivelView modes are selected using the SwivelView Mode Select Bits[1:0] (bits 1716). The combinations of these bits provide the following rotations. Table 7-1: SwivelView Mode Select Bits SwivelView Mode Select Bit 1 0 0 1 1 SwivelView Mode Select Bit 0 0 1 0 1 SwivelView Orientation 0 (normal) 90 180 270 S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 31 Main Window Display Start Address Register REG[40h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 10 25 24 23 22 21 Main Window Display Start Address bits 15-0 9 8 7 6 5 20 4 19 3 18 2 Read/Write bit 16 17 1 16 0 Main Window Display Start Address The Main Window Display Start Address register represents a DWORD address which points to the start of the main window image in the display buffer. An address of 0 is the start of the display buffer. For the following SwivelView mode descriptions, the desired byte address is the starting display address for the main window image. In SwivelView 0, program the start address = desired byte address / 4 In SwivelView 90, program the start address = ((desired byte address + (panel height x bpp / 8) + ((4 - (panel height x bpp / 8)) & 03h)) / 4) - 1 In SwivelView 180, program the start address = ((desired byte address + (Main Window Stride x (panel height - 1)) + (panel width x bpp / 8) + ((4 - (panel width x bpp / 8)) & 03h)) / 4) - 1 In SwivelView 270, program the start address = (desired byte address + ((panel width - 1) x Main Window Stride)) / 4 Note Truncate all fractional values before writing to the address registers. Note SwivelView 0 and 180 require the panel width to be a multiple of 32 / bits-per-pixel. SwivelView 90 and 270 require the panel height to be a multiple of 32 / bits-per-pixel. If this is not possible, refer to Section 7.3, "Limitations" . Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 32 Epson Research and Development Vancouver Design Center Main Window Line Address Offset Register REG[44h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 28 27 26 25 24 23 22 21 20 19 Main Window Line Address Offset bits 9-0 6 5 4 3 18 2 Read/Write 17 1 16 0 Main Window Line Address Offset The Main Window Line Address Offset register indicates the number of dwords per line in the main window image. For SwivelView 0 and 180, the image width must be at least the panel width. For SwivelView 90 and 270, the image width must be at least the panel height. In addition, the image width must be a multiple of 32 / bpp. If the image width is not such a multiple, a slightly larger width must be chosen (see Section 7.3, "Limitations" ). Panel width and panel height refer to the physical panel dimensions in pixels. Stride is the number of bytes required for one line of the image; the offset register represents the stride in DWORD steps. Main Window Stride = image width x bpp / 8 Note Image width can be larger than panel width (or panel height, for SwivelView 90 or 270). number of dwords per line = image width / (32 / bpp) 7.2 Examples Example 1: In SwivelView 0 (normal) mode, program the main window registers for a 320x240 panel at a color depth of 4 bpp. 1. Determine the main window display start address. The main window is typically placed at the start of display memory which is at display address 0. main window display start address register = desired byte address / 4 =0 Program the Main Window Display Start Address register. REG[40h] is set to 00000000h. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 33 2. Determine the main window line address offset. number of dwords per line = image width / (32 / bpp) = 320 / (32 / 4) = 40 = 28h Program the Main Window Line Address Offset register. REG[44h] is set to 00000028h. Example 2: In SwivelView 90 mode, program the main window registers for a 320x240 panel at a color depth of 4 bpp. 1. Determine the main window display start address. The main window is typically placed at the start of display memory, which is at display address 0. main window display start address register = ((desired byte address + (panel height x bpp / 8) + ((4 - (panel height x bpp / 8)) & 03h)) / 4) - 1 = ((0 + (240 x 4 / 8) + ((4 - (240 x 4 / 8)) & 03h)) / 4) - 1 = 29 = 1Dh Program the Main Window Display Start Address register. REG[40h] is set to 0000001Dh. 2. Determine the main window line address offset. number of dwords per line = image width / (32 / bpp) = 240 / (32 / 4) = 30 = 1Eh Program the Main Window Line Address Offset register. REG[44h] is set to 0000001Eh. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 34 Epson Research and Development Vancouver Design Center Example 3: In SwivelView 180 mode, program the main window registers for a 320x240 panel at a color depth of 4 bpp. 1. Determine the main window display start address. The main window is typically placed at the start of display memory which is at display address 0. Main Window Stride = image width x bpp / 8 = 320 x 4 / 8 = 160 = A0h main window display start address register = ((desired byte address + (Main Window Stride x (panel height - 1)) + (panel width x bpp / 8) + ((4 - (panel width x bpp / 8)) & 03h)) / 4) - 1 = ((0+(160 x (240 - 1)) + (320 x 4 / 8) + ((4 - (320 x 4 / 8))& 03h)) / 4) - 1 = 9599 = 257Fh Program the Main Window Display Start Address register. REG[40h] is set to 0000257Fh. 2. Determine the main window line address offset. number of dwords per line = image width / (32 / bpp) = 320 / (32 / 4) = 40 = 28h Program the Main Window Line Address Offset register. REG[44h] is set to 00000028h. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 35 Example 4: In SwivelView 270 mode, program the main window registers for a 320x240 panel at a color depth of 4 bpp. 1. Determine the main window display start address. The main window is typically placed at the start of display memory, which is at display address 0. Main Window Stride = image width x bpp / 8 = 240 x 4 / 8 = 120 = 78h main window display start address register = (desired byte address + ((panel width - 1) x Main Window Stride)) / 4 = (0 + ((320 - 1) x 120)) / 4 = 9570 = 2562h Program the Main Window Display Start Address register. REG[40h] is set to 00002562h. 2. Determine the main window line address offset. number of dwords per line = image width / (32 / bpp) = 240 / (32 / 4) = 30 = 1Eh Program the Main Window Line Address Offset register. REG[44h] is set to 0000001Eh. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 36 Epson Research and Development Vancouver Design Center 7.3 Limitations 7.3.1 SwivelView 0 and 180 In SwivelView 0 and 180, the Main Window Line Address Offset register (REG[44h]) requires the panel width to be a multiple of 32 / bits-per-pixel. If this is not the case, then the Main Window Line Address Offset register must be programmed to a longer line which meets this requirement. This longer line creates a virtual image where the width is main window line address offset register x 32 / bits-per-pixel. In SwivelView 0, this virtual image should be drawn in display memory as left justified, and in SwivelView 180, this virtual image should be drawn in display memory as right justified. A left-justified image is one drawn in display memory such that each of the image's lines only use the left most portion of the line width defined by the line address offset register (i.e. starting at horizontal position 0). A right-justified image is one drawn in display memory such that each of the image's lines only use the right most portion of the line width defined by the line address offset register (i.e. starting at a non-zero horizontal position which is the virtual width image width). 7.3.2 SwivelView 90 and 270 In SwivelView 90 and 270, the Main Window Line Address Offset register (REG[44h]) requires the panel height to be a multiple of 32 / bits-per-pixel. If this is not the case, then the Main Window Line Address Offset register must be programmed to a longer line which meets this requirement. This longer line creates a virtual image whose width is main window line address offset register x 32 / bits-per-pixel. In SwivelView 270, this virtual image should be drawn in display memory as left justified, and in SwivelView 90, this virtual image should be drawn in display memory as right justified. A left-justified image is one drawn in display memory such that each of the image's lines only use the left most portion of the line width defined by the line address offset register (i.e. starting at horizontal position 0). A right-justified image is one drawn in display memory such that each of the image's lines only use the right most portion of the line width defined by the line address offset register (i.e. starting at a non-zero horizontal position which is the virtual width image width). S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 37 8 Picture-In-Picture Plus Picture-in-Picture Plus (PIP+) enables a secondary window (or PIP+ window) within the main display window. The PIP+ window may be positioned anywhere within the virtual display and is controlled through the PIP+ Window control registers (REG[50h] through REG[5Ch]). The PIP+ window retains the same color depth and SwivelView orientation as the main window. A PIP+ window can be used to display temporary items such as a dialog box or to "float" the display item so that the system doesn't have to exclude the area during screen repaints. The following diagram shows an example of a PIP+ window within a main window. 0 SwivelView main-window PIP+ window Figure 8-1: Picture-in-Picture Plus with SwivelView disabled Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 38 Epson Research and Development Vancouver Design Center 8.1 Registers The following registers control the Picture-In-Picture Plus feature. Display Settings Register REG[10h] Default = 00000000h Pixel n/a Vertical 31 30 29 28 27 26 n/a 15 14 13 12 11 10 9 8 7 6 5 4 25 Pixel Display Blank 23 Dithering Disable 22 n/a Horiz. 24 21 Doubling Doubling SW Video Invert 20 PIP+ Window Enable n/a Read/Write SwivelView Mode Select 16 19 18 17 Bits-per-pixel Select (actual value: 1, 2, 4, 8 or 16 bpp) 3 2 1 0 PIP Window Enable The PIP+ Window Enable bit enables a PIP+ window within the main window. The location of the PIP+ window within the landscape window is determined by the PIP+ X Position register (REG[58h]) and PIP+ Y Position register (REG[5Ch]). The PIP+ window has its own Display Start Address register (REG[50h]) and Line Address Offset register (REG[54h]). The PIP+ window shares the same color depth and SwivelViewTM orientation as the main window. PIP+ Display Start Address Register REG[50h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 10 25 24 23 22 PIP+ Display Start Address bits 15-0 9 8 7 6 21 5 20 4 19 3 18 2 17 1 + Read/Write bit 16 16 0 PIP+ Display Start Address The PIP+ Display Start Address register is a DWORD which represents an address that points to the start of the PIP+ window image in the display buffer. An address of 0 is the start of the display buffer. For the following PIP+ descriptions, the desired byte address is the starting display address for the PIP+ window image. In SwivelView 0, program the start address = desired byte address / 4 In SwivelView 90, program the start address = ((desired byte address + (PIP+ width x bpp / 8) + ((4 - (PIP+ width x bpp / 8)) & 03h)) / 4) - 1 In SwivelView 180, program the start address = ((desired byte address + (PIP+ Stride x (PIP+ height - 1)) + (PIP+ width x bpp / 8) + ((4 - (PIP+ width x bpp / 8)) & 03h)) / 4) - 1 In SwivelView 270, program the start address = (desired byte address + ((PIP+ height - 1) x PIP+ Stride)) / 4 S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 39 Note Truncate all fractional values before writing to the address registers. Note SwivelView 0 and 180 require the PIP+ width to be a multiple of 32 / bits-per-pixel. SwivelView 90 and 270 require the PIP+ height to be a multiple of 32 / bits-per-pixel. If this is not possible, refer to Section 8.3, "Limitations" . PIP+ Line Address Offset Register REG[54h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 28 27 26 25 24 23 22 21 20 19 PIP+ Line Address Offset bits 9-0 6 5 4 3 18 2 Read/Write 17 1 16 0 PIP+ Line Address Offset The PIP+ Line Address Offset register indicates the number of dwords per line in the PIP+ window image. The image width must be a multiple of 32 / bpp. If the image width is not such a multiple, a slightly larger width must be chosen (see Section 8.3, "Limitations" ). PIP+ width and PIP+ height refer to the PIP+ dimensions as seen in SwivelView 0 (landscape mode). Stride is the number of bytes required for one line of the image; the offset register represents the stride in DWORD steps. PIP+ Stride = image width x bpp / 8 For SwivelView 0 and 180, PIP+ Width=((REG[58h] bits 25:16) - (REG[58h] bits 9:0) + 1) x (32 / bpp) PIP+ Height=(REG[5Ch] bits 25:16) - (REG[5Ch] bits 9:0) + 1 For SwivelView 90 and 270, PIP+ Width=((REG[5Ch] bits 25:16) - (REG[5Ch] bits 9:0) + 1) x (32 / bpp) PIP+ Height=(REG[58h] bits 25:16) - (REG[58h] bits 9:0) + 1 Note Image width can be larger than PIP+ width (or PIP+ height, for SwivelView 90 or 270). number of dwords per line = image width / (32 / bpp) Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 40 Epson Research and Development Vancouver Design Center PIP+ X Positions Register REG[58h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 28 27 26 25 24 23 PIP+ X End Position bits 9-0 22 21 20 19 PIP+ X Start Position bits 9-0 6 5 4 3 18 2 Read/Write 17 1 16 0 PIP+ X End Position The PIP+ X End Position bits determine the horizontal end of the PIP+ window in 0 and 180 SwivelView orientations. These bits determine the vertical end position in 90 and 270 SwivelView. For further information on defining the value of the X End Position, see Section 8.2, "Picture-In-Picture-Plus Examples" on page 45. This register also increments differently based on the SwivelView orientation. For 0 and 180 SwivelView the X End Position is incremented by X pixels where X is relative to the current color depth. For 90 and 270 SwivelView the X End Position is incremented in 1 line increments. Table 8-1: 32-bit Address Increments for PIP+ X Position in SwivelView 0 and 180 Bits-Per-Pixel (Color Depth) 1 bpp 2 bpp 4 bpp 8 bpp 16 bpp Pixel Increment (X) 32 16 8 4 2 In SwivelView 0, these bits set the horizontal coordinates (x) of the PIP+ window's right edge. Increasing x moves the right edge towards the right in steps of 32 / bits-per-pixel (see Table 8-1: ). The horizontal coordinates start at pixel 0. Program the PIP+ Window X End Position so that PIP+ Window X End Position = x / (32 / bits-per-pixel) Note Truncate the fractional part of the above equation. In SwivelView 90, these bits set the vertical coordinates (y) of the PIP+ window's bottom edge. Increasing y moves the bottom edge downward in 1 line steps. The vertical coordinates start at line 0. Program the PIP+ Window X End Position so that PIP+ Window X End Position = y S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 41 In SwivelView 180, these bits set the horizontal coordinates (x) of the PIP+ window's left edge. Increasing x moves the left edge towards the right in steps of 32 / bits-per-pixel (see Table 8-1: ). The horizontal coordinates start at pixel 0. Program the PIP+ Window X End Position so that PIP+ Window X End Position = (panel width - x - 1) / (32 / bits-per-pixel) Note Truncate the fractional part of the above equation. In SwivelView 270, these bits set the vertical coordinates (y) of the PIP+ window's top edge. Increasing y moves the top edge downwards in 1 line steps. The vertical coordinates start at line 0. Program the PIP+ Window X End Position so that PIP+ Window X End Position = panel width - y - 1 PIP+ X Start Position The PIP+ X Start Position bits determine the horizontal position of the start of the PIP+ window in 0 and 180 SwivelView orientations. These bits determine the vertical start position in 90 and 270 SwivelView. For further information on defining the value of the X Start Position, see Section 8.2, "Picture-In-Picture-Plus Examples" on page 45. The register also increments differently based on the SwivelView orientation. For 0 and 180 SwivelView the X Start Position is incremented by X pixels where X is relative to the current color depth. For 90 and 270 SwivelView the X Start Position is incremented in 1 line increments. Table 8-2: 32-bit Address Increments for Color Depth Bits-per-pixel (Color Depth) 1 bpp 2 bpp 4 bpp 8 bpp 16 bpp Pixel Increment (X) 32 16 8 4 2 In SwivelView 0, these bits set the horizontal coordinates (x) of the PIP+ windows's left edge. Increasing x moves the left edge towards the right in steps of (32 / bits-per-pixel) (see Table 8-2: ). The horizontal coordinates start at pixel 0. Program the PIP+ Window X Start Position so that PIP+ Window X Start Position = x / (32 / bits-per-pixel) Note Truncate the fractional part of the above equation. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 42 Epson Research and Development Vancouver Design Center In SwivelView 90, these bits set the vertical coordinates (y) of the PIP+ window's top edge. Increasing y moves the top edge downward in 1 line steps. The vertical coordinates start at line 0. Program the PIP+ Window X Start Position so that PIP+ Window X Start Position = y In SwivelView 180, these bits set the horizontal coordinates (x) of the PIP+ window's right edge. Increasing x moves the right edge towards the right in steps of (32 / bits-perpixel) (see Table 8-2: ). The horizontal coordinates start at pixel 0. Program the PIP+ Window X Start Position so that PIP+ Window X Start Position = (panel width - x - 1) / (32 / bits-per-pixel) Note Truncate the fractional part of the above equation. In SwivelView 270, these bits set the vertical coordinates (y) of the PIP+ window's bottom edge. Increasing y moves the bottom edge downwards in 1 line steps. The vertical coordinates start at line 0. Program the PIP+ Window X Start Position so that PIP+ Window X Start Position = panel width - y - 1 PIP+ Y Positions Register REG[5Ch] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 28 27 26 25 24 23 PIP Y End Position bits 9-0 22 21 20 19 PIP+ Y Start Position bits 9-0 6 5 4 3 18 2 17 1 16 0 + Read/Write PIP+ Y End Position The PIP+ Y End Position bits determine the vertical end position of the PIP+ window in 0 and 180 SwivelView orientations. These bits determine the horizontal end position in 90 and 270 SwivelView. For further information on defining the value of the Y End Position, see Section 8.2, "Picture-In-Picture-Plus Examples" on page 45. The register also increments differently based on the SwivelView orientation. For 0 and 180 SwivelView the Y End Position is incremented in 1 line increments. For 90 and 270 SwivelView the Y End Position is incremented by Y pixels where Y is relative to the current color depth. Table 8-3: 32-bit Address Increments for Color Depth Bits-Per-Pixel (Color Depth) 1 bpp 2 bpp 4 bpp 8 bpp 16 bpp Pixel Increment (Y) 32 16 8 4 2 S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 43 In SwivelView 0, these bits set the vertical coordinates (y) of the PIP+ windows's bottom edge. Increasing y moves the bottom edge downwards in 1 line steps. The vertical coordinates start at line 0. Program the PIP+ Window Y End Position so that PIP+ Window Y End Position = y In SwivelView 90, these bits set the horizontal coordinates (x) of the PIP+ window's left edge. Increasing x moves the left edge towards the right in steps of (32 / bits-per-pixel) (see Table 8-3: ). The horizontal coordinates start at pixel 0. Program the PIP+ Window Y End Position so that PIP+ Window Y End Position = (panel height - x - 1) / (32 / bits-per-pixel) Note Truncate the fractional part of the above equation. In SwivelView 180, these bits set the vertical coordinates (y) of the PIP+ window's top edge. Increasing y moves the top edge downwards in 1 line steps. The vertical coordinates start at line 0. Program the PIP+ Window Y End Position so that PIP+ Window Y End Position = panel height - y - 1 In SwivelView 270, these bits set the horizontal coordinates (x) of the PIP+ window's right edge. Increasing x moves the right edge towards the right in steps of (32 / bits-perpixel) (see Table 8-3: ). The horizontal coordinates start at pixel 0. Program the PIP+ Window Y End Position so that PIP+ Window Y End Position = x / (32 / bits-per-pixel) Note Truncate the fractional part of the above equation. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 44 Epson Research and Development Vancouver Design Center PIP+ Y Start Position The PIP+ Y Start Position bits determine the vertical start position of the PIP+ window in 0 and 180 SwivelView orientations. These bits determine the horizontal start position in 90 and 270 SwivelView. For further information on defining the value of the Y Start Position, see Section 8.2, "Picture-In-Picture-Plus Examples" on page 45. The register also increments differently based on the SwivelView orientation. For 0 and 180 SwivelView the Y Start Position is incremented in 1 line increments. For 90 and 270 SwivelView the Y Start Position is incremented by Y pixels where Y is relative to the current color depth. Table 8-4: 32-bit Address Increments for Color Depth Bits-Per-Pixel (Color Depth) 1 bpp 2 bpp 4 bpp 8 bpp 16 bpp Pixel Increment (Y) 32 16 8 4 2 In SwivelView 0, these bits set the vertical coordinates (y) of the PIP+ windows's top edge. Increasing y moves the top edge downwards in 1 line steps. The vertical coordinates start at line 0. Program the PIP+ Window Y Start Position so that PIP+ Window Y Start Position = y In SwivelView 90, these bits set the horizontal coordinates (x) of the PIP+ window's right edge. Increasing x moves the right edge towards the right in steps of (32 / bits-per-pixel) (see Table 8-4: ). The horizontal coordinates start at pixel 0. Program the PIP+ Window Y Start Position so that PIP+ Window Y Start Position = (panel height - x - 1) / (32 / bits-per-pixel) Note Truncate the fractional part of the above equation. In SwivelView 180, these bits set the vertical coordinates (y) of the PIP+ window's bottom edge. Increasing y moves the bottom edge downwards in 1 line steps. The vertical coordinates start at line 0. Program the PIP+ Window Y Start Position so that PIP+ Window Y Start Position = panel height - y - 1 S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 45 In SwivelView 270, these bits set the horizontal coordinates (x) of the PIP+ window's left edge. Increasing x moves the left edge towards the right in steps of (32 / bits-per-pixel) (see Table 8-4: ). The horizontal coordinates start at pixel 0. Program the PIP+ Window Y Start Position so that PIP+ Window Y Start Position = x / (32 / bits-per-pixel) Note Truncate the fractional part of the above equation. 8.2 Picture-In-Picture-Plus Examples 8.2.1 SwivelView 0 (Landscape Mode) 0 SwivelViewTM panel's origin PIP+ window y start position (REG[5Ch] bits 9-0) PIP+ window y end position (REG[5Ch] bits 25-16) main-window PIP+ window PIP+ window x start position (REG[58h] bits 9-0) PIP+ window x end position (REG[58h] bits 25-16) Figure 8-2: Picture-in-Picture Plus with SwivelView disabled SwivelView 0 (or landscape) is a mode in which both the main and PIP+ window are nonrotated. The images for each window are typically placed consecutively, with the main window image starting at address 0 and followed by the PIP+ window image. In addition, both images must start at addresses which are dword-aligned (the last two bits of the starting address must be 0). Note It is possible to use the same image for both the main window and PIP+ window. To do so, set the PIP+ Line Address Offset register (REG[54h]) to the same value as the Main Window Line Address Offset register (REG[44h]. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 46 Epson Research and Development Vancouver Design Center Example 5: Program the PIP+ window registers for a 320x240 panel at 4 bpp, with the PIP+ window positioned at (80, 60) with a width of 160 and a height of 120. 1. Determine the value for the PIP+ Window X Positions and PIP+ Window Y Positions registers. Let the top left corner of the PIP+ window be (x1, y1), and let the bottom right corner be (x2, y2), where x2 = x1 + width - 1 and y2 = y1 + height - 1. The PIP+ Window X Positions register sets the horizontal coordinates of the PIP+ window's top left and bottom right corners. The PIP+ Window Y Positions register sets the vertical coordinates of the PIP+ window's top left and bottom right corners. The required values are calculated as follows: X Start Position = x1 / (32 / bpp) = 80 / (32 / 4) = 10 = 0Ah Y Start Position = y1 = 60 = 3Ch X End Position = x2 / (32 / bpp) = (80 + 160 - 1) / (32 / 4) = 29.875 = 1Dh (truncated fractional part) Y End Position = y2 = 60 + 120 - 1 = 179 = B3h S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 47 2. Program the PIP+ Window X Positions register with the X Start Position in bits 9-0 and the X End Position in bits 25-16. REG[58h] is set to 001D000Ah. Program the PIP+ Window Y Positions register with the Y Start Position in bits 9-0 and the Y End Position in bits 25-16. REG[5Ch] is set to 00B3003Ch. Due to truncation, the dimensions of the PIP+ window may have changed. Recalculate the PIP+ window width and height below: PIP+ Width = ((REG[58h] bits 25:16) - (REG[58h] bits 9:0) + 1) x (32 / bpp) = (1Dh - 0Ah + 1) x (32 / 4) = 160 pixels PIP Height = (REG[5Ch] bits 25:16) - (REG[5Ch] bits 9:0) + 1 = B3h - 3Ch + 1 = 120 lines 3. Determine the PIP+ display start address. The main window image must take up 320 x 240 pixels x bpp / 8 = 9600h bytes. If the main window starts at address 0h, the PIP+ window can start at 9600h. PIP+ display start address = desired byte address / 4 = 9600h / 4 = 2580h. Program the PIP+ Display Start Address register. REG[50h] is set to 00002580h. 4. Determine the PIP+ line address offset. number of dwords per line = image width / (32 / bpp) = 160 / (32 / 4) = 20 = 14h Program the PIP+ Line Address Offset register. REG[54h] is set to 00000014h. 5. Enable the PIP+ window. Program the PIP+ Window Enable bit. REG[10h] bit 19 is set to 1. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 48 Epson Research and Development Vancouver Design Center 8.2.2 SwivelView 90 90 SwivelViewTM PIP+ window x end position (REG[58h] bits 25-16) PIP+ window panel's origin PIP+ window x start position (REG[58h] bits 9-0) PIP+ window y start position (REG[5Ch] bits 9-0) main-window PIP+ window y end position (REG[5Ch] bits 25-16) Figure 8-3: Picture-in-Picture Plus with SwivelView 90 enabled SwivelView 90 is a mode in which both the main and PIP+ windows are rotated 90 counter-clockwise when shown on the panel. The images for each window are typically placed consecutively, with the main window image starting at address 0 and followed by the PIP+ window image. In addition, both images must start at addresses which are dwordaligned (the last two bits of the starting address must be 0). Note It is possible to use the same image for both the main window and PIP+ window. To do so, set the PIP+ Line Address Offset register (REG[54h]) to the same value as the Main Window Line Address Offset register (REG[44h]). S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 49 Example 6: In SwivelView 90, program the PIP+ window registers for a 320x240 panel at 4 bpp, with the PIP+ window positioned at SwivelView 90 coordinates (60, 80) with a width of 120 and a height of 160. 1. Determine the value for the PIP+ Window X Positions and PIP+ Window Y Positions registers. Let the top left corner of the PIP+ window be (x1, y1), and let the bottom right corner be (x2, y2), where x2 = x1 + width - 1 and y2 = y1 + height - 1. The PIP+ Window X Positions register sets the vertical coordinates of the PIP+ window's top right and bottom left corners. The PIP+ Window Y Positions register sets the horizontal coordinates of the PIP+ window's top right and bottom left corners. The required values are calculated as follows: X Start Position = y1 = 80 = 50h Y Start Position = (panel height - x2 - 1) / (32 / bpp) = (240 - (60 + 120 - 1) - 1) / (32 / 4) = 7.5 = 07h (truncated fractional part) X End Position = y2 = 80 + 160 - 1 = 239 = EFh Y End Position = (panel height - x1 - 1) / (32 / bpp) = (240 - 60 - 1) / (32 / 4) = 22.375 = 16h (truncated fractional part) Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 50 Epson Research and Development Vancouver Design Center 2. Program the PIP+ Window X Positions register with the X Start Position in bits 9-0 and the X End Position in bits 25-16. REG[58h] is set to 00EF0050h. Program the PIP+ Window Y Positions register with the Y Start Position in bits 9-0 and the Y End Position in bits 25-16. REG[5Ch] is set to 00160007h. Due to truncation, the dimensions of the PIP+ window may have changed. Recalculate the PIP+ window width and height below: PIP+ Width = ((REG[5Ch] bits 25:16) - (REG[5Ch] bits 9:0) + 1) x (32 / bpp) = (16h - 07h + 1) x (32 / 4) = 128 pixels (note that this is different from the desired width) PIP Height = (REG[58h] bits 25:16) - (REG[58h] bits 9:0) + 1 = EFh - 50h + 1 = 160 lines 3. Determine the PIP+ display start address. The main window image must take up 320 x 240 pixels x bpp / 8 = 9600h bytes. If the main window starts at address 0h, then the PIP+ window can start at 9600h. PIP+ display start address = ((desired byte address + (PIP+ width x bpp / 8) + ((4 - (PIP+ width x bpp / 8)) & 03h)) / 4) - 1 = ((9600h + (128 x 4 / 8) + ((4 - (128 x 4 / 8)) & 03h)) / 4) - 1 = 9615 = 258Fh Program the PIP+ Display Start Address register. REG[50h] is set to 0000258Fh. 4. Determine the PIP+ line address offset. number of dwords per line = image width / (32 / bpp) = 128 / (32 / 4) = 16 = 10h Program the PIP+ Line Address Offset register. REG[54h] is set to 00000010h. 5. Enable the PIP+ window. Program the PIP+ Window Enable bit. REG[10h] bit 19 is set to 1. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 51 8.2.3 SwivelView 180 180 SwivelViewTM PIP+ window x end position (REG[58h] bits 25-16) PIP+ window x start position (REG[58h] bits 9-0) PIP+ window main-window PIP+ window y end position (REG[58h] bits 25-16) PIP+ window y start position (REG[5Ch] bits 9-0) panel's origin Figure 8-4: Picture-in-Picture Plus with SwivelView 180 enabled SwivelView 180 is a mode in which both the main and PIP+ windows are rotated 180 counter-clockwise when shown on the panel. The images for each window are typically placed consecutively, with the main window image starting at address 0 and followed by the PIP+ window image. In addition, both images must start at addresses which are dwordaligned (the last two bits of the starting address must be 0). Note It is possible to use the same image for both the main window and PIP+ window. To do so, set the PIP+ Line Address Offset register (REG[54h]) to the same value as the Main Window Line Address Offset register (REG[44h]). Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 52 Epson Research and Development Vancouver Design Center Example 7: In SwivelView 180, program the PIP+ window registers for a 320x240 panel at 4 bpp, with the PIP+ window positioned at SwivelView 180 coordinates (80, 60) with a width of 160 and a height of 120. 1. Determine the value for the PIP+ Window X Positions and PIP+ Window Y Positions registers. Let the top left corner of the PIP+ window be (x1, y1), and let the bottom right corner be (x2, y2), where x2 = x1 + width - 1 and y2 = y1 + height - 1. The PIP+ Window X Positions register sets the horizontal coordinates of the PIP+ window's bottom right and top left corner. The PIP+ Window Y Positions register sets the vertical coordinates of the PIP+ window's bottom right and top left corner. The required values are calculated as follows: X Start Position = (panel width - x2 - 1) / (32 / bpp) = (320 - (80 + 160 - 1) - 1) / (32 / 4) = 10 = 0Ah Y Start Position = panel height - y2 - 1 = 240 - (60 + 120 - 1) - 1 = 60 = 3Ch X End Position = (panel width - x1 - 1) / (32 / bpp) = (320 - 80 - 1) / (32 / 4) = 29.875 = 1Dh (truncated fractional part) Y End Position = panel height - y1 - 1 = 240 - 60 - 1 = 179 = B3h S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 53 Program the PIP+ Window X Positions register with the X Start Position in bits 9-0 and the X End Position in bits 25-16. REG[58h] is set to 001D000Ah. Program the PIP+ Window Y Positions register with the Y Start Position in bits 9-0 and the Y End Position in bits 25-16. REG[5Ch] is set to 00B3003Ch. Due to truncation, the dimensions of the PIP+ window may have changed. Recalculate the PIP+ window width and height below: PIP+ Width = ((REG[58h] bits 25:16) - (REG[58h] bits 9:0) + 1) x (32 / bpp) = (1Dh - 0Ah + 1) x (32 / 4) = 160 pixels PIP Height = (REG[5Ch] bits 25:16) - (REG[5Ch] bits 9:0) + 1 = B3h - 3Ch + 1 = 120 lines 2. Determine the PIP+ display start address. The main window image must take up 320 x 240 pixels x bpp / 8 = 9600h bytes. If the main window starts at address 0h, then the PIP+ window can start at 9600h. PIP+ Stride = image width x bpp / 8 = 160 x 4 / 8 = 80 = 50h PIP+ display start address = ((desired byte address + (PIP+ Stride x (PIP+ height - 1)) + (PIP+ width x bpp / 8) + ((4 - (PIP width x bpp / 8)) & 03h)) / 4) - 1 = ((9600h + (80 x (120 - 1)) + (160 x 4 / 8) + ((4 - (160 x 4 / 8))&03h)) / 4) - 1 = 11999 = 2EDFh Program the PIP+ Display Start Address register. REG[50h] is set to 00002EDFh. 3. Determine the PIP+ line address offset. number of dwords per line = image width / (32 / bpp) = 160 / (32 / 4) = 20 = 14h Program the PIP+ Line Address Offset register. REG[54h] is set to 00000014h. 4. Enable the PIP+ window. Program the PIP+ Window Enable bit. REG[10h] bit 19 is set to 1. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 54 Epson Research and Development Vancouver Design Center 8.2.4 SwivelView 270 270 SwivelViewTM PIP+ window y end position (REG[5Ch] bits 25-16) main-window PIP+ window y start position (REG[5Ch] bits 9-0) PIP+ window PIP+ window x start position (REG[58h] bits 9-0) panel's origin PIP+ window x end position (REG[58h] bits 25-16) Figure 8-5: Picture-in-Picture Plus with SwivelView 270 enabled SwivelView 270 is a mode in which both the main and PIP+ windows are rotated 270 counter-clockwise when shown on the panel. The images for each window are typically placed consecutively, with the main window image starting at address 0 and followed by the PIP+ window image. In addition, both images must start at addresses which are dwordaligned (the last two bits of the starting address must be 0). Note It is possible to use the same image for both the main window and PIP+ window. To do so, set the PIP+ Line Address Offset register (REG[54h]) to the same value as the Main Window Line Address Offset register (REG[44h]). S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 55 Example 8: In SwivelView 270, program the PIP+ window registers for a 320x240 panel at 4 bpp, with the PIP+ window positioned at SwivelView 270 coordinates (60, 80) with a width of 120 and a height of 160. 1. Determine the value for the PIP+ Window X Positions and PIP+ Window Y Positions registers. Let the top left corner of the PIP+ window be (x1, y1), and let the bottom right corner be (x2, y2), where x2 = x1 + width - 1 and y2 = y1 + height - 1. The PIP+ Window X Positions register sets the vertical coordinates of the PIP+ window's top right and bottom left corner. The PIP+ Window Y Positions register sets the horizontal coordinates of the PIP+ window's top right and bottom left corner. The required values are calculated as follows: X Start Position = panel width - y2 - 1 = 320 - (80 + 160 - 1) - 1 = 80 = 50h Y Start Position = x1 / (32 / bpp) = 60 / (32 / 4) = 7.5 = 07h (truncated fractional part) X End Position = panel width - y1 - 1 = 320 - 80 - 1 = 239 = EFh Y End Position = x2 / (32 / bpp) = (60 + 120 - 1) / (32 / 4) = 22.375 = 16h (truncated fractional part) Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 56 Epson Research and Development Vancouver Design Center 2. Program the PIP+ Window X Positions register with the X Start Position in bits 9-0 and the X End Position in bits 25-16. REG[58h] is set to 00EF0050h. Program the PIP+ Window Y Positions register with the Y Start Position in bits 9-0 and the Y End Position in bits 25-16. REG[5Ch] is set to 00160007h. Due to truncation, the dimensions of the PIP+ window may have changed. Recalculate the PIP+ window width and height below: PIP+ Width = ((REG[5Ch] bits 25:16) - (REG[5Ch] bits 9:0) + 1) x (32 / bpp) = (16h - 07h + 1) x (32 / 4) = 128 pixels (note that this is different from the desired width) PIP Height = (REG[58h] bits 25:16) - (REG[58h] bits 9:0) + 1 = EFh - 50h + 1 = 160 lines 3. Determine the PIP+ display start address. The main window image must take up 320 x 240 pixels x bpp / 8 = 9600h bytes. If the main window starts at address 0h, then the PIP+ window can start at 9600h. PIP+ Stride = image width x bpp / 8 = 128 x 4 / 8 = 64 = 40h PIP+ display start address = (desired byte address + ((PIP+ height - 1) x PIP+ Stride)) / 4 = (9600h + ((160 - 1) x 64)) / 4 = 12144 = 2F70h Program the PIP+ Display Start Address register. REG[50h] is set to 00002F70h. 4. Determine the PIP+ line address offset. number of dwords per line = image width / (32 / bpp) = 128 / (32 / 4) = 16 = 10h Program the PIP+ Line Address Offset register. REG[54h] is set to 00000010h. 5. Enable the PIP+ window. Program the PIP+ Window Enable bit. REG[10h] bit 19 is set to 1. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 57 8.3 Limitations 8.3.1 SwivelView 0 and 180 The PIP+ Line Address Offset register (REG[54h]) requires the PIP+ window image width to be a multiple of 32 / bits-per-pixel. If this formula is not satisfied, then the PIP+ Line Address Offset register must be programmed to the next larger value that satisfies the formula. 8.3.2 SwivelView 90 and 270 The PIP+ Line Address Offset register (REG[54h]) requires the PIP+ window image width to be a multiple of 32 / bits-per-pixel. If this formula is not satisfied, then the PIP+ Line Address Offset register must be programmed to the next larger value that satisfies the formula. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 58 Epson Research and Development Vancouver Design Center 9 2D BitBLT Engine BitBLT is an acronym for Bit Block Transfer. The 2D BitBLT Engine in the S1D13A04 is designed to increase the speed of the most common GUI operations by off-loading work from the CPU, reducing traffic on the system bus and freeing the CPU sooner for other tasks. BitBLTs require a destination - a place to write the display data. Most BitBLTs have a source of data for the BitBLT and many also incorporate a pattern. The pattern, source, and destination operands are combined using logical AND, OR, XOR and NOT operations. The combining process is called a Raster Operation (ROP) and results in the final pixel data to be written to the destination address. The S1D13A04 2D BitBLT engine supports a total of sixteen ROPs and works at 8 bpp and 16 bpp color depths. This section describes the BitBLT registers and provides some sample BitBLT operations. 9.1 Registers The S1D13A04 BitBLT registers are located 8000h bytes from the start of S1D13A04 address space. The registers are labelled, according to their byte offset, as REG[8000h] through REG[8024h]. The following is a description of all BitBLT registers. BitBLT Control Register REG[8000h] Default = 00000000h n/a 31 30 29 28 27 26 25 24 n/a 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 23 22 21 20 19 Color Format Select 18 Read/Write Dest Linear Select 17 Source Linear Select 16 BitBLT Enable (WO) 0 Color Format Select The Color Format Select bit indicates to the BitBLT engine what color depth to assume for the BitBLT operation. The BitBLT engine uses this information to set the step size for internal counters. When this bit = 0, 8 bpp is selected and when this bit = 1, 16 bpp is selected. Destination Linear Select The Destination Linear Select bit determines how the BitBLT destination address pointer is updated when the BitBLT reaches the end of a row. When the end of a row is reached and rectangular is selected the destination address is updated to point to the beginning of the next row of a rectangular area. The offset to the start of the next row is contained in the BitBLT Memory Address Offset register (REG[8014h]). S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 59 When the end of a row is reached and destination linear is selected the destination address is updated to the next available memory offset. The result is data which is jammed together with one row immediately following the next in display memory. This is useful when it is desired to compactly save a rectangular area into off screen memory. When this bit = 0, the BitBLT destination is stored as a rectangular region of memory. When this bit = 1, the BitBLT destination is stored as a contiguous linear block of memory. Source Linear Select The Source Linear Select bit determines how the source address pointer is updated when the BitBLT reaches the end of a row. When the end of a row is reached and rectangular is selected the source address is updated to point to the beginning of the next row of a rectangular area. The offset to the start of the next row is contained in the BitBLT Memory Address Offset register (REG[8014h]). When the end of a row is reached and source linear is selected the source address is updated to the next available memory offset. The result is data, which was jammed together with one row immediately following the next in display memory, can now be expanded back to a rectangular area. When this bit = 0, the BitBLT source is stored as a rectangular region of memory. When this bit = 1, the BitBLT source is stored as a contiguous linear block of memory. BitBLT Enable This bit is write only. Setting this bit to 1 begins the 2D BitBLT operation. This bit must not be set to 0 while a BitBLT operation is in progress. Note To determine the status of a BitBLT operation use the BitBLT Busy Status bit (REG[8004h] bit 0). Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 60 Epson Research and Development Vancouver Design Center BitBLT Status Register REG[8004h] Default = 00000000h n/a 31 30 29 28 Number of Used FIFO Entries 27 n/a 15 14 13 12 11 10 9 8 7 26 25 24 23 n/a 22 FIFO Not Empty 6 21 FIFO Half Full 5 20 FIFO Full Status 4 19 18 n/a 3 2 Read Only Number of Free FIFO Entries (0 means full) 17 16 BitBLT Busy Status 0 1 Number of Used FIFO Entries This is a read-only status. This field indicates the minimum number of FIFO entries currently in use (there may be more in the internal pipeline). If these bits return a 0, the FIFO is empty. Number of Free FIFO Entries This is a read-only status bit This field indicates the number of empty FIFO entries available. If these bits return a 0, the FIFO is full. FIFO Not-Empty This is a read-only status bit. When this bit = 0, the BitBLT FIFO is empty. When this bit = 1, the BitBLT FiFO has at least one data. To reduce system latency, software can monitor this bit prior to a BitBLT read burst operation. The following table shows the number of words available in the BitBLT FIFO under different status conditions. Table 9-1: BitBLT FIFO Words Available BitBLT FIFO Not Number of Words BitBLT FIFO Half BitBLT FIFO Full available in BitBLT Empty Status Full Status Status FIFO (REG[8004h] Bit 4) (REG[8004h] Bit 5) (REG[8004h] Bit 6) 0 0 0 1 0 0 1 1 0 1 1 1 0 1 to 6 7 to 14 15 to 16 BitBLT FIFO Half Full Status This is a read-only status bit. When this bit = 1, the BitBLT FIFO is half full or greater than half full. When this bit = 0, the BitBLT FIFO is less than half full. BitBLT FIFO Full Status This is a read-only status bit. When this bit = 1, the BitBLT FIFO is full. When this bit = 0, the BitBLT FIFO is not full. BitBLT Busy Status This bit is a read-only status bit. When this bit = 1, the BitBLT operation is in progress. When this bit = 0, the BitBLT operation is complete. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 61 Note During a BitBLT Read operation, the BitBLT engine does not attempt to keep the FIFO full. If the FIFO becomes full, the BitBLT operation stops temporarily as data is read out of the FIFO. The BitBLT will restart only when less than 14 values remain in the FIFO. BitBLT Command Register REG[8008h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 n/a 10 9 8 7 6 5 4 3 25 24 23 22 21 20 19 Read/Write BitBLT ROP Code bits 3-0 18 17 16 BitBLT Operation bits 3-0 2 1 0 BitBLT ROP Code The BitBLT ROP Code specifies the Raster Operation to be used for Write and Move BitBLTs. In addition, for Color Expansion, the BitBLT ROP Code bits 2-0 specify the start bit position for Color Expansion BitBLTs. Table 9-2 : BitBLT ROP Code/Color Expansion Function Selection BitBLT ROP Code Bits [3:0] 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 Boolean Function for Write BitBLT and Move BitBLT 0 (Blackness) ~S . ~D or ~(S + D) ~S . D ~S S . ~D ~D S^D ~S + ~D or ~(S . D) S.D ~(S ^ D) D ~S + D S S + ~D S+D 1 (Whiteness) Boolean Function for Pattern Fill 0 (Blackness) ~P . ~D or ~(P + D) ~P . D ~P P . ~D ~D P^D ~P + ~D or ~(P . D) P.D ~(P ^ D) D ~P + D P P + ~D P+D 1 (Whiteness) Start Bit Position for Color Expansion bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 bit 0 bit 1 bit 2 bit 3 bit 4 bit 5 bit 6 bit 7 Note S = Source, D = Destination, P = Pattern. ~ = NOT, . = Logical AND, + = Logical OR, ^ = Logical XOR Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 62 Epson Research and Development Vancouver Design Center BitBLT Operation The BitBLT Operation selects which BitBLT operation performed. The following table lists the available BitBLT operations. Table 9-3 : BitBLT Operation Selection BitBLT Operation Bits [3:0] 0000 0001 0010 0011 Write BitBLT with ROP This operation refers to BitBLTs where data is to be transferred from system memory to display memory Read BitBLT This operation refers to BitBLTs where data is to be transferred from display memory to system memory Move BitBLT in positive direction with ROP This operation is used to transfer data from display memory to display memory Move BitBLT in negative direction with ROP This operation is used to transfer data from display memory to display memory Transparent Write BitBLT 0100 Like the Write BitBLT this operation is used when transferring data from system memory to display memory, the difference is that destination pixels will be left "as is" when source pixels of a specified color are encountered. Transparent Move BitBLT in positive direction 0101 As with the Move BitBLTs this operation is used to transfer data from display memory to display memory. The difference is that destination pixels will be left "as is" when source pixels of a specified color are encountered. Pattern Fill with ROP Fills the specified area of display memory with a repeating pattern stored in display memory. Pattern Fill with transparency 0111 As with the Pattern Fill, this BitBLT fills a specified area of display memory with a repeating pattern, destination pixels will be left "as is" when source pixels of a specified color are encountered. Color Expansion 1000 This BitBLT expands the bits of the source data into full pixels at the destination. If a source bit is 0 the destination pixel will be background color and if the source bit is 1 the destination pixel will be of foreground color. The source data for Color Expansion BitBLTs is always system memory. Color Expansion with transparency 1001 Like the Color Expansion BitBLT, this operations expands each bit of the source data to occupy a full destination pixel. The difference, is that destination pixels corresponding to source bits of 0 will be left "as is". The data source is system memory Move BitBLT with Color Expansion 1010 This BitBLT works the same as the Color Expansion BitBLT however the source of the BitBLT is display memory. Move BitBLT with Color Expansion and transparency 1011 This BitBLT works the same as the Color Expansion with Transparency BitBLT however the source of the BitBLT is display memory. Solid Fill BitBLT 1100 Use this BitBLT to fill a given area with one solid color. Other combinations Reserved BitBLT Operation 0110 S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 63 BitBLT Source Start Address Register REG[800Ch] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 10 25 24 23 22 BitBLT Source Start Address bits 15-0 9 8 7 6 21 5 20 4 19 3 18 2 Read/Write BitBLT Source Start Address bits 20-16 17 1 16 0 BitBLT Source Start Address This register has multiple meanings depending on the BitBLT operation it specifies. It can be either: * the start address in display memory of the source data for BitBLTs where the source is display memory (i.e. Move BitBLTs). * in pattern fill operations, the BitBLT Source Start Address determines where in the pattern to begin the BitBLT operation and is defined by the following equation: Value programmed to the Source Start Address Register = Pattern Base Address + Pattern Line Offset + Pixel Offset. * the data alignment for 16 bpp BitBLTs where the source of BitBLT data is the CPU (i.e. Write BitBLTs). The following table shows how Source Start Address Register is defined for 8 and 16 bpp color depths. Table 9-4 : BitBLT Source Start Address Selection Color Format 8 bpp 16 bpp Pattern Base Address[20:0] BitBLT Source Start Address[20:6] BitBLT Source Start Address[20:7] Pattern Line Offset[2:0] BitBLT Source Start Address[5:3] BitBLT Source Start Address[6:4] Pixel Offset[3:0] BitBLT Source Start Address[2:0] BitBLT Source Start Address[3:0] BitBLT Destination Start Address Register REG[8010h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 10 25 24 23 22 BitBLT Destination Start Address bits 15-0 9 8 7 6 21 5 20 4 19 3 18 2 Read/Write BitBLT Destination Start Address bits 20-16 17 1 16 0 BitBLT Destination Start Address This register specifies the initial destination address for BitBLT operations. For rectangular destinations this address represents the upper left corner of the BitBLT rectangle. If the operation is a Move BitBLT in a Negative Direction, these bits define the address of the lower right corner of the rectangle. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 64 Epson Research and Development Vancouver Design Center BitBLT Memory Address Offset Register REG[8014h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 28 12 27 11 26 10 25 9 24 8 23 22 21 20 19 BitBLT Memory Address Offset bits 10-0 7 6 5 4 3 18 2 Read/Write 17 1 16 0 BitBLT Memory Address Offset This register specifies the 11-bit address offset from the starting word of line n to the starting word of line n + 1. The offset value is only used for address calculation when the BitBLT is configured as rectangular. BitBLT Width Register REG[8018h] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 6 28 27 26 25 24 23 22 21 20 BitBLT Width bits 9-0 5 4 19 3 18 2 17 1 16 0 Read/Write BitBLT Width This register specifies the width of a BitBLT in pixels - 1. BitBLT width (in pixels) = REG[8018h] + 1 BitBLT Height Register REG[801Ch] Default = 00000000h n/a 31 15 30 14 29 n/a 13 12 11 10 9 8 7 6 28 27 26 25 24 23 22 21 20 BitBLT Height bits 9-0 5 4 19 3 18 2 17 1 16 0 Read/Write BitBLT Height This register specifies the height of the BitBLT in lines - 1. BitBLT height (in lines) = REG[801Ch] + 1 S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 65 BitBLT Background Color Register REG[8020h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 10 25 24 23 22 BitBLT Background Color bits 15-0 9 8 7 6 21 5 20 4 19 3 18 2 Read/Write 17 1 16 0 BitBLT Background Color This register specifies either: * the BitBLT background color for Color Expansion or * the key color for Transparent BitBLT. For 8 bpp BitBLTs, bits 7-0 are used to specify the key color and for 16 bpp BitBLTs, bits 15-0 are used. BitBLT Foreground Color Register REG[8024h] Default = 00000000h n/a 31 15 30 14 29 13 28 12 27 11 26 10 25 24 23 22 BitBLT Foreground Color bits 15-0 9 8 7 6 21 5 20 4 19 3 18 2 17 1 16 0 Read/Write BitBLT Foreground Color This register specifies the foreground color for Color Expansion or Solid Fill BitBLTs. For 8 bpp BitBLTs, bits 7-0 are used to specify the color and for 16 bpp BitBLTs, bits 15-0 are used. 2D Accelerator (BitBLT) Data Memory Mapped Region Register AB16-AB0 = 10000h-1FFFEh, even addresses BitBLT Data bits 31-16 31 15 30 14 29 13 28 12 27 11 26 10 25 9 24 23 BitBLT Data bits 15-0 8 7 22 6 21 5 20 4 19 3 18 2 17 1 16 0 Read/Write BitBLT Data bits This register is used by the local CPU to send data to the BitBLT engine for Write and Color Expansion BitBLTs and is used to read data from the BitBLT engine for Read BitBLTs. The register should be treated as any other register it is however loosely decoded from 10000h to 1FFFEh. Note The BitBLT data registers are 32 bits wide but are accessed on WORD boundaries using 16 bit accesses. Byte access to the BitBLT data registers is not allowed. Note Accesses to this register, other than for purposes of a BitBLT operation may cause the 13A04 to stop responding and the system to hang. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 66 Epson Research and Development Vancouver Design Center 9.2 BitBLT Descriptions The S1D13A04 supports 13 fundamental BitBLT operations: * Write BitBLT with ROP * Read BitBLT * Move BitBLT in positive direction with ROP * Move BitBLT in negative direction with ROP * Transparent Write BitBLT * Transparent Move BitBLT in positive direction * Pattern Fill with ROP * Pattern Fill with Transparency * Color Expansion * Color Expansion with Transparency * Move BitBLT with Color Expansion * Move BitBLT with Color Expansion and Transparency * Solid Fill Most of the 13 operations are self completing. This means once the BitBLT operation begins it completes without further assistance from the local CPU. No data transfers are required to or from the local CPU. Five BitBLT operations (Write BitBLT with ROP, Transparent Write BitBLT, Color Expansion, Color Expansion with Transparency, Read BitBLT) require data to be written to/read from the BitBLT engine. This data must be transferred one word (16-bits) at a time. This does not imply only 16-bit CPU instructions are acceptable. If a system is able to separate one DWORD write into two WORD writes and the CPU writes the low word before the high word, then 32-bit CPU instructions are acceptable. Otherwise, 16-bit CPU instructions are required. The data is not directly written to/read from the display buffer. It is written to/read from the BitBLT FIFO through the 64K byte BitBLT aperture specified at the address of REG[10000h]. The 16 word FIFO can be written to only when not full and can be read from only when not empty. Failing to monitor the FIFO status can result in a BitBLT FIFO overflow or underflow. While the FIFO is being written to by the CPU, it is also being emptied by the S1D13A04. If the S1D13A04 empties the FIFO faster than the CPU can fill it, it may not be possible to cause an overflow/underflow. In these cases, performance can be improved by not monitoring the FIFO status. However, this is very much platform dependent and must be determined for each system. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 67 9.2.1 Write BitBLT with ROP Write BitBLTs increase the speed of transferring data from system memory to the display buffer. The Write BitBLT with ROP accepts data from the CPU and writes it into display memory. This BitBLT is typically used to copy a bitmap image from system memory to the display buffer. Write BitBLTs support 16 ROPs, the most frequently used being ROP 0Ch (Copy Source to Destination). Write BitBLTs support both rectangular and linear destinations. Using a linear destination it is possible to move an image to off screen memory in a compact format for later restoration using a Move BitBLT. During a Write BitBLT operation the BitBLT engine expects to receive a particular number of WORDs and it is the responsibility of the CPU to provide the required amount of data. When performing BitBLT at 16 bpp color depth the number of WORDS to be sent is the same as the number of pixels to be transferred as each pixel is one WORD wide. The number of WORD writes the BitBLT engine expects is calculated using the following formula. WORDS = Pixels = BitBLTWidth x BitBLTHeight When the color depth is 8 bpp the formula must take into consideration that the BitBLT engine accepts only WORD accesses and each pixel is one BYTE. This may lead to a different number of WORD transfers than there are pixels to transfer. The number of WORD accesses is dependant on the position of the first pixel within the first WORD of each row. Is the pixel stored in the low byte or the high byte of the WORD? This aspect of the BitBLT is called phase and is determined as follows: Source phase is 0 when the first pixel is in the low byte and the second pixel is in the high byte of the WORD. When the source phase is 0, bit 0 of the Source Start Address Register is 0. The Source Phase is 1 if the first pixel of each row is contained in the high byte of the WORD, the contents of the low byte are ignored. When the source phase is 1, bit 0 of the Source Start Address Register is set. Depending on the Source Phase and the BitBLT Width, the last WORD may contain only one pixel. In this case it is always in the low byte. The number of WORD writes the BitBLT engine expects for 8 bpp color depths is shown in the following formula. WORDS = ((BitBLTWidth + 1 + SourcePhase) / 2) x BitBLTHeight The BitBLT engine requires this number of WORDS to be sent from the local CPU before it will end the Write BitBLT operation. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 68 Epson Research and Development Vancouver Design Center Note The BitBLT engine counts WORD writes made to the BitBLT register space. This does not imply only 16-bit CPU instructions are acceptable. If a system is able to separate one DWORD write into two WORD writes and the CPU writes the low word before the high word, then 32-bit CPU instructions are acceptable. Otherwise, 16-bit CPU instructions are required. Example 9: Write a 100 x 20 rectangle at the screen coordinates x = 25, y = 38 using a 320x240 display at a color depth of 8 bpp. 1. Calculate the destination address (upper left corner of the screen BitBLT rectangle) using the following formula. DestinationAddress = (y x ScreenStride) + (x x BytesPerPixel) = (38 x 320) + (25 x 1) = 12185 = 2F99h where: BytesPerPixel = 1 for 8 bpp BytesPerPixel = 2 for 16 bpp ScreenStride = DisplayWidthInPixels x BytesPerPixel = 320 for 8 bpp Program the BitBLT Destination Start Address Register. REG[8010h] is set to 2F99h. 2. Program the BitBLT Width Register to 100 - 1. REG[8018h] is set to 63h (99 decimal). 3. Program the BitBLT Height Register to 20 - 1. REG[801Ch] is set to 13h (19 decimal). 4. Program the Source Phase in the BitBLT Source Start Address Register. In this example the data is WORD aligned, so the source phase is 0. REG[800Ch] is set to 00h. 5. Program the BitBLT Operation Register to select the Write BitBLT with ROP. REG[8008h] bits 3-0 are set to 0h. 6. Program the BitBLT ROP Code Register to select Destination = Source. REG[8008h] bits 19-16 are set to 0Ch. 7. Program the BitBLT Color Format Select bit for 8 bpp operations. REG[8000h] bit 18 is set to 0. 8. Program the BitBLT Memory Offset Register to the ScreenStride in WORDS: BLTMemoryOffset = DisplayWidthInPixels / BytesPerPixel = 320 / 2 = A0h REG[8014h] is set to A0h. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 69 9. Calculate the number of WORDS the BitBLT engine expects to receive. WORDS = ((BLTWidth + 1 + SourcePhase) / 2) x BLTHeight = (100 + 1) / 2 x 20 = 1000 = 3E8h 10. Program the BitBLT Destination/Source Linear Select bits for a rectangular BitBLT (BitBLT Destination Linear Select = 0, BitBLT Source Linear Select = 0). Start the BitBLT operation and wait for the BitBLT engine to start. REG[8000h] bit 0 is set to 1, then wait until REG[8004h] bit 0 returns a 1. 11. Prior to writing any data to the BitBLT FIFO, confirm the BitBLT FIFO is not full (REG[8004h] bit 4 returns a 0). If the BitBLT FIFO Not Empty Status (REG[8004h] bit 6) returns a 0, the FIFO is empty. Write up to 16 WORDS to the BitBLT data register area. If the BitBLT FIFO Not Empty Status (REG[8004h] bit 6) returns a 1 and the BitBLT FIFO Half Full Status (REG[8004h] bit 5) returns a 0 then you can write up to 8 WORDS. If the BitBLT FIFO Full Status returns a 1, do not write to the BitBLT FIFO until it returns a 0. The following table summarizes how many words can be written to the BitBLT FIFO. Table 9-5: Possible BitBLT FIFO Writes BitBLT Status Register (REG[8004h]) FIFO Not Empty Status FIFO Half Full Status FIFO Full Status 0 0 0 1 0 0 1 1 0 1 1 1 Word Writes Available 16 8 up to 8 0 (do not write) Note The sequence of register initialization is irrelevant as long as all required registers are programmed before the BitBLT is started. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 70 Epson Research and Development Vancouver Design Center 9.2.2 Color Expansion BitBLT Similar to the Write BitBLT, the Color Expansion BitBLT requires the CPU to feed data to the BitBLT data register It differs in that bits set to one in the source data becomes a complete pixel of foreground color. Source bits set to zero are converted to a pixel of background color. The intended use of this BitBLT operation is to increase the speed of writing text to display memory. As with the Write BitBLT, all data sent to the BitBLT engine must be WORD (16-bit) writes. The BitBLT engine expands first the low byte, then the high byte starting at bit 7 of each byte. The start byte of the first WORD to be expanded and the start bit position within this byte must be specified. The start byte position is selected by setting source address bit 0 to 0 to start expanding the low byte or 1 to start expanding the high byte. Partially "masked" color expansion BitBLTs can be used when drawing a portion of a pattern (i.e. a portion of a character) on the screen. The following examples illustrate how one WORD is expanded using the Color Expansion BitBLT. 1. To expand bits 0-1 of the word: Source Address = 0 Start Bit Position = 1 BitBLT Width = 2 The following bits are expanded. Word Sent To BitBLT Engine 87 15 0 7 High Byte 0 7 Low Byte 0 2. To expand bits 0-15 of the word (entire word) Source Address = 0 Start Bit Position = 7 (bit seven of the low byte) BitBLT Width = 16 The following bits are expanded. Word Sent To BitBLT Engine 87 15 0 7 High Byte 0 7 Low Byte 0 S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 71 3. To expand bits 8-9 of the word Source Address = 1 Start Bit Position = 1 BitBLT Width = 2 The following bits are expanded. Word Sent To BitBLT Engine 87 15 0 7 High Byte 0 7 Low Byte 0 4. To expand bits 0,15-14 of the word Source Address = 0 Start Bit Position = 0 BitBLT Width = 3 The following bits are expanded. Word Sent To BitBLT Engine 87 15 0 7 High Byte 0 7 Low Byte 0 All subsequent WORDS in one BitBLT line are then serially expanded starting at bit 7 of the low byte until the end of the BitBLT line. All unused bits in the last WORD are discarded. It is extremely important that the exact number of WORDS is provided to the BitBLT engine. The number of WORDS is calculated from the following formula. This formula is valid for all color depths (8/16 bpp). WORDS = ((Sx MOD 16 + BitBLTWidth + 15) / 16) x BitBLTHeight where: Sx is the X coordinate of the starting pixel in a word aligned monochrome bitmap. Monochrome Bitmap Byte 1 Byte 2 Sx = 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 72 Epson Research and Development Vancouver Design Center Example 10: Color expand a rectangle of 12 x 18 starting at the coordinates Sx = 125, Sy = 17 using a 320x240 display at a color depth of 8 bpp. This example assumes a monochrome, WORD aligned bitmap of dimensions 300 x 600 with the origin at an address A. The color expanded rectangle will be displayed at the screen coordinates X = 20, Y = 30. The foreground color corresponds to the LUT entry at index 134, the background color to index 124. 1. First we need to calculate the address of the WORD within the monochrome bitmap containing the pixel x = 125,y = 17. SourceAddress = BitmapOrigin + (y x SourceStride) + (x / 8) = A + (Sy x SourceStride) + (Sx / 8) = A + (17 x 38) + (125 / 8) = A + 646 + 15 = A + 661 = (BitmapWidth + 15) / 16 = (300 + 15) / 16 = 19 WORDS per line = 38 BYTES per line where: SourceStride 2. Calculate the destination address (upper left corner of the screen BitBLT rectangle) using the following formula. DestinationAddress = (Y x ScreenStride) + (X x BytesPerPixel) = (30 x 320) + (20 x 1) = 9620 = 2594h where: BytesPerPixel = 1 for 8 bpp BytesPerPixel = 2 for 16 bpp ScreenStride = DisplayWidthInPixels x BytesPerPixel = 320 for 8 bpp Program the BitBLT Destination Start Address Register. REG[8010h] is set to 2594h. 3. Program the BitBLT Width Register to 12 - 1. REG[8018h] is set to 0Bh (11 decimal). 4. Program the BitBLT Height Register to 18 - 1. REG[801Ch] is set to 11h (17 decimal). 5. Program the Source Phase in the BitBLT Source Start Address Register. In this example the source address equals A + 661 (odd), so REG[800Ch] is set to 1. Since only bit 0 flags the source phase, more efficient code would simply write the low byte of the SourceAddress into REG[800Ch] directly -- not needing to test for an odd/even address. Note that in 16 bpp color depths the Source address is guaranteed to be even. 6. Program the BitBLT Operation Register to select the Color Expand BitBLT. REG[8008h] bits 3-0 are set to 8h. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 73 7. Program the Color Expansion Register. The formula for this example is as follows. Color Expansion = 7 - (Sx MOD 8) = 7 - (125 MOD 8) =7-5 =2 REG[8008h] is set to 2h. 8. Program the Background Color Register to the background color. REG[8020h] is set to 7Ch (124 decimal). 9. Program the Foreground Color Register to the foreground color. REG[8024h] is set to 86h (134 decimal). 10. Program the BitBLT Color Format Register for 8 bpp operation. REG[8000h] bit 18 is set to 0. 11. Program the BitBLT Memory Offset Register to the ScreenStride in WORDS. BltMemoryOffset = ScreenStride / 2 = 320 / 2 = A0h REG[8014h] is set to A0h. 12. Calculate the number of WORDS the BitBLT engine expects to receive. First, the number of WORDS in one BitBLT line must be calculated as follows. WordsOneLine = ((125 MOD 16) + 12 + 15) / 16 = (13 + 12 + 15) / 16 = 40 / 16 =2 Therefore, the total WORDS the BitBLT engine expects to receive is calculated as follows. WORDS = WordsOneLine x 18 = 2 x 18 = 36 13. Program the BitBLT Destination/Source Linear Select bits for a rectangular BitBLT (BitBLT Destination Linear Select = 0, BitBLT Source Linear Select = 0). Start the BitBLT operation and wait for the BitBLT Engine to start. REG[8000h] bit 0 is set to 1, then wait until REG[8004h] bit 0 returns a 1. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 74 Epson Research and Development Vancouver Design Center 14. Prior to writing all WORDS to the BitBLT FIFO, confirm the BitBLT FIFO is not full (REG[8004h] bit 4 returns a 0). One WORD expands into 16 pixels which fills all 16 FIFO words in 16 bpp or 8 FIFO words in 8 bpp. The following table summarizes how many words can be written to the BitBLT FIFO. Table 9-6: Possible BitBLT FIFO Writes BitBLT Status Register (REG[8004h]) FIFO Not Empty Status FIFO Half Full Status FIFO Full Status 0 0 0 1 0 0 1 1 0 1 1 1 8 bpp Word Writes Available 2 1 0 (do not write) 16 bpp Word Writes Available 1 0 (do not write) Note The sequence of register setup is irrelevant as long as all required registers are programmed before the BitBLT is started. 9.2.3 Color Expansion BitBLT With Transparency This BitBLT operation is virtually identical to the Color Expand BitBLT, the difference is in how background bits are handled. Bits in the source bitmap which are set to zero result in the destination pixel being left untouched. Bits set to one are expanded to the foreground color. Use this BitBLT operation to overlay text onto any background while leaving the background intact. Refer to the Color Expansion BitBLT for sample calculations and keep the following points in mind: * Program the BitBLT operation bits, REG[8008h] bits 3-0, to 09h instead of 08h. * Setting a background color, REG[8020h], is not required. 9.2.4 Solid Fill BitBLT The Solid Fill BitBLT fills a rectangular area of the display buffer with a solid color. This operation is used to paint large screen areas or to set areas of the display buffer to a given value. This BitBLT operation is self completing. After setting the width, height, destination start position and (foreground) color the BitBLT engine is started. When the region of display memory is filled with the given color the BitBLT engine will automatically stop. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 75 Example 11: Fill a red 9 x 301 rectangle at the screen coordinates x = 100, y = 10 using a 320x240 display at a color depth of 16 bpp. 1. Calculate the destination address (upper left corner of the destination rectangle) using the following formula. DestinationAddress = (y x ScreenStride) + (x x BytesPerPixel) = (10 x (320 x 2)) + (100 x 2) = 6600 = 19C8h where: BytesPerPixel = 1 for 8 bpp BytesPerPixel = 2 for 16 bpp ScreenStride = DisplayWidthInPixels x BytesPerPixel = 640 for 16 bpp. Program the BitBLT Destination Start Address Register. REG[8010h] is set to 19C8h. 2. Program the BitBLT Width Register to 9 - 1. REG[8018h] is set to 08h. 3. Program the BitBLT Height Register to 301 - 1. REG[801Ch] is set to 12Ch (300 decimal). 4. Program the BitBLT Foreground Color Register. REG[8024h] is set to F800h (Full intensity red in 16 bpp is F800h). 5. Program the BitBLT Operation Register to select Solid Fill. REG[8008h] bits 3-0 are set to 0Ch. 6. Program the BitBLT Color Format Register for 16 bpp operations. REG[8000h] bit 18 is set to 1. 7. Program the BitBLT Memory Offset Register to the ScreenStride in WORDS. BltMemoryOffset = ScreenStride / 2 = 320 = 140h REG[8014h] is set to 0140h. 8. Program the BitBLT Destination/Source Linear Select bits for a rectangular BitBLT (BitBLT Destination Linear Select = 0, BitBLT Source Linear Select = 0). Start the BitBLT operation. REG[8000h] bit 0 is set to 1. Note The sequence of register setup is irrelevant as long as all required registers are programmed before the BitBLT is started. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 76 Epson Research and Development Vancouver Design Center 9.2.5 Move BitBLT in a Positive Direction with ROP The Move BitBLT is used to copy one area of display memory to another area in display memory. The source and the destination areas of the BitBLT may be either rectangular or linear. Performing a rectangular to rectangular Move BitBLT creates an exact copy of one portion of video memory at the second location. Selecting a rectangular source to linear destination would be used to compactly store an area of displayed video memory into non-displayed video memory. Later, the area could be restored by performing a linear source to rectangular destination Move BitBLT. The Move BitBLT in a Positive Direction with ROP is a self completing operation. Once the width, height and the source and destination start addresses are setup and the BitBLT is started the BitBLT engine will complete the operation automatically. Should the source and destination areas overlap a decision has to be made as to whether to use a Positive or Negative direction so that source data is not overwritten by the move before it is used. Refer to Figure 9-1: to see when to make the decision to switch to the Move BitBLT in a Negative direction. When the destination area overlaps the original source area and the destination address is greater then the source address, use the Move BitBLT in Negative Direction with ROP. D S S D Destination Address less than Source Address Use Move BitBLT in Positive Direction Destination Address greater than Source Address Use Move BitBLT in Negative Direction Figure 9-1: Move BitBLT Usage S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 77 Example 12: Copy a 9 x 101 rectangle at the screen coordinates x = 100, y = 10 to screen coordinates x = 200, y = 20 using a 320x240 display at a color depth of 16 bpp. 1. Calculate the source and destination addresses (upper left corners of the source and destination rectangles), using the following formula. SourceAddress = (y x ScreenStride) + (x x BytesPerPixel) = (10 x (320 x 2)) + (100 x 2) = 6600 = 19C8h DestinationAddress = (y x ScreenStride) + (x x BytesPerPixel) = (20 x (320 x 2)) + (200 x 2) = 13200 = 3390h where: BytesPerPixel = 1 for 8 bpp BytesPerPixel = 2 for 16 bpp ScreenStride = DisplayWidthInPixels x BytesPerPixel = 640 for 16 bpp Program the BitBLT Source Start Address Register. REG[800Ch] is set to 19C8h. Program the BitBLT Destination Start Address Register. REG[8010h] is set to 3390h. 2. Program the BitBLT Width Register to 9 - 1. REG[8018h] is set to 08h. 3. Program the BitBLT Height Register to 101 - 1. REG[801Ch] is set to 64h (100 decimal). 4. Program the BitBLT Operation Register to select the Move BitBLT in Positive Direction with ROP. REG[8008h] bits 3-0 are set to 2h. 5. Program the BitBLT ROP Code Register to select Destination = Source. REG[8008h] bits 19-16 are set to 0Ch. 6. Program the BitBLT Color Format Select bit for 16 bpp operations. REG[8000h] bit 18 is set to 1. 7. Program the BitBLT Memory Offset Register to the ScreenStride in WORDS. BltMemoryOffset = ScreenStride / 2 = 320 = 140h REG[8014h] is set to 0140h. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 78 Epson Research and Development Vancouver Design Center 8. Program the BitBLT Destination/Source Linear Select bits for a rectangular BitBLT (BitBLT Destination Linear Select = 0, BitBLT Source Linear Select = 0). Start the BitBLT operation. REG[8000h] bit 0 is set to 1. Note The sequence of register setup is irrelevant as long as all required registers are programmed before the BitBLT is started. 9.2.6 Move BitBLT in Negative Direction with ROP The Move BitBLT in Negative Direction with ROP is similar to the Move BitBLT in Positive direction. Use this BitBLT operation when the source and destination BitBLT areas overlap and the destination address is greater then the source address. Refer to Figure 9-1: on page 76 to see when to make the decision to switch to the Move BitBLT in a Positive direction. When using the Move BitBLT in Negative Direction it is necessary to calculate the addresses of the last pixels as opposed to the first pixels. This means calculating the addresses of the lower right corners as opposed to the upper left corners. Example 13: Copy a 9 x 101 rectangle at the screen coordinates x = 100, y = 10 to screen coordinates X = 105, Y = 20 using a 320x240 display at a color depth of 16 bpp. In the following example, the coordinates of the source and destination rectangles intentionally overlap. 1. Calculate the source and destination addresses (lower right corners of the source and destination rectangles) using the following formula. SourceAddress = ((y + Height - 1) x ScreenStride) + ((x + Width - 1) x BytesPerPixel) = ((10 + 101 - 1) x (320 x 2)) + ((100 + 9 - 1) x 2) = 70616 = 113D8h DestinationAddress = ((Y + Height - 1) x ScreenStride) + ((X + Width - 1) x BytesPerPixel) = ((20 + 101 - 1) x (320 x 2)) + ((105 + 9 - 1) x 2) = 77026 = 12CE2h where: BytesPerPixel = 1 for 8 bpp BytesPerPixel = 2 for 16 bpp ScreenStride = DisplayWidthInPixels x BytesPerPixel = 640 for 16 bpp Program the BitBLT Source Start Address Register. REG[800Ch] is set to 113D8h. Program the BitBLT Destination Start Address Register. REG[8010h] is set to 12CE2h. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 79 2. Program the BitBLT Width Register to 9 - 1. REG[8018h] is set to 08h. 3. Program the BitBLT Height Register to 101 - 1. REG[801Ch] is set to 64h (100 decimal). 4. Program the BitBLT Operation Register to select the Move BitBLT in Negative Direction with ROP. REG[8008] bits 3-0 are set to 3h. 5. Program the BitBLT ROP Code Register to select Destination = Source. REG[8008h] bits 19-16 are set to 0Ch. 6. Program the BitBLT Color Format Select bit for 16 bpp operations. REG[8000h] bit 18 is set to 1. 7. Program the BitBLT Memory Offset Register to the ScreenStride in WORDS. BltMemoryOffset = ScreenStride / 2 = 320 = 140h REG[8014h] is set to 0140h. 8. Program the BitBLT Destination/Source Linear Select bits for a rectangular BitBLT (BitBLT Destination Linear Select = 0, BitBLT Source Linear Select = 0). Start the BitBLT operation. REG[8000h] bit 0 is set to 1. Note The sequence of register setup is irrelevant as long as all required registers are programmed before the BitBLT is started. 9.2.7 Transparent Write BitBLT Transparent Write BitBLTs are similar to the Write BitBLT with ROP with two differences; first, a specified color in the source data leaves the destination pixel untouched and second ROPs are not supported. This operation is used to copy a bitmap image from system memory to the display buffer with one color marked as transparent. Pixels of the transparent color are not transferred. This allows fast display of non-rectangular or masked images. For example, consider a source bitmap having a red circle on a blue background. By selecting the blue as the transparent color and using the Transparent Write BitBLT on the whole rectangle, the effect is a BitBLT of the red circle only. During a Transparent Write BitBLT operation the BitBLT engine expects to receive a particular number of WORDs and it is the responsibility of the CPU to provide the required amount of data. When performing BitBLTs at 16 bpp color depth the number of WORDS to be sent is the same as the number of pixels as each pixel is one WORD wide. The number of WORD writes the BitBLT engine expects is calculated using the following formula. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 80 Epson Research and Development Vancouver Design Center WORDS = Pixels = BitBLTWidth x BitBLTHeight When the color depth is 8 bpp the formula must take into consideration that the BitBLT engine accepts only WORD accesses and each pixel is one BYTE. This may lead to a different number of WORD transfers than there are pixels to transfer. The number of WORD accesses is dependant on the position of the first pixel within the first WORD of each row. Is the pixel stored in the low byte or the high byte of the WORD? This aspect of the BitBLT is called phase and is determined as follows: Source phase is 0 when the first pixel is in the low byte and the second pixel is in the high byte of the WORD. When the source phase is 0, bit 0 of the Source Start Address Register is 0. The Source Phase is 1 if the first pixel of each row is contained in the high byte of the WORD, the contents of the low byte are ignored. When the source phase is 1, bit 0 of the Source Start Address Register is set. Depending on the Source Phase and the BitBLT Width, the last WORD may contain only one pixel. In this case it is always in the low byte. The number of WORD writes the BitBLT engine expects for 8 bpp color depths is shown in the following formula. WORDS = ((BitBLTWidth + 1 + SourcePhase) / 2) x BitBLTHeight Once the Transparent Write BitBLT begins, the BitBLT engine remains active until all pixels have been written. The BitBLT engine requires this number of WORDS to be sent from the local CPU before it ends the Transparent Write BitBLT operation. Note The BitBLT engine counts WORD writes made to the BitBLT register. This does not imply only 16-bit CPU instructions are acceptable. If a system is able to separate one DWORD write into two WORD writes and the CPU writes the low word before the high word, then 32-bit CPU instructions are acceptable. Otherwise, 16-bit CPU instructions are required. Example 14: Write 100 x 20 pixels at the screen coordinates x = 25, y = 38 using a 320x240 display at a color depth of 8 bpp. Transparent color is high intensity blue (assume LUT Index 124). 1. Calculate the destination address (upper left corner of the screen BitBLT rectangle), using the formula: DestinationAddress = (y x ScreenStride) + (x x BytesPerPixel) = (38 x 320) + (25 x 1) = 12185 = 2F99h where: BytesPerPixel = 1 for 8 bpp BytesPerPixel = 2 for 16 bpp ScreenStride = DisplayWidthInPixels x BytesPerPixel = 320 for 8 bpp Program the BitBLT Destination Start Address Register. REG[8010h] is set to 2F99h. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 81 2. Program the BitBLT Width Register to 100 - 1. REG[8018h] is set to 63h (99 decimal). 3. Program the BitBLT Height Register to 20 - 1. REG[801Ch] is set to 13h (19 decimal). 4. Program the Source Phase in the BitBLT Source Start Address Register. In this example, the data is WORD aligned, so the source phase is 0. REG[800Ch] is set to 00h. 5. Program the BitBLT Operation Register to select Transparent Write BitBLT. REG[8008h] bits 3-0 are set to 4h. 6. Program the BitBLT Background Color Register to select transparent color. REG[8020h] is set to 7Ch (124 decimal). 7. Program the BitBLT Color Format Select bit for 8 bpp operations. REG[8000h] bit 18 is set to 0. 8. Program the BitBLT Memory Offset Register to the ScreenStride in WORDS. BltMemoryOffset = ScreenStride / 2 = 320 / 2 = 160 = A0h REG[8014h] is set to 0A0h. 9. Calculate the number of WORDS the BitBLT engine expects to receive. WORDS = ((BLTWidth + 1 + SourcePhase) / 2) x BLTHeight = (100 + 1 + 0) / 2 x 20 = 1000 = 3E8h 10. Program the BitBLT Destination/Source Linear Select bits for a rectangular BitBLT (BitBLT Destination Linear Select = 0, BitBLT Source Linear Select = 0). Start the BitBLT operation and wait for the BitBLT engine to start. REG[8000h] bit 0 is set to 1, then wait until REG[8004h] bit 0 returns a 1. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 82 Epson Research and Development Vancouver Design Center 11. Prior to writing any data to the BitBLT FIFO, confirm the BitBLT FIFO is not full (REG[8004h] bit 4 returns a 0). If the BitBLT FIFO Not Empty Status (REG[8004h] bit 6) returns a 0, the FIFO is empty. Write up to 16 WORDS to the BitBLT data register area. If the BitBLT FIFO Not Empty Status (REG[8004h] bit 6) returns a 1 and the BitBLT FIFO Half Full Status (REG[8004h] bit 5) returns a 0 then you can write up to 8 WORDS. If the BitBLT FIFO Full Status returns a 1, do not write to the BitBLT FIFO until it returns a 0. The following table summarizes how many words can be written to the BitBLT FIFO. Table 9-7: Possible BitBLT FIFO Writes BitBLT Status Register (REG[8004h]) FIFO Not Empty Status FIFO Half Full Status FIFO Full Status 0 0 0 1 0 0 1 1 0 1 1 1 Word Writes Available 16 8 less than 8 0 (do not write) Note The sequence of register setup is irrelevant as long as all required registers are programmed before the BitBLT is started. 9.2.8 Transparent Move BitBLT in Positive Direction The Transparent Move BitBLT in Positive Direction combines the capabilities of the Move BitBLT with the ability to define a transparent color. Use this operation to copy a masked area of display memory to another area in display memory. The source and the destination areas of the BitBLT may be either rectangular or linear. Performing a rectangular to rectangular Move BitBLT creates an exact copy of one portion of video memory at the second location. Selecting a rectangular source to linear destination would be used to compactly store an area of displayed video memory into non-displayed video memory. Later, the area could be restored by performing a linear source to rectangular destination Move BitBLT. The transparent color is not copied during this operation, whatever pixel color existed in the destination will be there when the BitBLT completes. This allows fast display of nonrectangular images. For example, consider a source bitmap having a red circle on a blue background. By selecting the blue color as the transparent color and using the Transparent Move BitBLT on the whole rectangle, the effect is a BitBLT of the red circle only. Note The Transparent Move BitBLT is supported only in a positive direction. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 83 Example 15: Copy a 9 x 101 rectangle at the screen coordinates x = 100, y = 10 to screen coordinates X = 200, Y = 20 using a 320x240 display at a color depth of 16 bpp. Transparent color is blue. 1. Calculate the source and destination addresses (upper left corners of the source and destination rectangles), using the formula: SourceAddress = (y x ScreenStride) + (x x BytesPerPixel) = (10 x (320 x 2)) + (100 x 2) = 6600 = 19C8h DestinationAddress = (Y x ScreenStride) + (X x BytesPerPixel) = (20 x (320 x 2)) + (200 x 2) = 13200 = 3390h where: BytesPerPixel = 1 for 8 bpp BytesPerPixel = 2 for 16 bpp ScreenStride = DisplayWidthInPixels x BytesPerPixel = 640 for 16 bpp Program the BitBLT Source Start Address Register. REG[800Ch] is set to 19C8h. Program the BitBLT Destination Start Address Register. REG[8010h] is set to 3390h. 2. Program the BitBLT Width Register to 9 - 1. REG[8018h] is set to 08h. 3. Program the BitBLT Height Register to 101 - 1. REG[801Ch] is set to 64h (100 decimal). 4. Program the BitBLT Operation Register to select the Transparent Move BitBLT in Positive Direction. REG[8008h] bits 3-0 are set to 05h. 5. Program the BitBLT Background Color Register to select blue as the transparent color. REG[8020h] is set to 001Fh (Full intensity blue in 16 bpp is 001Fh). 6. Program the BitBLT Color Format Register to select 16 bpp operations. REG[8000h] bit 18 is set to 1. 7. Program the BitBLT Memory Offset Register to the ScreenStride in WORDS. BltMemoryOffset = ScreenStride / 2 = 320 = 140h REG[8014h] is set to 0140h. 8. Program the BitBLT Destination/Source Linear Select bits for a rectangular BitBLT (BitBLT Destination Linear Select = 0, BitBLT Source Linear Select = 0). Start the BitBLT operation. REG[8000h] bit 0 is set to 1. Note The order of register setup is irrelevant as long as all relevant registers are programmed before the BitBLT is initiated. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 84 Epson Research and Development Vancouver Design Center 9.2.9 Pattern Fill BitBLT with ROP The Pattern Fill BitBLT with ROP fills a specified area of display memory with a pattern. The pattern is repeated until the fill area is completely filled. The fill pattern is limited to an eight by eight pixel array and must be loaded to off-screen video memory before starting the BitBLT. The pattern can be logically combined with the destination using any of the 16 ROP codes, but typically the copy pattern ROP is used (ROP code 0Ch). A pattern is defined to be an array of 8x8 pixels and the pattern data must be stored in consecutive bytes of display memory (64 consecutive bytes for 8 bpp color depths and 128 bytes for 16 bpp color depths). For 8 bpp color depths the pattern must begin on a 64 byte boundary, for 16 bpp color depths the pattern must begin on a 128 byte boundary. This operation is self completing. Once the parameters have been entered and the BitBLT started the BitBLT engine will fill all of the specified memory with the pattern. To fill an area using the pattern BitBLT, the BitBLT engine requires the location of the pattern, the destination rectangle position and size, and the ROP code. The BitBLT engine also needs to know which pixel from the pattern is the first pixel in the destination rectangle (the pattern start phase). This allows seamless redrawing of any part of the screen using the pattern fill. Example 16: Fill a 100 x 150 rectangle at the screen coordinates x = 10, y = 20 with the pattern in off-screen memory at offset 27000h using a 320x240 display at a color depth of 8 bpp. The first pixel (upper left corner) of the rectangle is the pattern pixel at x = 3, y = 4. 1. Calculate the destination address (upper left corner of the destination rectangle), using the formula: DestinationAddress = (y x ScreenStride) + (x x BytesPerPixel) = (20 x 320) + (10 x 1) = 6410 = 190Ah where: BytesPerPixel = 1 for 8 bpp BytesPerPixel = 2 for 16 bpp ScreenStride = DisplayWidthInPixels x BytesPerPixels = 320 for 8 bpp Program the BitBLT Destination Start Address Register. REG[8010h] is set to 190Ah. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 85 2. Calculate the source address. This is the address of the pixel in the pattern that is the origin of the destination fill area. The pattern begins at offset 156K but the first pattern pixel is at x = 3, y = 4. Therefore, an offset within the pattern itself must be calculated. SourceAddress = PatternOffset + StartPatternY x 8 x BytesPerPixel + StartPatternX x BytesPerPixel = 156K + (4 x 8 x 1) + (3 x 1) = 156K + 35 = 159779 = 27023h where: BytesPerPixel = 1 for 8 bpp BytesPerPixel = 2 for 16 bpp Program the BitBLT Source Start Address Register. REG[800Ch] is set to 27023h. 3. Program the BitBLT Width Register to 100 - 1. REG[8018h] is set to 63h (99 decimal). 4. Program the BitBLT Height Register to 150-1. REG[801Ch] is set to 95h (149 decimal). 5. Program the BitBLT Operation Register to select the Pattern Fill with ROP. REG[8008h] bits 3-0 are set to 6h. 6. Program the BitBLT ROP Code Register to select Destination = Source. REG[8008h] bits 19-16 are set to 0Ch. 7. Program the BitBLT Color Format Select bit for 8 bpp operations. REG[8000h] bit 18 is set to 0. 8. Program the BitBLT Memory Offset Register to the ScreenStride in WORDS. BltMemoryOffset = ScreenStride / 2 = 320 / 2 = 160 = A0h REG[8014h] is set to 00A0h. 9. Program the BitBLT Destination/Source Linear Select bits for a rectangular BitBLT (BitBLT Destination Linear Select = 0, BitBLT Source Linear Select = 0). Start the BitBLT operation. REG[8000h] bit 0 is set to 1. Note The sequence of register setup is irrelevant as long as all required registers are programmed before the BitBLT is started. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 86 Epson Research and Development Vancouver Design Center 9.2.10 Pattern Fill BitBLT with Transparency This operation is very similar to the Pattern Fill BitBLT with the difference being that one color can be specified to be transparent. Whenever the Transparent color is encountered in the pattern data the destination is left as is. This operation is useful to create hatched or striped patterns where the original image shows through the hatching. The requirements for this BitBLT are the same as for the Pattern Fill BitBLT the only change in programming is that the BitBLT Operation field of REG[8008h] must be set to 07h and the BitBLT Background color register, REG[8020h] must be set to the desired color. Example 17: Fill a 100 x 150 rectangle at the screen coordinates x = 10, y = 20 with the pattern in off-screen memory at offset 27000h using a 320x240 display at a color depth of 8 bpp. The first pixel (upper left corner) of the rectangle is the pattern pixel at x = 3, y = 4. Transparent color is blue (assumes LUT index 1). 1. Calculate the destination address (upper left corner of destination rectangle), using the formula: DestinationAddress = (y x ScreenStride) + (x x BytesPerPixel) = (20 x 320) + (10 x 1) = 6410 = 190Ah where: BytesPerPixel = 1 for 8 bpp BytesPerPixel = 2 for 16 bpp ScreenStride = DisplayWidthInPixels x BytesPerPixels = 320 for 8 bpp Program the BitBLT Destination Start Address Register. REG[8010h] is set to 190Ah. 2. Calculate the source address. This is the address of the pixel in the pattern that is the origin of the destination fill area. The pattern begins at offset 1M, but the first pattern pixel is at x = 3, y = 4. Therefore, an offset within the pattern itself must be calculated. SourceAddress = PatternOffset + StartPatternY x 8 x BytesPerPixel + StartPatternX x BytesPerPixel = 156K + (4 x 8 x 1) + (3 x 1) = 156K + 35 = 159779 = 27023h where: BytesPerPixel = 1 for 8 bpp BytesPerPixel = 2 for 16 bpp Program the BitBLT Source Start Address Register. REG[800Ch] is set to 27023h. 3. Program the BitBLT Width Register to 100 - 1. REG[8018h] is set to 63h (99 decimal). S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 87 4. Program the BitBLT Height Register to 150-1. REG[801Ch] is set to 95h (149 decimal). 5. Program the BitBLT Operation Register to select the Pattern Fill BitBLT with Transparency. REG[8008h] bits 3-0 are set to 7h. 6. Program the BitBLT Background Color Register to select transparent color. This example uses blue (LUT index 1) as the transparent color. REG[8020h] is set to 01h. 7. Program the BitBLT Color Format Select bit for 8 bpp operations. REG[8000h] bit 18 is set to 0. 8. Program the BitBLT Memory Offset Register to the ScreenStride in WORDS. BltMemoryOffset = ScreenStride / 2 = 320 / 2 = 160 = A0h REG[8014h] is set to A0h. 9. Program the BitBLT Destination/Source Linear Select bits for a rectangular BitBLT (BitBLT Destination Linear Select = 0, BitBLT Source Linear Select = 0). Start the BitBLT operation. REG[8000h] bit 0 is set to 1. Note The sequence of register setup is irrelevant as long as all required registers are programmed before the BitBLT is started. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 88 Epson Research and Development Vancouver Design Center 9.2.11 Move BitBLT with Color Expansion The Move BitBLT with Color Expansion takes a monochrome bitmap as the source and color expands it into the destination. All bits set to one in the source are expanded to destination pixels of the selected foreground color. All bits set to zero in the source are expanded to pixels of the selected background color. The Move BitBLT with Color Expansion is used to accelerate text drawing. A monochrome bitmap of a font, in off-screen video memory, occupies very little space and takes advantage of the hardware acceleration. Since the foreground and background colors are programmable, text of any color can be created. The Move BitBLT with Color Expansion can move data from one rectangular area to another, or either the source or destination may be specified to be linear. Storing rectangular display data in linear format in off screen memory results in a tremendous space saving. Example 18: Color expand a 9 x 16 rectangle using the pattern in off-screen memory at 27000h and move it to the screen coordinates x = 200, y = 20. Assume a 320x240 display at a color depth of 16 bpp, Foreground color of black, and background color of white. 1. Calculate the destination and source addresses (upper left corner of the destination and source rectangles), using the formula. DestinationAddress = (y x ScreenStride) + (x x BytesPerPixel) = (20 x (320 x 2)) + (200 x 2) = 13200 = 3390h where: BytesPerPixel = 1 for 8 bpp BytesPerPixel = 2 for 16 bpp ScreenStride = DisplayWidthInPixels x BytesPerPixels = 640 for 16 bpp SourceAddress = 156K = 27000h Program the BitBLT Destination Start Address Register. REG[8010h] is set to 3390h. Program the BitBLT Source Start Address Register. REG[800Ch] is set to 27000h. 2. Program the BitBLT Width Register to 9 - 1. REG[8018h] is set to 08h. 3. Program the BitBLT Height Register to 16 - 1. REG[801Ch] is set to 0Fh. 4. Program the BitBLT ROP Code/Color Expansion Register. REG[8008h] bits 19-16 are set to 7h. 5. Program the BitBLT Operation Register to select the Move BitBLT with Color Expansion. REG[8008h] bits 3-0 are set to 0Bh. 6. Program the BitBLT Foreground Color Register to select black (in 16 bpp black = 0000h). REG[8024h] is set to 0000h. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 89 7. Program the BitBLT Background Color Register to select white (in 16 bpp white = FFFFh). REG[8024h] is set to FFFFh. 8. Program the BitBLT Color Format Select bit for 16 bpp operations. REG[8000h] bit 18 is set to 1. 9. Program the BitBLT Memory Offset Register to the ScreenStride in WORDS. BltMemoryOffset = ScreenStride / 2 = 320 = 140h REG[8014h] is set to 0140h. 10. Program the BitBLT Destination/Source Linear Select bits for a rectangular BitBLT (BitBLT Destination Linear Select = 0, BitBLT Source Linear Select = 0). Start the BitBLT operation. REG[8000h] bit 0 is set to 1. Note The sequence of register setup is irrelevant as long as all required registers are programmed before the BitBLT is started. 9.2.12 Transparent Move BitBLT with Color Expansion The Transparent Move BitBLT with Color Expansion is virtually identical to the Move BitBLT with Color Expansion. This operation expands bits set to one in the source bitmap to the foreground color. Bits set to zero in the source bitmap leave the corresponding destination pixel as is. Setup and use this operation is exactly as with the Move BitBLT with Color Expansion. 9.2.13 Read BitBLT This Read BitBLT increases the speed of transferring data from the video memory to system memory. This BitBLT complements the Write BitBLT and is typically used to save a part of the display buffer to the system memory. Once the Read BitBLT begins, the BitBLT engine remains active until all the pixels have been read. During a Read BitBLT operation the BitBLT engine expects to send a particular number of WORDs to the CPU and it is the responsibility of the CPU to read the required amount of data. When performing BitBLT at 16 bpp color depth the number of WORDS to be sent is the same as the number of pixels to be transferred as each pixel is one WORD wide. The number of WORD writes the BitBLT engine expects is calculated using the following formula. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 90 Epson Research and Development Vancouver Design Center WORDS = Pixels = BitBLTWidth x BitBLTHeight When the color depth is 8 bpp the formula must take into consideration that the BitBLT engine accepts only WORD accesses and pixels are only one BYTE. This may lead to a different number of WORD transfers than there are pixels to transfer. The number of WORD accesses is dependant on the position of the first pixel within the first WORD of each destination row. Is the pixel stored in the low byte or the high byte of the WORD? Read BitBLT phase is determined as follows: Destination phase is 0 when the first pixel is in the low byte and the second pixel is in the high byte of the WORD. When the destination phase is 0, bit 0 of the Destination Start Address Register is 0. The destination phase is 1 if the first pixel of each destination row is contained in the high byte of the WORD, the contents of the low byte are ignored. When the destination phase is 1, bit 0 of the Destination Start Address Register is set. Depending on the destination phase and the BitBLT width, the last WORD may contain only one pixel. In this case it is always in the low byte. The number of WORD writes the BitBLT engine expects for 8 bpp color depths is shown in the following formula. WORDS = ((BitBLTWidth + 1 + DestinationPhase) / 2) x BitBLTHeight The BitBLT engine requires this number of WORDS to be sent from the local CPU before it will end the Write BitBLT operation. Example 19: Read 100 x 20 pixels at the screen coordinates x = 25, y = 38 and save to system memory. Assume a display of 320x240 at a color depth of 8 bpp. 1. Calculate the source address (upper left corner of the screen BitBLT rectangle), using the formula. SourceAddress = (y x ScreenStride) + (x x BytesPerPixel) = (38 x 320) + (25 x 1) = 12185 = 2F99h where: BytesPerPixel = 1 for 8 bpp BytesPerPixel = 2 for 16 bpp ScreenStride = DisplayWidthInPixels x BytesPerPixels = 320 for 8 bpp Program the BitBLT Source Start Address Register. REG[800Ch] is set to 2F99h. 2. Program the BitBLT Width Register to 100 - 1. REG[8018h] is set to 63h (99 decimal). 3. Program the BitBLT Height Register to 20 - 1. REG[801Ch] is set to 13h (19 decimal). S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 91 4. Program the Destination Phase in the BitBLT Destination Start Address Register. In this example, the data is WORD aligned, so the destination phase is 0. REG[8010h] is set to 00h. 5. Program the BitBLT Operation to select the Read BitBLT. REG[8008h] bits 3-0 are set to 1h. 6. Program the BitBLT Color Format Select bit for 8 bpp operations. REG[8000h] bit 18 is set to 0. 7. Program the BitBLT Memory Offset Register to the ScreenStride in WORDS. BltMemoryOffset = ScreenStride / 2 = 320 / 2 = 160 = A0h REG[8014h] is set to 0A0h. 8. Calculate the number of WORDS the BitBLT engine expects to receive. WORDS = ((BLTWidth + 1 + DestinationPhase) / 2) xBLTHeight = (100 + 1 + 0) / 2 x 20 = 1000 = 3E8h 9. Program the BitBLT Destination/Source Linear Select bits for a rectangular BitBLT (BitBLT Destination Linear Select = 0, BitBLT Source Linear Select = 0). Start the BitBLT operation and wait for the BitBLT engine to start. REG[8000h] bit 0 is set to 1, then wait until REG[8004h] bit 0 returns a 1. 10. Prior to reading from the BitBLT FIFO, confirm the BitBLT FIFO is not empty (REG[8004h] bit 4 returns a 1). If the BitBLT FIFO Not Empty Status (REG[8004h] bit 6) returns a 1 and the BitBLT FIFO Half Full Status (REG[8004h] bit 5) returns a 0 then you can read up to 8 WORDS. If the BitBLT FIFO Full Status returns a 1, read up to 16 WORDS. If the BitBLT FIFO Not Empty Status returns a 0 (the FIFO is empty), do not read from the BitBLT FIFO until it returns a 1. The following table summarizes how many words can be read from the BitBLT FIFO. Table 9-8: Possible BitBLT FIFO Reads BitBLT Status Register (REG[8004h]) FIFO Not Empty Status FIFO Half Full Status FIFO Full Status 0 0 0 1 0 0 1 1 0 1 1 1 Word Reads Available 0 (do not read) up to 8 8 16 Note The sequence of register initialization is irrelevant as long as all required registers are programmed before the BitBLT is started. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 92 Epson Research and Development Vancouver Design Center 9.3 S1D13A04 BitBLT Synchronization A BitBLT operation can only be started if the BitBLT engine is not busy servicing another BitBLT. Before a new operation is started, software must confirm the BitBLT Busy Status bit (REG[8004h] bit 0) is set to zero. The status of this bit can either be tested after each BitBLT operation, or before each BitBLT operation. Testing the BitBLT Status After Testing the BitBLT Active Status after starting a new BitBLT is simpler and less prone to errors. To test after each BitBLT operation, perform the following. 1. Program and start the BitBLT engine. 2. Wait for the current BitBLT operation to finish -- Poll the BitBLT Busy Status bit (REG[8004h] bit 0) until it returns a 0. 3. Continue with program execution. Testing the BitBLT Status Before Testing the BitBLT Active Status before starting a new BitBLT results in better performance, as both CPU and BitBLT engine can be running at the same time. This is most useful for BitBLTs that are self completing (once started they don't require any CPU assistance). While the BitBLT engine is busy, the CPU can do other tasks. To test before each BitBLT operation, perform the following. 1. Wait for the current BitBLT operation to finish -- Poll the BitBLT Busy Status bit (REG[8004h] bit 0) until it returns a 0. 2. Program and start the new BitBLT operation. 3. Continue with program execution (CPU and BitBLT engine work independently). This approach can pose problems when mixing CPU and BitBLT access to the display buffer. For example, if the CPU writes a pixel while the BitBLT engine is running and the CPU writes a pixel before the BitBLT finishes, the pixel may be overwritten by the BitBLT. To avoid this scenario, always assure no BitBLT is in progress before accessing the display buffer with the CPU, or don't use the CPU to access the display buffer at all. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 93 9.4 S1D13A04 BitBLT Known Limitations The S1D13A04 BitBLT engine has the following limitations. * The 2D Accelerator Data Memory Mapped register must not be accessed except during BitBLT operations. Read from the register only during Read BitBLT operations and write to the register only during Write and Color Expand BitBLTs. Accessing the register at any other time may result in S1D13A04 stopping to respond and the system to freeze. * The Read and Write BitBLT operations are not available when the S1D13A04 is configured for the Redcap or Dragonball without DTACK host bus interfaces. * A BitBLT operation cannot be terminated once it has been started. 9.5 Sample Code Sample code demonstrating how to program the S1D13A04 BitBLT engine is provided in the file A04sample.zip. This file is available on the internet at www.erd.epson.com. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 94 Epson Research and Development Vancouver Design Center 10 Programming the USB Controller USB (Universal Serial Bus) is an external bus designed to ease the connection and use of peripheral devices. USB incorporates a host/client architecture in which the host initiates all data transactions and the client either receives or supplies data to the host. USB offers the following features to the end user: * Single plug type for all peripheral devices. * Support for up to 127 simultaneous devices. * Speeds up to 12 Megabits per second. * "hot-plugging" peripherals. The S1D13A04 USB controller supports revision 1.1 of the USB specification. The S1D13A04 USB controller handles many common USB tasks without requiring local processor intervention. For example, setup and data transfers are handled automatically by the S1D13A04 controller. The controller notifies the local CPU, through an interrupt, when data is ready to be read from the FIFO or when data has been transmitted to the host. This section demonstrates how to program and use the S1D13A04 USB controller. Topics covered include: * Basic concepts such as registers and interrupts * Initialization and data transfers * S1D13A04 USB known issues. 10.1 Registers and Interrupts 10.1.1 Registers Configuration, interrupt notification, and data transfers are all done using the S1D13A04 USB registers. The USB registers are located 4000h bytes past the beginning of S1D13A04 address space and should be written/read using 16 bit accesses. On most systems the start of S1D13A04 address space, is fixed by the system design. The S1D13A04 evaluation board uses a PCI interface, thus the start of S1D13A04 address space may vary from one session to the next. Example code is written using a pointer to the USB registers (pUSB). The USB examples do not show how to obtain the register address. For a description of how to get the register address when using the S5U13A04B00C evaluation board, refer to the function halAcquireController() in Section 11, "Hardware Abstraction Layer" on page 112. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 95 10.1.2 Interrupts The S1D13A04 uses an interrupt to notify the local CPU when a USB event, which requires servicing, occurs. Events, such as USB reset and data transfer notifications generate interrupts. It is beyond the scope of this document to explain how to setup and configure the interrupt system for the variety of platforms the S1D13A04 supports. The examples and flowcharts assume there is one interrupt handling routine which will determine the cause of the interrupt and call the appropriate handler function. It is assumed the user understands the mechanics and architecture of their system well enough setup a routine which will receive an interrupt notification and determine the cause of the interrupt. 10.2 Initialization Initialization describes the process of setting the registers state to enable the USB controller for use. There are two cases where the USB registers need to be initialized. When the system is powered up and the registers need to be prepared for first use. The second time the registers need to be initialized is after receiving a RESET request from the host controller. Refer to Section 10.2.2, "USB Registers" on page 96 for an example of the register initialization sequence. 10.2.1 GPIO Setup The S1D13A04 shares four lines between GPIO and USB use. Before any accesses are made to the USB section the GPIO lines must be configured. To set the GPIO lines write the binary value 0010xxxx-1101xxxx-00000000-xxxxxxxx (2xDx00xxh) to REG[64h], the GPIO Status and Control register. Note X's represent a don't care state. Depending on other system configuration (i.e. panel technology) certain don't care bits may have to be set also. See the S1D13A04 Hardware Functional Specification, document number X37A-A-001, for more information regarding the bits in the GPIO Status and Control register. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 96 Epson Research and Development Vancouver Design Center 10.2.2 USB Registers The steps described below are typical of the startup of the S1D13A04 USB controller. * registers are set to an initial value * the S1D13A04 is connected to a USB host controller * the host controller issues a RESET command * the USB registers are re-initialized As initialization for both steps are similar it is recommended that one routine perform the sequence. The following table depicts a typical register initialization sequence. Table 10-1: USB Controller Initialization Sequence Register REG[4040h] REG[4044] REG[4000] REG[4024] REG[402C] REG[4032] REG[4004] REG[4010] REG[4018] ext REG[00] ext REG[01] ext REG[02] ext Reg[03] ext REG[0C] REG[4002] REG[4004] REG[4046 REG[4048] REG[404A] REG[404C] REG[4000] USBFC INPUT CONTROL PIN IO STATUS DATA CONTROL EP3 RECEIVE FIFO STATUS USB EP4 TX FIFO STATUS USB STATUS INTERRUPT STATUS 0 EP1 INDEX EP2 INDEX VENDOR ID MSB VENDOR ID LSB PRODUCT ID MSB PRODUCT ID LSB FIFO CONTROL INT ENABLE 0 INT STATUS 0 INTERRUPT CONTROL ENABLE 0 INTERRUPT CONTROL ENABLE 1 INTERRUPT CONTROL STATUS/CLEAR 0 INTERRUPT CONTROL STATUS/CLEAR 1 CONTROL Value (hex) 40 01 84 1C 1C 7E FF 00 00 ?? ?? ?? ?? 01 0A 0A 02 Enable RESET and endpoints notifications 01 7F Clear ALL interrupt status... 7F A4 Enable the USB port for use Notes Enable the USB differential input receiver and indicate we are a bulk transfer self powered device. (for ISOchronous mode, use 43h) USBPUP must be set to enable the USB interface and registers. REG[4000h] to REG[403Ah] cannot be written until this bit is set. Enable the clocks and USB GPIO pins. Clear EP3 status. Clear EP4 status Clear EP2 valid bit Clear any pending USB interrupts Set EP1 index to zero Set EP2 index to zero Provide appropriate vendor ID Provide appropriate product ID Enable EP4 (FIFO) valid transfer mode. Enable interrupts for EP1 and EP3 Make sure any pending interrupts are cleared. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 97 The USB controller is ready for operation with the following configuration: * Endpoint 1 (mailbox receive) is configured for bulk OUT and Endpoint 2 (mailbox transmit) is configured for interrupt IN. The functionality of these endpoints cannot be altered. * Endpoint 3 (FIFO receive) is configured for bulk in and Endpoint 4 (FIFO transmit) is configured for bulk out. Endpoints 3 and 4 may also be configured for isochronous operation. When the S1D13A04 is connected to a host controller, the host will issue a RESET command to the S1D13A04. In response to the RESET the S1D13A04 clears all USB registers in the range REG[4000h] to REG[403Ah]. The client software must respond to the reset and reprogram the USB registers. A host controller may issue a RESET at any time during operation. After the S1D13A04 receives the RESET and re-initializes the registers, the host controller starts the USB SETUP phase. The SETUP sequence is handled entirely by the S1D13A04 USB controller. After the setup is complete the S1D13A3 is ready to begin transferring data. Note Prior to initializing the registers, host controller accesses are responded to with NAKs. After being configured, host controller accesses will be handled in the normal way. Note A Vendor ID can be obtained through the USB Implementers Forum at http://www.usb.org. 10.3 Data Transfers The S1D13A04 USB requires very little local CPU assistance during data transfers. For the most part data transfers from the host involve reading a FIFO data register when notified of that the transfer is complete or writing a FIFO register and setting a 'ready' bit to send data to the host. The following sections expand on the data transfer mechanism. 10.3.1 Receiving Data from the Host - the OUT command Data transferred from the host to the S1D13A04 is directed to either EndPoint 1 (the mailbox) or EndPoint 3 (the FIFO). When the data packet has been successfully received the S1D13A04 generates an interrupt. On receipt of the interrupt the local CPU examines the masked interrupt status registers REG[404Eh] and REG[4050h] to determine the source of the interrupt. If the interrupt came from bit 0 of the Negative Interrupt Masked Status register, REG[4050h], the next step is to examine REG[4004] to determine the exact cause of the interrupt. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 98 Epson Research and Development Vancouver Design Center Endpoint 1 - Mailbox Receive If the cause of the interrupt is determined to be EndPoint 1 (REG[4004h] bit 1 = 1), then the data is read from the EndPoint 1 data register (REG[4012h]). The following figure shows the procedure for the CPU to read the mailbox register. EP1 Receive Clear EP1 Index Register (REG[4010h] == 00h) Initialize local index (Idx = 0) Read byte from EP 1 Read another byte from the mailbox? (Idx < 8)? Yes Receive Mailbox Data (*pBuffer = (REG[4012h]) Increment the local index (Idx++) No Clear EP1 interrupt status (REG[4004h] = 20h) Done Figure 10-1: Endpoint 1 Data Reception Note In this diagram reference is made to two pseudo-variables: Idx is an integer used as a loop counter pBuffer is a pointer to eight bytes of memory to store the EP1 data S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 99 Endpoint 3 - FIFO Receive If the cause of the interrupt is determined to be EndPoint 3, REG[4004h] bit 3 = 1b, then the host controller has sent data to EndPoint 3. Figure 10-2: shows the procedure for reading data from EndPoint 3. An EndPoint 3 interrupt is generated when the number of bytes in the receive FIFO equal the value in the Receive FIFO Almost Full Threshold register (REG[403Ah], Index[06h]). The default value is sixty bytes. On systems where bulk transfers are used, the default value for the receive FIFO threshold should be satisfactory. Systems with slow processors, high interrupt service latency, or configured for isochronous operation may have to decrease this value to allow the CPU time to begin reading data before the data transfer overflows the FIFO. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 100 Epson Research and Development Vancouver Design Center EP3 Receive No Did EP3 ACK? (REG[4032h]b1 ==1)? S1D13A04 successfully received a packet Yes EP3 NAK? Yes (REG[4032h]b2 == 1)? Determine transfer size (Count = min(Remaining, REG[4022h])) Reduce size of remaining transfer (Remaining -= Count) No Flush EP3 FIFO - REG[4024h] = 10h S1D13A04 detected a transaction error and did not respond to the OUT packet No Copy another byte from FIFO? (Cnt > 0)? Yes S1D13A04 responded to the OUT packet with a NAK Transfer Done? (Remaining == 0)? Copy byte from FIFO to local memory (*pLocMem = *REG[4020h)] Point to next local memory - (pLocMem++) Reduce Count - (Count--) Yes Since the transfer is over, there is no need for OUT packets to interrupt the local CPU anymore (this is optional) See 2.5.3 "EP3 Interrupt Status bit set by NAKs" Disable EP3 Interrupt - REG[4002h] &= ~08h Done Figure 10-2: Endpoint 3 Data Reception S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 101 10.3.2 Sending Data to the Host - the IN command Data transfers to the host controller occur when the host issues an IN command. The data comes from EndPoint 2 (the mailbox) or EndPoint 4 (the FIFO). The data transfer is handled automatically by the S1D13A04 and requires no CPU assistance. Data transfers, from the S1D13A04 to the host controller, are performed by writing the data into either EndPoint 2 (mailbox) or EndPoint 4 (FIFO) data registers. After writing the data to the registers a control bit indicating that mailbox or FIFO data is valid is set. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 102 Epson Research and Development Vancouver Design Center Endpoint 2 - Mailbox Transmit Figure 10-3: shows the logical flow for sending data to the host controller using EndPoint 2, the mailbox. EP2 Transmit Clear EP2 valid bit (REG[4032h] = 0) See Section 10.4.4 on page 110 Clear EP2 index register (REG[4018h] = 0) Initialize local count (Idx = 0) Copy another byte? (Idx < 8)? Yes Copy byte to EP2 data (REG[401Ah] = *pBuffer) Increment pointer (pBuffer++) No EP2 will now respond to IN packets with data instead of NAKs Clear EP2 interrupt status (REG[4004h] = 04h) Set EP2 valid (REG[4032h] = 01h) Done Figure 10-3: EndPoint 2 Data Transmission Note In this diagram reference is made to two pseudo-variables: Idx is an integer used as a loop counter pBuffer is a pointer to eight bytes of memory to send to the host Endpoint 4 - Data Transmit Transferring data to the host controller using the FIFO controller has additional overhead as this routine must run tests to ensure error free data transmission. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 103 EP4 Transmit Determine size of packet (PktSize = min(Remain, FIFOSIZE)) Enqueue ZeroLengthPacket (REG[4000h] = 40h) Yes Need to send ZLP? (PktSize == 0)? No Initialize local Count (Count = 0) Copy another byte to FIFO? No (Count < PktSize)? Yes Copy byte to EP4 FIFO (REG[4028h] = *Buffer) Reference next position (pBuffer++) Clear USB EP4 ACK (REG[4032] = 10h) See Section 10.4.1 on page 106, EP4 IRQ status must be cleared within 5 us of EP4 transmit FIFO valid Set EP4 IRQ enable - (REG[4002h] |= 10h) Set Transmit FIFO valid - (REG[402Ch] = 20h) Clear EP4 IRQ Status - (REG[4004h] = 10h) Done Figure 10-4: Endpoint 4 Data Transmission Note In this example there are three variables: PktSize is an integer containing the number of bytes to transfer in this packet Count is an integer used for local loop control pBuffer is a pointer to an array of at least FIFOSIZE bytes. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 104 Epson Research and Development Vancouver Design Center To ensure the host controller receives the packet error free, an interrupt handler for EndPoint 4 must be configured and the flow control as shown in the following diagram must be implemented. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 105 EP4 Int Handler EP4 Int Handler is called after the host controller reads or fails to read a packet. If the host controller successfully read the last packet then the next packet can be loaded into the FIFO. If the host controller failed to read the packet then the last packet must be loaded into the FIFO Packet actually sent? (REG[402Ah] == 0)? No Yes ZLP actually sent? (REG[4000h]b6 == 0)? The last packet was not successfully Yes transmitted No Set Transmit FIFO Valid (REG[402Ch] = 20h) Clear EP4 interrupt status (REG[4004h] = 10h) No EP4 ACK? (REG[4032h]b4 == 1 Done Yes Final packet of transfer was successfully transmitted Last packet short or ZLP? (Remain < FIFOSIZE)? Yes Disable EP4 interrupt (REG[4002h] &= ~10h) Clear EP4 interrupt status (REG[4004h] = 10h) No The last packet was a full packet Advance to end of buffer (pBuffer += Remain) Reduce remaining count to 0 (Remain = 0) Advance pointer to next packet (pBuffer += FIFOSIZE) Reduce remaining transfer size (Remain -= FIFOSIZE) This block is shown as a cleanup step. It is not required. EP4 Data Transmission Done Figure 10-5: Endpoint 4 Interrupt Handling Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 106 Epson Research and Development Vancouver Design Center Note In the diagram the variables: pBuffer is a pointer to the local memory buffer containing the data to be transferred to the host controller Remain is an integer tracking the number of bytes still to be sent. 10.4 Known Issues This section presents known issues with USB transfers when using the S1D13A04 USB controller. 10.4.1 EP4 NAK Status not set correctly in USB Status Register The EP4 NAK status bit is not set in the USB Status Register (REG4032h]) when the S1D13A04 responds to an IN request on EP4 with a NAK. As a result, a local CPU receiving an "EP4 Packet Transmitted" interrupt may mistakenly believe a bus error occurred in the most recently transmitted packet. Work Around Disable the EP4 Packet Transmitted interrupt when no data is queued for transmission to the local CPU. The basic flow is: In Chip Initialization Code Do not enable `EP4 Packet Transmitted' bit in Interrupt Enable Register 0 (REG[4002h]). When Local Side Wishes to Send Data 1. Put data to transmit in FIFO. 2. Enable `EP4 Packet Transmitted' bit in Interrupt Enable Register 0. 3. Set FIFO Valid (if using FIFO Valid Mode == TRUE). See Section 10.4.2 on page 107 for more information on setting the FIFO Valid. 4. Clear `EP4 Packet Transmitted' status bit in Interrupt Status Register 0 (REG[4004]). Note Step 4 is time-critical. It must be performed within 5 s after Step 3. In Packet Transmitted Interrupt Routine Disable `EP4 Packet Transmitted' bit in Interrupt Enable Register 0. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 107 10.4.2 Write to EP4 FIFO Valid bit cleared by NAK After the local CPU sets EP4 FIFO Valid (in Endpoint 4 FIFO Status Register, REG[402Ch]), the S1D13A04 will erroneously clear the EP4 valid bit if the S1D13A04 is concurrently sending a NAK handshake in response to a previous IN token to EP4. Work Around The work-around is in the `EP4 Packet Transmitted' interrupt routine. It requires the interrupt routine to know whether the recently queued packet was a zero-length packet or not, so that must be stored as a bit when the packet was loaded into the FIFO. On entry to the `EP4 Packet Transmitted' interrupt routine: For a non-zero-length Packet Check the FIFO count. If it is non-zero, this error occurred. In that case, set FIFO Valid again, clear the interrupt status bit, and exit the interrupt routine. For a zero-length Packet Check the Software EOT bit (in Control Register, REG[4000h]). If it is set, the FIFO Valid write failed. In that case, set FIFO Valid again, clear the interrupt status bit, and exit the interrupt routine 10.4.3 EP3 Interrupt Status bit set by NAKs When receiving Bulk OUT packets from a Host PC, the S1D13A04 "Endpoint 3 Interrupt Status" interrupt typically is used to notify the peripheral firmware that a packet has been received. This bit also serves as the "Receive FIFO Valid" bit, so additional packets addressed to Endpoint 3 are NAKed until this status bit is cleared. Once cleared, however, it may become set by another packet which is NAKed by the S1D13A04, causing the Receive FIFO to become "Valid" again. The Host PC may immediately attempt to retransmit the NAKed packet. The firmware should be written to prevent a cycle in which the FIFO is "Valid" each time that the Host PC sends an OUT packet. The following rules govern the S1D13A04's behavior regarding packets received on Endpoint 3: Rule A. At the end of a received OUT token to EP3 (and before the data is received), the S1D13A04 decides to NAK the packet if the "EP3 Interrupt Status" bit is set, and will therefore throw away data received. Rule B. At the end of a received packet (including one which is NAKed), the S1D13A04 sets the "EP3 Interrupt Status" bit. Rule C. Local firmware should clear the "EP3 Interrupt Status" bit after reading all bytes out of the EP3 Receive FIFO. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 108 Epson Research and Development Vancouver Design Center The following figure shows how a repeating cycle of NAKed OUT packets may occur. Host Device OUT Data0 pkt ACK OUT Data1 pkt NAK OUT Data1 pkt NAK IRQ# 1 2 3 4 5 Figure 10-6: Firmware Looping Continuously on Received OUT packets At Point 1, the EP3 Interrupt activates because a packet has been received. In response, the firmware reads the bytes out of the packet and clears the interrupt at Point 2. A second packet is already being received at Point 2, and the S1D13A04 has already decided to NAK this packet due to Rule A. At point 3, the S1D13A04 has NAKed the packet and asserts the Interrupt status bit. Again, the local firmware responds to the interrupt, and seeing it is only a "NAK" interrupt, clears the interrupt condition at Point 4. However, the Host PC has begun to retry the second packet already, so the packet will again get NAKed due to Rule B. This cycle could continue until something changes the flow of OUT packets - for instance, an SOF at the beginning of the next frame, or packet traffic directed at another device or endpoint. Work Around The normal program flow for a packet which the S1D13A04 NAKs is as follows: 1. S1D13A04 asserts IRQ# after NAKing a received packet on EP3. 2. Local CPU is interrupted, enters interrupt routine. 3. Local CPU reads Interrupt Status Register 0 (REG[4004h]) and sees "EP3 Packet Received" interrupt bit. 4. Local CPU reads USB Status Register (REG[4032h]) and sees "NAK" bit set. 5. Local CPU clears Interrupt Status Register 0 (REG[4004h]) "EP3 Packet Status" interrupt bit. 6. Local CPU clears USB Status Register (REG[4032]) "NAK" bit. The technique for avoiding this potential pitfall depends on the speed of the peripheral CPU. The critical timing parameter is the time from the S1D13A04 asserting IRQ# to the firmware clearing the "EP3 Packet Received" bit in Interrupt Status Register 0. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 109 For a Fast CPU A CPU which can clear the Interrupt Status Register 0 bit within 10 msec after the S1D13A04 asserts the IRQ# signal requires no extra code to prevent the potential cycling. In this case, the CPU is fast enough to clear a NAKed packet's Interrupt Status Register 0 bit before another packet can be received. For a Slow CPU A CPU which can't meet the timing requirements for a fast CPU above will require some additional firmware to eliminate the potential for this cycle. After successfully receiving a packet on Endpoint 3 and emptying received data out of the FIFO, the firmware should follow the flow in the following figure. Part of Endpoint 3 Interrupt Service Routine (after FIFO has been emptied) Clear USB Status Register ACK and NAK (bits 1 and 2) Set Timout (calculate for 50 ms) Read USB Status Register Note: Each cycle of this loop should take less than 10 ms Yes NAK (bit 2) set? No Decrement Timeout Timeout == 0? No Yes Clear "Endpoint 3 Interrupt Status" in Interrupt Status Register 0 (bit 3) Clear "USB Endpoint 3 NAK" in USB Status Register (bit 2) Figure 10-7: Endpoint 3 Program Flow for Slow CPU Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 110 Epson Research and Development Vancouver Design Center 10.4.4 "EP2 Valid Bit" in USB Status can be erroneously set by firmware "Endpoint 2 Valid" is the only bit in USB Status which is not written as a "Yes/CLR" bit. Therefore, the firmware must do a read-modify-write sequence when clearing other bits in Interrupt Status Register 0 (REG[4004h]), to preserve the state of "Endpoint 2 Valid". However, this read-modify-write could lead to erroneously setting the EP2 Valid bit if the following sequence occurs with "EP2 Valid" set True: 1. Firmware reads Interrupt Status Register 0 to do a read-modify-write 2. Data from EP2 is sent to Host PC, causing S1D13A04 to clear EP2 Valid 3. Firmware writes modified value to Interrupt Status Register 0 In this case, the firmware has set EP2 Valid in Step 3 after it was cleared by the Host PC, erroneously validating EP2 for the next IN token from the Host. Work Around First, the firmware should do the read-modify-write operation as described above anytime it is modifying bits in "USB Status". Second, when the firmware recognizes an interrupt for "EP2 Packet Transmitted", it should immediately write a `0' to USB Status Register. This will clear the EP2 Valid bit in the unlikely event that it was erroneously set during a read-modify-write operation. 10.4.5 Setting EP4 FIFO Valid bit while NAKing IN token Bit 5 of REG[402Ch] indicates to the S1D13A04 controller when data in the endpoint 4 FIFO is ready to be transferred to the host computer. Changing the state of this bit at certain times may generate an error. When the S1D13A04 USB controller receives an endpoint 4 IN request and endpoint 4 is not ready to transmit data (REG[402Ch] bit 5 = 0), the response is a NAK packet. If endpoint 4 is toggled to a ready to transmit state just before a NAK response packet is sent, the controller may erroneously send a zero length packet instead. When this happens, the data toggle state will be incorrectly set for the next endpoint 4 data transmit. The following timing diagram shows the error occurring in section 3. 1 Host to Device Device to Host CPU Write to EP4_VALID = 1 IN EP4 Token PKT NAK RPLY 2 IN EP4 Token PKT DATA PKT RPLY 3 IN EP4 Token PKT ZERO Length PKT S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 111 This unexpected occurrence of a zero length packet may cause file system handling errors for some operating systems. Work Around There are two software solutions for this occurrence. Disable USB Receiver before setting the EP4 FIFO Valid bit The first solution involves disabling the USB receiver to avoid responding to an EP4 IN packet. During the time the USB receiver is disabled the EP4 FIFO Valid bit is set. When the local CPU is ready to send data on endpoint 4 the steps to follow are: 2. 3. 4. 5. 6. Note Disable the USB differential input receiver (REG[4040h] bit 6 = 0) Wait a minimum of 1s. If needed, delays may be added Enable the EP4 FIFO Valid bit (REG[402Ch] bit 5 = 1) Clear the EP4 Interrupt status bit (REG[4004h] bit 4 = 1) Enable the USB differential input receiver (REG[4040h] bit 6 = 1) Steps 1 through 5 are time critical and must be performed in less than 6 s. Note To comply with "EP4 NAK Status not set correctly in USB Status register", steps 3 and 4 must be completed within 5 s of each other. For further information on "EP4 NAK Status not set correctly in USB Status register", see Section 10.4.1, "EP4 NAK Status not set correctly in USB Status Register" . EP4 FIFO Valid bit set after NAK and before the next IN token The second solution is to wait until immediately after the USB has responded to an IN request with a NAK packet before setting the transmit FIFO valid bit. This solution is recommended only for fast processors. When the local CPU is ready to send data on endpoint 4, it must first detect that a NAK packet has been sent. This is done by reading the EP4 Interrupt Status bit (REG[4004h] bit 4). If the EP4 FIFO Valid bit was not set, the EP4 Interrupt Status bit is set only if a NAK packet has been sent. When the local CPU detects the NAK it must immediately set the EP4 FIFO Valid bit (before responding to the next IN token). After filling the EP4 FIFO the steps to follow before setting the EP4 FIFO Valid bit are: 1. Clear the EP4 Interrupt Status bit (REG[4004h] bit 4) 2. Read the EP4 Interrupt Status bit (REG[4004h] bit 4) until it is set 3. Set the EP4 FIFO Valid bit (REG[402Ch] bit 5 = 1) The setting of the EP4 FIFO Valid bit is time critical. The EP4 FIFO Valid bit must be set within 3 s after the EP4 Interrupt Status has been set internally by the S1D13A04. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 112 Epson Research and Development Vancouver Design Center 11 Hardware Abstraction Layer 11.1 Introduction The S1D13A04 Hardware Abstraction Layer (HAL) is a collection of routines intended to simplify the programming for the S5U13A04B00C evaluation board. Programmers can use the HAL to assist in rapid software prototyping for the S5U13A04B00C evaluation board. The HAL routines are divided into discrete functional blocks. The functions for startup and clock control offer specific support for the S5U13A04B00C evaluation board, while other routines demonstrate memory and register access techniques. For a complete list, see Table 11-1:, "HAL Library API" . 11.2 API for the HAL Library The following table lists the functions provided by the S1D13A04 HAL library. Table 11-1: HAL Library API Function Startup halAcquireController halInitController This routine loads the driver required to access the S1D13A04, locates the and returns the address of the controller. Initializes the controller for use. This includes setting the programmable clock and initializing registers as well as setting the lookup table and clearing video memory. Memory Access halReadDisplay8 halReadDisplay16 halReadDisplay32 halWriteDisplay8 halWriteDisplay16 halWriteDisplay32 halReadReg8 halReadReg16 halReadReg32 halWriteReg8 halWriteReg16 halWriteReg32 halSetClock halGetClock halGetVersionInfo halGetLastError halInitLUT Reads one byte from display memory Reads one word from display memory Reads one double word from display memory Writes one byte to display memory Writes on word to display memory Writes on double word to display memory Register Access Reads one byte from a control register Reads one word from a control register Reads one dword from a control register Writes one byte to a control register Writes one word to a control register Writes one dword to a control registers Clock Support Programs the ICD2061A Programmable Clock Generator. Returns the frequency of the requested ICD2061A clock Miscellaneous Returns a standardized startup banner message Returns the numerical value of the last error and optionally an ASCII string describing the error This routine sets the LUT to uniform values for color/mono panels at all color depths Description S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 113 11.2.1 Startup Routines There are two routines dedicated to startup and initializing the S1D13A04. Typically these two functions are the first two HAL routines a program will call. The startup routines locate the S1D13A04 controller and initialize HAL data structures. As the name suggests, the initialization routine prepares the S1D13A04 for use. Splitting the startup functionality allows programs to start and locate the S1D13A04 but delay or possibly never initialize the controller. Boolean halAcquireController(UInt32 * pMem, UInt32 * pReg) Description: This routine initializes data structures and initiates the link between the application software and the hardware. When the S1D13A04 HAL is used this routine must be the first HAL function called. On PCI platforms, the routine attempts to load the S1D13xxx driver. If the driver loads successfully then a check is made for the existence of an S1D13A04. Parameters: pMem Pointer to an unsigned 32-bit integer which will receive the offset to the first byte of display memory. The offset may be cast to a pointer to access display memory. Pointer to an unsigned 32-bit integer which will receive the offset to the first byte of register space. The offset may be cast to a pointer and to access S1D13A04 registers. On Win32 systems the returned offsets correspond to a linear addresses within the callers address space. Return Value: TRUE (non-zero) if the routine is able to locate an S1D13A04. pMem will contain the offset to the first byte of display memory. pRegs will contain the address of the first 13A04 control register. (zero) if an S1D13A04 is not located. pMem and pRegs will be undefined. If additional error information is required call halGetLastError(). pReg FALSE Note 1. This routine must be called before any other HAL routine is called. 2. For programs written for the S1D13A04 evaluation board, an application may call this routine to obtain pointers to the registers and display memory and then perform all S1D13A04 accesses directly. 3. This routine does not modify S1D13A04 registers or memory. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 114 Epson Research and Development Vancouver Design Center Boolean halInitController(UInt32 Flags) Description: This routine performs the initialization portion of the startup sequence. Initialization of the S1D13A04 evaluation board consists of several steps: - Program the ICD2061A clock generator - Set the initial state of the control - Set the LUT to its default value - Clear video memory All display memory and nearly every control register can or will be affected by the initialization. Any, or all, of the initialization steps may be bypassed according to values contained in the Flags parameter. This allows for conditional run-time changes to the initialization. Parameters: Flags contains initialization specific information. The default action of the HAL is to perform all initialization steps. Flags contain specific instructions for bypassing certain initialization steps. The values for Flags are: fDONT_RESET The first step of the initialization process is to perform a software. Setting this flag bypasses the software reset. fDONT_SET_CLOCKS Setting this flag causes initialization to skip programming the ICD2061A clock generator. Normally the clock on the S5U13A04B00C is programmed to configured values during initialization. fDONT_INIT_REGS Bypass register initialization. Normally the init process sets the register values to a known state. Setting this flag bypasses this step. fDONT_INIT_LUT Bypass look-up table initialization. fDONT_CLEAR_MEM The final step of the initialization process is to clear video display memory. Setting this flag will bypass this step. Return Value: TRUE FALSE (non-zero) if the initialization was successful. (zero) if the HAL was unable to initialize the S1D13A04 If additional error information is required call halGetLastError() S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 115 11.2.2 Memory Access The S1D13A04 HAL includes six memory access functions. The primary purpose of the memory access functions is to demonstrate how to access display memory using the C programming language. Most programs that need to access memory will bypass the HAL and access memory directly. UInt8 halReadDisplay8(UInt32 Offset) Description: Parameters: Return Value: Reads and returns the value of one byte of display memory. Offset A 32 bit offset to the byte to be read from display memory The value of the byte at the requested offset. UInt16 halReadDisplay16(UInt32 Offset) Description: Parameters: Reads and returns the value of one word of display memory. Offset A 32 bit byte offset to the word to be read from display memory To prevent system slowdowns and possibly memory faults, Offset should be a word multiple. Return Value: The value of the word at the requested offset. UInt32 halReadDisplay32(UInt32 Offset) Description: Parameters: Reads and returns the value of one dword of display memory. Offset A 32 bit byte offset to the dword to be read from display memory. To prevent system slowdowns and possibly memory faults, Offset should be a dword multiple. Return Value: The value of the dword at the requested offset. void halWriteDisplay8(UInt32 Offset, UInt8 Value, UInt32 Count) Description: Parameters: Writes a byte into display memory at the requested address. Offset Value Count Return Value: Nothing. A 32 bit byte offset to the byte to be written to display memory. The byte value to be written to display memory. The number of times to repeat Value in memory. By including a count (or loop) value this function can efficiently fill display memory. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 116 Epson Research and Development Vancouver Design Center void halWriteDisplay16(UInt32 Offset, UInt16 Value, UInt32 Count) Description: Parameters: Writes a word into display memory at the requested offset. Offset a 32 bit byte offset to the byte to be written to display memory. To prevent system slowdowns and possibly memory faults, Offset should be a word multiple. the word value to be written to display memory. the number of times to repeat the Value in memory. By including a count (or loop) value this function can efficiently fill display memory. Value Count Return Value: Nothing. void halWriteDisplay32(UInt32 Offset, UInt32 Value, UInt32 Count) Description: Parameters: Writes a dword into display memory at the requested offset. Offset A 32 bit byte offset to the byte to be written to display memory. To prevent system slowdowns and possibly memory faults, Offset should be a dword multiple. The dword value to be written to display memory. The number of times to repeat the Value in memory. By including a count (or loop) value this function can efficiently fill display memory. Value Count Return Value: Nothing. 11.2.3 Register Access The S1D13A04 HAL includes six register access functions. The primary purpose of the register access functions is to demonstrate how to access the S1D13A04 control registers using the C programming language. Most programs that need to access the registers will bypass the HAL and access the registers directly. UInt8 halReadReg8(UInt32 Index) Description: Parameters: Reads and returns the contents of one byte of an S1D13A04 register at the requested offset. No S1D13A04 registers are changed Index 32 bit offset to the register to read. Index is zero based from the beginning of register address space. (e.g. if Index == 04h then the Memory Clock Configuration register will be read and if Index == 8000h then the BitBLT Control Register will be read) Return Value: The value read from the register. Use caution in selecting the index and when interpreting values returned from halReadReg8() to ensure the correct meaning is given to the values. Changing between big endian and little endian will move relative register offsets. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 117 UInt16 halReadReg16(UInt32 Index) Description: Parameters: Reads and returns the contents of one word of an S1D13A04 register at the requested offset. No S1D13A04 register are changed. Index 32 bit offset to the register to read. Index is zero based from the beginning of register address space. (e.g. if Index == 04h then the Memory Clock Configuration register will be read and if Index == 8000h then the BitBLT Control Register will be read) Return Value: The word value read from the register. Use caution in determining the index and interpreting the values returned from halReadReg16() to ensure the correct meaning is given to the values. Changing between big and little endian will move relative register offsets resulting in different values. UInt16 halReadReg32(UInt32 Index) Description: Parameters: Reads and returns the dword value of an S1D13A04 register at the requested offset. No S1D13A04 register are changed. Index 32 bit offset to the register to read. Index is zero based from the beginning of register address space. (e.g. if Index == 04h then the Memory Clock Configuration register will be read and if Index == 8000h then the BitBLT Control Register will be read) Return Value: The dword value read from the register. void halWriteReg8(UInt32 Index, UInt8 Value) Description: Parameters: Writes an 8 bit value to the register at the requested offset. Index 32 bit offset to the register to write. Index is zero based from the beginning of register address space. (e.g. if Index == 04h then the Memory Clock Configuration register will be written to and if Index == 8000h then the BitBLT Control Register will be written to) The byte value to write to the register. Changing between big and little endian will move relative register offsets. Use caution in interpreting the index and values to write to registers using the halWriteReg8() function to ensure that register are programmed correctly. Value Return Value: Nothing. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 118 Epson Research and Development Vancouver Design Center void halWriteReg16(UInt32 Index, UInt16 Value) Description: Parameters: Writes a 16 bit value to the S1D13A04 register at the requested offset. Index 32 bit byte offset to the register to write. Index is zero based from the beginning of register address space. (e.g. if Index == 04h then the Memory Clock Configuration register will be written to and if Index == 8000h then the BitBLT Control Register will be written to) The word value to write to the register. Value Return Value: Nothing. Changing between big and little endian will move relative register offsets. Use caution in interpreting the index and values to write to registers using the halWriteReg8() function to ensure that register are programmed correctly. void halWriteReg32(UInt32 Index, UInt32 Value) Description: Parameters: Writes a 32 bit value (dword) to the register at the requested offset. Index 32 bit byte offset to the register to write. Index is zero based from the beginning of register address space. (e.g. if Index == 04h then the Memory Clock Configuration register will be written to and if Index == 8000h then the BitBLT Control Register will be written to) The dword value to write to the register. Value Return Value: Nothing. 11.2.4 Clock Support To maximize flexibility, S1D13A04 evaluation boards include a programmable clock. The following HAL routines provide support for the programmable clock. Boolean halSetClock(UInt32 ClkiFreq, UInt32 Clki2Freq) Description: Parameters: This routine program the ICD2061A programmable clock generator to the specified frequency. ClkiFreq Clki2Freq The desired frequency, in Hz, for CLKI. The desired frequency, in Hz, for CLKI2. dwFrequencyThe desired frequency (in Hz). Return Value: TRUE (non-zero) if the function was successful in setting the clock. FALSE (zero) if there was an error detected while trying to set the clock. If additional error information is required call halGetLastError(). S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 119 UInt32 halGetClock(CLOCKSELECT Clock) Description: Parameters: Return Value: Returns the frequency of the clock input identified by 'Clock'. Clock Indicates which clock to read. This value can be CLKI or CLKI2. The frequency, in Hz, of the requested clock. 11.2.5 Miscellaneous The miscellaneous function are an assortment of routines, determined to be beneficial to a number of programs and hence warranted being included in the HAL. void halGetVersionInfo(const char * szProgName, const char * szDesc, const char * szVersion, char * szRetStr, int nLength) Description: This routine creates a standardized startup banner by merging program and HAL specific information. The newly formulated string is returned to the calling program for display. The final formatted string will resemble: 13A04PROGRAM - Internal test and diagnostic program - Build: 1234 [HAL: 1234] Copyright (c) 2000,2001 Epson Research and Development, Inc. All Rights Reserved. Parameters: szProgName Pointer to an ASCIIZ string containing the name of the program. (e.g. "PROGRAM") szDesc szVersion Pointer to an ASCIIZ string containing a description of what this program is intended to do. (e.g. "Internal test and diagnostic program") Pointer to an ASCIIZ string containing the build info for this program. This should be the revision info string as updated by VSS. (e.g. "$Revision: 30 $") Pointer to a buffer into which the product and version information will be formatted into. Total number of bytes in the string pointed to by szRetStr. This function will write nLength or fewer bytes to the buffer pointed to by szRetStr. szRetStr nLength Return Value: Nothing. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 120 Epson Research and Development Vancouver Design Center int halGetLastError(char * ErrMsg, int MaxSize) Description: This routine retrieves the last error detected by the HAL. Parameters: ErrMsg When halGetLastError() returns ErrMsg will point to the textual error message. If ErrMsg is NULL then only the error code will be returned. MaxSize Maximum number of bytes, including the final '\0' that can be placed in the string pointed to by ErrMsg. Return Value:The numerical value of the internal error number. HALEXTERN void halInitLUT(void) Description: To standardize the appearance of test and validation programs, it was decided the HAL would have the ability to set the lookup table to uniform values. The routine cracks the color depth and display type to determine which LUT values to use and proceeds to write the LUT entries. Parameters: None Return Value: Nothing. S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 121 12 Sample Code Example source code demonstrating programming the S1D13A04 using the HAL library is available on the internet at www.erd.epson.com. Programming Notes and Examples Issue Date: 2002/08/21 S1D13A04 X37A-G-003-05 Page 122 Epson Research and Development Vancouver Design Center 13 Sales and Technical Support Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp/ North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com/ Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk/ Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de/ S1D13A04 X37A-G-003-05 Programming Notes and Examples Issue Date: 2002/08/21 Epson Research and Development Vancouver Design Center Page 1 READ-ONLY CONFIGURATION REGISTERS Product Information Register REG[00h] Default = 2Cxx282Ch Product Code 31 30 29 28 27 26 Revision Code 25 24 n/a 23 22 CNF[6:4] Status 21 20 Reserved 19 18 Read Only CNF[2:0] Status 17 16 Display Buffer Size 15 14 13 12 11 10 9 8 7 6 Product Code 5 4 3 2 Revision Code 1 0 CLOCK CONFIGURATION REGISTERS Memory Clock Configuration Register REG[04h] Default = 00000000h n/a 31 30 29 28 27 n/a 15 14 13 12 Default = 00000000h n/a 31 30 29 28 27 n/a 15 14 13 12 11 10 9 8 7 6 26 25 24 23 22 21 PCLK Divide Select 5 4 3 20 19 n/a 2 18 17 16 11 10 9 8 7 6 26 25 24 23 22 21 20 19 18 Reserved 3 2 1 0 Read/Write 17 16 Read/Write MCLK Divide Select 5 4 Pixel Clock Configuration Register REG[08h] PCLK Source Select 1 0 PANEL CONFIGURATION REGISTERS Panel Type & MOD Rate Register REG[0Ch] Default = 00000000h n/a 31 30 29 28 27 26 25 24 23 Panel Data Format Select 11 10 9 8 7 22 Color/ Mono Panel Select 6 21 20 19 `Direct' HR-TFT Res Select 3 MOD Rate 18 17 16 Read/Write n/a Panel Data Width n/a Panel Type 15 14 13 12 Default = 00000000h n/a 5 4 2 1 0 Read/Write Display Settings Register REG[10h] Pixel Doubling Vertical 28 27 26 n/a 25 Pixel Doubling Horiz. 24 Display Blank 23 Dithering Disable 22 n/a 21 SW Video Invert 20 PIP+ Window Enable 19 n/a 18 SwivelView Mode Select 17 16 31 30 29 Bits-per-pixel Select (actual value: 1, 2, 4, 8, 16 bpp) 9 8 7 6 5 4 3 2 1 0 Read/Write n/a 15 14 13 12 11 10 Power Save Configuration Register REG[14h] Default = 00000010h 31 30 29 28 27 26 25 24 23 VNDP Status (RO) 22 Memory Power Save Status (RO) 6 21 20 Power Save Enable 4 19 18 17 16 `Direct' HR-TFT GPO Control n/a n/a n/a 15 14 13 12 11 10 9 8 7 5 3 2 1 0 LOOK-UP TABLE REGISTERS Look-Up Table Write Register REG[18h] Default = 00000000h LUT Write Address 31 30 29 28 27 26 25 n/a 11 10 9 8 7 6 24 23 22 LUT Red Write Data 21 20 19 18 17 n/a 3 2 1 0 Write Only n/a 16 LUT Green Write Data 15 14 13 12 Default = 00000000h LUT Read Address (write only) 31 30 29 28 27 26 25 LUT Blue Write Data 5 4 Look-Up Table Read Register REG[1Ch] Write Only (bits 31-24)/Read Only LUT Red Read Data 24 n/a 11 10 9 8 7 6 23 22 21 20 19 18 17 n/a 3 2 1 0 n/a 16 LUT Green Read Data 15 14 13 12 LUT Blue Read Data 5 4 Register Summary Issue Date: 01/10/02 S1D13A04 X37A-R-001-01 Page 2 Epson Research and Development Vancouver Design Center DISPLAY MODE REGISTERS Horizontal Total Register REG[20h] Default = 00000000h n/a 31 30 29 28 27 n/a 15 14 13 12 Default = 00000000h n/a 31 30 29 28 27 n/a 15 14 13 12 11 10 9 8 7 6 5 26 25 24 23 22 21 20 19 18 17 16 11 10 9 8 7 6 5 4 26 25 24 23 22 21 20 19 Horizontal Total bits 6-0 3 2 1 0 Read/Write 18 17 16 Read/Write Horizontal Display Period Register REG[24h] Horizontal Display Period bits 6-0 4 3 2 1 0 Read/Write n/a Horizontal Display Period Start Position Register REG[28h] Default = 00000000h 31 30 29 n/a 28 27 26 25 24 23 22 21 20 19 18 17 16 Horizontal Display Period Start Position bits 9-0 12 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write FPLINE Polarity 27 26 25 24 23 22 21 FPLINE Pulse Width bits 6-0 20 19 18 17 16 15 FPLINE Register REG[2Ch] 14 13 Default = 00000000h n/a 31 30 29 n/a 28 FPLINE Pulse Start Position bits 9-0 12 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write n/a 15 14 13 Vertical Total Register REG[30h] Default = 00000000h 31 30 29 n/a 28 27 26 25 24 23 22 21 20 19 18 17 16 Vertical Total bits 9-0 12 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write n/a 15 14 13 Vertical Display Period Register REG[34h] Default = 00000000h 31 30 29 n/a 28 27 26 25 24 23 22 21 20 19 18 17 16 Vertical Display Period bits 9-0 12 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write n/a 15 14 13 Vertical Display Period Start Position Register REG[38h] Default = 00000000h 31 30 29 n/a 28 27 26 25 24 23 22 21 20 19 18 17 16 Vertical Display Period Start Position bits 9-0 12 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write FPFRAME Polarity 27 26 25 24 23 22 21 n/a 20 19 18 FPFRAME Pulse Width bits 2-0 17 16 15 14 13 FPFRAME Register REG[3Ch] Default = 00000000h n/a 31 30 29 n/a 28 FPFRAME Pulse Start Position bits 9-0 12 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write n/a bit 16 23 22 21 20 19 18 17 16 15 14 13 Main Window Display Start Address Register REG[40h] Default = 00000000h 31 30 29 28 27 26 25 24 Main Window Display Start Address bits 15-0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write n/a 31 30 29 n/a 15 14 13 12 11 10 9 8 7 28 27 26 25 24 23 22 21 20 19 18 17 16 Main Window Line Address Offset Register REG[44h] Default = 00000000h Main Window Line Address Offset bits 9-0 6 5 4 3 2 1 0 S1D13A04 X37A-R-001-01 Register Summary Issue Date: 01/10/02 Epson Research and Development Vancouver Design Center Page 3 PICTURE-IN-PICTURE PLUS (PIP+) REGISTERS PIP+ Display Start Address Register REG[50h] Default = 00000000h n/a 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 Read/Write bit 16 16 PIP+ Window Display Start Address bits 15-0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write n/a 31 30 29 n/a 15 14 13 12 Default = 00000000h n/a 31 30 29 n/a 15 14 13 12 Default = 00000000h n/a 31 30 29 n/a 15 14 13 12 11 10 9 8 7 6 28 27 26 25 24 23 22 PIP+ Window Y End Position bits 9-0 21 20 19 18 17 16 11 10 9 8 7 6 28 27 26 25 24 23 22 PIP+ Window X End Position bits 9-0 21 20 19 18 17 16 11 10 9 8 7 28 27 26 25 24 23 22 21 20 19 18 17 16 PIP+ Window Line Address Offset Register REG[54h] Default = 00000000h PIP+ Window Line Address Offset bits 9-0 6 5 4 3 2 1 0 Read/Write PIP+ Window X Positions Register REG[58h] PIP+ Window X Start Position bits 9-0 5 4 3 2 1 0 Read/Write PIP+ Window Y Positions Register REG[5Ch] PIP+ Window Y Start Position bits 9-0 5 4 3 2 1 0 MISCELLANEOUS REGISTERS Special Purpose Register REG[60h] Default = 00000000h n/a 31 30 29 28 n/a 15 14 13 12 Default = 00000000h GPIO4 Input Enable 28 n/a 15 14 13 12 11 10 9 8 GPIO3 Input Enable 27 GPIO2 Input Enable 26 GPIO1 Input Enable 25 GPIO0 Input Enable 24 GPIO7 Config 23 GPIO7 Status 7 GPIO6 Config 22 GPIO6 Status 6 GPIO5 Config 21 GPIO5 Status 5 GPIO4 Config 20 GPIO4 Status 4 GPIO3 Config 19 GPIO3 Status 3 GPIO2 Config 18 GPIO2 Status 2 GPIO1 Config 17 GPIO1 Status 1 11 10 9 8 27 26 25 24 23 2D Byte Swap 7 22 Display Data Word Swap 6 21 Display Data Byte Swap 5 4 20 n/a 3 Reserved 19 18 Latch Byte Select 2 1 17 n/a 0 Read/Write GPIO0 Config 16 GPIO0 Status 0 Read/Write n/a 31 30 29 28 n/a 15 14 13 12 11 10 9 8 7 27 26 25 24 23 22 21 20 19 PWM Clock Force High 4 3 18 17 16 PWM Clock Enable 0 Read/Write n/a 31 30 29 28 n/a 15 14 13 12 11 10 9 8 7 6 5 27 26 25 24 23 22 21 20 19 18 17 16 16 Read/Write GPIO Status and Control Register REG[64h] GPIO7 Input Enable 31 GPIO6 Input Enable 30 GPIO5 Input Enable 29 Brightness (PWM) Configuration Register REG[70h] Default = 00000000h PWM Clock Divide Select bits 3-0 6 5 PWMCLK Source Select bits 1-0 2 1 Brightness (PWM) Duty Cycle Register REG[74h] Default = 00000000h PWMOUT Duty Cycle bits 7-0 4 3 2 1 0 Read/Write Scratch Pad A bits 31-24 Scratch Pad A Register REG[80h] Default = not applicable 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 Scratch Pad A bits 15-0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write Scratch Pad B bits 31-24 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 Scratch Pad B Register REG[84h] Default = not applicable Scratch Pad B bits 15-0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write Scratch Pad C bits 31-24 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 Scratch Pad C Register REG[88h] Default = not applicable Scratch Pad C bits 15-0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Register Summary Issue Date: 01/10/02 S1D13A04 X37A-R-001-01 Page 4 Epson Research and Development Vancouver Design Center USB REGISTERS Control Register REG[4000h] Default = 00h n/a 15 14 13 12 Default = 00h Suspend Request Interrupt Enable 11 10 9 8 7 SOF Interrupt Enable 6 Endpoint 4 Interrupt Enable 4 Endpoint 3 Interrupt Enable 3 Endpoint 2 Interrupt Enable 2 Endpoint 1 Interrupt Enable 1 11 10 9 8 USBClk Enable 7 Software EOT 6 USB Enable 5 Endpoint 4 Stall 4 Endpoint 3 Stall 3 USB Setup 2 Reserved 1 Read/Write Reserved 0 Read/Write Interrupt Enable Register 0 REG[4002h] n/a Reserved n/a 15 14 13 12 Default = 00h 5 0 Read/Write Interrupt Status Register 0 REG[4004h] n/a Suspend Request Interrupt Status 11 10 9 8 7 SOF Interrupt Status 6 Reserved Endpoint 4 Interrupt Status 4 Endpoint 3 Interrupt Status 3 Endpoint 2 Interrupt Status 2 Endpoint 1 Interrupt Status 1 Upper Interrupt Active (read only) 0 Read/Write 15 14 13 12 Default = 00h 5 Interrupt Enable Register 1 REG[4006h] n/a Transmit FIFO Almost Empty Interrupt Enable 8 7 6 5 4 3 2 1 Receive FIFO Almost Full Interrupt Enable 0 Read/Write 15 14 13 12 Default = 00h 11 10 9 Interrupt Status Register 1 REG[4008h] n/a Transmit FIFO Almost Empty Status 8 7 6 5 4 3 2 1 Receive FIFO Almost Full Status 0 Read/Write 15 14 13 12 Default = 00h 11 10 9 Endpoint 1 Index Register REG[4010h] n/a 15 14 13 12 11 10 9 8 7 6 5 4 3 2 Endpoint 1 Index bits 2-0 1 0 Read Only Endpoint 1 Receive Mailbox Data Register REG[4012h] Default = 00h n/a 15 14 13 12 Default = 00h n/a 15 14 13 12 11 10 9 8 7 6 5 4 3 2 11 10 9 8 7 6 5 Endpoint 1 Receive Mailbox Data bits 7-0 4 3 2 1 0 Read/Write Endpoint 2 Index Register REG[4018h] Endpoint 2 Index bits 2-0 1 0 Read/Write Endpoint 2 Transmit Mailbox Data Register REG[401Ah] Default = 00h n/a 15 14 13 12 11 10 9 8 7 6 Endpoint 2 Transmit Mailbox Data bits 7-0 5 4 3 2 1 0 Read/Write Endpoint 2 Interrupt Polling Interval Register REG[401Ch] Default = FFh n/a 15 14 13 12 11 10 9 8 7 6 Endpoint 2 Interrupt Polling Interval bits 7-0 5 4 3 2 1 0 Read Only Endpoint 3 Receive FIFO Data Register REG[4020h] Default = 00h n/a 15 14 13 12 11 10 9 8 7 6 5 Endpoint 3 Receive FIFO Data bits 7-0 4 3 2 1 0 Read Only Endpoint 3 Receive FIFO Count Register REG[4022h] Default = 00h n/a 15 14 13 12 11 10 9 8 7 6 5 Endpoint 3 Receive FIFO Count bits 7-0 4 3 2 1 0 Read/Write Endpoint 3 Receive FIFO Status Register REG[4024h] Default = 01h Receive FIFO Flush 9 8 7 6 5 4 Receive FIFO Underflow 2 Receive FIFO Full (read only) 1 n/a Reserved Receive FIFO Empty (read only) 0 Read/Write 15 14 13 12 11 10 3 Endpoint 3 Maximum Packet Size Register REG[4026h] Default = 08h n/a 15 14 13 12 11 10 9 8 7 6 5 Endpoint 3 Max Packet Size bits 7-0 4 3 2 1 0 Write Only Endpoint 4 Transmit FIFO Data Register REG[4028h] Default = 00h n/a 15 14 13 12 11 10 9 8 7 6 5 Endpoint 4 Transmit FIFO Data bits 7-0 4 3 2 1 0 Read Only Endpoint 4 Transmit FIFO Count Register REG[402Ah] Default = 00h n/a 15 14 13 12 11 10 9 8 7 6 5 Endpoint 4 Transmit FIFO Count bits 7-0 4 3 2 1 0 S1D13A04 X37A-R-001-01 Register Summary Issue Date: 01/10/02 Epson Research and Development Vancouver Design Center Page 5 Endpoint 4 Transmit FIFO Status Register REG[402Ch] Default = 01h Transmit FIFO Valid 10 9 8 7 6 5 Transmit FIFO Flush 4 Transmit FIFO Overflow 3 Transmit FIFO Full (read only) 1 Read/Write Transmit FIFO Empty (read only) 0 Read/Write n/a Endpoint 4 Max Packet Size bits 7-0 11 10 9 8 7 6 5 4 3 2 1 0 Read Only n/a Chip Revision bits 7-0 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write n/a Suspend Control 11 10 9 8 7 USB Endpoint 4 STALL 6 USB Endpoint 4 NAK 5 USB Endpoint 4 ACK 4 USB Endpoint 3 STALL 3 USB Endpoint 3 NAK 2 USB Endpoint 3 ACK 1 Endpoint 2 Valid 0 Read Only n/a Frame Counter bits 10-8 8 7 6 5 4 3 2 1 0 Read Only n/a Frame Counter bits 7-0 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write n/a Extended Register Index bits 7-0 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write n/a Extended Register Data bits 7-0 11 10 9 8 Read/Write 7 6 5 4 Default = B8h Vendor ID bits 7-0 2 1 0 Read/Write 7 6 5 4 Default = 21h Product ID bits 7-0 2 1 0 Read/Write 7 6 5 4 Default = 00h Release Number bits 7-0 2 1 0 Read/Write 7 6 5 4 3 2 1 0 Read/Write 3 2 1 0 Read/Write 3 2 1 0 Read/Write 3 2 1 0 Read/Write n/a Reserved 15 14 13 12 11 2 Endpoint 4 Maximum Packet Size Register REG[402Eh] Default = 08h 15 14 13 12 Default = 01h Revision Register REG[4030h] 15 14 13 12 Default = 00h USB Status Register REG[4032h] 15 14 13 12 Default = 00h Frame Counter MSB Register REG[4034h] 15 14 13 12 Default = 00h 11 10 9 Frame Counter LSB Register REG[4036h] 15 14 13 12 Default = 00h Extended Register Index REG[4038h] 15 14 13 12 Default = 04h Extended Register Data REG[403Ah] 15 14 13 12 Default = 04h Vendor ID MSB REG[403Ah], Index[00h] Vendor ID LSB REG[403Ah], Index[01h] Vendor ID bits 15-8 7 6 5 4 Default = 88h Product ID bits 15-8 7 6 5 4 Default = 01h Release Number bits 15-8 7 6 5 4 3 3 3 Product ID MSB REG[403Ah], Index[02h] Product ID LSB REG[403Ah], Index[03h] Release Number MSB REG[403Ah], Index[04h] Release Number LSB REG[403Ah], Index[05h] Receive FIFO Almost Full Threshold REG[403Ah], Index[06h] Default = 3Ch n/a 7 6 5 Receive FIFO Almost Full Threshold bits 5-0 4 Default = 01h n/a 7 6 5 4 Default = 00h EP2 Data Toggle 5 EP1 Data Toggle 4 Default = 00h n/a 7 6 5 4 Default = 0Dh n/a 15 Reserved REG[4042h] 14 13 12 Default = 1Dh n/a 15 14 13 12 11 10 9 11 10 9 3 2 1 Reserved 3 Reserved 2 n/a 1 3 2 1 3 2 1 Transmit FIFO Almost Empty Threshold REG[403Ah], Index[07h] Default = 04h n/a Transmit FIFO Almost Empty Threshold bits 5-0 6 5 4 Default = FAh Maximum Current bits 7-0 7 6 5 4 Default = 00h n/a 7 6 5 4 3 2 1 3 2 1 3 2 1 0 Read/Write USB String Enable 0 Read/Write Reserved 0 Read/Write Transmit FIFO Valid Mode 0 7 0 Read/Write USB Control REG[403Ah], Index[08h] Maximum Power Consumption REG[403Ah], Index[09h] 0 Read/Write Reserved 0 Packet Control REG[403Ah], Index[0Ah] EP4 Data Toggle 7 EP3 Data Toggle 6 Reserved REG[403Ah], Index[0Bh] FIFO Control REG[403Ah], Index[0Ch] USBFC Input Control Register REG[4040h] Read/Write USCMPEN 8 7 6 Reserved 5 Reserved 4 ISO 3 WAKEUP 2 Reserved 1 Reserved 0 Read Only Reserved 8 7 6 5 4 3 2 1 0 Register Summary Issue Date: 01/10/02 S1D13A04 X37A-R-001-01 Page 6 Epson Research and Development Vancouver Design Center Pin Input Status / Pin Output Data Register REG[4044h] Default = depends on USB input pin state USBDETECT Read/Write Input Pin Status (read only) 8 7 6 5 4 3 2 1 USBPUP Output Pin Status 0 Read/Write n/a 15 14 13 12 11 10 9 Positive Interrupt Enable (Mask) Register REG[4046h] Default = 00h n/a 15 14 13 12 11 10 9 8 7 USBDETECT USBPUP 5 DEVCFG 4 SUSP 3 OSCRUN 2 USBRESET INT 0 Read/Write 6 1 Negative Interrupt Enable (Mask) Register REG[4048h] Default = 00h n/a 15 14 13 12 11 10 9 8 7 USBDETECT USBPUP 5 DEVCFG 4 SUSP 3 OSCRUN 2 USBRESET INT 0 Read/Write 6 1 Positive Interrupt Status/Clear Register REG[404Ah] Default = 00h n/a 15 14 13 12 11 10 9 8 7 USBDETECT USBPUP 5 DEVCFG 4 SUSP 3 OSCRUN 2 USBRESET INT 0 Read/Write 6 1 Negative Interrupt Status/Clear Register REG[404Ch] Default = 00h n/a 15 14 13 12 11 10 9 8 7 USBDETECT USBPUP 5 DEVCFG 4 SUSP 3 OSCRUN 2 USBRESET INT 0 Read Only 6 1 Positive Interrupt Masked Status Register REG[404Eh] Default = 00h n/a 15 14 13 12 11 10 9 8 7 USBDETECT USBPUP 5 DEVCFG 4 SUSP 3 OSCRUN 2 USBRESET INT 0 Read Only 6 1 Negative Interrupt Masked Status Register REG[4050h] Default = 00h n/a 15 14 13 12 Default = 00h n/a 15 14 13 12 Default = 00h n/a 15 14 13 12 11 10 9 8 7 6 5 n/a 4 3 2 11 10 9 8 7 6 USB Software Reset (Code = 10100100) bits 7-0 5 4 3 2 1 11 10 9 8 7 USBDETECT USBPUP 5 DEVCFG 4 SUSP 3 OSCRUN 2 USBRESET INT 0 Write Only 6 1 USB Software Reset Register REG[4052h] 0 Read/Write USB Wait State Register REG[4054h] USB Wait State bits 1-0 1 0 S1D13A04 X37A-R-001-01 Register Summary Issue Date: 01/10/02 Epson Research and Development Vancouver Design Center Page 7 2D ACCELERATION (BitBLT) REGISTERS BitBLT Control Register REG[8000h] Default = 00000000h n/a 31 30 29 28 27 26 25 24 n/a 15 14 13 12 Default = 00000000h Number of Used FIFO Entries 29 28 27 n/a 15 14 13 12 Default = 00000000h n/a 31 30 29 28 27 26 n/a 15 14 13 12 11 10 9 8 7 6 5 4 3 25 24 23 22 21 20 19 11 10 9 8 7 26 25 24 23 n/a 22 FIFO Not Empty 6 21 FIFO Half Full 5 Number of Free FIFO Entries (0 means full) 20 FIFO Full Status 4 3 19 18 n/a 2 1 17 16 BitBLT Busy Status 0 Read/Write BitBLT ROP Code bits 3-0 18 17 16 11 10 9 8 7 6 5 4 3 2 1 23 22 21 20 19 Color Format Select 18 Read/Write Dest Linear Select 17 Source Linear Select 16 BitBLT Enable (WO) 0 Read Only BitBLT Status Register REG[8004h] n/a 31 30 BitBLT Command Register REG[8008h] BitBLT Operation bits 3-0 2 1 0 Read/Write BitBLT Source Start Address Register REG[800Ch] Default = 00000000h n/a 31 30 29 28 27 26 25 24 23 22 21 20 BitBLT Source Start Address bits 20-16 19 18 17 16 BitBLT Source Start Address bits 15-0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write n/a 31 30 29 28 27 26 25 24 23 22 21 20 BitBLT Destination Start Address bits 20-16 19 18 17 16 BitBLT Destination Start Address Register REG[8010h] Default = 00000000h BitBLT Destination Start Address bits 15-0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write n/a 31 30 29 n/a 15 14 13 12 Default = 00000000h n/a 31 30 29 n/a 15 14 13 12 Default = 00000000h n/a 31 30 29 n/a 15 14 13 12 11 10 9 8 7 6 28 27 26 25 24 23 22 21 20 19 18 17 16 11 10 9 8 7 6 28 27 26 25 24 23 22 21 20 19 18 17 16 11 10 9 8 7 28 27 26 25 24 23 22 21 20 19 18 17 16 BitBLT Memory Address Offset Register REG[8014h] Default = 00000000h BitBLT Memory Address Offset bits 10-0 6 5 4 3 2 1 0 Read/Write BitBLT Width Register REG[8018h] BitBLT Width bits 9-0 5 4 3 2 1 0 Read/Write BitBLT Height Register REG[801Ch] BitBLT Height bits 9-0 5 4 3 2 1 0 Read/Write n/a BitBLT Background Color Register REG[8020h] Default = 00000000h 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 BitBLT Background Color bits 15-0 15 14 13 12 Default = 00000000h n/a 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 11 10 9 8 7 6 5 4 3 2 1 0 Read/Write BitBLT Foreground Color Register REG[8024h] BitBLT Foreground Color bits 15-0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 2D Accelerator (BitBLT) Data Memory Mapped Region Register AB16-AB0 = 10000h-1FFFEh, even addressesRead/Write BitBLT Data bits 31-16 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 BitBLT Data bits 15-0 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Register Summary Issue Date: 01/10/02 S1D13A04 X37A-R-001-01 Page 8 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-R-001-01 Register Summary Issue Date: 01/10/02 S1D13A04 LCD/USB Companion Chip 13A04CFG Configuration Program Document Number: X37A-B-001-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 3 Table of Contents 13A04CFG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 S1D13A04 Supported Evaluation Platforms Installation . . . . . . . . . . . . . Usage . . . . . . . . . . . . . . . 13A04CFG Configuration Tabs . . . . . General Tab . . . . . . . . . . . . . . Preferences Tab . . . . . . . . . . . . Clocks Tab . . . . . . . . . . . . . . . Panel Tab . . . . . . . . . . . . . . . . Panel Power Tab . . . . . . . . . . . . Registers Tab . . . . . . . . . . . . . . Direct Tab . . . . . . . . . . . . . . . 13A04CFG Menus . . . . . . . . . . Open... . . . . . . . . . . . . . . . . . Save . . . . . . . . . . . . . . . . . . Save As... . . . . . . . . . . . . . . . . Configure Multiple . . . . . . . . . . . Export . . . . . . . . . . . . . . . . . Enable Tooltips . . . . . . . . . . . . Tooltip Delay . . . . . . . . . . . . . . ERD on the Web . . . . . . . . . . . . Update Common Controls . . . . . . . About 13A04CFG . . . . . . . . . . . Comments . . . . . . . . . . . . . .. .. .. .. ... ... ... ... ... ... ... .. ... ... ... ... ... ... ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. ... ... ... ... ... ... ... .. ... ... ... ... ... ... ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. ... ... ... ... ... ... ... .. ... ... ... ... ... ... ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. ... ... ... ... ... ... ... .. ... ... ... ... ... ... ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. ... ... ... ... ... ... ... .. ... ... ... ... ... ... ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. ... ... ... ... ... ... ... .. ... ... ... ... ... ... ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . . .. .. .. .. ... ... ... ... ... ... ... .. ... ... ... ... ... ... ... ... ... ... .. . . . . . . . . . . . . . . . . . . . . . . . .5 .5 .5 .6 .6 .8 10 14 18 20 21 23 23 24 24 25 26 27 27 27 27 27 28 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 X37A-B-001-01 Page 4 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 5 13A04CFG 13A04CFG is an interactive Windows(R) program that calculates register values for a userdefined S1D13A04 configuration. The configuration information can be used to directly alter the operating characteristics of the S1D13A04 utilities or any program built with the Hardware Abstraction Layer (HAL) library. Alternatively, the configuration information can be saved in a variety of text file formats for use in other applications. S1D13A04 Supported Evaluation Platforms 13A04CFG runs on PC system running Windows 9x/ME/NT/2000 and can modify Win32 .exe files and .s9 format files. Installation Create a directory for 13A04cfg.exe and copy the files 13A04cfg.exe and panels.def to that directory. Panels.def contains configuration information for a number of panels and must reside in the same directory as 13A04cfg.exe. Usage To start 13A04CFG from the Windows desktop, click on the My Computer icon and run the program 13a04cfg.exe from the installed directory. To start 13A04CFG from a Windows command prompt, change to the directory 13A04cfg.exe was installed to and type the command 13A04cfg. The basic procedure for using 13A04CFG is: 1. Start 13A04CFG as described above. 2. Open an existing file to serve as a starting reference point (this step is optional). 3. Modify the configuration. For specific information on editing the configuration, see "13A04CFG Configuration Tabs" on page 6. 4. Save the new configuration. The configuration information can be saved in two ways; as an ASCII text file or by modifying an executable image on disk. Several ASCII text file formats are supported. Most are formatted C header files used to build display drivers or standalone applications. Utility files based on the Hardware Abstraction Layer (HAL) can be modified directly by 13A04CFG. 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 X37A-B-001-01 Page 6 Epson Research and Development Vancouver Design Center 13A04CFG Configuration Tabs 13A04CFG displays a series of tabs which can be selected at the top of the main window. Each tab allows the configuration of a specific aspect of S1D13A04 operation. The following sections describe the purpose and use of each of the tabs. General Tab Decode Addresses Register Address Display Buffer Address Display Data Byte Swap USB Support Clock Chip Support BitBLT Data Byte Swap The General tab contains settings that define the S1D13A04 operating environment. Decode Addresses Selecting one of the listed evaluation platforms changes the values for the "Register address" and "Display buffer address" fields. The values used for each evaluation platform are examples of possible implementations as used by the Epson S5U13A04B00C evaluation board. If your hardware implementation differs from the addresses used, select the User-Defined option and enter the correct values for "Register address" and "Display buffer address". S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 7 Note When "Epson S5U13A04B00B/B00C Evaluation Board" is selected, the register and display buffer addresses are blanked because the evaluation board uses the PCI interface and the decode addresses are determined by the system BIOS during boot-up. Register Address The physical address of the start of register decode space (in hexadecimal). This field is automatically set according to the Decode Address unless the "User-Defined" decode address is selected. Display Buffer Address The physical address of the start of display buffer decode space (in hexadecimal). This field is automatically set according to the Decode Address unless the "User-Defined" decode address is selected. USB Support The S1D13A04 contains a USB client controller. If this box is checked, chip initialization will configure GPIO[7:4] for use by the USB controller. For further information on the S1D13A04 USB implementation, see the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. The S5U13A04B00C evaluation board implements a Cypress ICD2061A Clock Synthesizer which can be used to generate CLKI and CLKI2. When this box is checked, GPIO[3:1] are reserved for Clock Synthesizer support. Selecting a HR-TFT panel will disable this feature as the HR-TFT requires GPIO[3:0]. Note that this feature is only available when using the S5U13A04B00C. Display Data Byte Swap When this box is checked, the word data from the display buffer is byte swapped. This box should be checked when the display color depth is 16 bpp on a Big Endian platform. When this box is checked, word data sent to/read from the 2D BitBLT memory is byte swapped. This box should be checked when using the 2D BitBLT functions on a Big Endian platform. Clock Chip Support BitBLT Data Byte Swap 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 X37A-B-001-01 Page 8 Epson Research and Development Vancouver Design Center Preferences Tab Color Depth S1D Controller Panel SwivelView Pixel Doubling Display Start Address Display Stride Panel Invert Configuration Description The Preference tab contains settings pertaining to the initial display state. During runtime these settings may be changed. S1D Controller 13A04CFG is designed to support the S1D13A03 and the S1D13A04. When a controller is selected, 13A04CFG determines the maximum panel dimensions based on the video memory (display buffer) size. Some S1D13A04 configurations may not be possible for the S1D13A03 due to memory limitations. These settings allow the Pixel Doubling feature to be configured independently in the horizontal and vertical dimensions. Pixel doubling causes each pixel of display data to be extended to two pixels. This feature can be useful for using existing software on larger panels. When this box is checked, pixel doubling in the horizontal direction is enabled. Note that the S1D13A04 does not support horizontal pixel doubling at a color depth of 1 bpp. Pixel Doubling Horizontal S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 9 Vertical When this box is checked, pixel doubling in the vertical direction is enabled. Note that the S1D13A04 does not support vertical pixel doubling at a color depth of 1 bpp. The S1D13A04 can invert the display data going to the LCD panel. When this box is checked, video data is inverted. Display data is inverted after the Look-Up Table, which means colors are truly inverted. This field allows the user to enter a description for a particular configuration. This field is saved in the HAL information and is displayed when a HAL-based utility is run. Sets the initial color depth on the LCD panel. If there is insufficient display buffer for the selected width and height then a warning is displayed in the diagnostic area. The S1D13A04 SwivelView feature is capable of rotating the image displayed on an LCD panel 90, 180, or 270 in a counter-clockwise direction. This setting determines the initial orientation of the panel. These settings allow fine tuning of the start address and stride. The start address defines the offset into the display buffer (video memory) of the pixel which will be displayed in the top left corner of the panel. Stride defines the number of bytes required to step from the first pixel on one row to the first pixel on the next row (i.e. 160 pixel wide display at 16 bpp requires 320 bytes per horizontal row). This option sets the start address for the main window of the panel. Typically the start address is set to zero. This option sets the stride for the main window of the panel. To set the stride equal to the size of the display, select the "auto" box. To increase the stride, uncheck the "auto" box and enter the desired stride. Note The stride value must be greater than or equal to the number of bytes required by one line of display memory. Panel Invert Configuration Description Color Depth Panel SwivelView Advanced Display Start Address Display Stride 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 X37A-B-001-01 Page 10 Epson Research and Development Vancouver Design Center Clocks Tab PCLK Source PCLK Divide PWMCLK Enable PWMCLK Force High CLKI PWMCLK Source PWMCLK Divide CLKI2 PWMCLK Duty Cycle BCLK Source BCLK Divide MCLK Source MCLK Divide The Clocks tab simplifies the selection of input clock frequencies and the sources of internal clocking signals. For further information regarding clocking and clock sources, refer to the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. The CLKI and CLKI2 frequencies represent clock values the system provides to the S1D13A04. It is the responsibility of the system designer to ensure that the correct clock frequencies are supplied to the S1D13A04. Note Changing clock values may modify or invalidate Panel settings. Confirm all settings on the Panel tab after modifying any clock settings. S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 11 The S1D13A04 may use one or two clock sources. Two clock sources allow greater flexibility in the selection of display type and memory speed. CLKI Timing This setting determines the frequency of CLKI. Set this value by selecting a preset frequency from the drop down list or entering the desired frequency (MHz) in the edit box. This field displays the actual value of the CLKI frequency. If "Enable clock chip support" is selected on the General Tab, then this value may differ slightly from the value entered in the timing control. This setting determines the frequency of CLKI2. Set this value by selecting a preset frequency from the drop down list or entering the desired frequency (MHz) in the edit box. This field displays the actual value of the CLKI2 frequency. If "Enable clock chip support" is selected on the General Tab, then this value may differ slightly from the value entered in the timing control. These settings select the clock source and divisor for the internal pixel clock (PCLK). Selects the PCLK source. Possible sources include CLKI, CLKI2, BCLK or MCLK. Note that BCLK and MCLK may be previously divided from CLKI or CLKI2. Specifies the divide ratio for the clock source. The divide ratio is applied to the PCLK source to derive PCLK. Selecting "Auto" for the divisor allows the configuration program to calculate the best clock divisor. Unless a very specific clocking is being specified, it is best to leave this setting on "Auto". Timing This field shows the actual PCLK used by the configuration process. Actual CLKI2 Timing Actual PCLK Source Divide 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 X37A-B-001-01 Page 12 Epson Research and Development Vancouver Design Center BCLK These settings select the clock source and divisor for the internal bus interface clock (BCLK). The BCLK source is always CLKI. Specifies the divide ratio for the clock source. The divide ratio is applied to the BCLK source to derive BCLK. This field shows the actual BCLK frequency used by the configuration process. These settings select the clock source and input clock divisor for the internal memory clock (MCLK). For the best performance, MCLK should be set as close to the maximum (50 MHz) as possible. The MCLK source is always BCLK. Specifies the divide ratio for the clock source. The divide ratio is applied to the MCLK source to derive MCLK. This divide ratio should be left at 1:1 unless the resultant MCLK is greater that 50MHz. Source Divide Timing MCLK Source Divide Timing This field shows the actual MCLK frequency used by the configuration process. S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 13 PWMCLK These controls configure various PWMCLK settings. The PWMCLK is the internal clock used by the Pulse Width Modulator for output to the panel. When this box is checked, the PWMCLK circuitry is enabled. The signal PWMOUT is forced high when this box is checked. When not checked, PWMOUT will be low if PWM is not enabled or will change state according to the configured values when PWM is enabled. Selects the PWMCLK source. Possible sources include CLKI, CLKI2, MCLK, and PCLK. Specifies the divide ratio for the clock source. The divide ratio is applied to the PWMCLK source to derive PWMCLK. Note After this divide is applied, PWMCLK is further divided by 256 to achieve the final PWMCLK frequency. Enable Force High Source Divide Timing This field shows the actual PWMCLK frequency used by the configuration process. Selects the number of cycles that PWMOUT is high out of 256 clock periods. Duty Cycle 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 X37A-B-001-01 Page 14 Epson Research and Development Vancouver Design Center Panel Tab Panel Color Data Width FPLINE Polarity FPFRAME Polarity Panel Dimensions Panel Type Format 2 Display Total Frame Rate Pixel Clock Predefined Panels HRTC/FPLINE Display Start VRTC/FPFRAME The S1D13A04 supports many panel types. This tab allows configuration of most panel related settings such as dimensions, type and timings. Panel Type Selects between passive (STN), active (TFT), and reflective (HR-TFT) panel types. Some options may change or become unavailable when the STN/TFT/HR-TFT setting is changed. Re-confirm all settings on this tab after the Panel Type is changed. Format 2 Selects color STN panel data format 2. This option only applies to 8-bit color STN panels. See the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx, for description of format 1 / format 2 data formats. Most new panels use the format 2 data format. S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 15 Data Width Selects the panel data width. Panel data width is the number of bits of data transferred to the LCD panel on each clock cycle and shouldn't be confused with color depth which determines the number of displayed colors. When a passive panel type is selected, the available options are 4, 8, and 16 bit. When an active panel type (TFT/HR-TFT) is selected, the available options are 9, 12, and 18 bit. Panel Color Polarity Selects between a monochrome or color panel. Allows selection of the polarity for the FPLINE and FPRAME pulses. Note Selecting the wrong pulse polarity may damage the panel. FPLINE Polarity Selects the polarity of the FPLINE pulse. Refer to the panel specification for the correct polarity of the FPLINE pulse. FPFRAME Polarity Selects the polarity of the FPFRAME pulse. Refer to the panel specification for the correct polarity of the FPFRAME pulse. Panel Dimensions These fields specify the panel width and height. A number of common widths and height are available in the selection boxes. If the width/height of your panel is not listed, enter the actual panel dimensions into the edit field. For passive panels, manually entered pixel widths must be a minimum of 32 pixels and can be increased by multiples of 16. For TFT panels, manually entered pixel widths must be a minimum of 8 pixels and can be increased by multiples of 8. If a value is entered that does not meet these requirements, 13A04CFG rounds up the value to the next allowable width. The changed value is reported in the diagnostics portion of the window. 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 X37A-B-001-01 Page 16 Epson Research and Development Vancouver Design Center Display Total It is recommended that the automatically generated Display Total values be used. However, manual adjustment may be used to improve the quality of the displayed image by fine tuning the horizontal and vertical display totals. The display total equals the display period plus the nondisplay period. Refer to S1D13A04 Hardware Functional Specification, document number X37A-A001-xx, for a complete description of the Display Total settings. Note If the horizontal or vertical display totals are set too small, 13A04CFG will display a yellow warning message in the diagnostics portion of the window. Display Start It is recommended that the automatically generated Display Start values be used. However, manual adjustment may be used to improve the quality of the displayed image by fine tuning the horizontal and vertical display start positions. Refer to S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx, for a complete description of the Display Start settings. Note If the horizontal or vertical display start values are set to values that violate the S1D13A04 Hardware Functional Specification, 13A04CFG will display a yellow warning message in the diagnostics portion of the window. Frame Rate The Frame Rate (in Hz) is calculated and displayed based on the current settings as selected on the various tabs. If the resulting Frame Rate is not acceptable, adjust the settings to change the frame rate. Panel dimensions are fixed therefore frame rate can only be adjusted by changing either the PCLK frequency or display total values. Pixel Clock Select the desired Pixel Clock (in MHz) from the dropdown list. The range of frequencies displayed is dependent on the PCLK source and divide settings as selected on the Clocks tab. S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 17 HRTC/FPLINE (pixels) These settings allow fine tuning of the TFT line pulse parameters. Refer to S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx for a complete description of the FPLINE pulse settings. Specifies the delay (in pixels) from the start of the horizontal non-display period to the leading edge of the FPLINE pulse. Specifies the width (in pixels) of the horizontal sync signal (FPLINE). These settings allow fine tuning of the frame pulse parameters. Refer to S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx, for a complete description of the FPFRAME pulse settings. Specifies the delay (in lines) from the start of the vertical non-display period to the leading edge of the FPFRAME pulse. Specifies the pulse width (in lines) of the vertical sync signal (FPFRAME). 13A04CFG uses a file (panels.def) which contains predefined settings for a number of LCD panels. If the file panels.def is present in the same directory as 13A04cfg.exe, the predefined panels are available in the drop-down list. If a panel is selected from the list, 13A04CFG preconfigures its settings to nominal panel values. Start pos Pulse Width VRTC/FPFRAME (lines) Start pos Pulse width Predefined Panels 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 X37A-B-001-01 Page 18 Epson Research and Development Vancouver Design Center Panel Power Tab Power Panel Support Enable Power Up Time Delay GPIO Selection Power Down Time Delay S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 19 The S5U13A04B00C evaluation board is designed to use a GPIO signal to control the LCD bias power. The following settings configure panel power support. Power Panel Support Enable When this box is checked, the LCD bias power to the panel is controlled by the selected GPIO pin. When this box is unchecked, the LCD bias power must be controlled by the CPU or some other means. This setting selects the GPIO pin used to control the LCD bias power. The default is GPIO0 (GPIO0 is used on the S1D13A04 evaluation board). This setting controls the maximum time delay between when the S1D13A04 control signals are turned on and the LCD panel is powered-on. This setting must be configured according to the specification for the panel being used. This value is used by Epson evaluation software designed for the S5U13A04B00C evaluation board. Power Down Time Delay This setting controls the minimum time delay between when the LCD panel is powered-off and when the S1D13A04 control signals are turned off. This setting must be configured according to the specification for the panel being used. This value is used by Epson evaluation software designed for the S5U13A04B00C evaluation board. GPIO Selection Power Up Time Delay 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 X37A-B-001-01 Page 20 Epson Research and Development Vancouver Design Center Registers Tab The Registers tab allows viewing and editing of the S1D13A04 register values. Scroll up and down the list to view register values which are determined from the configuration settings of the previous tabs. Hovering over a register displays a pop-up help box which describes the functionality of the bits in that register. Register settings may be changed by double-clicking on the register in the listing. Manual changes to the registers are not checked for errors, so caution is warranted when directly editing these values. It is strongly recommended that the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx be referred to before making any manual register settings. Note Manually entered values may be changed by 13A04CFG if further configuration changes are made on other tabs. In this case, the user is notified. S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 21 Direct Tab Program Clock Chip Initialize Registers Initialize Lookup Table Clear Video Memory Write Settings Show Test Pattern Display Test Pattern Shutdown S1D13A04 Initialize S1D13A04 This tab allows the user to directly interact with the S1D13A04 configuration process. The effect of register changes on the displayed image can be observed before writing any configuration files. Fine tuning adjustments may be made to achieve the best possible image on the panel. Using this tab requires that a S5U13A04B00C evaluation board is installed in the computer and a panel is attached. Initialization These settings define which actions will be carried out when the Initialize S1D13A04 button is clicked. The S5U13A04B00C evaluation board design includes a clock chip which can provide the signals for CLKI and CLKI2. Checking this box will include programming the clock chip as part of the S1D13A04 initialization. When this box is checked the S1D13A04 registers will be programmed to their configured values as part of the initialization. Program Clock Chip Initialize Registers 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 X37A-B-001-01 Page 22 Epson Research and Development Vancouver Design Center Initialize Lookup Table When this box is checked the S1D13A04 Lookup Table is programmed as part of the initialization. When this box is checked the S1D13A04 display buffer will be cleared (set to zeros) as part of the initialization. Clicking this button initializes the S1D13A04 according to the options selected. After initializing the S1D13A04, these further options become available. This setting should be used with caution. Checking this box will cause setting changes on any tab to immediately update the associated register(s). Checking this box will update the test pattern in the display buffer after every setting change. This is useful when fine tuning panel settings as the results of the change are immediately visible. Clicking this button causes 13A04CFG to draw a test pattern into display memory. The pattern is based on the configured width, height, rotation and color depth. Clicking this button shuts down the S1D13A04. This feature is necessary should a setting change appear to be damaging or harmful to the attached panel. Clear Video Memory Initialize S1D13A04 Additional Options Write Settings Show Test Pattern Display Test Pattern Shutdown S1D13A04 S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 23 13A04CFG Menus The following sections describe each of the options in the File and Help menus. Open... From the Menu Bar, select "File", then "Open..." to display the Open File Dialog Box. The Open option allows 13A04CFG to read the configuration information from programs based on the HAL library. When 13A04CFG opens a file it scans the file for an identification string, and if found, reads the configuration information. This feature may be used to quickly arrive at a starting point for register configuration. The only requirement is that the file being opened must contain a valid S1D13A04 HAL library information block. 13A04CFG supports a variety of executable file formats. Select the file type(s) 13A04CFG should display in the Files of Type drop-down list and then select the filename from the list and click on the Open button. Note 13A04CFG is designed to work with utilities programmed using a given version of the HAL. If the configuration structure contained in the executable file differs from the version 13A04CFG expects the Open will fail and an error message is displayed. This may happen if the version of 13A04CFG is substantially older, or newer, than the file being opened. 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 X37A-B-001-01 Page 24 Epson Research and Development Vancouver Design Center Save From the Menu Bar, select "File", then "Save" to initiate the save action. The Save menu option allows a fast save of the configuration information to a file that was opened with the Open menu option. Note This option is only available once a file has been opened. Save As... From the Menu Bar, select "File", then "Save As..." to display the Save As Dialog Box. "Save as" is very similar to Save except a dialog box is displayed allowing the user to name the file before saving. Using this technique a tester can configure a number of files differing only in configuration information and name (e.g. BMP60Hz.EXE, BMP72Hz.EXE, BMP75Hz.EXE where only the frame rate changes in each of these files). Note When "Save As" is selected then an exact duplicate of the file as opened by the "Open" option is created containing the new configuration information. S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 25 Configure Multiple After determining the desired configuration, "Configure Multiple" allows the information to be saved into one or more executable files built with the HAL library. From the Menu Bar, select "File", then "Configure Multiple" to display the Configure Multiple Dialog Box.This dialog box is also displayed when a file(s) is dragged onto the 13A04CFG window. The left pane lists files available for configuration; the right pane lists files that have been selected for configuration. Files can be selected by clicking the "Add" or "Add All" buttons, double clicking any file in the left pane, or by dragging the file(s) from Windows Explorer. Selecting "Show all files" displays all files in the selected directory, whereas selecting "Show conf. files only" will display only files that can be configured using 13A04CFG (i.e. .exe, .s9). Checking "Preserve Physical Addresses" instructs 13A04CFG to use the register and display buffer address values the files were previously configured with. Addresses specified in the General Tab are discarded. This is useful when configuring several programs for various hardware platforms at the same time. For example, if configuring PCI, MPC and IDP based programs at the same time for a new panel type, the physical addresses for each are retained. This feature is primarily intended for the test lab where multiple hardware configurations exist and are being tested. 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 X37A-B-001-01 Page 26 Epson Research and Development Vancouver Design Center Export After determining the desired configuration, "Export" permits the user to save the register information as a variety of ASCII text file formats. The following is a list and description of the currently supported output formats: * a C header file for use in writing HAL library based applications. * a C header file which lists each register and the value it should be set to. * a C header file for use in developing Window CE display drivers. * a C header file for use in developing display drivers for other operating systems such as Linux, QNX, and VxWorks WindML. * a comma delimited text file containing an offset, a value, and a description for each S1D13A04 register. * a .html based reference guide to the S1D13A04 registers. After selecting the file format, click the "Export As..." button to display the file dialog box which allows the user to enter a filename before saving. Clicking the "Preview" button uses Notepad or the web browser to display a copy of the file to be saved. When the C Header File for S1D13A04 WinCE Drivers option is selected as the export type, additional options are available and can be selected by clicking on the Options button. The options dialog appears as: Cursor Support selects the type of cursor support enabled in the header file SW Acceleration enables software BitBLT acceleration in the header file HW Acceleration enables hardware BitBLT acceleration in the header file Mode Number selects the mode number for use in the header file S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 27 Enable Tooltips Tooltips provide useful information about many of the items on the configuration tabs. Placing the mouse pointer over nearly any item on any tab generates a popup window containing helpful advice and hints. To enable/disable tooltips check/uncheck the "Tooltips" option form the "Help" menu. Note Tooltips are enabled by default. Tooltip Delay This option sets the length of time the cursor must be left over an item before its associated tooltip is displayed. ERD on the Web This "Help" menu item is actually a hotlink to the Epson Research and Development website. Selecting "Help" then "ERD on the Web" starts the default web browser and points it to the ERD product web site. The latest software, drivers, and documentation for the S1D13A04 is available at this website. Update Common Controls 13A04CFG uses some of the latest common control DLLs. On systems using earlier versions of the common controls, certain controls may not appear correctly. This option updates the Common Controls required for proper operation of 13A04CFG. About 13A04CFG Selecting the "About 13A04CFG" option from the "Help" menu displays the about dialog box for 13A04CFG. The about dialog box contains version information and the copyright notice for 13A04CFG. 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 X37A-B-001-01 Page 28 Epson Research and Development Vancouver Design Center Comments * On any tab particular options may be grayed out if selecting them would violate the operational specification of the S1D13A04 (i.e. Selecting TFT or STN on the Panel tab enables/disables options specific to the panel type). * The file panels.def is a text file containing operational specifications for several supported, and tested, panels. This file can be edited with any text editor. * 13A04CFG allows manually altering register values. The manual changes may violate memory and LCD timings as specified in the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. If this is done, unpredictable results may occur. Epson Research and Development, Inc. does not assume liability for any damage done to the display device as a result of configuration errors. * Yellow diagnostic warnings are designed to draw attention to important errors in the configuration and should be corrected before saving the configuration. * 13A04CFG can be configured by making a copy of the file 13A04cfg.exe and configuring the copy. It is not possible to configure the original while it is running. The newly saved information becomes the default configuration for that copy of 13A04cfg.exe. S1D13A04 X37A-B-001-01 13A04CFG Configuration Program Issue Date: 01/10/19 S1D13A04 LCD/USB Companion Chip 13A04PLAY Diagnostic Utility Document Number: X37A-B-002-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-B-002-01 13A04PLAY Diagnostic Utility Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 3 13A04PLAY 13A04PLAY is a diagnostic utility which allows a user to read/write all the registers and display buffer of the S1D13A04. Commands are received from the standard input device, and messages are sent to the standard output device. On Intel platforms the console provides standard input/output. For most embedded systems the serial device provides these functions. Commands can be entered interactively by a user, or be executed from a script file. Scripting is a powerful feature which allows command sequences to be used repeatedly without re-entry. S1D13A04 Supported Evaluation Platforms 13A04PLAY is available as an executable for PCs running Windows(R) 9x/ME/NT/2000 and as C source code which can be modified and recompiled to allow 13A04PLAY to run on other platforms. 13A04PLAY Diagnostic Utility Issue Date: 01/10/05 S1D13A04 X37A-B-002-01 Page 4 Epson Research and Development Vancouver Design Center Installation PC platform Copy the file 13A04play.exe to a directory in the path (e.g. PATH=C:\S1D13A04). Embedded platform Download the program 13A04play to the system. Usage PC platform At the prompt, type: 13A04play [/?] Where: /? displays copyright and program version information. Embedded platform Execute 13A04play and at the prompt, type the command line argument /?. Where: /? displays copyright and program version information. S1D13A04 X37A-B-002-01 13A04PLAY Diagnostic Utility Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 5 Commands The following commands are intended to be used from within the 13A04PLAY program. However, simple commands can also be executed from the command line (e.g. 13A04play f 0 14000 AB q). Note If the host platform is big endian, reading/writing words and dwords to/from the registers and display buffer may be incorrect. It may be necessary for the user to manually swap the bytes in order to perform the IO correctly. For further information on little/big endian and the S1D13A04 byte/word swapping capabilities, see the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. CLKI freq Sets the frequency of CLKI. Where: freq CLKI2 freq Sets the frequency of CLKI2. Where: freq The desired frequency for CLKI (in MHz). The desired frequency for CLKI2 (in MHz). D[8|16|32] [startaddr [endaddr|len]] Displays a memory dump from the specified display buffer address range. Where: 8|16|32 startaddr endaddr|len The unit size: 8-bit (bytes), 16-bit (words), 32-bit (dwords). If a unit size is not specified, this command uses the unit size from the last Dump command performed. If no previous Dump command has been issued, the unit size defaults to 8-bit. The starting address to read data from. Specifying a period (.) uses the same starting address as the last Dump command performed. Specifying a startaddr of two periods (..) will back the start address by the size of len. Determines how many units to continue dumping the contents of the display buffer. A number without a prefix represents a physical ending address. If an "L" prefix is used, the number that follows represents len, which is the number of bytes/words/dwords to be dumped. Len is based on the unit size. For example, 'L8' when the unit size is 16-bit would cause the Dump command to dump 8 words from the starting address. 13A04PLAY Diagnostic Utility Issue Date: 01/10/05 S1D13A04 X37A-B-002-01 Page 6 Epson Research and Development Vancouver Design Center F[8|16|32] startaddr endaddr|len data1 [data2 data3 ...] Fills a specified address range in the display buffer. Where: 8|16|32 startaddr endaddr|len data The unit size: 8-bit (bytes), 16-bit (words), 32-bit (dwords). If a unit size is not specified, this command uses the unit size from the last Fill command performed. If no previous Fill command has been issued, the unit size defaults to 8-bit. The starting address to begin filling at. Specifying a period (.) uses the same starting address as the last Fill command performed. Determines how many units to fill the display buffer with. A number without a prefix represents a physical ending address. If a "L" prefix is used, the number that follows represents len, or the number of bytes/words/dwords to be filled. Len is based on the unit size. For example, 'L8' when the unit size is 16-bit would cause the Fill command to fill 8 words from the starting address. The value(s) used to fill the display buffer. If multiple values are given, the pattern repeats through memory. Values can be combinations of 'text' or numbers. Numbers are assumed to be hexadecimal values unless otherwise specified with the correct suffix (binary = i, octal = o, decimal = t, hexadecimal = h). For example, 101i = 101 binary. H [lines] Sets the number of lines of data that are displayed at a time. The display is halted after the specified number of lines. Setting the number of lines to 0 disables the halt function and allows the data to continue displaying until all data has been shown. This command is useful when large blocks of the display buffer or the contents of the LUT are being viewed. Where: lines Number of lines that are shown before halting the displayed data (decimal value). I Initializes the S1D13A04 registers with the default register settings as configured by the utility 13A04CFG. To initialize the S1D13A04 with different register values, reconfigure 13A04PLAY using 13A04CFG. For further information on 13A04CFG, see the 13A04CFG User Manual, document number X37A-B-001-xx. Note If the "I" command is used before 13A04PLAY is configured, an error message is displayed and no further action is taken. S1D13A04 X37A-B-002-01 13A04PLAY Diagnostic Utility Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 7 L index [red green blue] Reads/writes the red, green, and blue Look-Up Table (LUT) components. If the red, green, and blue components are not specified, the LUT for the given index is read and the RGB values are displayed. Where: index red green blue Note Index into the LUT (hex). Red component of the LUT (hex). Green component of the LUT (hex). Blue component of the LUT (hex). Only bits 7-2 of each color are used in the LUT. The least significant two bits of the colors are discarded. For example, the command L 0 1 2 3 will set each RGB component of LUT index 0 to 0, as the values 1, 2, an 3 use only the least significant bits. LA Reads and displays all LUT values. M [bpp] Sets the color depth (bpp). If no color depth is provided, information about the current settings are displayed. Where: bpp Note Color depth to be set (1/2/4/8/16 bpp). This command reads and interprets the S1D13A04 control registers. To function correctly the registers must have been initialized using the `I' command. Q Quits the program. R[8|16|32] [addr1 addr2 addr3 ...] Reads the display buffer at the address locations given. Where: 8|16|32 addr The unit size: 8-bit (bytes), 16-bit (words), 32-bit (dwords). If a unit size is not specified, this command uses the unit size from the last Read command performed. If no previous Read command has been issued, the unit size defaults to 8-bit. The address to read data from. Multiple addresses can be given. 13A04PLAY Diagnostic Utility Issue Date: 01/10/05 S1D13A04 X37A-B-002-01 Page 8 Epson Research and Development Vancouver Design Center Run scriptfile This command opens the file scriptfile and executes each line as if it were typed from the command prompt. For more information on scriptfiles, see Section , "Script Files" on page 12. Where: scriptfile The file containing 13A04PLAY commands S[8|16|32] startaddr endaddr|len data1 [data2 data3 data4 ...] Search the display buffer for the given data. Where: 8|16|32 startaddr endaddr|len data The unit size: 8-bit (bytes), 16-bit (words), 32-bit (dwords). If a unit size is not specified, this command uses the unit size from the last Search command performed. If no previous Search command has been issued, the unit size defaults to 8-bit. The starting address to begin the search from. Specifying a period (.) uses the same starting address as the last Search command performed. Determines how many units of the display buffer will be searched through. A number without a prefix represents a physical ending address. If a "L" prefix is used, the number that follows represents len, or the number of bytes/words/dwords to be searched through. Len is based on the unit size. For example, 'L8' when the unit size is 16-bit would cause the Search command to search 8 words from the starting address. The value(s) to search the display buffer for. Values can be combinations of 'text' or numbers. Numbers are assumed to be hexadecimal values unless otherwise specified with the correct suffix (binary = i, octal = o, decimal = t, hexadecimal = h). For example, 101i = 101 binary. Show Shows a test pattern on the display. The test pattern is based on current register settings and may not display correctly if the registers are not configured properly. Use this command to display an image during testing. After adjusting a register value, use the show command to view the effect on the display. S1D13A04 X37A-B-002-01 13A04PLAY Diagnostic Utility Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 9 U index [data] Reads/writes data to the USB register at index. If no data is specified, the command reads and displays the contents from the USB register at index. Where: index data Index into the USB registers (hex). The value to be written to the register. Numbers are assumed to be hexadecimal values unless otherwise specified with the correct suffix (binary = i, octal = o, decimal = t, hexadecimal = h). For example, 101i = 101 binary. UA Reads and displays the contents of all the USB registers. UX index [data] This command automates the writes/reads into the indexed USB registers located at REG[4038h] and REG[403Ah]. Index represents the value that would be written into REG[4038h] if separate operations were done to access the index and data registers. If no data is specified, the command reads and displays the contents of the specified extended USB register. Where: index data Index into USB registers at REG[403Ah] (hex). The value to be written to the indexed data register. Numbers are assumed to be hexadecimal values unless otherwise specified with the correct suffix (binary = i, octal = o, decimal = t, hexadecimal = h). For example, 101i = 101 binary. 13A04PLAY Diagnostic Utility Issue Date: 01/10/05 S1D13A04 X37A-B-002-01 Page 10 Epson Research and Development Vancouver Design Center W[8|16|32] [startaddr [data1 data2 data3 data4 ...]] Writes the given data sequence to the display buffer starting at startaddr location. Where: 8|16|32 startaddr data The unit size: 8-bit (bytes), 16-bit (words), 32-bit (dwords). If a unit size is not specified, this command uses the unit size from the last Write command performed. If no previous Write command has been issued, the unit size defaults to 8-bit. The starting address to write data to. Specifying a period (.) uses the same starting address as the last Write command performed. Values to write to the display buffer. If no data is given, then this function enters MODIFY mode. This mode prompts the user with the address and it's current data. While in this mode, the user can type any of the following. - new values (in hex) - ENTER or SPACE - moves to the next memory location (if data is specified the previous memory location is updated, if no data is specified no change is made) - "-" - moves to the previous memory location - "Q" or "." - exits MODIFY mode X[8|16|32] [index [data]] Reads/writes data to the register at index. If no data is specified, the register is read and the contents are displayed. Where: 8|16|32 index data The unit size: 8-bit (bytes), 16-bit (words), 32-bit (dwords). If a unit size is not specified, this command uses the unit size from the last X command performed. If no previous X command has been issued, the unit size defaults to 8-bit. Index into the registers (hex). The value to be written to the register. Numbers are assumed to be hexadecimal values unless otherwise specified with the correct suffix (binary = i, octal = o, decimal = t, hexadecimal = h). For example, 101i = 101 binary. XA Reads and displays the contents of all the S1D13A04 registers. ? Displays the help screen. The help screen contains a summary of all available commands. S1D13A04 X37A-B-002-01 13A04PLAY Diagnostic Utility Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 11 13A04PLAY Example 1. Configure 13A04PLAY using the utility 13A04CFG. For further information on 13A04CFG, see the 13A04CFG User Manual, document number X37A-B-001-xx. 2. Type 13A04PLAY to start the program. 3. Type ? for help. 4. Type i to initialize the registers. 5. Type xa to display the contents of the registers. 6. Type x 80 to read register 80h. 7. Type x 80 10 to write 10h to register 80h. 8. Type f 0 ffff aa to fill the first 10000h bytes of the display buffer with AAh. 9. Type d 0 ff to read the first 100h bytes of the display buffer. 10. Type show to display a test pattern. 11. Type m to display current mode information. 12. Type m 2 to set the color depth to 2 bpp. 13. Type show to display a test pattern. 14. Type q to exit the program. 13A04PLAY Diagnostic Utility Issue Date: 01/10/05 S1D13A04 X37A-B-002-01 Page 12 Epson Research and Development Vancouver Design Center Script Files 13A04PLAY can be controlled by a script file. This is useful when: * there is no display to monitor command keystroke accuracy. * various registers must be quickly changed to view results. A script file is an ASCII text file with one 13A04PLAY command per line. Script files can be executed from within 13A04PLAY using the Run command (e.g. = run dumpregs.scr). Alternately, the script file can be executed from the OS command prompt. On a PC platform, a typical script command line might be: 13A04PLAY run dumpregs.scr > results This causes the file dumpregs.scr to be interpreted as commands by 13A04PLAY and the results to be redirected to the file results. Example 1: Create a script file that reads all registers. ; This file initializes the S1D13A04 and reads the registers. ; Note: after a semicolon (;), all characters on a line are ignored. ; Initialize the S1D13A04 i ; Read all registers xa S1D13A04 X37A-B-002-01 13A04PLAY Diagnostic Utility Issue Date: 01/10/05 S1D13A04 LCD/USB Companion Chip 13A04BMP Demonstration Program Document Number: X37A-B-003-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-B-003-01 13A04BMP Demonstration Program Issue Date: 01/10/04 Epson Research and Development Vancouver Design Center Page 3 13A04BMP 13A04BMP is a demonstration utility used to show the S1D13A04 display capabilities by rendering bitmap images on the display device. The program displays a bitmap stored in Windows BMP file format and then exits. 13A04BMP supports SviwelViewTM (90, 180, and 270 hardware rotation of the display image). 13A04BMP is designed to operate on a personal computer (PC) within a 32-bit environment only (Windows(R) 9x/NT/ME/2000). Other embedded platforms are not supported due to the possible lack of system memory or structured file system. The 13A04BMP demonstration utility must be configured to work with your hardware configuration. The program 13A04CFG can be used to configure 13A04BMP. For further information on 13A04CFG, refer to the 13A04CFG Users Manual, document number X37A-B-001-xx. S1D13A04 Supported Evaluation Platforms 13A04BMP supports the following S1D13A04 evaluation platforms: * PC with an Intel 80x86 processor running Windows 9x/NT/ME/2000. Note The 13A04BMP source code may be modified by the OEM to support other evaluation platforms. Installation Copy the file 13A04bmp.exe to a directory in the path (e.g. PATH=C:\S1D13A04). 13A04BMP Demonstration Program Issue Date: 01/10/04 S1D13A04 X37A-B-003-01 Page 4 Epson Research and Development Vancouver Design Center Usage At the prompt, type: 13A04bmp bmpfile [/?] Where: bmpfile /? Note Specifies filename of the windows format bmp image to be displayed. Displays the help message. 13A04BMP displays the bmpfile image and returns to the prompt. 13A04BMP Examples To display a .bmp image in the main window on an LCD, type the following: 13A04bmp bmpfile.bmp Note To display a bmpfile using SwivelView, configure 13A04bmp.exe for the selected SwivelView mode using the configuration program 13A04CFG. For further information on 13A04CFG, see the 13A04CFG User Manual, document number X37A-B-001-xx. Comments * 13A04BMP displays only Windows BMP format images. * A 24-bit true color bitmap is displayed at a color depth of 16 bit-per-pixel. * Only the green component of the image is seen on a monochrome panel. * 13A04BMP does not perform any image translations. The image to display must be the desired dimensions and color depth. S1D13A04 X37A-B-003-01 13A04BMP Demonstration Program Issue Date: 01/10/04 S1D13A04 LCD/USB Companion Chip Wind River WindML v2.0 Display Drivers Document Number: X37A-E-002-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All other trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-E-002-01 Wind River WindML v2.0 Display Drivers Issue Date: 01/09/28 Epson Research and Development Vancouver Design Center Page 3 Wind River WindML v2.0 DISPLAY DRIVERS The Wind River WindML v2.0 display drivers for the S1D13A04 LCD/USB Companion Chip are intended as "reference" source code for OEMs developing for Wind River's WindML v2.0. The driver package provides support for both 8 and 16 bit-per-pixel color depths. The source code is written for portability and contains functionality for most features of the S1D13A04. Source code modification is required to produces a smaller, more efficient driver for mass production. The WindML display drivers are designed around a common configuration include file called mode0.h which is generated by the configuration utility 13A04CFG. This design allows for easy customization of display type, clocks, decode addresses, rotation, etc. by OEMs. For further information on 13A04CFG, see the 13A04CFG Configuration Program User Manual, document number X37A-B-001-xx. Note The WindML display drivers are provided as "reference" source code only. They are intended to provide a basis for OEMs to develop their own drivers for WindML v2.0. These drivers are not backwards compatible with UGL v1.2. For information on UGL v1.2 display drivers, contact us via email at erdvdcsw_info@erd.epson.com. This document and the source code for the WindML display drivers is updated as appropriate. Please check the Epson Research and Development website at www.erd.epson.com for the latest revisions before beginning any development. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. Wind River WindML v2.0 Display Drivers Issue Date: 01/09/28 S1D13A04 X37A-E-002-01 Page 4 Epson Research and Development Vancouver Design Center Building a WindML v2.0 Display Driver The following instructions produce a bootable disk that automatically starts the UGL demo program. These instructions assume that Wind River's Tornado platform is already installed. Note For the example steps where the drive letter is given as "x:". Substitute "x" with the drive letter that your development environment is on. 1. Create a working directory and unzip the WindML display driver into it. From a command prompt or GUI interface create a new directory (e.g. x:\13A04). Unzip the file 13A04windml.zip to the newly created working directory. The files will be unzipped to the directories "x:\13A04\8bpp" and "x:\13A04\16bpp". 2. Configure for the target execution model. This example build creates a VxWorks image that fits onto and boots from a single floppy diskette. In order for the VxWorks image to fit on the disk certain modifications are required. Replace the file "x:\Tornado\target\config\pcPentium\config.h" with the file "x:\13A04\8bpp\File\config.h" (or "x:\13A04\16bpp\File\config.h"). The new config.h file removes networking components and configures the build image for booting from a floppy disk. Note Rather than simply replacing the original config.h file, rename it so the file can be kept for reference purposes. 3. Build a boot ROM image. From the Tornado tool bar, select Build -> Build Boot ROM. Select "pcPentium" as the BSP and "bootrom_uncmp" as the image. 4. Create a bootable disk (in drive A:). From a command prompt change to the directory "x:\Tornado\host\x86-win32\bin" and run the batch file torvars.bat. Next, change to the directory "x:\Tornado\target\config\pcPentium" and type: mkboot a: bootrom_uncmp S1D13A04 X37A-E-002-01 Wind River WindML v2.0 Display Drivers Issue Date: 01/09/28 Epson Research and Development Vancouver Design Center Page 5 5. If necessary, generate a new mode0.h configuration file. The file mode0.h contains the register values required to set the screen resolution, color depth (bpp), display type, rotation, etc. The mode0.h file included with the drivers, may not contain applicable values and must be regenerated. The configuration program 13A04CFG can be used to build a new mode0.h file. If building for 8 bpp, place the new mode0.h file in the directory "x:\13A04\8bpp\File". If building for 16 bpp, place the new mode0.h file in "x:\13A04\16bpp\File". Note Mode0.h should be created using the configuration utility 13A04CFG. For more information on 13A04CFG, see the 13A04CFG Configuration Program User Manual, document number X37A-B-001-xx available at www.erd.epson.com. 6. Build the WindML v2.0 library. From a command prompt change to the directory "x:\Tornado\host\x86-win32\bin" and run the batch file torvars.bat. Next, change to the directory "x:\Tornado\target\src\ugl" and type the command: make CPU=PENTIUM ugl 7. Open the S1D13A04 workspace. From the Tornado tool bar, select File->Open Workspace...->Existing->Browse... and select the file "x:\13A04\8bpp\13A03.wsp" (or "x:\13A04\16bpp\13A04.wsp"). 8. Add support for single line comments. The WindML v2.0 display driver source code uses single line comment notation, "//", rather than the ANSI conventional comments, "/*...*/". To add support for single line comments follow these steps: a. b. In the Tornado "Workspace Views" window, click on the "Builds" tab. Expand the "8bpp Builds" (or "16bpp Builds") view by clicking on the "+" next to it. The expanded view will contain the item "default". Right-click on "default" and select "Properties...". A "Properties:" window will appear. Select the "C/C++ compiler" tab to display the command switches used in the build. Remove the "-ansi" switch from the line that contains "-g -mpentium -ansi -nostdinc -DRW_MULTI_THREAD". (Refer to GNU ToolKit user's guide for details) c. Wind River WindML v2.0 Display Drivers Issue Date: 01/09/28 S1D13A04 X37A-E-002-01 Page 6 Epson Research and Development Vancouver Design Center 9. Compile the VxWorks image. Select the "Builds" tab in the Tornado "Workspace Views" window. Right-click on "8bpp files" (or "16bpp files") and select "Dependencies...". Click on "OK" to regenerate project file dependencies for "All Project files". Right-click on "8bpp files" (or "16bpp files") and select "ReBuild All(vxWorks)" to build VxWorks. 10. Copy the VxWorks file to the diskette. From a command prompt or through the Windows interface, copy the file "x:\13A04\8bpp\default\vxWorks" (or "x:\13A04\16bpp\default\vxWorks") to the bootable disk created in step 4. 11. Start the VxWorks demo. Boot the target PC with the VxWorks bootable diskette to run the UGL demo program automatically. S1D13A04 X37A-E-002-01 Wind River WindML v2.0 Display Drivers Issue Date: 01/09/28 S1D13A04 LCD/USB Companion Chip Linux Console Driver Document Number: X37A-E-004-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-E-004-01 Linux Console Driver Issue Date: 01/09/28 Epson Research and Development Vancouver Design Center Page 3 Linux Console Driver The Linux console driver for the S1D13A04 LCD/USB Companion Chip is intended as "reference" source code for OEMs developing for Linux, and supports 4, 8, and 16 bit-perpixel color depths. The source code is written for portability and contains functionality for most features of the S1D13A04. Source code modification is required to provide a smaller driver for mass production. A Graphical User Interface (GUI) such as Gnome can obtain the frame buffer address from this driver allowing the Linux GUI the ability to update the display. The console driver is designed around a common configuration include file called S1D13A04.h, which is generated by the configuration utility 13A04CFG. This design allows for easy customization of display type, clocks, decode addresses, rotation, etc. by OEMs. For further information on 13A04CFG, see the 13A04CFG Configuration Program User Manual, document number X37A-B-001-xx. Note The Linux console driver is provided as "reference" source code only. The driver is intended to provide a basis for OEMs to develop their own drivers for Linux. This document and the source code for the Linux console drivers are updated as appropriate. Please check the Epson Research and Development website at www.erd.epson.com for the latest revisions or before beginning any development. We appreciate your comments on our documentation. Please contact us via e-mail at documentation@erd.epson.com. Linux Console Driver Issue Date: 01/09/28 S1D13A04 X37A-E-004-01 Page 4 Epson Research and Development Vancouver Design Center Building the Console Driver for Linux Kernel 2.2.x Follow the steps below to construct a copy of the Linux operating system using the S1D13A04 as the console display device. These instructions assume that the GNU development environment is installed and the user is familiar with GNU and the Linux operating system. 1. Acquire the Linux kernel source code. You can obtain the Linux kernel source code from your Linux supplier or download the source from: ftp://ftp.kernel.org. The S1D13A04 reference driver requires Linux kernel 2.2.x. The example S1D13A04 reference driver available on www.erd.epson.com was built using Red Hat Linux 6.1, kernel version 2.2.17. For information on building the kernel refer to the readme file at: ftp://ftp.linuxberg.com/pub/linux/kernel/README Note Before continuing with modifications for the S1D13A04, you should ensure that you can build and start the Linux operating system. 2. Unzip the console driver files. Using a zip file utility, unzip the S1D13A04 archive to a temporary directory. (e.g. /tmp) When completed the following files should be located in the temporary directory. s1d13xxxfb.c S1D13A04.h Config.in fbmem.c fbcon-cfb4.c, and Makefile 3. Copy the console driver files to the build directory. Copy the following files to the directory /usr/src/linux/drivers/video. /tmp/s1d13xxxfb.c and /tmp/S1D13A04.h Copy the remaining source files into the directory /usr/src/linux/drivers/video replacing the files of the same name. /tmp/Config.in /tmp/fbmem.c /tmp/fbcon-cfb4.c, and /tmp/Makefile If your kernel version is not 2.2.17, or you want to retain greater control of the build process, use a text editor to cut and paste the sections dealing with the Epson driver in the corresponding files of the same names. S1D13A04 X37A-E-004-01 Linux Console Driver Issue Date: 01/09/28 Epson Research and Development Vancouver Design Center Page 5 4. Modify S1D13A04.h The file S1D13A04.h contains the register values required to set the screen resolution, color depth (bpp), display type, active display (LCD), display rotation, etc. Before building the console driver, refer to the descriptions in the file S1D13A04.h for the default settings of the console driver. If the default does not match the configuration you are building for then S1D13A04.h must be regenerated with the correct information. Use the program 13A04CFG to generate the required header file. For information on how to use 13A04CFG, refer to the 13A04CFG Configuration Program User Manual, document number X37A-B-001-xx, available at www.erd.epson.com After selecting the desired configuration, choose "File->Export" and select the "C Header File for S1D13A04 Generic Drivers" option. Save the new configuration as S1D13A04.h in the /usr/src/linux/drivers/video, replacing the original configuration file. 5. Configure the video options. From the command prompt in the directory /usr/src/linux run the command: make menuconfig This command will start a text based interface which allows the selection of build time parameters. From the text interface under "Console drivers" options, select: "Support for frame buffer devices" "Epson LCD/CRT controllers support" "S1D13A04 support" "Advanced low level driver options" "xBpp packed pixels support" * * where x is the color depth being compile for. If you are using the Epson S5U13A04B00C evaluation board then you must also select: "Epson PCI Bridge adapter support" Once you have configured the kernel options, save and exit the configuration utility. 6. Compile and install the kernel. Build the kernel with the following sequence of commands. make dep make clean make bzImage /sbin/lilo (if running lilo) Linux Console Driver Issue Date: 01/09/28 S1D13A04 X37A-E-004-01 Page 6 Epson Research and Development Vancouver Design Center 7. Boot to the Linux operating system. If you are using lilo (Linux Loader), modify the lilo configuration file as discussed in the kernel build README file. If there were no errors during the build, from the command prompt run: lilo and reboot your system. Note In order to use the S1D13A04 console driver with X server, you need to configure the X server to use the FBDEV device. The information on the necessary files and instructions for this process is available on the Internet at www.xfree86.org S1D13A04 X37A-E-004-01 Linux Console Driver Issue Date: 01/09/28 Epson Research and Development Vancouver Design Center Page 7 Building the Console Driver for Linux Kernel 2.4.x Follow the steps below to construct a copy of the Linux operating system using the S1D13A04 as the console display device. These instructions assume that the GNU development environment is installed and the user is familiar with GNU and the Linux operating system. 1. Acquire the Linux kernel source code. You can obtain the Linux kernel source code from your Linux supplier or download the source from: ftp://ftp.kernel.org. The S1D13A04 reference driver requires Linux kernel 2.4.x or greater. The example S1D13A04 reference driver available on www.erd.epson.com was built using Red Hat Linux 6.1, kernel version 2.4.5. For information on building the kernel refer to the readme file at: ftp://ftp.linuxberg.com/pub/linux/kernel/README Note Before continuing with modifications for the S1D13A04, you should ensure that you can build and start the Linux operating system. 2. Unzip the console driver files. Using a zip file utility, unzip the S1D13A04 archive to a temporary directory. (e.g. /tmp) When completed the files: Config.in fbmem.c fbcon-cfb4.c Makefile should be located in the temporary directory (/tmp), and the files: Makefile s1d13xxxfb.c S1D13A04.h should be located in a sub-directory called epson within the temporary directory (/tmp/epson). Linux Console Driver Issue Date: 01/09/28 S1D13A04 X37A-E-004-01 Page 8 Epson Research and Development Vancouver Design Center 3. Copy the console driver files to the build directory. Make the directory /usr/src/linux/drivers/video/epson. Copy the files /tmp/epson/s1d13xxxfb.c /tmp/epson/S1D13A04.h /tmp/epson/Makefile to the directory /usr/src/linux/drivers/video/epson. Copy the remaining source files /tmp/Config.in /tmp/fbmem.c /tmp/fbcon-cfb4.c /tmp/Makefile into the directory /usr/src/linux/drivers/video replacing the files of the same name. If your kernel version is not 2.4.5 or you want to retain greater control of the build process then use a text editor and cut and paste the sections dealing with the Epson driver in the corresponding files of the same names. 4. Modify S1D13A04.h The file S1D13A04.h contains the register values required to set the screen resolution, color depth (bpp), display type, active display (LCD/CRT), display rotation, etc. Before building the console driver, refer to the descriptions in the file S1D13A04.h for the default settings of the console driver. If the default does not match the configuration you are building for then S1D13A04.h will have to be regenerated with the correct information. Use the program 13A04CFG to generate the required header file. For information on how to use 13A04CFG, refer to the 13A04CFG Configuration Program User Manual, document number X37A-B-001-xx, available at www.erd.epson.com After selecting the desired configuration, choose "File->Export" and select the "C Header File for S1D13A04 Generic Drivers" option. Save the new configuration as S1D13A04.h in the /usr/src/linux/drivers/video, replacing the original configuration file. S1D13A04 X37A-E-004-01 Linux Console Driver Issue Date: 01/09/28 Epson Research and Development Vancouver Design Center Page 9 5. Configure the video options. From the command prompt in the directory /usr/src/linux run the command: make menuconfig This command will start a text based interface which allows the selection of build time parameters. From the options presented select: "Code maturity level" options "Prompt for development and/or incomplete drivers" "Console drivers" options "Frame-buffer support" "Support for frame buffer devices (EXPERIMENTAL)" "EPSON LCD/CRT/TV controller support" "EPSON S1D13A04 Support" "Advanced low-level driver options" "xbpp packed pixels support" * * where x is the color depth being compiled for. If you are using the Epson S5U13A04B00C evaluation board then you must also select: "Epson PCI Bridge adapter support" Once you have configured the kernel options, save and exit the configuration utility. 6. Compile and install the kernel Build the kernel with the following sequence of commands: make dep make clean make bzImage /sbin/lilo (if running lilo) 7. Boot to the Linux operating system If you are using lilo (Linux Loader), modify the lilo configuration file as discussed in the kernel build README file. If there were no errors during the build, from the command prompt run: lilo and reboot your system. Note In order to use the S1D13A04 console driver with X server, you need to configure the X server to use the FBDEV device. A good place to look for the necessary files and instructions on this process is on the Internet at www.xfree86.org Linux Console Driver Issue Date: 01/09/28 S1D13A04 X37A-E-004-01 Page 10 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-E-004-01 Linux Console Driver Issue Date: 01/09/28 S1D13A04 LCD/USB Companion Chip QNX Photon v2.0 Display Driver Document Number: X37A-E-005-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All other trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-E-005-01 QNX Photon v2.0 Display Driver Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 3 QNX Photon v2.0 Display Driver The Photon v2.0 display driver for the S1D13A04 LCD/USB Companion Chip is intended as "reference" source code for OEMs developing for QNX platforms. The driver package provides support for 8 and 16 bit-per-pixel color depths. The source code is written for portability and contains functionality for most features of the S1D13A04. Source code modification is required to provide a smaller driver for mass production. The current revision of the driver is designed for use with either QNX RTP or QNX4 from the latest product CD (Dec. 99). The Photon v2.0 display driver is designed around a common configuration include file called S1D13A04.h, which is generated by the configuration utility 13A04CFG. This design allows for easy customization of display type, clocks, decode addresses, rotation, etc. by OEMs. For further information on 13A04CFG, see the 13A04CFG Configuration Program User Manual, document number X37A-B-001-xx. Note The QNX display drivers are provided as "reference" source code only. They are intended to provide a basis for OEMs to develop their own drivers for QNX Photon v2.0. This document and the source code for the QNX display drivers are updated as appropriate. Please check the Epson Research and Development website at www.erd.epson.com for the latest revisions before beginning any development. We appreciate your comments on our documentation. Please contact us via e-mail at documentation@erd.epson.com. QNX Photon v2.0 Display Driver Issue Date: 01/10/19 S1D13A04 X37A-E-005-01 Page 4 Epson Research and Development Vancouver Design Center Building the Photon v2.0 Display Driver The following steps build the Photon v2.0 display driver and integrate it into the QNX operating system. These instructions assume the QNX developer environment is correctly installed and the developer is familiar with building for the QNX operating system. Unpack the Graphics Driver Development Kit Archive 1. Install the QNX ddk package using the Package Manager utility. For information about the Drivers Development Kit contact QNX directly. 2. Once the ddk package is installed, copy the directory tree /usr/scr/gddk_v1.0 into the Project directory. 3. Change directory to Project/gddk_1.0/devg. 4. Unpack the display driver files using the commands: #gunzip S1D13A04.tar.gz #tar -xvf S1D13A04.tar This unpacks the files into the directory Project/gddk_1.0/devg/S1D13A04. Configure the Driver The files S1D13A04_16.h and S1D13A04_8.h contain register values required to set the screen resolution, color depth (bpp), display type, rotation, etc. The S1D13A04.h file included with the drivers may not contain applicable values and must be regenerated. The configuration program 13A04CFG can be used to build new S1D13A04_16.h and S1D13A04_8.h files. Note S1D13A04.h should be created using the configuration utility 13A04CFG. For more information on 13A04CFG, see the 13A04CFG Configuration Program User Manual, document number X37A-B-001-xx available at www.erd.epson.com. Build the Driver The first time the driver is built, the following command ensures that all drivers and required libraries are built. At the root of the Project source tree, type make. Note To build drivers for X86 NTO type `OSLIST=nto CPULIST=x86 make'. Further builds do not require all libraries to be re-built. To build only the S1D13A04 display driver, change to the directory gddk_1.0/devg/S1D13A04 and type make. S1D13A04 X37A-E-005-01 QNX Photon v2.0 Display Driver Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 5 Installing the Driver The build step produces two library images: * lib/disputil/nto/x86/libdisputil.so * lib/disputil/nto/x86/libffb.so For the loader to locate them, the files need to be renamed and copied to the lib directory. 1. Rename libdisputil.so to libdisputil.so.1 and libffb.so to libffb.so.1. 2. Copy the files new files libdisputil.so.1 and libffb.so.1 to the directory /usr/lib. 3. Copy the file devg-S1D13A04.so to the /lib/dll directory. Note To locate the file devg-S1D13A04.so, watch the output of the `true' command during the makefile build. Modify the trap file graphics-modes in the /etc/system/config directory by inserting the following lines at the top of the file. io-graphics -dldevg-S1D13A04.so -gWxHxC -I0 -d0x0,0x0;#640,480,8 Epson io-graphics -dldevg-S1D13A04.so -gWxHxC -I0 -d0x0,0x0;#640,480,16 Epson Where: W is the configured width of the display H is the configured height of the display C is the color depth in bpp (either 8 or 16) QNX Photon v2.0 Display Driver Issue Date: 01/10/19 S1D13A04 X37A-E-005-01 Page 6 Epson Research and Development Vancouver Design Center Run the Driver Note For the remaining steps the S5U13A04B00C evaluation board must be installed on the test platform. It is recommended that the driver be verified before starting QNX with the S1D13A04 as the primary display. To verify the driver, type the following command at the root of the Project source tree (gddk_1.0 directory). util/bench/nto/x86/o/devg-bench -dldevg/S1D13A04/nto/x86/dll/devg-S1D13A04.so -mW,H,C,F -d0x0,0x0 Where: W is the configured width of the display H is the configured height of the display C is the color depth in bpp (either 8 or 16) F is the configured frame rate This command starts the bench utility which will initialize the driver as the secondary display and exercise the drivers main functions. If the display appears satisfactory, restart QNX Photon and the restart will result in the S1D13A04 display driver becoming the primary display device. Comments * To restore the display driver to the default, comment out changes made to the trap file crt.$NODE. S1D13A04 X37A-E-005-01 QNX Photon v2.0 Display Driver Issue Date: 01/10/19 S1D13A04 LCD/USB Companion Chip Windows(R) CE 3.x Display Driver Document Number: X37A-E-006-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-E-006-01 Windows(R) CE 3.x Display Driver Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 3 WINDOWS(R) CE 3.0 DISPLAY DRIVER Windows CE v3.0 display driver for the S1D13A04 LCD/USB Companion Chip is intended as "reference" source code for OEMs developing for the Microsoft Window CE platform. The driver supports 4, 8 and 16 bit-per-pixel color depths in landscape mode (no rotation), and 8 and 16 bit-per-pixel color depths in SwivelViewTM 90 degree, 180 degree and 270 degree modes. The source code is written for portability and contains functionality for most features of the S1D13A04. Source code modification is required to provide a smaller driver for mass production. The Windows CE v3.0 display driver is designed around a common configuration include file called mode0.h, which is generated by the configuration utility 13A04CFG. This design allows for easy customization of display type, clocks, decode addresses, rotation, etc. by OEMs. For further information on 13A04CFG, see the 13A04CFG Configuration Program User Manual, document number X37A-B-001-xx. Note The Windows CE display driver is provided as "reference" source code only. They are intended to provide a basis for OEMs to develop their own drivers for Microsoft Windows CE v3.0. This document and the source code for the Windows CE v3.0 driver is updated as appropriate. Before beginning any development, please check the Epson Research and Development Website at www.erd.epson.com for the latest revisions. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. Windows(R) CE 3.x Display Driver Issue Date: 01/10/19 S1D13A04 X37A-E-006-01 Page 4 Epson Research and Development Vancouver Design Center Example Driver Builds The following section describes how to build the Windows CE display driver for Windows CE Platform Builder 3.00 using the GUI interface. Build for CEPC (X86) on Windows CE Platform Builder 3.00 using the GUI Interface 1. Install Microsoft Windows 2000 Professional, or Windows NT Workstation version 4.0 with Service Pack 5 or later. 2. Install Platform Builder 3.00. 3. Start Platform Builder by double-clicking on the Microsoft Windows CE Platform Builder icon. 4. Create a new project. a. Select File | New. b. In the dialog box, select the Platforms tab. c. In the platforms dialog box, select "WCE Platform", set a location for the project (such as x:\myproject), set the platform name (such as myplatform), and set the processor to "Win32 (WCE x86)". d. Click the OK button. e. In the dialog box "WCE Platform - Step 1 of 2", select CEPC. f. Click the Next button. g. In the dialog box "WCE Platform - Step 2 of 2", select Maximum OS (Maxall). h. Click the Finish button. i. In the dialog box "New Platform Information", click the OK button. 5. Set the active configuration to "Win32 (WCE x86) Release". a. From the Build menu, select "Set Active Configuration". b. Select "MYPLATFORM - Win32 (WCE x86) Release". c. Click the OK button. S1D13A04 X37A-E-006-01 Windows(R) CE 3.x Display Driver Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 5 6. Add the environment variable DDI_S1D13A04. a. From the Platform menu, select "Settings". b. Select the "Environment" tab. c. In the Variable box, type "DDI_S1D13A04". d. In the Value box, type "1". e. Click the Set button. f. Click the OK button. 7. Create a new directory S1D13A04, under x:\wince300\platform\cepc\drivers\display, and copy the S1D13A04 driver source code into this new directory. 8. Add the S1D13A04 driver component. a. From the Platform menu, select "Insert | User Component". b. Set "Files of type:" to "All Files (*.*)". c. Select the file x:\wince300\platform\cepc\drivers\display\S1D13A04\sources. d. Click the OK button. e. In the "User Component Target File" dialog box, select browse and then select the path and the file name of "sources" as in step c. f. Click the OK button. 9. Delete the component "ddi_flat". a. In the Platform window, select the ComponentView tab. b. Show the tree for MYPLATFORM components by clicking on the `+' sign at the root of the tree. c. Right-click on the ddi_flat component. d. Select "Delete". e. From the File menu, select "Save Workspace". Windows(R) CE 3.x Display Driver Issue Date: 01/10/19 S1D13A04 X37A-E-006-01 Page 6 Epson Research and Development Vancouver Design Center 10. From the Platform window, click the ParameterView Tab. Show the tree for MYPLATFORM Parameters by clicking the `+' sign at the root of the tree. Expand the the WINCE300 tree and then click on "Hardware Specific Files" and then double click "PLATFORM.BIB". Edit the file the PLATFORM.BIB file and make the following two changes: a. Insert the following text after the line "IF ODO_NODISPLAY !": IF CEPC_DDI_S1D13A04 ddi.dll ENDIF $(_FLATRELEASEDIR)\S1D13A04.dll NK SH b. Find the section shown below, and insert the lines as marked: IF CEPC_DDI_FLAT ! IF DDI_S1D13A04! IF CEPC_DDI_S3VIRGE ! IF CEPC_DDI_CT655X ! IF CEPC_DDI_VGA8BPP ! IF CEPC_DDI_S3TRIO64 ! IF CEPC_DDI_ATI ! ddi.dll ENDIF ENDIF ENDIF ENDIF ENDIF ENDIF ENDIF ;Insert this line $(_FLATRELEASEDIR)\ddi_flat.dll NK SH ;Insert this line S1D13A04 X37A-E-006-01 Windows(R) CE 3.x Display Driver Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 7 11. Modify MODE0.H. The file MODE0.H (located in x:\wince300\platform\cepc\drivers\display\S1D13A04) contains the register values required to set the screen resolution, color depth (bpp), display type, display rotation, etc. Before building the display driver, refer to the descriptions in the file MODE0.H for the default settings of the console driver. If the default does not match the configuration you are building for then MODE0.H will have to be regenerated with the correct information. Use the program 13A04CFG to generate the header file. For information on how to use 13A04CFG, refer to the 13A04CFG Configuration Program User Manual, document number X37A-B-001-xx, available at www.erd.epson.com After selecting the desired configuration, choose "File->Export" and select the "C Header File for S1D13A04 WinCE Driver" option. Save the new configuration as MODE0.H in the \wince300\platform\cepc\drivers\display, replacing the original configuration file. 12. From the Platform window, click the ParameterView Tab. Show the tree for MYPLATFORM Parameters by clicking the `+' sign at the root of the tree. Expand the the WINCE300 tree and click on "Hardware Specific Files", then double click "PLATFORM.REG". Edit the file PLATFORM.REG to match the screen resolution, color depth, and rotation information in MODE0.H. For example, the display driver section of PLATFORM.REG should be as follows when using a 320x240 LCD panel with a color depth of 8 bpp and a SwivelView mode of 0 (landscape): ; Default for EPSON Display Driver ; 320x240 at 8 bits/pixel, LCD display, no rotation ; Useful Hex Values ; 640=0x280 480=0x1E0 320=140 240=0xF0 [HKEY_LOCAL_MACHINE\Drivers\Display\S1D13A04] "Width"=dword:140 "Height"=dword:F0 "Bpp"=dword:8 "Rotation"=dword:0 13. From the Build menu, select "Rebuild Platform" to generate a Windows CE image file (NK.BIN) in the project directory x:\myproject\myplatform\reldir\x86_release\nk.bin. Windows(R) CE 3.x Display Driver Issue Date: 01/10/19 S1D13A04 X37A-E-006-01 Page 8 Epson Research and Development Vancouver Design Center Installation for CEPC Environment Once the NK.BIN file is built, the CEPC environment can be started by booting either from a floppy or hard drive configured with a Windows 9x operating system. The two methods are described below. 1. To start CEPC from a floppy drive: a. Create a bootable floppy disk. b. Copy HIMEM.SYS to the floppy disk and edit CONFIG.SYS on the floppy disk to contain only the following line: device=a:\himem.sys c. Edit AUTOEXEC.BAT on the floppy disk to contain the following lines: loadcepc /B:38400 /C:1 c:\nk.bin d. Search for loadcepc.exe in the Windows CE directories and copy loadcepc.exe to the bootable floppy disk. e. Copy NK.BIN to c:\. f. Boot the system from the bootable floppy disk. 2. To start CEPC from a hard drive: a. Search for loadcepc.exe in the Windows CE directories and copy loadcepc.exe to C:\. b. Edit CONFIG.SYS on the hard drive to contain only the following line: device=c:\himem.sys c. Edit AUTOEXEC.BAT on the hard drive to contain the following lines: loadcepc /B:38400 /C:1 c:\nk.bin d. Copy NK.BIN to c:\. e. Boot the system. S1D13A04 X37A-E-006-01 Windows(R) CE 3.x Display Driver Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 9 Configuration There are several issues to consider when configuring the display driver. The issues cover debugging support, register initialization values and memory allocation. Each of these issues is discussed in the following sections. Compile Switches There are several switches, specific to the S1D13A04 display driver, which affect the display driver. The switches are added or removed from the compile switches in the file SOURCES. WINCEVER This option is automatically set to the numerical version of WinCE for version 2.12 or later. If the environment variable, _WINCEOSVER is not defined, then WINCEVER will default to 2.11. The S1D13A04 display driver may test against this option to support different WinCE version-specific features. EnablePreferVmem This option enables the use of off-screen video memory. When this option is enabled, WinCE can optimize some BLT operations by using off-screen video memory to store images. You may need to disable this option if your off-screen video memory is limited. ENABLE_CLOCK_CHIP This option is used to enable support for the ICD2061A clock generator. This clock chip is used on the S5U13A04B00C evaluation board. The S1D13A04 display drivers can program the clock chip to support the frequencies required in the MODE tables. If you are not using the S5U13A04B00C evaluation board, you should disable this option. EpsonMessages This debugging option enables the display of EPSON-specific debug messages. These debug message are sent to the serial debugging port. This option should be disabled unless you are debugging the display driver, as they will significantly impact the performance of the display driver. DEBUG_MONITOR This option enables the use of the debug monitor. The debug monitor can be invoked when the display driver is first loaded and can be used to view registers, and perform a few debugging tasks. The debug monitor is still under development and is UNTESTED. Windows(R) CE 3.x Display Driver Issue Date: 01/10/19 S1D13A04 X37A-E-006-01 Page 10 Epson Research and Development Vancouver Design Center This option should remain disabled unless you are performing specific debugging tasks that require the debug monitor. MonoPanel This option is intended for the support of monochrome panels only. The option causes palette colors to be grayscaled for correct display on a mono panel. For use with color panels this option should not be enabled. DEBUG_BLT This option enables special BLT debugging messages on the debugging serial port. This option, when enabled, will drastically impact display driver performance, and should only be used to track down failures in the BLT operations. This option should be disabled unless doing BLT debugging. Mode File A second variable which will affect the finished display driver is the register configurations contained in the mode file. The MODE tables (contained in files MODE0.H, MODE1.H, MODE2.H . . .) contain register information to control the desired display mode. The MODE tables must be generated by the configuration program 13A04CFG.EXE. The display driver comes with one example MODE table: * MODE0.H - LCD 8-bit STN color, 320x240, 8bpp, 70Hz By default, only MODE0.H is used by the display driver. New mode tables can be created using the 13A04CFG program. Edit the #include section of MODE.H to add the new mode table. If you only support a single mode table, you do not need to add any information to the WinCE registry. If, however, you support more that one display mode, you should create registry values (see below) that will establish the initial display mode. If your display driver contains multiple mode tables, and if you do not add any registry values, the display driver will default to the first mode table in your list. To select which display mode the display driver should use upon boot, add the following lines to your PLATFORM.REG file: [HKEY_LOCAL_MACHINE\Drivers\Display\S1D13A04] S1D13A04 X37A-E-006-01 Windows(R) CE 3.x Display Driver Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 11 "Width"=dword:140 "Height"=dword:F0 "Bpp"=dword:8 "Rotation"=dword:0 Note that all dword values are in hexadecimal, therefore 140h = 320 and F0h = 240. When the display driver starts, it will read these values in the registry and attempt to match a mode table against them. All values must be present and valid for a match to occur, otherwise the display driver will default to the first mode table in your list. A WinCE desktop application (or control panel applet) can change these registry values, and the display driver will select a different mode upon warmboot. This allows the display driver to support different display configurations and/or orientations. An example application that controls these registry values will be made available upon the next release of the display driver; preliminary alpha code is available by special request. Resource Management Issues The Windows CE 3.0 OEM must deal with certain display driver issues relevant to Windows CE 3.0. These issues require the OEM balance factors such as: system vs. display memory utilization, video performance, and power off capabilities. The section "Simple Display Driver Configuration" on page 13 provides a configuration which should work with most Windows CE platforms. This section is only intended as a means of getting started. Once the developer has a functional system, it is recommended to optimize the display driver configuration as described below in "Description of Windows CE Display Driver Issues". Description of Windows CE Display Driver Issues The following are some issues to consider when configuring the display driver to work with Windows CE: 1. When Windows CE enters the Suspend state (power-off), the LCD controller and display memory may lose power, depending on how the OEM sets up the system. If display memory loses power, all images stored in display memory are lost. If power-off/power-on features are required, the OEM has several options: * If display memory power is turned off, add code to the display driver to save any images in display memory to system memory before power-off, and add code to restore these images after power-on. * If display memory power is turned off, instruct Windows CE to redraw all images upon power-on. Unfortunately it is not possible to instruct Windows CE to redraw any off-screen images, such as icons, slider bars, etc., so in this case the OEM must also configure the display driver to never use off-screen memory. * Ensure that display memory never loses power. Windows(R) CE 3.x Display Driver Issue Date: 01/10/19 S1D13A04 X37A-E-006-01 Page 12 Epson Research and Development Vancouver Design Center 2. Using off-screen display memory significantly improves display performance. For example, slider bars appear more smooth when using off-screen memory. To enable or disable the use of off-screen memory, edit the file: x:\wince300\platform\cepc\drivers\display\S1D13A04\sources. In SOURCES, there is a line which, when uncommented, will instruct Windows CE to use off-screen display memory (if sufficient display memory is available): CDEFINES=$(CDEFINES) -DEnablePreferVmem 3. In the file PROJECT.REG under CE 3.0, there is a key called PORepaint (search the Windows CE directories for PROJECT.REG). PORepaint is relevant when the Suspend state is entered or exited. PORepaint can be set to 0, 1, or 2 as described below: a. PORepaint=0 * * * * * This mode tells Windows CE not to save or restore display memory on suspend or resume. Since display data is not saved and not repainted, this is the FASTEST mode. Main display data in display memory must NOT be corrupted or lost on suspend. The memory clock must remain running. Off-screen data in display memory must NOT be corrupted or lost on suspend. The memory clock must remain running. This mode cannot be used if power to the display memory is turned off. b. PORepaint=1 * * * * This is the default mode for Windows CE. This mode tells Windows CE to save the main display data to the system memory on suspend. This mode is used if display memory power is going to be turned off when the system is suspended, and there is enough system memory to save the image. Any off-screen data in display memory is LOST when suspended. Therefore off-screen memory usage must either be disabled in the display driver (i.e: EnablePreferVmem not defined in SOURCES file), or new OEM-specific code must be added to the display driver to save off-screen data to system memory when the system is suspended, and restored when resumed. If off-screen data is used (provided that the OEM has provided code to save off-screen data when the system suspends), additional code must be added to the display driver's surface allocation routine to prevent the display driver from allocating the "main memory save region" in display memory. When WinCE OS attempts to allocate a buffer to save the main display data, WinCE OS marks the allocation request as preferring display memory. We believe this is incorrect. Code must be added to prevent this specific allocation from being allocated in display memory - it MUST be allocated from system memory. Since the main display data is copied to system memory on suspend, and then simply copied back on resume, this mode is FAST, but not as fast as mode 0. * * S1D13A04 X37A-E-006-01 Windows(R) CE 3.x Display Driver Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 13 c. PORepaint=2 * * This mode tells WinCE to not save the main display data on suspend, and causes WinCE to REPAINT the main display on resume. This mode is used if display memory power is going to be turned off when the system is suspended, and there is not enough system memory to save the image. Any off-screen data in display memory is LOST, and since there is insufficient system memory to save display data, off-screen memory usage MUST be disabled. When the system is resumed, WinCE instructs all running applications to repaint themselves. This is the SLOWEST of the three modes. * * Simple Display Driver Configuration The following display driver configuration should work with most platforms running Windows CE. This configuration disables the use of off-screen display memory and forces the system to redraw the main display upon power-on. 1. This step disables the use of off-screen display memory. Edit the file x:\wince300\platform\cepc\drivers\display\S1D13A04\sources and change the line CDEFINES=$(CDEFINES) -DEnablePreferVmem to #CDEFINES=$(CDEFINES) -DEnablePreferVmem 2. This step causes the system to redraw the main display upon power-on. This step is only required if display memory loses power when Windows CE is shut down. If display memory is kept powered up (set the S1D13A04 in powersave mode), then the display data will be maintained and this step can be skipped. Search for the file PROJECT.REG in your Windows CE directories, and inside PROJECT.REG find the key PORepaint. Change PORepaint as follows: "PORepaint"=dword:2 Windows(R) CE 3.x Display Driver Issue Date: 01/10/19 S1D13A04 X37A-E-006-01 Page 14 Epson Research and Development Vancouver Design Center Comments * The display driver is CPU independent, allowing use of the driver for several Windows CE Platform Builder supported platforms. The file s1dflat.cpp will require editing for the correct values of PhysicalPortAddr, PhysicalVmemAddr, etc. * The sample code defaults to a 320x240 8-bit color passive LCD panel in SwivelView 0 mode (landscape) with a color depth of 8 bpp. To support other settings, use 13A04CFG.EXE to generate a proper MODE0.H file. For further information, refer to the 13A04CFG Configuration Program User Manual, document number X37A-B-001xx. * By default, the 13A04CFG program assumes PCI addressing for the S5U13A04B00C evaluation board. This means that the display driver will automatically locate the S1D13A04 by scanning the PCI bus (currently only supported for the CEPC platform). If you select the address option "Other" and fill in your own custom addresses for the registers and video memory, then the display driver will not scan the PCI bus and will use the specific addresses you have chosen. * If you are running the display driver on hardware other than the S5U13A04B00C evaluation board, you must ensure that your hardware provides the correct clock frequencies for CLKI and CLKI2. 13A04CFG defaults to 50MHz for both CLKI and CLKI2. On the evaluation board, the display driver will correctly program the clock chip to support the CLKI and CLKI2 frequencies. On customer hardware, you must ensure that the clocks you provide to all clock inputs match the settings you chose in the Clocks tab of the 13A04CFG program. For more information on setting the clocks, see the 13A04CFG User Manual, document number X37A-B-001-xx. If you run the S1D13A04 with a single clock source, make sure your clock sources for PCLK, BCLK, and MCLK are correctly set to use the correct clock input source. Also ensure that you enable the clock dividers as required for different display hardware. * If you are using 13A04CFG.EXE to produce multiple MODE tables, make sure you change the Mode Number setting for each mode table you generate. The display driver supports multiple mode tables, but only if each mode table has a unique mode number. For more information on setting the mode number, see the 13A04CFG User Manual, document number X37A-B-001-xx. * The 13A04CFG program assumes you are using the S5U13A04B00C evaluation board, and defaults the Panel Power control to GPIO0. 13A04CFG allows you to change the GPIO pin used to control panel power, or to disable the use of GPIO pins altogether. If this is changed from the default, your driver will no longer be able to control panel power on the S5U13A04B00C evaluation board, and your panel may not be powered up correctly. * At this time, the driver has been tested on the x86 CPUs and have been run with Platform Builder v3.00. S1D13A04 X37A-E-006-01 Windows(R) CE 3.x Display Driver Issue Date: 01/10/19 S1D13A04 LCD/USB Companion Chip Windows(R) CE 3.x USB Driver Document Number: X37A-E-007-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation. All other trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-E-007-01 Windows(R) CE 3.x USB Driver Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 3 WINDOWS(R) CE 3.0 USB DRIVER The Windows CE v3.0 USB driver for the S1D13A04 LCD/USB Companion Chip is a client driver, which supports Microsoft ActiveSync 3.1. This driver is intended as "reference" source code for OEMs developing for the Microsoft Window CE platform and provide a basis for OEMs to develop their own drivers. This document and the source code for the Windows CE v3.0 USB driver is updated as appropriate. Before beginning any development, please check the Epson Research and Development Website at www.erd.epson.com for the latest revisions. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. Windows(R) CE 3.x USB Driver Issue Date: 01/10/19 S1D13A04 X37A-E-007-01 Page 4 Epson Research and Development Vancouver Design Center Example Driver Builds Build for CEPC (X86) on Windows CE Platform Builder 3.00 using the GUI Interface 1. Install Microsoft Windows 2000 Professional or Windows 98. 2. Install Platform Builder 3.00. 3. Start Platform Builder by double-clicking on the Microsoft Windows CE Platform Builder icon. 4. Create a new project. a. Select File | New. b. In the dialog box, select the Platforms tab. c. In the Platforms dialog box: - select "WCE Platform" - set a location for the project (such as x:\myproject) - set the platform name (such as myplatform) - set the processor to "Win32 (WCE x86)" d. Click the OK button. e. In the WCE Platform - Step 1 of 2 dialog box, select "CEPC". f. Click the Next button. g. In the WCE Platform - Step 2 of 2 dialog box, select "Maximum OS (Maxall)". h. Click the Finish button. i. In the New Platform Information dialog box, click the OK button. 5. Set the active configuration to "Win32 (WCE x86) Release". a. From the Build menu, select "Set Active Configuration". b. Select "MYPLATFORM - Win32 (WCE x86) Release". c. Click the OK button. 6. Add the environment variable USB_S1D13A04. a. From the Platform menu, select "Settings". b. Select the "Environment" tab. c. In the Variable box, type "USB_S1D13A04". d. In the Value box, type "1". e. Click the Set button. f. Click the OK button. S1D13A04 X37A-E-007-01 Windows(R) CE 3.x USB Driver Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 5 7. Create a new directory 13A04USB, under x:\wince300\platform\cepc\drivers, and copy the 13A04USB driver source code into this new directory. 8. Add the 13A04USB driver component. a. From the Platform menu, select "Insert | User Component". b. Set Files of type: to "All Files (*.*)". c. Select the file x:\wince300\platform\cepc\drivers\13A04USB\sources. d. Click the OK button. e. In the User Component Target File dialog box, select browse and then select the path/filename of the file sources. f. Click the OK button. 9. From the Platform window, click the Parameter View Tab. Show the tree for MYPLATFORM Parameters by clicking on the `+' sign at the root of the tree. Expand the the WINCE300 tree and then click the "Hardware Specific Files" and then double click the "PLATFORM.BIB". Edit the file platform.bib and make the following two changes: Find the section shown below, and insert the line as marked: IF IMGUSB IF CEPC_UHCI uhci.dll ENDIF IF CEPC_OHCI ohci.dll ENDIF usbd.dll usbhid.dll ENDIF IF USB_S1D13A04 ;Insert this line 13a04usb.dll $(_FLATRELEASEDIR)\13a04usb.dll NK SH ;Insert this line $(_FLATRELEASEDIR)\usbd.dll $(_FLATRELEASEDIR)\usbhid.dll NK SH NK SH $(_FLATRELEASEDIR)\ohci.dll NK SH $(_FLATRELEASEDIR)\uhci.dll NK SH ENDIF ;Insert this line ENDIF Windows(R) CE 3.x USB Driver Issue Date: 01/10/19 S1D13A04 X37A-E-007-01 Page 6 Epson Research and Development Vancouver Design Center 10. From the Platform window, click the Parameter View Tab. Show the tree for MYPLATFORM Parameters by clicking on the `+' sign at the root of the tree. Expand the WINCE300 tree and click the "Hardware Specific Files", then double click the "PLATFORM.REG". Insert the following section in the file platform.reg to include the settings for 13A04USB driver. [HKEY_LOCAL_MACHINE\Drivers\BuiltIn\13A0XUSB] "Dll"="13A04USB.dll" "Prefix"="COM" "Tsp"="Unimodem.dll" "DeviceArrayIndex"=dword:1 "Order"=dword:2 "DeviceType"=dword:0 "FriendlyName"="S1D13A04 USB" "DevConfig"=hex: 10,00, 00,00, 05,00,00,00, 10,01,00,00, 00,4B,00,00, 00,00, 08, 00, 00, 00,00,00,00 ; "PhysicalAddress"=dword:0x08000000 ; for non-cepc environment only ; "IRQ"=dword:05 ; for non-cepc environment only 11. From the Build menu, select "Rebuild Platform" to generate a Windows CE image file (nk.bin) in the project directory x:\myproject\myplatform\reldir\x86_release\nk.bin. S1D13A04 X37A-E-007-01 Windows(R) CE 3.x USB Driver Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 7 Installation and Execution from CEPC Environment Once the nk.bin file is built, the CEPC environment can be started by booting either from a floppy (step 1) or a hard drive (step 2) configured with a Windows 9x operating system. Both methods are described below. 1. To start CEPC by booting from a floppy drive: a. Create a bootable floppy disk. b. Copy himem.sys to the floppy disk and edit config.sys on the floppy disk to contain only the following line: device=a:\himem.sys c. Edit autoexec.bat on the floppy disk to contain the following line: loadcepc /B:38400 /C:1 c:\nk.bin d. Search for loadcepc.exe in your Windows CE directories, and copy the file to the bootable floppy disk. e. Copy nk.bin to c:\. f. Boot the system from the bootable floppy disk. 2. To start CEPC by booting from a hard drive: a. Search for loadcepc.exe in the Windows CE directories, and copy the file to C:\. b. Edit config.sys on the hard drive to contain only the following line: device=c:\himem.sys c. Edit autoexec.bat on the hard drive to contain the following line: loadcepc /B:38400 /C:1 c:\nk.bin d. Copy nk.bin to C:\. e. Boot the system 3. Install Windows 2000 Professional on a host machine. 4. Install ActiveSync 3.1 on the host machine. 5. Install the included wceusbsh.sys on the host machine, by following the procedures below: a. Unzip the file wceusbsh.zip to a directory on your hard drive. b. Find the file wceusbsh.inf. c. Right click the "WCEUSBSH.INF" file icon. d. Select Install. Windows(R) CE 3.x USB Driver Issue Date: 01/10/19 S1D13A04 X37A-E-007-01 Page 8 Epson Research and Development Vancouver Design Center 6. Connect a USB cable from the USB device (S5U13A04B00C board) to the USB host machine. 7. Boot the Windows CE machine from a floppy (created in step 1) or from the hard drive (created in step 2). 8. From the Windows CE desktop: - click the Start button - click Run - click Browse. 9. Find the file repllog.exe (by default it resides in \windows) and select it. 10. Click the OK button. The ActiveSync window on the host desktop is automatically invoked, and the New Partnership window is opened automatically. This window prompts: "Would you like to set up a partnership?" 11. Click the No button. 12. Click the Next button. 13. The Microsoft ActiveSync Window is opened automatically and should display "Guest connected". 14. Click the "Explore" button from the Microsoft ActiveSync window. File transfers are now possible through the USB cable. Compile Switches There are switches specific to the S1D13A04 USB driver which affect the USB driver. These switches are added or removed from the compile switches in the file sources. CEPC This option must be set for the CEPC platform and removed for all other platforms. EPSONMESSAGES This debugging option enables the display of EPSON-specific debug messages. These debug message are sent to the serial debugging port. This option should be disabled unless you are debugging the USB driver, as they will significantly impact the performance of the USB driver. S1D13A04 X37A-E-007-01 Windows(R) CE 3.x USB Driver Issue Date: 01/10/19 Epson Research and Development Vancouver Design Center Page 9 Address and IRQ Modifications * The USB driver is CPU independent, and it can be used on other platforms that support USB under Windows CE Platform Builder 3.0. If this driver is to support non-cepc platforms, the file project.reg requires editing to set the correct values of "PhysicalAddress" and "IRQ". * The variables DEFAULT_PHYSICAL_ADDRESS and DEFAULT_IRQ in the file 13a0xhw.h must be changed to reflect the values required by each implementation. * If the entries of "PhysicalAddress" and "IRQ" are removed from the project.reg file, the USB driver uses the values of DEFAULT_PHYSICAL_ADDRESS and DEFAULT_IRQ contained in the file 13a0xhw.h. Windows(R) CE 3.x USB Driver Issue Date: 01/10/19 S1D13A04 X37A-E-007-01 Page 10 Epson Research and Development Vancouver Design Center Comments * S5U13A04B00C Evaluation Board must be configured to enable USB support. This includes configuration changes to the dip switch and confirming that the proper USBClk is available on U13. See the S5U13A04B00C Rev. 1.0 Evaluation Board User Manual, document number X37A-G-004-xx. * This USB driver is independent of the S1D13A04 Windows CE v3.x display driver, but may be run together with S1D13A04 display driver. For information on the S1D13A04 CE Display Driver, see the Windows CE 3.x Display Driver, document number X37AE-006-xx. * At this time, the driver has been tested on the x86 CPUs and has been run with Platform Builder v3.00. S1D13A04 X37A-E-007-01 Windows(R) CE 3.x USB Driver Issue Date: 01/10/19 S1D13XXX 32-Bit Windows Device Driver Installation Guide Document No. X00A-E-003-04 Copyright (c) 1999, 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All Trademarks are the property of their respective owners Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK X00A-E-003-04 S1D13XXX 32-Bit Windows Device Driver Installation Guide Issue Date: 01/04/17 Epson Research and Development Vancouver Design Center Page 3 S1D13XXX 32-Bit Windows Device Driver Installation Guide This manual describes the installation of the Windows 9x/ME/NT 4.0/2000 device drivers for the S5U13xxxB00x series of Epson Evaluation Boards. The file S1D13XXX.VXD is required for using the Epson supplied Intel32 evaluation and test programs for the S1D13xxx family of LCD controllers with Windows 9x/ME. The file S1D13XXX.SYS is required for using the Epson supplied Intel32 evaluation and test programs for the S1D13xxx family of LCD controllers with Windows NT 4.0/2000. The file S1D13XXX.INF is the install script. For updated drivers, ask your Sales Representative or visit Epson Electronics America on the World Wide Web at www.eea.epson.com. Driver Requirements Video Controller Display Type BIOS DOS Program Dos Version Windows Program Windows DOS Box Windows Full Screen OS/2 : S1D13xxx : N/A : N/A : No : N/A : Yes, Windows 9x/ME/NT : N/A : N/A : N/A 4.0/2000 device driver Installation Windows NT Version 4.0 All evaluation boards require the driver to be installed as follows. 1. Install the evaluation board in the computer and boot the computer. 2. Copy the files S1D13XXX.INF and S1D13XXX.SYS to a directory on a local hard drive. 3. Right click your mouse on the file S1D13XXX.INF and select INSTALL from the menu. 4. Windows will install the device driver and ask you to restart. S1D13XXX 32-Bit Windows Device Driver Installation Guide Issue Date: 01/04/17 X00A-E-003-04 Page 4 Epson Research and Development Vancouver Design Center Windows 2000 All PCI Bus Evaluation Cards 1. Install the evaluation board in the computer and boot the computer. 2. Windows will detect the new hardware as a new PCI Device and bring up the FOUND NEW HARDWARE dialog box. 3. Click NEXT. 4. The New Hardware Wizard will bring up the dialog box to search for a suitable driver. 5. Click NEXT. 6. When Windows does not find the driver it will allow you to specify the location of it. Type the driver location or select BROWSE to find it. 7. Click NEXT. 8. Windows 2000 will open the installation file and show the option EPSON PCI Bridge Card. Select this file and click OPEN. 9. Windows then shows the path to the file. Click OK. 10. Click NEXT. 11. Click FINISH. All ISA Bus Evaluation Cards 1. Install the evaluation board in the computer and boot the computer. 2. Go to the CONTROL PANEL and select ADD/REMOVE HARDWARE, click NEXT. 3. Select ADD/TROUBLESHOOT A DEVICE, and click NEXT. Windows 2000 will attempt to detect any new plug and play device and fail. 4. The CHOOSE HARDWARE DEVICE dialog box appears. Select ADD NEW HARDWARE and click NEXT. 5. Select NO I WANT TO SELECT FROM A LIST and click NEXT. 6. Select OTHER DEVICE from the list and click NEXT. 7. Click HAVE DISK. 8. Specify the location of the driver files, select the S1D13XXX INF file and click OPEN. 9. Click OK. X00A-E-003-04 S1D13XXX 32-Bit Windows Device Driver Installation Guide Issue Date: 01/04/17 Epson Research and Development Vancouver Design Center Page 5 Windows 98/ME All PCI Bus Evaluation Cards 1. Install the evaluation board in the computer and boot the computer. 2. Windows will detect the new hardware as a new PCI Device and bring up the ADD NEW HARDWARE dialog box. 3. Click NEXT. 4. Windows will look for the driver. When Windows does not find the driver it will allow you to specify the location of it. Type the driver location or select BROWSE to find it. 5. Click NEXT. 6. Windows will open the installation file and show the option EPSON PCI Bridge Card. 7. Click FINISH. All ISA Bus Evaluation Cards 1. Install the evaluation board in the computer and boot the computer. 2. Go to the CONTROL PANEL and double-click on ADD NEW HARDWARE to launch the ADD NEW HARDWARE WIZARD. Click NEXT. 3. Windows will attempt to detect any new plug and play device and fail. Click NEXT. 4. Windows will ask you to let it detect the hardware, or allow you to select from a list. Select NO, I WANT TO SELECT THE HARDWARE FROM A LIST and click NEXT. 5. From the list select OTHER DEVICES and click NEXT. 6. Click HAVE DISK and type the path to the driver files, or select browse to find the driver. 7. Click OK. 8. The driver will be identified as EPSON PCI Bridge Card. Click NEXT. 9. Click FINISH. S1D13XXX 32-Bit Windows Device Driver Installation Guide Issue Date: 01/04/17 X00A-E-003-04 Page 6 Epson Research and Development Vancouver Design Center Windows 95 OSR2 All PCI Bus Evaluation Cards 1. Install the evaluation board in the computer and boot the computer. 2. Windows will detect the card as a new PCI Device and launch the UPDATE DEVICE DRIVER wizard. If The Driver is on Floppy Disk 3. Place the disk into drive A: and click NEXT. 4. Windows will find the EPSON PCI Bridge Card. 5. Click FINISH to install the driver. 6. Windows will ask you to restart the system. If The Driver is not on Floppy Disk 3. Click NEXT, Windows will search the floppy drive and fail. 4. Windows will attempt to load the new hardware as a Standard VGA Card. 5. Click CANCEL. The Driver must be loaded from the CONTROL PANEL under ADD/NEW HARDWARE. 6. Select NO for Windows to DETECT NEW HARDWARE. 7. Click NEXT. 8. Select OTHER DEVICES from HARDWARE TYPE and Click NEXT. 9. Click HAVE DISK. 10. Specify the location of the driver and click OK. 11. Click OK. 12. EPSON PCI Bridge Card will appear in the list. 13. Click NEXT. 14. Windows will install the driver. 15. Click FINISH. 16. Windows will ask you to restart the system. 17. Windows will re-detect the card and ask you to restart the system. X00A-E-003-04 S1D13XXX 32-Bit Windows Device Driver Installation Guide Issue Date: 01/04/17 Epson Research and Development Vancouver Design Center Page 7 All ISA Bus Evaluation Cards 1. Install the evaluation board in the computer and boot the computer. 2. Go to the CONTROL PANEL and select ADD NEW HARDWARE. 3. Click NEXT. 4. Select NO and click NEXT. 5. Select OTHER DEVICES and click NEXT. 6. Click Have Disk. 7. Specify the location of the driver files and click OK. 8. Click Next. 9. Click Finish. Previous Versions of Windows 95 All PCI Bus Evaluation Cards 1. Install the evaluation board in the computer and boot the computer. 2. Windows will detect the card. 3. Select DRIVER FROM DISK PROVIDED BY MANUFACTURER. 4. Click OK. 5. Specify a path to the location of the driver files. 6. Click OK. 7. Windows will find the S1D13XXX.INF file. 8. Click OK. 9. Click OK and Windows will install the driver. S1D13XXX 32-Bit Windows Device Driver Installation Guide Issue Date: 01/04/17 X00A-E-003-04 Page 8 Epson Research and Development Vancouver Design Center All ISA Bus Evaluation Cards 1. Install the evaluation board in the computer and boot the computer. 2. Go to the CONTROL PANEL and select ADD NEW HARDWARE. 3. Click NEXT. 4. Select NO and click NEXT. 5. Select OTHER DEVICES from the HARDWARE TYPES list. 6. Click HAVE DISK. 7. Specify the location of the driver files and click OK. 8. Select the file S1D13XXX.INF and click OK. 9. Click OK. 10. The EPSON PCI Bridge Card should be selected in the list window. 11. Click NEXT. 12. Click NEXT. 13. Click Finish. X00A-E-003-04 S1D13XXX 32-Bit Windows Device Driver Installation Guide Issue Date: 01/04/17 S1D13A04 LCD/USB Companion Chip S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Document Number: X37A-G-004-02 Copyright (c) 2001, 2002 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All other trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center Page 3 Table of Contents 1 2 3 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Installation and Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.1 Configuration DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.2 Configuration Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 CPU Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.1 CPU Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . 14 4.2 CPU Bus Connector Pin Mapping . . . . . . . . . . . . . . . . . . . . . . 15 LCD Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 . . . . . . . . . . . . ....... ...... ...... ...... ...... ...... ...... ...... ........ ........ ...... ........ 19 19 19 19 19 20 20 20 20 21 21 21 4 5 6 Technical Description . . . . . . . . . . . . . . . . . . . . . . . . . 6.1 PCI Bus Support . . . . . . . . . . . . . . . . . . . . . . 6.2 Direct Host Bus Interface Support . . . . . . . . . . . . . . . 6.3 S1D13A04 Embedded Memory . . . . . . . . . . . . . . . . 6.4 Adjustable LCD Panel Negative Power Supply . . . . . . . . . . 6.5 Adjustable LCD Panel Positive Power Supply . . . . . . . . . . . 6.6 Software Adjustable LCD Backlight Intensity Support Using PWM . . 6.7 LCD Panel Support . . . . . . . . . . . . . . . . . . . . . 6.7.1 Direct LCD Connector . . . . . . . . . . . . . . . . . . . . . . . 6.7.2 Extended LCD Connector . . . . . . . . . . . . . . . . . . . . . . 6.8 USB Support . . . . . . . . . . . . . . . . . . . . . . . . 6.8.1 USB IRQ Support . . . . . . . . . . . . . . . . . . . . . . . . . . 7 8 Clock Synthesizer and Clock Options . . . . . . . . . . . . . . . . . . . . . . . . 22 7.1 Clock Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 8.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 9 10 Schematics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 11 Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 12 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 12.1 Epson Companion Chips (S1D13A04) . . . . . . . . . . . . . . . . . . . . . 33 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 X37A-G-004-02 Page 4 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center Page 5 List of Tables Table 3-1: Table 3-2: Table 4-1: Table 4-2: Table 4-3: Table 5-1: Table 5-2: Table 9-1: Configuration DIP Switch Settings . . Jumper Summary . . . . . . . . . . . CPU Interface Pin Mapping . . . . . . CPU Bus Connector (H3) Pinout . . . CPU Bus Connector (H4) Pinout . . . LCD Signal Connector (H1) . . . . . . Extended LCD Signal Connector (H2) Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 11 14 15 16 17 18 24 List of Figures Figure 3-1: Figure 3-2: Figure 3-3: Figure 3-4: Figure 3-5: Figure 3-6: Figure 7-1: Figure 10-1: Figure 10-2: Figure 10-3: Figure 10-4: Figure 10-5: Figure 10-6: Figure 11-1: Configuration DIP Switch (SW1) Location Configuration Jumper (JP1) Location . . . Configuration Jumper (JP2) Location . . . Configuration Jumper (JP3) Location . . . Configuration Jumper (JP4) Location . . . Configuration Jumper (JP5) Location . . . Symbolic Clock Synthesizer Connections . S1D13A04B00C Schematics (1 of 6) . . . S1D13A04B00C Schematics (2 of 6) . . . S1D13A04B00C Schematics (3 of 6) . . . S1D13A04B00C Schematics (4 of 6) . . . S1D13A04B00C Schematics (5 of 6) . . . S1D13A04B00C Schematics (6 of 6) . . . S5U13A04B00C Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 . 11 . 12 . 12 . 13 . 13 . 22 . 26 . 27 . 28 . 29 . 30 . 31 . 32 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 X37A-G-004-02 Page 6 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center Page 7 1 Introduction This manual describes the setup and operation of the S5U13A04B00C Rev. 1.0 Evaluation Board. The board is designed as an evaluation platform for the S1D13A04 LCD/USB Companion Chip. This user manual is updated as appropriate. Please check the Epson Research and Development Website at www.erd.epson.com for the latest revision of this document before beginning any development. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 X37A-G-004-02 Page 8 Epson Research and Development Vancouver Design Center 2 Features Following are some features of the S5U13A04B00C Rev. 1.0 Evaluation Board: * 121-pin PFBGA S1D13A04 Embedded Memory LCD Controller with 160K bytes of embedded SRAM. * PCI bus operation through onboard PCI bridge. * CPU/Bus interface header strips for non-PCI bus operation. * Configuration options. * On-board adjustable positive LCD bias power supply from +23V to +40V. * On-board adjustable negative LCD bias power supply from -14V to -24V. * Software adjustable backlight intensity support using PWMOUT. * 4/8-bit 3.3V or 5V single monochrome passive LCD panel support. * 4/8/16-bit 3.3V or 5V single color passive LCD panel support. * 9/12/18-bit 3.3V or 5V active matrix TFT LCD panel support. * Direct interface for 18-bit Epson D-TFD LCD panel support. * Direct interface for 18-bit Sharp HR-TFT LCD panel support. * Programmable clock synthesizer to CLKI and CLKI2 for maximum clock flexibility. * Connector for USB client support. * Software initiated power save mode. * Selectable clock source for CLKI and CLKI2. * External oscillator support for CLKI and CLKI2. S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center Page 9 3 Installation and Configuration The S5U13A04B00C is designed to support as many platforms as possible. The S5U13A04B00C incorporates a DIP switch and five jumpers which allow both the evaluation board and the S1D13A04 LCD controller to be configured for a specified evaluation platform. 3.1 Configuration DIP Switches The S1D13A04 has configuration inputs (CNF[6:0]) which are read on the rising edge of RESET#. In order to configure the S1D13A04 for multiple Host Bus Interfaces an eightposition DIP switch (SW1) is required. The following figure shows the location of DIP switch SW1 on the S5U13A04B00C. DIP Switch - SW1 Figure 3-1: Configuration DIP Switch (SW1) Location S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 X37A-G-004-02 Page 10 Epson Research and Development Vancouver Design Center The S1D13A04 has seven configuration inputs (CONF[6:0]) which are read on the rising edge of RESET#. All S1D13A04 configuration inputs are fully configurable using an eight position DIP switch as described below. Table 3-1: Configuration DIP Switch Settings Switch (SW1) S1D13A04 Signal Value on this pin at rising edge of RESET# is used to configure: Closed (On/1) Open (Off/0) Select host bus interface as follows: CNF4 CNF2 CNF1 CNF0 Host Bus Interface 1 0 0 0 SH-4/SH-3 interface, Big Endian 0 0 0 0 SH-4/SH-3 interface, Little Endian 1 0 0 1 MC68K #1, Big Endian 0 0 0 1 Reserved 1 0 1 0 MC68K #2, Big Endian 0 0 1 0 Reserved 1 0 1 1 Generic #1, Big Endian 0 0 1 1 Generic #1, Little Endian 1 1 0 0 Reserved 0 1 0 0 Generic #2, Little Endian 1 1 0 1 RedCap 2, Big Endian 0 1 0 1 Reserved 1 1 1 0 DragonBall, Big Endian 0 1 1 0 Reserved X 1 1 1 Reserved Configure GPIO[7:6] and GPIO[4:0] as outputs and GPIO5 as an input at power-on (for use when USB is selected) WAIT# is active low CLKI to BCLK divide ratio 1:1 Enable PCI bridge for PCI host SW1-5, SW1-[3:1] CNF4, CNF[2:0] SW1-4 SW1-6 SW1-7 SW1-8 CNF3 CNF5 CNF6 - Configure GPIO pins as inputs at power-on WAIT# is active high CLKI to BCLK Divide ratio 2:1 Disable PCI bridge for non-PCI host = Required settings when used with PCI Bridge FPGA S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center Page 11 3.2 Configuration Jumpers The S5U13A04B00C has five jumper blocks which configure various setting on the board. The jumper positions for each function are shown below. Table 3-2: Jumper Summary Jumper JP1 JP2 JP3 JP4 JP5 Function CLKI Source CLKI2 Source LCD Panel Voltage GP0I0 Polarity on H1 GPIO0 function select = recommended settings Position 1-2 VCLKOUT from clock synthesizer MCLKOUT from clock synthesizer +5V LCDVCC Normal (Active High) GPIO0 Position 2-3 External oscillator (U7) External oscillator (U8) +3.3V LCDVCC Inverted (Active Low) HR-TFT PS signal No Jumper BUSCLK from Header H4 -- -- GPIO0 not sent to H1 -- JP1 - CLKI Source JP1 selects the source for the CLKI input pin. Position 1-2 sets the CLKI source to VCLKOUT from the Cypress clock synthesizer (default setting). Position 2-3 sets the CLKI source to the external oscillator at U7. When no jumper is installed, the CLKI source is set to the BUSCLK signal from Header H4. JP1 VCLKOUT from clock synthesizer External oscillator (U7) BUSCLK from Header H4 Figure 3-2: Configuration Jumper (JP1) Location S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 X37A-G-004-02 Page 12 Epson Research and Development Vancouver Design Center JP2 - CLKI2 Source JP2 selects the source for the CLKI2 input pin. Position 1-2 sets the CLKI2 source to MCLKOUT from the Cypress clock synthesizer (default setting). Position 2-3 sets the CLKI2 source to the external oscillator at U8. JP2 MCLKOUT from clock synthesizer External oscillator (U8) Figure 3-3: Configuration Jumper (JP2) Location JP3 - LCD Panel Voltage JP3 selects the voltage level to the LCD panel. Position 1-2 sets the voltage level to 5.0V (default setting). Position 2-3 sets the voltage level to 3.3V. Note When configured for Sharp HR-TFT or Epson D-TFD panels, JP3 and JP5 must be set to position 2-3. JP3 +5 LCDVCC +3.3 LCDVCC Figure 3-4: Configuration Jumper (JP3) Location S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center Page 13 JP4 - GPIO0 Polarity on H1 JP4 selects the polarity of the GPIO0 signal available on the LCD Connector H1. Position 1-2 sends the GPIO0 signal directly to H1 (default setting). Position 2-3 inverts the GPIO0 signal before sending it to H1. When no jumper is installed, GPIO0 is not sent to H1. JP4 Normal (Active High) Inverted (Active Low) GPIO0 not sent to H1 Figure 3-5: Configuration Jumper (JP4) Location JP5 - GPIO0 Selection JP5 selects the function of the GPIO0 signal. Position 1-2 GPIO0 used to control the LCD bias power supplies for STN panels. Position 2-3 GPIO0 used as the PS signal when the S1D13A04 is configured for HR-TFT panel type. JP5 GPIO0 HR-TFT PS signal Figure 3-6: Configuration Jumper (JP5) Location S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 X37A-G-004-02 Page 14 Epson Research and Development Vancouver Design Center 4 CPU Interface 4.1 CPU Interface Pin Mapping Table 4-1: CPU Interface Pin Mapping S1D13A04 Pin Name Hitachi Motorola Generic #1 Generic #2 SH-3 /SH-4 MC68K #1 A[17:1] A01 D[15:0] A[17:1] A0 D[15:0] A[17:1] A01 D[15:0] CSn# CKIO BS# RD/WR# RD# WE0# WE1# WAIT#/ RDY# RESET# A[17:1] LDS# D[15:0] Motorola MC68K #2 A[17:1] A0 D[15:0]2 Motorola REDCAP2 A[17:1] A01 D[15:0] CSn CLK Motorola MC68EZ328/ MC68VZ328 DragonBall A[17:1] A01 D[15:0] CSX CLK Connected to HIOVDD3 OE LWE UWE DTACK RESET AB[17:1] AB0 DB[15:0] CS# M/R# CLKI BS# RD/WR# RD# WE0# WE1# WAIT# RESET# External Decode BUSCLK BUSCLK 3 External Decode External Decode CLK AS# R/W# Connected to HIOVDD3 Connected to HIOVDD3 UDS# DTACK# RESET# CLK AS# R/W# SIZ1 SIZ0 DS# DSACK1# RESET# Connected to HIOVDD RD1# RD0# WE0# WE1# WAIT# RESET# Connected to HIOVDD3 R/W OE EB1 EB0 N/A RESET_OUT Connected to HIOVDD3 RD# WE# BHE# WAIT# RESET# Note 1 A0 for these busses is not used internally by the S1D13A04 and should be connected to VSS. 2 If the target MC68K bus is 32-bit, then these signals should be connected to D[31:16]. 3 These pins are not used in their corresponding host interface mode. Systems are responsible for externally connecting them to Host Interface IO VDD. S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center Page 15 4.2 CPU Bus Connector Pin Mapping Table 4-2: CPU Bus Connector (H3) Pinout Connector Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Comments Connected to DB0 of the S1D13A04 Connected to DB1 of the S1D13A04 Connected to DB2 of the S1D13A04 Connected to DB3 of the S1D13A04 Ground Ground Connected to DB4 of the S1D13A04 Connected to DB5 of the S1D13A04 Connected to DB6 of the S1D13A04 Connected to DB7 of the S1D13A04 Ground Ground Connected to DB8 of the S1D13A04 Connected to DB9 of the S1D13A04 Connected to DB10 of the S1D13A04 Connected to DB11 of the S1D13A04 Ground Ground Connected to DB12 of the S1D13A04 Connected to DB13 of the S1D13A04 Connected to DB14 of the S1D13A04 Connected to DB15 of the S1D13A04 Connected to RESET# of the S1D13A04 Ground Ground Ground +12 volt supply +12 volt supply Connected to WE0# of the S1D13A04 Connected to WAIT# of the S1D13A04 Connected to CS# of the S1D13A04 Connected to MR# of the S1D13A04 Connected to WE1# of the S1D13A04 Connected to +3.3V S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 X37A-G-004-02 Page 16 Epson Research and Development Vancouver Design Center Table 4-3: CPU Bus Connector (H4) Pinout Connector Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 Comments Connected to AB0 of the S1D13A04 Connected to AB1 of the S1D13A04 Connected to AB2 of the S1D13A04 Connected to AB3 of the S1D13A04 Connected to AB4 of the S1D13A04 Connected to AB5 of the S1D13A04 Connected to AB6 of the S1D13A04 Connected to AB7 of the S1D13A04 Ground Ground Connected to AB8 of the S1D13A04 Connected to AB9 of the S1D13A04 Connected to AB10 of the S1D13A04 Connected to AB11 of the S1D13A04 Connected to AB12 of the S1D13A04 Connected to AB13 of the S1D13A04 Ground Ground Connected to AB14 of the S1D13A04 Connected to AB15 of the S1D13A04 Connected to AB16 of the S1D13A04 Connected to AB17 of the S1D13A04 Not connected Not connected Ground Ground +5 volt supply +5 volt supply Connected to RD/WR# of the S1D13A04 Connected to BS# of the S1D13A04 Connected to BUSCLK of the S1D13A04 Connected to RD# of the S1D13A04 Not connected Not connected S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center Page 17 5 LCD Interface Pin Mapping Table 5-1: LCD Signal Connector (H1) Monochrome Passive Panel Pin Name Connector Pin No. 4-bit FPDAT0 FPDAT1 FPDAT2 FPDAT3 FPDAT4 FPDAT5 FPDAT6 FPDAT7 FPDAT8 FPDAT9 FPDAT10 FPDAT11 FPDAT12 FPDAT13 FPDAT14 FPDAT15 FPDAT16 FPDAT17 FPSHIFT DRDY FPLINE FPFRAME GND PWMOUT VLCD VCC +12V VDDH DISPLAY2 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 4 6 33 35 & 38 37 39 2, 8, 14, 20, 26 28 30 32 34 36 40 MOD FPSHIFT2 driven 0 driven 0 driven 0 driven 0 D0 D1 D2 D3 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 Color Passive Panel Single Format 1 Format 2 4-bit driven 0 driven 0 driven 0 driven 0 D0 (R2)1 D1 (B1)1 D2 (G1)1 D3 (R1)1 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 Color TFT Panel Others 16-Bit D0 (R6)1 D1 (G5)1 D2 (B4)1 D3 (R4)1 D8 (B5)1 D9 (R5)1 D10 (G4)1 D11 (B3)1 D4 (G3)1 D5 (B2)1 D6 (R2)1 D7 (G1)1 D12 (R3)1 D13 (G2)1 D14 (B1)1 D15 (R1)1 driven 0 driven 0 Single 8-bit D0 D1 D2 D3 D4 D5 D6 D7 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 Sharp HR-TFT 18-bit R5 R4 R3 G5 G4 G3 B5 B4 B3 R2 R1 R0 G2 G1 G0 B2 B1 B0 8-bit D0 (B5)1 D1 (R5)1 D2 (G4)1 D3 (B3)1 D4 (R3)1 D5 (G2) 1 8-bit D0 (G3)1 D1 (R3)1 D2 (B2)1 D3 (G2)1 D4 (R2)1 D5 (B1) 1 9-bit R2 R1 R0 G2 G1 G0 B2 B1 B0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 12-bit R3 R2 R1 G3 G2 G1 B3 B2 B1 R0 driven 0 driven 0 G0 driven 0 driven 0 B0 driven 0 driven 0 18-bit R5 R4 R3 G5 G4 G3 B5 B4 B3 R2 R1 R0 G2 G1 G0 B2 B1 B0 CLK GPO3 LP SPS D6 (B1)1 D7 (R1)1 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 D6 (G1)1 D7 (R1)1 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 driven 0 FPSHIFT MOD FPLINE FPFRAME GND PWMOUT DRDY Adjustable -24V to -14V negative LCD bias LCDVCC (3.3V or 5V) +12V Adjustable +23V to +40V positive LCD bias GPIO0 (for controlling on-board LCD bias power supply on/off) PS Note pin mappings use signal names commonly used for each panel type, however signal names may differ between panel manufacturers. The values shown in brackets represent the color components as mapped to the corresponding FPDATxx signals at the first valid edge of FPSHIFT. For further FPDATxx to LCD interface mapping, see S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. 2 DISPLAY can be disconnected from GPIO0 using JP5 (2-3 position) and can be inverted on H1 setting JP4 to 2-3. 3 When the 'Direct' HR-TFT interface is selected, DRDY becomes a general purpose output (GPO) controllable using the 'Direct' HR-TFT LCD Interface GPO Control bit (REG[14h] bit 0). This GPO can be used to control the HR-TFT MOD signal if required. For further information, see the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. 1 These S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 X37A-G-004-02 Page 18 Epson Research and Development Vancouver Design Center Table 5-2: Extended LCD Signal Connector (H2) Monochrome Passive Panel Pin Name Connector Pin No. Single 4-bit GPIO01 GPIO11 GPIO21 GPIO31 GPIO41 GPIO51 GPIO61 GPIO71 GND 1 3 5 7 9 11 13 15 2, 4, 6, 8, 10, 12, 14, 16 Color Passive Panel Single Format 1 Format 2 4-bit 8-bit 8-bit GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPIO7 GND Color TFT Panel Others 16-Bit 9-bit 12-bit 18-bit HRTFT2 18-bit PS CLS REV SPL GPIO0 GPIO1 GPIO2 GPIO3 USBPUP USBDET ECT USBDM USBDP USB3 8-bit Note 1 When Switch SW1-4 is open (CNF3 = 0 at RESET#), GPIO[7:6] and GPIO[4:0] are set as outputs at 0 (low state) and GPIO5 is set as an input at power-on/RESET# (for use when USB is selected). If SW1-4 is closed then GPIO[7:0] are set as inputs upon power-on/RESET#. 2 If the 'Direct' HR-TFT interface is selected (REG[0Ch] bits 1:0 = 10), GPIO[3:0] are used for the 'Direct' HR-TFT interface. GPIO[7:4] remain available for USB support or as GPIOs. 3 If USB support is enabled (REG[4000h] bit 7 = 1), GPIO[7:4] are used by the USB interface. GPIO[3:0] remain available for 'Direct' HR-TFT interface support or as GPIOs. S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center Page 19 6 Technical Description 6.1 PCI Bus Support The S1D13A04 does not have on-chip PCI bus interface support. The S1D13A04B00C uses the PCI Bridge FPGA to support the PCI bus. 6.2 Direct Host Bus Interface Support The S5U13A04B00C is specifically designed to work using the PCI Bridge FPGA in a standard PCI bus environment. However, the S1D13A04 directly supports many other host bus interfaces. Connectors H3 and H4 provide the necessary IO pins to interface to these host buses. For further information on the host bus interfaces supported, see "CPU Interface" on page 14. Note The PCI Bridge FPGA must be disabled using SW1-8 in order for direct host bus interface to operate properly. 6.3 S1D13A04 Embedded Memory The S1D13A04 has 160K bytes of embedded SRAM. The 160K byte display buffer address space is directly and contiguously available through the 18-bit address bus. 6.4 Adjustable LCD Panel Negative Power Supply Most monochrome passive LCD panels require a negative power supply to provide between -14V and -24V (Iout=45mA). Such a power supply (VLCD) has been provided on the S5U13A04B00C board. VLCD can be adjusted using potentiometer R39 to provide an output voltage from -14V to -24V, and is enabled/disabled using the S1D13A04 general purpose signal, GPIO0 (active high). Note When manually adjusting the voltage, set the potentiometer according to the panel's specific power requirements before connecting the panel. S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 X37A-G-004-02 Page 20 Epson Research and Development Vancouver Design Center 6.5 Adjustable LCD Panel Positive Power Supply Most color passive LCD panels and most single monochrome 640x480 passive LCD panels require a positive power supply to provide between +23V and +40V (Iout=45mA). Such a power supply (VDDH) has been provided on the S5U13A04B00C board. VDDH can be adjusted using R22 to provide an output voltage from +23V to +40V, and is enabled/disabled using the S1D13A04 general purpose signal, GPIO0 (active high). Note When manually adjusting the voltage, set the potentiometer according to the panel's specific power requirements before connecting the panel. 6.6 Software Adjustable LCD Backlight Intensity Support Using PWM The S1D13A04 provides Pulse Width Modulation output on PWMOUT. PWMOUT can be used to control LCD panels which support PWM control of the backlight inverter. The PWMOUT signal is provided on the LCD connector, H1. 6.7 LCD Panel Support The S1D13A04 directly supports: * Single-panel, single drive passive displays. * 4/8-bit monochrome interface. * 4/8/16-bit color interface. * Active Matrix TFT interface. * 9/12/18-bit interface. * 'Direct' support for 18-bit Sharp HR-TFT LCD or compatible interface. All the necessary signals are provided on the 40-pin LCD connector H1 and the 16-pin LCD connector H2. For connection information, refer to Table 5-1: "LCD Signal Connector (H1)" on page 17 and Table 5-2: "Extended LCD Signal Connector (H2)" on page 18. 6.7.1 Direct LCD Connector The direct LCD Connector (H1) provides all LCD panel signals required for Active Matrix TFT and Passive LCD panels. These signals are buffered to either a 3.3V level or a 5.0V level depending on the setting of JP3. See Table 3-2: "Jumper Summary" on page 11. S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center Page 21 6.7.2 Extended LCD Connector The S1D13A04 directly supports Sharp 18-bit HR-TFT and compatible panels. The extended LCD connector (H2) provides the extra signals required to support these panels. The signals on this connector are provided directly from the S1D13A04 without any buffering and are 3.3V signals. 6.8 USB Support The S1D13A04 USB controller provides a Revision 1.1 compliant USB client. The S1D13A04 acts as a USB device and connects to an upstream hub or USB host through connector J1 on the S5U13A04B00C evaluation board. Clamping diodes have been added to protect the USB bus from ESD and shorting. 6.8.1 USB IRQ Support The S1D13A04 supports interrupts through output pin, IRQ. This interrupt can be used to support interrupts from the USB client of the S1D13A04. The S5U13A04B00C evaluation board supports this capability by connecting IRQ to the PCI interrupt INTA# of the PCI slot that the S5U13A04B00C evaluation board is connected to. S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 X37A-G-004-02 Page 22 Epson Research and Development Vancouver Design Center 7 Clock Synthesizer and Clock Options For maximum flexibility, the S5U13A04B00C implements a Cypress ICD2061A Clock Synthesizer. MCLKOUT from the clock synthesizer is connected to CLKI2 of the S1D13A04 and VCLKOUT from the clock synthesizer is connected to CLKI of the S1D13A04. A 14.31818MHz crystal (Y1) is connected to XTALIN and XTALOUT of the clock synthesizer and provides the reference clock to the clock synthesizer. ICD2061A Synthesizer reference 14.31818 MHz XTALIN MCLKOUT CLKI2 VCLKOUT CLKI Figure 7-1: Symbolic Clock Synthesizer Connections At power-on, CLKI2 (MCLKOUT) is configured to be 40MHz and CLKI (VCLKOUT) is configured at 25.175MHz. Note If a Sharp HR-TFT panel is selected, the clock synthesizer cannot be programmed, and external oscillators must provide the clock signals to CLKI and CLKI2. Jumpers JP1 and JP2 allow selection of external oscillators U7 and U8 as the clock source for both CLKI and CLKI2. For further information, see Table 3-2: "Jumper Summary" on page 11. 7.1 Clock Programming The S1D13A04 utilities automatically program the clock generator. If manual programming of the clock generator is required, refer to the source code for the S1D13A04 utilities available on the internet at www.erd.epson.com. For further information on programming the clock generator, refer to the Cypress ICD2061A specification. Note When CLKI and CLKI2 are programmed to multiples of each other (e.g. CLKI = 20MHz, CLKI2 = 40MHz), the clock output signals from the Cypress clock generator may jitter. Refer to the Cypress ICD2061A specification for details. To avoid this problem, set CLKI and CLKI2 to different frequencies and use the S1D13A04 internal clock divides to obtain the lower frequencies. S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center Page 23 8 References 8.1 Documents * Epson Research and Development, Inc., S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. * Epson Research and Development, Inc., S1D13A04 Programming Notes and Examples, document number X37A-G-003-xx. * Cypress Semiconductor Corporation, ICD2061A Data Sheet. 8.2 Document Sources * Epson Research and Development: http://www.erd.epson.com. * Cypress Semiconductor Corporation Website: http://www.cypress.com. S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 X37A-G-004-02 Page 24 Epson Research and Development Vancouver Design Center 9 Parts List Table 9-1: Parts List Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Qty 25 1 2 7 3 1 9 2 2 1 1 2 5 1 1 1 1 1 13 8 6 3 1 1 2 2 1 Designation C1-C11,C15C21,C28,C30,C32-C35,C48 C12 C13,C14 C22,C2,C29,C31,C45,C46, C49 C23-C25 C27 C36-C44 C47,C50 D1,D2 H1 H2 H3,H4 JP1-JP5 J1 L1 L2 Q1 Q2 R1-R7,R23,R31,R34-R37 R8-R14,R16 R15,R17,R18,R32,R33,R38 R19,R20,R30 R21 R22 R24,R25 R26,R29 R27 Part Value 0.1u 10u,10V n/p 68u, 10V 10uF, 63V 56uF, 35V 0.22uF 33u, 20V BAV99 HEADER 20X2 HEADER 8X2 HEADER 17X2 HEADER 3 USB Type B 1uH Ferrite MMBT3906 MMBT2222A 15K, 5% 330K, 5% 1K, 5% 100K, 5% 470 Ohm, 5% 200K Pot 20 Ohm, 1% 301K, 1% 1.5K, 1% Description Ceramic Chip, 50V X7R +/-5%, 1206 pckg. Tantalum C-Size, +/-10% 1206 pckg. Tantalum D-Size, +/-10% Electrolytic, Radial Lead, +/-20% Electrolytic, Radial Lead, +/-20% Ceramic Chip, 50V X7R +/-5%, 1206 pckg. Tantalum D-Size, +/-10% Ultra high-speed switching diode 20x2, .025" sq. shrouded header, keyed Manufacturer / Part No. / Assembly Instructions Kemet C1206C104J5RAC Kemet T491C106K010AS Do not populate Kemet T491D86K010AS NIPPON/UNITED CHEMI-CON KMF63VB10RM5X11LL NIPPON/UNITED CHEMI-CON KMF35VB56RM5X11LL Kemet C1206C224J5RAC Kemet T491D33K020AS Rohm BAV99 Thomas&Betts P/N:636-4027 or equivalent 8x2, .025" sq. shrouded header, Thomas&Betts P/N:636-1627 or keyed equivalent 17x2, .025" sq. unshrouded header, right angle 3x1 .1" pitch unshrouded header Right Angle, Type B USB Connector Inductor Ferrite Bead PNP signal transistor, SOT23 package NPN transistor, SOT-23 pckg. 1206 Resistor 1206 Resistor 1206 Resistor 1206 Resistor 1206 Resistor 200K Trim Pot 1206 Resistor 1206 Resistor 1206 Resistor Bourns 3386W-1-204 AMP787780-1 RCD MCI-1812 1uH MT Phillips BDS3/3/8.9-4S2 Motorola MMBT3906LT1 Motorola MMBT2222A Thomas&Betts P/N:609-3407 or equivalent S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center Page 25 Table 9-1: Parts List Item 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 Qty 1 1 1 1 1 1 1 1 2 2 1 1 1 1 1 3 1 1 1 1 1 1 5 1 2 Designation R28 R39 SW1 SW2 U1 U2 U3 U4 U5,U6 U7,U8 U9 U10 U11 U12 U13 U14-U16 U17 U18 U19 Y1 Y2 U18 (JP1-JP5) Z1 Z2 Part Value 150K, 1% 100K Pot SW DIP-8 SW DIP-4 S1D13A04F0A LT1117CST-5 ICD2061A 74AHC04 NC7SZ04 Test Socket RD-0412 EPN001 NC7ST04 LT1118CST-2.5 LT1117CM-3.3 74HCT244 EPF6016TC14 4-2 EPC1441PC8 74HCT125 14.31818MHz 48MHz Osc Socket Shunts PCI Bracket Screw Description 1206 Resistor 100K Trim Pot Dip Switch, 8-Position DIP switch, 4-position 121-pin PFBGA 13A04 LCDC 5V fixed voltage regulator, SOT-223 Clock Chip, Wide SO-16 pckg Inverter, SO-14 package TinyLogic UHS inverter, SOT23-5 package 14 pin narrow DIP, screw machine socket Positive LCD Bias Power Supply Negative LCD Bias Power Supply TinyLogic HST inverter, SOT235 package 2.5V fixed volt reg / SOT-223 3.3V fixed volt reg / 3 Lead PlasticDD Buffer, SO-20 package 144-pin TQFP FLEX6000 FPGA 8-pin DIP pckg, OTP EPROM Buffer, SO-14 package Do Not Populate Supplied by Epson R&D Linear Technology LT1117CST5 Cypress ICD2061A TI74AHC04 Fairchild NC7SZ04 Sockets for oscillator input Taiyo Yuden/Xentek Positive Power Supply, RD-0412 Taiyo Yuden/Xentek Negative Power Supply, EPN001 Fairchild NC7ST04 Linear Technology LT1118CST2.5 Linear Technology LT1117CM3.3 TI74HCT244 Altera EPF6016TC144-2 Altera EPC1441PC8, socketed TI74HCT125 Bourns 3386W-1-104 Manufacturer / Part No. / Assembly Instructions 14.31818MHz crystal, Fox HCFOX FoxS/143-20 14.31818MHz 49 SMD 48MHz oscillator 4-pin narrow DIP, screw machine socket Jumper Shunts PCI bracket with slot for USB Type B connector Screw, pan head, #4-40 x 1/4" Hansen Industries Use to Assemble PCI bracket onto PCB board Epson SG-615PH-48.000MHz Socket for U18 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 X37A-G-004-02 Page 26 A1 A8 A11 B1 B4 B11 C1 C11 NC NC NC NC NC NC NC NC VSS VSS VSS VSS VSS VSS VSS NC NC NC NC NC NC COREVDD COREVDD COREVDD COREVDD SED13A04 A2 C2 J10 L10 +2.5V F6 H5 J1 J6 J11 K1 S1D13A04 X37A-G-004-02 5 4 3 2 1 D D U1 CNF[6:0] CNF0 CNF1 CNF2 CNF3 CNF4 CNF5 CNF6 FPDAT[17:0] FPDAT[17:0] A7 B7 C7 D7 B8 C8 C9 CNF0 CNF1 CNF2 CNF3 CNF4 CNF5 CNF6 CNF[6:0] AB[17:0] 10 Schematics AB[17:0] +3.3V 15K 5% R1 CNF[6:0] SW1 AB0 AB1 AB2 AB3 AB4 AB5 AB6 AB7 AB8 AB9 AB10 AB11 AB12 AB13 AB14 AB15 AB16 AB17 D1 D2 D3 C3 A3 B3 C4 A4 D4 C5 B5 A5 D5 E6 B6 A6 C6 D6 AB0 AB1 AB2 AB3 AB4 AB5 AB6 AB7 AB8 AB9 AB10 AB11 AB12 AB13 AB14 AB15 AB16 AB17 15K 5% R2 CNF0 CNF1 CNF2 CNF3 CNF4 CNF5 CNF6 1 2 3 4 5 6 7 8 SW DIP-8 16 15 14 13 12 11 10 9 15K 5% R3 15K 5% R4 15K 5% R5 15K 5% R6 15K 5% R7 C C FPDAT0 FPDAT1 FPDAT2 FPDAT3 FPDAT4 FPDAT5 FPDAT6 FPDAT7 FPDAT8 FPDAT9 FPDAT10 FPDAT11 FPDAT12 FPDAT13 FPDAT14 FPDAT15 FPDAT16 FPDAT17 H11 G8 G9 G10 G11 G7 F8 F10 F7 E8 E11 E10 E9 D8 D11 D10 D9 C10 FPDAT0 FPDAT1 FPDAT2 FPDAT3 FPDAT4 FPDAT5 FPDAT6 FPDAT7 FPDAT8 FPDAT9 FPDAT10 FPDAT11 FPDAT12 FPDAT13 FPDAT14 FPDAT15 FPDAT16 FPDAT17 nCONFIG DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8 DB9 DB10 DB11 DB12 DB13 DB14 DB15 L5 K5 J5 L4 K4 J4 J3 L3 K3 J2 H3 H2 H1 H4 G3 G2 DB0 DB1 DB2 DB3 DB4 DB5 DB6 DB7 DB8 DB9 DB10 DB11 DB12 DB13 DB14 DB15 R8 R9 330K 5% 330K 5% R10 R11 330K 5% 330K 5% GPO0 FPRAME FPLINE FPSHIFT DRDY GPIO0 GPIO1 GPIO2 GPIO3 PWMOUT A9 PWMOUT H8 J9 H9 H10 K9 L8 J7 K7 L7 GPO0 FPFRAME FPLINE FPSHIFT DRDY GPIO0 GPIO1 GPIO2 GPIO3 R14 R12 R13 330K 5% 330K 5% 330K 5% DB[15:0] F5 B9 J8 CLKI CLKI2 USBCLK GPIO4 GPIO5 GPIO6 GPIO7 IRQ NC NC NC HIOVDD HIOVDD +3.3V G4 L2 +3.3V K11 L1 L11 H7 G6 K6 L6 K8 GPIO4 GPIO5 GPIO6 GPIO7 IRQ DB[15:0] CLKI CLKI2 USBCLK B B CS# M/R# BS# RD# WE0# WE1# RD/WR# RESET# WAIT# CS# M/R# BS# RD# WE0# WE1# RD/WR# RESET# WAIT# TESTEN E7 NIOVDD NIOVDD NIOVDD NIOVDD E4 E3 E2 E1 E5 F4 F3 F1 G1 +3.3V A10 F11 H6 L9 +2.5V Figure 10-1: S1D13A04B00C Schematics (1 of 6) B2 B10 F2 F9 G5 K2 K10 C1 0.1u C2 0.1u C3 0.1u C4 0.1u C5 0.1u C6 0.1u C7 0.1u C8 0.1u Title Size B Date: 5 4 3 2 A A S5U13A04B00C Rev. 1.0 - S1D13A04B00A / DIP SW Document Number 1 Rev 1.0 1 of 6 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center 5 4 3 2 1 U2 LT1117CST-5 +12V VIN +3.3V 14 ADJ C9 0.1u U4A 2 C15 0.1u C16 0.1u B_MCLKOUT C17 0.1u +3.3V +3.3V +3.3V D 3 VOUT 2 D +5V 1 1 Epson Research and Development Vancouver Design Center + 74AHC04 7 C10 0.1u C11 0.1u C12 10u 10V For U4 13 U3 AVDD 1,5 1,5 5 +5V INIT0 INIT1 VCLKOUT PWRDWN# OE NC7SZ04 ERROUT# GND +3.3V 14 10 3 XTALIN XTALOUT FEATCLK INTCLK 5 ICD2061A U4B 9 2 4 B_VCLKOUT MCLKOUT 16 4 6 7 Y1 11 15 14.31818MHz 12 14 8 U5 GPIO1 GPIO2 S0/CLK S1/DATA VDD 1 2 +3.3V 3 JP1 B_VCLKOUT CLKI 1 +5V C20 0.1u 4 2 Y2 VDD GND 48MHz OSC 7 4 OE OUT 1 3 9 +3.3V 14 1 2 3 HEADER 3 +3.3V 5 U7 +5V VCC GND Test Socket NC7SZ04 3 6 BUSCLK OUT 8 2 NC C18 0.1u 7 14 1 U6 7 14 7 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 For U5 For U6 C C Not Populated 3 GPIO3 R15 15K 5% 4 1,5 C13 n/p C14 n/p 74AHC04 U4D 8 USBCLK 74AHC04 B 1 B JP2 B_MCLKOUT CLKI2 1 1 2 3 HEADER 3 +3.3V U8 +5V C19 0.1u 7 GND Test Socket 74AHC04 Title S5U13A04B00C Rev. 1.0 - Clocks Size B Date: 5 4 3 2 Figure 10-2: S1D13A04B00C Schematics (2 of 6) 14 VCC NC OUT 8 1 5 U4C 6 A A Document Number 1 Rev 1.0 2 of 6 S1D13A04 X37A-G-004-02 Page 27 Page 28 DC_IN REMOTE GND GND GND GND GND GND GND NC VOUT_ADJ DC_OUT 2 3 4 5 6 7 8 10 11 9 +5V 1 12 +5V 1 2 3 5 3 1 1 C C EPN001 R17 1K 5% 3 Q1 MMBT3906 U10 2 R16 330K 5% NC7ST04 3 15K 5% DC_IN DC_IN VOUT_ADJ GND GND NC NC NC NC DC_OUT DC_OUT 11 10 6 5 4 9 8 7 3 2 1 R19 100K 5% 2 3 Q2 MMBT2222A C27 1 + 2 R39 100K Pot 1 56uF/35V Low ESR 3 C26 68u 10V B +3.3V +5V U12 RC1117S25T +5V VIN ADJ VOUT +2.5V C28 0.1u 3 +5V C30 0.1u 2 3 VIN ADJ U13 LT1117CM-3.3 VOUT 2 LCDVCC 1 A 1 Figure 10-3: S1D13A04B00C Schematics (3 of 6) + C29 68u 10V + C31 68u 10V 12 23 3 2 1 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 5 4 3 + S1D13A04 X37A-G-004-02 5 4 3 2 1 U9 RD-0412 D D L1 VDDH + C22 R21 470K 5% C21 0.1u 68u 10V JP5 HEADER 3 1uH +5V + U11 2 4 R22 200K Pot C23 10uF/63V Low ESR + C24 10uF/63V Low ESR + C25 10uF/63V Low ESR C32 0.1u 1 GPIO0 +3.3V R23 2 For U11 R18 1K 5% +5V R20 100K 5% VLCD B JP3 HEADER 3 5.0V LCD Panels 3.3V LCD Panels A Title S5U13A04B00C Rev. 1.0 - Power Supplies Size B Date: 2 Document Number 1 Rev 1.0 3 of 6 Epson Research and Development Vancouver Design Center 5 4 3 2 1 FPDAT[17:0] 1 FPDAT[17:0] U14 BFPDAT16 BFPDAT17 H1 BFPDAT[17:0] Epson Research and Development Vancouver Design Center D FPDAT0 FPDAT1 FPDAT2 FPDAT3 FPDAT4 FPDAT5 FPDAT6 FPDAT7 2 4 6 8 11 13 15 17 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 1G 2G 74HCT244 C33 0.1u VCC GND 20 10 LCDVCC 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 1 19 18 16 14 12 9 7 5 3 BFPDAT0 BFPDAT1 BFPDAT2 BFPDAT3 BFPDAT4 BFPDAT5 BFPDAT6 BFPDAT7 BFPDAT0 BFPDAT1 BFPDAT2 BFPDAT3 BFPDAT4 BFPDAT5 BFPDAT6 BFPDAT7 BFPDAT8 BFPDAT9 BFPDAT10 BFPDAT11 BFPDAT12 BFPDAT13 BFPDAT14 BFPDAT15 VLCD LCDVCC +12V VDDH D 1 GPIO0 U15 JP4 HEADER 20X2 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 +3.3V 14 HEADER 3 U4E 11 1 19 74AHC04 7 74HCT244 1G 2G C34 0.1u VCC GND LCDVCC 20 10 10 1 2 3 3 A 3 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 FPDAT8 FPDAT9 FPDAT10 FPDAT11 FPDAT12 FPDAT13 FPDAT14 FPDAT15 2 4 6 8 11 13 15 17 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 18 16 14 12 9 7 5 3 BFPDAT8 BFPDAT9 BFPDAT10 BFPDAT11 BFPDAT12 BFPDAT13 BFPDAT14 BFPDAT15 Primary LCD Connector C C U16 FPDAT16 FPDAT17 1 PWMOUT DISPLAY 1 1 1 1 FPFRAME FPLINE DRDY FPSHIFT 1 19 1G 2G 74HCT244 C35 0.1u B 2 4 6 8 11 13 15 17 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 VCC GND 20 10 LCDVCC 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 18 16 14 12 9 7 5 3 BFPDAT16 BFPDAT17 B USBPUP 1 +3.3V D1 BAV99 2 1 R27 1.5K 1% R28 150K 1% R29 301K 1% GPIO4 GPIO5 1 USBDETECT H2 J1 R24 20 1% 1 2 3 4 VBus DM DP GND USB B Connector Figure 10-4: S1D13A04B00C Schematics (4 of 6) USBDM GPIO6 GPIO7 1 1 USBDP R25 20 1% R26 301K 1% 1 BAV99 D2 +3.3V 2 1 1,3 1,3 1,3 1 1 1 1 GPIO0 GPIO1 GPIO2 GPIO3 GPIO4 GPIO5 GPIO6 GPO0 1 3 5 7 9 11 13 15 2 4 6 8 10 12 14 16 HEADER 8X2 A L2 Ferrite Extended LCD Connector Title S5U13A04B00C Rev. 1.0 - LCD/USB Connectors Size B Date: 5 4 3 2 Document Number 1 Rev 1.0 4 of 6 S1D13A04 X37A-G-004-02 Page 29 Page 30 AB13 AB12 AB11 AB10 AB9 AB8 AB7 AB6 AB5 AB4 AB3 AB2 AB1 AB0 DCLK DATA DB15 DB14 DB13 DB12 DB11 DB10 144 143 142 141 140 139 138 137 136 135 134 133 132 131 130 129 128 127 126 125 124 123 122 121 120 119 118 117 116 115 114 113 112 111 110 109 IO144 IO143 IO142 IO141 IO140 IO139 IO138 IO137 IO136 IO135 IO134 IO133 IO132 IO131 IO130 IO129 DCLK Vccio GND DATA IO124 IO123 IO122 IO121 IO120 IO119 IO118 IO117 IO116 IO115 IO114 IO113 IO112 IO111 IO110 IO109 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 IO37 IO38 IO39 IO40 IO41 IO42 IO43 IO44 IO45 IO46 IO47 IO48 IO49 IO50 IO51 IO52 nCONFIG GND Vccio nSTATUS IO57 IO58 IO59 IO60 IO61 IO62 IO63 IO64 IO65 IO66 IO67 IO68 IO69 IO70 IO71 IO72 AD25 AD24 AD23 AD22 AD21 AD20 AD19 AD18 AD17 AD16 AD15 AD14 AD13 AD12 AD11 AD10 AD9 Figure 10-5: S1D13A04B00C Schematics (5 of 6) 5 AD[31:0] AD[31:0] R38 1K 5% nSTATUS AD8 S1D13A04 X37A-G-004-02 A B C D E 4 4 +3.3V AB[17:0] AB[17:0] 1,5 1,5 DB[15:0] +3.3V R30 100K 5% EPF6016TC144-2 R31 15K 5% DB9 DB8 DB7 CONF_DONE R32 1K 5% R33 1K 5% +5V +5V +5V DB[15:0] BUSCLK RD# BS# RD/WR# WE1# M/R# CS# WAIT# WE0# RESET# 1,2,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 1,5 U17 AB14 AB15 AB16 U18 +5V +5V DATA DCLK OE nCS VCC VCC nCASC GND EPC1441PC8 +5V AB17 DB6 DB5 DB4 DB3 DB2 DB1 DB0 3 DATA DCLK nSTATUS CONF_DONE 1 2 3 4 8 7 6 5 C36 0.22u 3 FPGA configuration EPROM SW2 1 2 3 4 SW DIP-4 R34 15K 5% R35 15K 5% R36 15K 5% R37 15K 5% 8 7 6 5 +5V +5V +5V +5V 5 CLK 5 AD31 AD30 AD29 RST# AD0 AD1 AD2 AD3 AD4 Do Not Populate 2 +5V AD5 AD6 AD7 +5V +5V +5V 2 AD28 AD27 AD26 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 IO1 IO2 IO3 nCE GND Vccint Vccio IO8 IO9 IO10 IO11 IO12 IO13 IO14 IO15 IO16 I17 GND Vccio I20 IO21 IO22 IO23 IO24 IO25 IO26 IO27 IO28 IO29 GND Vccint Vccio MSEL IO34 IO35 IO36 C37 0.22u IO108 IO107 IO106 CONF_DONE Vccio Vccint GND IO101 IO100 IO99 IO98 IO97 IO96 IO95 IO94 IO93 I92 Vccio GND I89 IO88 IO87 IO86 IO85 IO84 IO83 IO82 IO81 IO80 IO79 Vccio Vccint GND IO75 IO74 IO73 108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73 C38 0.22u C39 0.22u C40 0.22u Place one on each +5V Power Pin of U18 +3.3V +3.3V +3.3V +3.3V Place one on each +3.3V Power Pin of U18 C41 0.22u +5V C42 0.22u C43 0.22u C44 0.22u 1 nCONFIG 1 1 Title S5U13A04B00C - FPGA Size B Date: A B C D 5 5 5 5 5 5 5 5 5 5 5 5 5 C/BE3# IDSEL C/BE2# FRAME# IRDY# TRDY# DEVSEL# STOP# PERR# SERR# PAR C/BE1# C/BE0# Document Number E Rev 1.0 5 of 6 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center 5 4 3 2 1 6 1,6 DB[15:0] +12V +5V +12V PCIA1 PCIB1 DB0 DB2 DB4 DB6 DB8 DB10 DB12 DB14 1,6 RESET# H3 +5V +12V AD[31:0] AD[31:0] DB[15:0] Epson Research and Development Vancouver Design Center D DB1 DB3 +12V DB5 DB7 D + DB9 DB11 DB13 DB15 PCI_IRQ 1 2 3 4 5 6 7 8 9 10 11 TRST# +12V TMS TDI +5V INTA# INTC# +5V RESERVED +VI/O RESERVED -12V TCK GND TDO +5V +5V INTB# INTD# PRSNT#1 RESERVED PRSNT#2 1 2 3 4 5 6 7 8 9 10 11 C50 33u 20V 6 CLK 6 RST# 1,6 1,6 1,6 WE0# CS# WE1# 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 HEADER 17X2 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 WAIT# M/R# +3.3V 1,6 1,6 10 14 14 1 14 4 14 U4F 1,6 IRQ 13 12 +3.3V 2 3 PCI_IRQ +3.3V 5 6 +3.3V 9 8 +3.3V 12 11 52 53 54 55 56 57 58 59 60 61 62 AD5 AD3 AD1 C/BE0# +3.3V AD6 AD4 GND AD2 AD0 +VI/O REQ64# +5V +5V PCI-A +5V +5V PCI-B +12V +3.3V AD8 AD7 +3.3V AD5 AD3 GND AD1 +VI/O ACK64# +5V +5V 52 53 54 55 56 57 58 59 60 61 62 7 7 7 7 U19A 74HCT125/SO 74AHC04 U19B 74HCT125/SO U19C 74HCT125/SO 7 Figure 10-6: S1D13A04B00C Schematics (6 of 6) AD30 AD31 AD29 AB[17:0] 1,6 AB[17:0] AD27 AD25 C/BE3# 6 AD28 AD26 AD24 AD23 AD21 AD19 AD17 C/BE2# IRDY# DEVSEL# 6 6 6 14 + C45 68u 10V 68u 10V + C46 + C47 33u 20V C48 0.1u A A Place close to PCIB pin 5 & 6 Place close to PCIB pin 61 & 62 Place close to PCIA pin 2 For U19 Title S5U13A04B00C Rev. 1.0 - Host Bus Connectors Size B Date: Document Number 3 2 13 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 C C +5V H4 +5V 6 AD22 AD20 AD18 AD16 IDSEL AB0 AB2 AB4 AB6 AB8 AB10 AB12 AB14 AB16 AB1 AB3 AB5 AB7 AB9 AB11 AB13 AB15 AB17 +5V + C49 68u 10V 6 FRAME# 6 TRDY# 6 PERR# 6 6 6 SERR# AD14 AD12 AD10 C/BE1# STOP# 1,6 1,2,6 RD/WR# BUSCLK BS# RD# HEADER 17X2 1,6 1,6 6 AD15 AD13 AD11 AD9 PAR 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 B 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 RESERVED RST# +VI/O GNT# GND RESERVED AD30 +3.3V AD28 AD26 GND AD24 IDSEL +3.3V AD22 AD20 GND AD18 AD16 +3.3V FRAME# GND TRDY# GND STOP# +3.3V SDONE SBO# GND PAR AD15 +3.3V AD13 AD11 GND AD9 RESERVED GND CLK GND REQ# +VI/O AD31 AD29 GND AD27 AD25 +3.3V C/BE3# AD23 GND AD21 AD19 +3.3V AD17 C/BE2# GND IRDY# +3.3V DEVSEL# GND LOCK# PERR# +3.3V SERR# 3.3V C/BE1# AD14 GND AD12 AD10 GND 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 B 6 AD6 AD4 AD2 AD0 C/BE0# AD8 AD7 +3.3V U19D 74HCT125/SO Rev 1.0 Sheet 1 6 of 6 5 4 S1D13A04 X37A-G-004-02 Page 31 Page 32 Epson Research and Development Vancouver Design Center 11 Board Layout Figure 11-1: S5U13A04B00C Board Layout S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 Epson Research and Development Vancouver Design Center Page 33 12 Sales and Technical Support 12.1 Epson Companion Chips (S1D13A04) Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp/ North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com/ Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk// Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de/ S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 X37A-G-004-02 Page 34 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-004-02 S5U13A04B00C Rev. 1.0 Evaluation Board User Manual Issue Date: 02/01/28 S1D13A04 LCD/USB Companion Chip Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Document Number: X37A-G-002-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All other trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-002-01 Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 3 Table of Contents 1 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Interfacing to the TMPR3905/12 . . . . . . . . . . 2.1 The Toshiba TMPR3905/12 System Bus . . . . . 2.1.1 Overview . . . . . . . . . . . . . . . . . . . 2.1.2 Card Access Cycles . . . . . . . . . . . . . . ... .. ... ... . . . . ...... ..... ....... ....... . . . . ....... ...... ........ ........ .8 .8 .8 .8 3 S1D13A04 Host Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.1 Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . 10 3.2 Host Bus Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . 11 Toshiba TMPR3905/12 to S1D13A04 Interface 4.1 Hardware Description . . . . . . . . . . 4.2 S1D13A04 Hardware Configuration . . . . 4.3 Memory Mapping and Aliasing . . . . . . . . . . . . . . ... .. .. .. . . . . . . . . . . . . ... .. .. .. . . . . . . . . . . . . ... .. .. .. . . . . . . . . . . . . 12 12 14 14 4 5 6 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7.1 EPSON LCD/USB Companion Chips (S1D13A04) . . . . . . . . . . . . . . . 17 7.2 Toshiba MIPS TMPR3905/12 Processor . . . . . . . . . . . . . . . . . . . . 17 7 Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-002-01 Page 4 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-002-01 Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 5 List of Tables Table 3-1: Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Table 4-1: Summary of Power-On/Reset Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 List of Figures Figure 2-1: Toshiba 3905/12 PC Card Memory/Attribute Cycle . . . . . . . . . . . . . . . . . . . . 9 Figure 2-2: Toshiba 3905/12 PC Card IO Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 4-1: S1D13A04 to TMPR3905/12 Direct Connection . . . . . . . . . . . . . . . . . . . . . 12 Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-002-01 Page 6 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-002-01 Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 7 1 Introduction This application note describes the hardware and software environment necessary to provide an interface between the S1D13A04 USB/LCD Companion Chip and the Toshiba MIPS TMPR3905/3912 processors. The designs described in this document are presented only as examples of how such interfaces might be implemented. This application note is updated as appropriate. Please check the Epson Research and Development website at www.erd.epson.com for the latest revision of this document before beginning any development. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-002-01 Page 8 Epson Research and Development Vancouver Design Center 2 Interfacing to the TMPR3905/12 2.1 The Toshiba TMPR3905/12 System Bus The TMPR39XX family of processors features a high-speed system bus typical of modern MIPS RISC microprocessors. This section provides an overview of the operation of the CPU bus in order to establish interface requirements. 2.1.1 Overview The TMPR3905/12 is a highly integrated controller developed for handheld products. The microprocessor is based on the R3900 MIPS RISC processor core. The TMPR3905/12 implements an external 26-bit address bus and a 32-bit data bus allowing it to communicate with its many peripheral units. The address bus is multiplexed (A[12:0]) using an address latch signal (ALE) which controls the driving of the address onto the address bus. The full 26-bit address bus (A[25:0]) is generated to devices not capable of receiving a multiplexed address, using external latches (controlled by ALE). The TMPR3905/12 provides two, revision 2.01 compliant, PC Card slots. The 16-bit PC Card slots provide a 26-bit multiplexed address and additional control signals which allow access to three 64M byte address ranges: IO, memory, and attribute space. The signal CARDREG* selects memory space when high and attribute or IO space when low. Memory and attribute space are accessed using the write and read enable signals (WE* and RD*). When CARDREG* is low, card IO space is accessed using separate write (CARDIOWR*) and read (CARDIORD*) control signals. 2.1.2 Card Access Cycles A data transfer is initiated when the address is placed on the PC Card bus and one, or both, of the card enable signals (CARD1CSL* and CARD1CSH*) are driven low. CARDREG* is inactive for memory and IO cycles. If only CARD1CSL* is driven low, 8-bit data transfers are enabled and A0 specifies whether the even or odd data byte appears on the PC Card data bus lines D[7:0]. If only CARD1CSH* is driven low, an odd byte transfer occurs on PC Card data lines D[15:8]. If both CARD1CSL* and CARD1CSH* are driven low, a 16-bit word transfer takes place on D[15:0]. During a read cycle, either RD* or CARDIORD* is driven low depending on whether a memory or IO cycle is specified. A write cycle is specified by driving WE* (memory cycle) or CARDIOWR* (IO cycle) low. The cycle can be lengthened by driving CARD1WAIT* low for the time required to complete the cycle. S1D13A04 X37A-G-002-01 Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 9 Figure 2-1: "Toshiba 3905/12 PC Card Memory/Attribute Cycle," illustrates a typical memory/attribute cycle on the Toshiba 3905/12 PC Card bus. A[25:0] CARDREG* ALE D[31:16] CARD1CSL* CARD1CSH* RD* WE* CARD1WAIT* Figure 2-1: Toshiba 3905/12 PC Card Memory/Attribute Cycle Figure 2-2: "Toshiba 3905/12 PC Card IO Cycle," illustrates a typical IO cycle on the Toshiba 3905/12 PC Card bus. A[25:0] ALE D[31:16] CARD1CSL* CARD1CSH* CARDIORD* CARDIOWR* CARD1WAIT* CARDREG* Figure 2-2: Toshiba 3905/12 PC Card IO Cycle Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-002-01 Page 10 Epson Research and Development Vancouver Design Center 3 S1D13A04 Host Bus Interface The S1D13A04 directly supports multiple processors. The S1D13A04 implements a 16-bit Generic #2 Host Bus Interface which is most suitable for connection to the Toshiba TMPR3905/12 microprocessor. The Generic #2 Host Bus Interface is selected by the S1D13A04 on the rising edge of RESET#. After releasing reset the bus interface signals assume their selected configuration. For details on the S1D13A04 configuration, see Section 4.2, "S1D13A04 Hardware Configuration" on page 14. 3.1 Host Bus Interface Pin Mapping The following table shows the functions of each Host Bus Interface signal. Table 3-1: Host Bus Interface Pin Mapping S1D13A04 Pin Names AB[17:0] DB[15:8] DB[7:0] WE1# CS# M/R# CLKI BS# RD/WR# RD# WE0# WAIT# RESET# Toshiba TMPR3905/12 External Decode D[23:16] D[31:24] External Decode External Decode External Decode DCLKOUT Connect to IOVDD from the S1D13A04 Connect to IOVDD from the S1D13A04 CARDIORD* CARDIOWR* CARD1WAIT* system RESET S1D13A04 X37A-G-002-01 Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 11 3.2 Host Bus Interface Signals The Host Bus Interface requires the following signals. * CLKI is a clock input required by the S1D13A04 Host Bus Interface as a source for its internal bus and memory clocks. This clock is typically driven by the host CPU system clock. For example, DCLKOUT from the Toshiba TMPR3905/12. * The address inputs AB[12:0] are connected directly to the TMPR3905/12 address bus. Since the TMPR3905/12 has a multiplexed address bus, the other address inputs A[17:13] must be generated using an external latch controlled by the address latch enable signal (ALE). The low data byte on the TMPR3905/12 data bus for 16-bit ports is D[31:24] and connects to the S1D13A04 low data byte, D[7:0]. The high data byte on the TMPR3905/12 data bus for 16-bit ports is D[23:16] and connects to the S1D13A04 high data byte, D[15:0]. The hardware engineer must ensure that CNF4 selects the proper endian mode upon reset. * Chip Select (CS#) is driven by external decoding circuitry to select the S1D13A04. * M/R# (memory/register) selects between memory or register accesses. This signal is generated by the external address decode circuitry. For this example, M/R# is connected to address line A18, allowing system address A18 to select between memory or register accesses. * WE1# is connected to CARD1CSH* and is the high byte enable for both read and write cycles. * WE0# is connected to CARDIOWR* (the write enable signal) and must be driven low when the Toshiba TMPR3905/12 is writing data to the S1D13A04. * RD# is connected to CARDIORD* (the read enable signal) and must be driven low when the Toshiba TMPR3905/12 is reading data from the S1D13A04. * WAIT# connects to CARD1WAIT* and is a signal which is output from the S1D13A04 to the TMPR3905/12 that indicates when data is ready (read cycle) or accepted (write cycle) on the host bus. Since host CPU accesses to the S1D13A04 may occur asynchronously to the display update, it is possible that contention may occur in accessing the S1D13A04 internal registers and/or display buffer. The WAIT# line resolves these contentions by forcing the host to wait until the resource arbitration is complete. * The Bus Status (BS#) and Read/Write (RD/WR#) signals are not used in this implementation of the Toshiba TMPR3905/12 using the Generic #2 Host Bus Interface. These pins must be tied high (connected to IO VDD). Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-002-01 Page 12 Epson Research and Development Vancouver Design Center 4 Toshiba TMPR3905/12 to S1D13A04 Interface 4.1 Hardware Description In this implementation, the S1D13A04 occupies the TMPR3905/12 PC Card slot #1 IO address space. IO address space closely matches the timing parameters for the S1D13A04 Generic #2 Host Bus Interface. The address bus of the TMPR3905/12 PC Card interface is multiplexed and must be demultiplexed using an advanced CMOS latch (e.g., 74AHC373). BS# (bus start) and RD/WR# are not used in this implementation and should be tied high (connected to IO VDD). A pull-up resistor is attached to WAIT# to speed up its rise time when terminating a cycle. The following diagram demonstrates a typical implementation of the TMPR3905/12 to S1D13A04 interface. S1D13A04 TMPR3905/12 CARDIORD* CARDIOWR* CARD1CSL* CARD1CSH* RD# WE0# M/R# IO VDD WE1# BS# A18 ENDIAN Latch System RESET RD/WR# RESET# CS# AB[17:13] AB[12:0] DB[7:0] DB[15:8] ALE A[12:0] D[31:24] D[23:16] HIOVDD pull-up CARD1WAIT* DCLKOUT Clock divider WAIT# See text ...or... Oscillator CLKI2 CLKI Note: When connecting the S1D13A04 RESET# pin, the system designer should be aware of all conditions that may reset the S1D13A04 (e.g. CPU reset can be asserted during wake-up from power-down modes, or during debug states). Figure 4-1: S1D13A04 to TMPR3905/12 Direct Connection S1D13A04 X37A-G-002-01 Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 13 The Generic #2 Host Bus Interface control signals of the S1D13A04 are asynchronous with respect to the S1D13A04 bus clock. This gives the system designer full flexibility to choose the appropriate source (or sources) for CLKI and CLKI2. The choice of whether both clocks should be the same, and whether to use DCLKOUT (divided) as clock source, should be based on the desired: * pixel and frame rates. * power budget. * part count. * maximum S1D13A04 clock frequencies. The S1D13A04 also has internal clock dividers providing additional flexibility. Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-002-01 Page 14 Epson Research and Development Vancouver Design Center 4.2 S1D13A04 Hardware Configuration The S1D13A04 latches CNF6 through CNF0 to allow selection of the bus mode and other configuration data on the rising edge of RESET#. For details on configuration, refer to the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. The table below shows the configuration settings important to the Generic #2 host bus interface used by the Toshiba TMPR3905/12. Table 4-1: Summary of Power-On/Reset Options S1D13A04 Configuration Input CNF4, CNF[2:0] CNF3 CNF5 CNF6 Power-On/Reset State 1 (connected to IO VDD) Select host bus interface as follows: CNF4 0 CNF2 1 CNF1 0 CNF0 0 Host Bus Generic #2, Little Endian WAIT# is active low CLKI to BCLK divide ratio 1:1 0 (connected to VSS) Reserved. Must be set to 1. WAIT# is active high CLKI to BCLK divide ratio 2:1 configuration for Toshiba TMPR3905/3912 microprocessor 4.3 Memory Mapping and Aliasing In this implementation the TMPR3905/12 control signal CARDREG* is ignored. This means that the S1D13A04 takes up the entire PC Card slot 1. The S1D13A04 is a memory mapped device and uses two 256K byte blocks which are selected using A18 from the TMPR3905/12 (A18 is connected to the S1D13A04 M/R# pin). The internal registers occupy the first 256K byte block and the 160K byte display buffer occupies the second 256K byte block. The registers occupy the range 0h through 3FFFFh while the on-chip display memory occupies the range 40000h through 68000h. Demultiplexed address lines A[25:19] are ignored. Therefore, the S1D13A04 is aliased at 256K byte intervals over the 64M byte PC Card slot #1 memory space. Note If aliasing is undesirable, additional decoding circuitry must be added. S1D13A04 X37A-G-002-01 Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 15 5 Software Test utilities and display drivers are available for the S1D13A04. Full source code is available for both the test utilities and the drivers. The test utilities are configurable for different panel types using a program called 13A04CFG (see document number X37A-B-001-xx), or by directly modifying the source. The display drivers can be customized by the OEM for different panel types, resolutions and color depths only by modifying the source. The S1D13A04 test utilities and display drivers are available from your sales support contact (see Section 7, "Sales and Technical Support") or www.erd.epson.com. Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-002-01 Page 16 Epson Research and Development Vancouver Design Center 6 References 6.1 Documents * Toshiba America Electrical Components, Inc., TMPR3905/12 Specification. * Epson Research and Development, Inc., S1D13A04 Hardware Functional Specification, Document Number X37A-A-001-xx. * Epson Research and Development, Inc., S5U13A04B00C Rev. 1.0 ISA Bus Evaluation Board User Manual, Document Number X37A-G-004-xx. * Epson Research and Development, Inc., S1D13A04 Programming Notes and Examples, Document Number X37A-G-003-xx. 6.2 Document Sources * Toshiba America Electrical Components Website: www.toshiba.com/taec. * Epson Research and Development Website: www.erd.epson.com. S1D13A04 X37A-G-002-01 Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 17 7 Sales and Technical Support 7.1 EPSON LCD/USB Companion Chips (S1D13A04) Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk/ Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de 7.2 Toshiba MIPS TMPR3905/12 Processor http://www.toshiba.com/taec/nonflash/indexproducts.html Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-002-01 Page 18 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-002-01 Interfacing to the Toshiba MIPS TMPR3905/3912 Microprocessors Issue Date: 01/10/12 S1D13A04 LCD/USB Companion Chip Interfacing to the PC Card Bus Document Number: X37A-G-005-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All other trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-005-01 Interfacing to the PC Card Bus Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 3 Table of Contents 1 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Interfacing to the PC Card Bus 2.1 The PC Card System Bus . . 2.1.1 PC Card Overview . . 2.1.2 Memory Access Cycles .. .. ... ... . . . . ... .. ... ... .... .... ..... ..... ... .. ... ... . . . . ...... ..... ....... ....... . . . . ... .. ... ... .... .... ..... ..... .8 .8 .8 .8 3 S1D13A04 Host Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.1 Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . 10 3.2 Host Bus Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . 11 PC Card to S1D13A04 Interface . . . 4.1 Hardware Connections . . . . . . 4.2 S1D13A04 Hardware Configuration 4.3 Register/Memory Mapping . . . . . . . . ... .. .. .. . . . . . . . . . . . . ... .. .. .. . . . . . . . . . . . . ... .. .. .. . . . . . . . . . . . . ... .. .. .. . . . . . . . . . . . . 12 12 13 13 4 5 6 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 7.1 EPSON LCD/USB Companion Chips (S1D13A04) . . . . . . . . . . . . . . . 16 7.2 PC Card Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 7 Interfacing to the PC Card Bus Issue Date: 01/10/12 S1D13A04 X37A-G-005-01 Page 4 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-005-01 Interfacing to the PC Card Bus Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 5 List of Tables Table 3-1: Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Table 4-1: Summary of Power-On/Reset Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 List of Figures Figure 2-1: PC Card Read Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 2-2: PC Card Write Cycle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 4-1: Typical Implementation of PC Card to S1D13A04 Interface . . . . . . . . . . . . . . . 12 Interfacing to the PC Card Bus Issue Date: 01/10/12 S1D13A04 X37A-G-005-01 Page 6 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-005-01 Interfacing to the PC Card Bus Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 7 1 Introduction This application note describes the hardware and software environment required to interface the S1D13A04 LCD/USB Companion Chip and the PC Card (PCMCIA) bus. The designs described in this document are presented only as examples of how such interfaces might be implemented. This application note is updated as appropriate. Please check the Epson Research and Development website at www.erd.epson.com for the latest revision of this document before beginning any development. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. Interfacing to the PC Card Bus Issue Date: 01/10/12 S1D13A04 X37A-G-005-01 Page 8 Epson Research and Development Vancouver Design Center 2 Interfacing to the PC Card Bus 2.1 The PC Card System Bus PC Card technology has gained wide acceptance in the mobile computing field as well as in other markets due to its portability and ruggedness. This section is an overview of the operation of the 16-bit PC Card interface conforming to the PCMCIA 2.0/JEIDA 4.1 Standard (or later). 2.1.1 PC Card Overview The 16-bit PC Card provides a 26-bit address bus and additional control lines which allow access to three 64M byte address ranges. These ranges are used for common memory space, IO space, and attribute memory space. Common memory may be accessed by a host system for memory read and write operations. Attribute memory is used for defining card specific information such as configuration registers, card capabilities, and card use. IO space maintains software and hardware compatibility with hosts such as the Intel x86 architecture, which address peripherals independently from memory space. Bit notation follows the convention used by most microprocessors, the high bit is the most significant. Therefore, signals A25 and D15 are the most significant bits for the address and data bus respectively. Support is provided for on-chip DMA controllers. To find further information on these topics, refer to Section 6, "References" on page 15. PC Card bus signals are asynchronous to the host CPU bus signals. Bus cycles are started with the assertion of either the -CE1 and/or the -CE2 card enable signals. The cycle ends once these signals are de-asserted. Bus cycles can be lengthened using the -WAIT signal. Note The PCMCIA 2.0/JEIDA 4.1 (and later) PC Card Standard support the two signals -WAIT and RESET which are not supported in earlier versions of the standard. The -WAIT signal allows for asynchronous data transfers for memory, attribute, and IO access cycles. The RESET signal allows resetting of the card configuration by the reset line of the host CPU. 2.1.2 Memory Access Cycles A data transfer is initiated when the memory address is placed on the PC Card bus and one, or both, of the card enable signals (-CE1 and -CE2) are driven low. -REG must be kept inactive. If only -CE1 is driven low, 8-bit data transfers are enabled and A0 specifies whether the even or odd data byte appears on data bus lines D[7:0]. If both -CE1 and -CE2 are driven low, a 16-bit word transfer takes place. If only -CE2 is driven low, an odd byte transfer occurs on data lines D[15:8]. S1D13A04 X37A-G-005-01 Interfacing to the PC Card Bus Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 9 During a read cycle, -OE (output enable) is driven low. A write cycle is specified by driving -OE high and driving the write enable signal (-WE) low. The cycle can be lengthened by driving -WAIT low for the time needed to complete the cycle. Figure 2-1: illustrates a typical memory access read cycle on the PC Card bus. A[25:0] -REG ADDRESS VALID -CE1 -CE2 -OE -WAIT D[15:0] Hi-Z DATA VALID Hi-Z Transfer Start Transfer Complete Figure 2-1: PC Card Read Cycle Figure 2-2: illustrates a typical memory access write cycle on the PC Card bus. A[25:0] -REG ADDRESS VALID -CE1 -CE2 -OE -WE -WAIT D[15:0] Hi-Z DATA VALID Hi-Z Transfer Start Transfer Complete Figure 2-2: PC Card Write Cycle Interfacing to the PC Card Bus Issue Date: 01/10/12 S1D13A04 X37A-G-005-01 Page 10 Epson Research and Development Vancouver Design Center 3 S1D13A04 Host Bus Interface The S1D13A04 directly supports multiple processors. The S1D13A04 implements a 16-bit Generic #2 Host Bus Interface which is most suitable for direct connection to the PC Card bus. Generic #2 supports an external Chip Select, shared Read/Write Enable for high byte, and individual Read/Write Enable for low byte. The Generic #2 Host Bus Interface is selected by the S1D13A04 on the rising edge of RESET#. After RESET# is released, the bus interface signals assume their selected configuration. For details on the S1D13A04 configuration, see Section 4.2, "S1D13A04 Hardware Configuration" on page 13. 3.1 Host Bus Interface Pin Mapping The following table shows the functions of each Host Bus Interface signal. Table 3-1: Host Bus Interface Pin Mapping S1D13A04 Pin Names AB[17:0] DB[15:0] WE1# CS# M/R# CLKI BS# RD/WR# RD# WE0# WAIT# RESET# PC Card (PCMCIA) A[17:0] D[15:0] -CE2 External Decode A18 see note Connect to IOVDD from the S1D13A04 Connect to IOVDD from the S1D13A04 -OE -WE -WAIT Inverted RESET Note Although a clock is not directly supplied by the PC Card interface, one is required by the S1D13A04 Generic #2 Host Bus Interface. For an example of how this can be accomplished see the discussion on CLKI in Section 3.2, "Host Bus Interface Signals" on page 11. S1D13A04 X37A-G-005-01 Interfacing to the PC Card Bus Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 11 3.2 Host Bus Interface Signals The S1D13A04 Generic #2 Host Bus Interface requires the following signals from the PC Card bus. * CLKI is a clock input which is required by the S1D13A04 Host Bus Interface as a source for its internal bus and memory clocks. This clock is typically driven by the host CPU system clock. Since the PC Card signalling is independent of any clock, CLKI can come from any oscillator already implemented. For example, the source for the CLKI2 input of the S1D13A04 may be used. * The address inputs AB[17:0], and the data bus DB[15:0], connect directly to the PC Card address (A[17:0]) and data bus (D[15:0]), respectively. CNF4 must be set to select little endian mode. * Chip Select (CS#) is driven by decoding the high-order address lines to select the proper register and memory address space. * M/R# (memory/register) selects between memory or register accesses. This signal is generated by the external address decode circuitry. For this example, M/R# is connected to address line A18, allowing system address A18 to select between memory or register accesses. * WE1# connects to -CE2 (the high byte chip select signal from the PC Card interface) which in conjunction with address bit 0 allows byte steering of read and write operations. * WE0# connects to -WE (the write enable signal form the PC Card bus) and must be driven low when the PC Card bus is writing data to the S1D13A04. * RD# connects to -OE (the read enable signal from the PC Card bus) and must be driven low when the PC Card bus is reading data from the S1D13A04. * WAIT# is a signal output from the S1D13A04 that indicates the PC Card bus must wait until data is ready (read cycle) or accepted (write cycle) on the host bus. Since PC Card bus accesses to the S1D13A04 may occur asynchronously to the display update, it is possible that contention may occur in accessing the S1D13A04 internal registers and/or display buffer. The WAIT# line resolves these contentions by forcing the host to wait until the resource arbitration is complete. * The Bus Status (BS#) and Read/Write (RD/WR#) signals are not used in this implementation of the PC Card bus using the Generic #2 Host Bus Interface. These pins must be tied high (connected to IO VDD). * The RESET# (active low) input of the S1D13A04 may be connected to the PC Card RESET (active high) using an inverter. Interfacing to the PC Card Bus Issue Date: 01/10/12 S1D13A04 X37A-G-005-01 Page 12 Epson Research and Development Vancouver Design Center 4 PC Card to S1D13A04 Interface 4.1 Hardware Connections The S1D13A04 is interfaced to the PC Card bus with a minimal amount of glue logic. In this implementation, the address inputs (AB[17:0]) and data bus (DB[15:0] connect directly to the CPU address (A[17:0]) and data bus (D[15:0]). The PC Card interface does not provide a bus clock, so one must be supplied for the S1D13A04. Since the bus clock frequency is not critical, nor does it have to be synchronous to the bus signals, it may be the same as CLKI2. BS# (bus start) and RD/WR# are not used by the Generic #2 Host Bus Interface and should be tied high (connected to IO VDD). The following diagram shows a typical implementation of the PC Card to S1D13A04 interface. PC Card Bus -OE -WE A18 -CE1 -CE2 RESET IO VDD S1D13A04 RD# WE0# M/R# WE1# RESET# RD/WR# BS# CS# A[17:0] D[15:0] 15K pull-up AB[17:0] DB[15:0] WAIT# CLKI Oscillator CLKI2 -WAIT Note: When connecting the S1D13A04 RESET# pin, the system designer should be aware of all conditions that may reset the S1D13A04 (e.g. CPU reset can be asserted during wake-up from power-down modes, or during debug states). Figure 4-1: Typical Implementation of PC Card to S1D13A04 Interface S1D13A04 X37A-G-005-01 Interfacing to the PC Card Bus Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 13 4.2 S1D13A04 Hardware Configuration The S1D13A04 uses CNF6 through CNF0 to allow selection of the bus mode and other configuration data on the rising edge of RESET#. For details on configuration, refer to the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. The following table shows the configuration required for this implementation of a S1D13A04 to PC Card bus interface. Table 4-1: Summary of Power-On/Reset Options S1D13A04 Configuration Input CNF4, CNF[2:0] CNF3 CNF5 CNF6 Power-On/Reset State 1 (connected to IO VDD) Select host bus interface as follows: CNF4 0 CNF2 1 CNF1 0 CNF0 0 Host Bus Generic #2, Little Endian WAIT# is active low CLKI to BCLK divide ratio 1:1 0 (connected to VSS) Reserved. Must be set to 1. WAIT# is active high CLKI to BCLK divide ratio 2:1 configuration for PC Card bus 4.3 Register/Memory Mapping The S1D13A04 is a memory mapped device. The S1D13A04 uses two 256K byte blocks which are selected using A18 from the PC Card bus (A18 is connected to the S1D13A04 M/R# pin). The internal registers occupy the first 256K byte block and the 160K byte display buffer occupies the second 256K byte block. The PC Card socket provides 64M bytes of memory address space. However, the S1D13A04 only needs a 512K byte block of memory to accommodate its 160K byte display buffer and register set. For this reason, only address bits A[18:0] are used while A[25:19] are ignored. The S1D13A04's memory and registers are aliased every 512K bytes in the 64M byte PC Card memory address space. Note If aliasing is not desirable, the upper addresses must be fully decoded. Interfacing to the PC Card Bus Issue Date: 01/10/12 S1D13A04 X37A-G-005-01 Page 14 Epson Research and Development Vancouver Design Center 5 Software Test utilities and display drivers are available for the S1D13A04. Full source code is available for both the test utilities and the drivers. The test utilities are configurable for different panel types using a program called 13A04CFG (see document number X37A-B-001-xx), or by directly modifying the source. The display drivers can be customized by the OEM for different panel types, resolutions and color depths only by modifying the source. The S1D13A04 test utilities and display drivers are available from your sales support contact (see Section 7, "Sales and Technical Support") or www.erd.epson.com. S1D13A04 X37A-G-005-01 Interfacing to the PC Card Bus Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 15 6 References 6.1 Documents * PC Card (PCMCIA) Standard March 1997. * Epson Research and Development, Inc., S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. * Epson Research and Development, Inc., S5U13A04B00C Rev. 1.0 Evaluation Board User Manual, document number X37A-G-004-xx. * Epson Research and Development, Inc., S1D13A04 Programming Notes and Examples, Document Number X37A-G-003-xx. 6.2 Document Sources * PC Card Website: www.pc-card.com. * Epson Research and Development Website: www.erd.epson.com. Interfacing to the PC Card Bus Issue Date: 01/10/12 S1D13A04 X37A-G-005-01 Page 16 Epson Research and Development Vancouver Design Center 7 Sales and Technical Support 7.1 EPSON LCD/USB Companion Chips (S1D13A04) Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk/ Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de 7.2 PC Card Standard PCMCIA (Personal Computer Memory Card International Association) 2635 North First Street, Suite 209 San Jose, CA 95134 Tel: (408) 433-2273 Fax: (408) 433-9558 http://www.pc-card.com S1D13A04 X37A-G-005-01 Interfacing to the PC Card Bus Issue Date: 01/10/12 S1D13A04 LCD/USB Companion Chip Power Consumption Document Number: X37A-G-006-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All other trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-006-01 Power Consumption Issue Date: 01/10/29 Epson Research and Development Vancouver Design Center Page 3 1 S1D13A04 Power Consumption S1D13A04 power consumption is affected by many system design variables. * Input clock frequency (CLKI/CLKI2): the CLKI/CLKI2 frequency determines the LCD frame-rate, CPU performance to memory, and other functions - the higher the input clock frequency, the higher the frame-rate, performance and power consumption. * CPU interface: the S1D13A04 current consumption depends on the BCLK frequency, data width, number of toggling pins, and other factors - the higher the BCLK, the higher the CPU performance and power consumption. * VDD voltage level: the voltage level affects power consumption - the higher the voltage, the higher the consumption. * Display mode: the resolution and color depth affect power consumption - the higher the resolution/color depth, the higher the consumption. * Internal CLK divide: internal registers allow the input clock to be divided before going to the internal logic blocks - the higher the divide, the lower the power consumption. There is a power save mode in the S1D13A04. The power consumption is affected by various system design variables. * Clock states during the power save mode: disabling the clocks during power save mode has substantial power savings. Power Consumption Issue Date: 01/10/29 S1D13A04 X37A-G-006-01 Page 4 Epson Research and Development Vancouver Design Center 1.1 Conditions The following table provides an example of some 320x240 panels and the effects on power consumption of specific environments. The following conditions apply. * All tests had an appropriate LCD panel connected to the LCD outputs of the S1D13A04. * All tests were run with a static full color palette display. * All tests were done using the Generic #1 host bus interface (BCLK = 33MHz). Table 1-1: S1D13A04 Total Power Consumption for 320x240 panels Test Condition All COREVDD = 2.0V and IOVDD = 3.3V Resolution Panel Type Frame Rate 67 67 Color 8-bit Format 2 67 67 Clocks (MHz) CLKI = 6 = BCLK = MCLK CLKI2 = 6 = PCLK USBCLK = 48 CLKI = 6 = BCLK CLKI2 = 6 = PCLK USBCLK = grounded CLKI = 33.3 = MCLK = BCLK CLKI2 = grounded USBCLK = 48, PCLK = MCLK / 4 CLKI = 33.3 = MCLK = BCLK CLKI2 = grounded USBCLK = grounded, PCLK = MCLK / 4 CLKI = 33.3 = MCLK = BCLK CLKI2 = grounded USBCLK = 48, PCLK = MCLK / 4 CLKI = 33.3 = MCLK = BCLK CLKI2 = grounded USBCLK = grounded, PCLK = MCLK / 4 Color Depth 4 8 16 8 Power Consumption (mA) S1D13A04 Active CORE 1.7 2.1 2.4 1.8 IO 0.7 0.7 0.6 0.6 Power Save Mode CORE1 0.7 0.7 0.7 0.4 IO1 0.1 0.1 0.1 0.0 Clocks Removed2 0.1 0.1 0.1 0.1 94 320x240 Color 4-bit 94 8 4.3 1.3 2.3 0.2 0.1 8 4.0 1.2 2.1 0.1 0.1 79 18-bit TFT 79 8 3.7 2.9 2.3 0.2 0.1 8 3.5 2.8 2.1 0.1 0.1 1. The S1D13A04 has Power Save Mode enabled, but the clocks (CLKI, CLKI2 and USBCLK) remain active unless specified otherwise. 2. CLKI, CLKI2, and USBCLK are grounded for the Clocks Removed condition. S1D13A04 X37A-G-006-01 Power Consumption Issue Date: 01/10/29 Epson Research and Development Vancouver Design Center Page 5 The following table provides an example of some 160x160 panels and the effects on power consumption of specific environments. The following conditions apply. * All tests had an appropriate LCD panel connected to the LCD outputs of the S1D13A04. * All tests were run with a static full color palette display, except the test where the 2D BitBLT engine was running. * All tests were done using the Generic #1 host bus interface (BCLK = 33MHz). Table 1-2: S1D13A04 Total Power Consumption for 160x160 panels Test Condition All COREVDD = 2.0V and IOVDD = 3.3V Resolution Panel Type Frame Rate 67 67 18-bit HR-TFT 160x160 18-bit HR-TFT 18-bit HR-TFT 67 67 67 Clocks (MHz) CLKI = 33.3 = MCLK = BCLK CLKI2 = 3 = PCLK USBCLK = 48 CLKI = 33.3 = MCLK = BCLK CLKI2 = 3 = PCLK USBCLK = grounded CLKI = 33.3 = MCLK = BCLK CLKI2 = 3 = PCLK USBCLK = 48, 2D BitBLT engine running3 CLKI = 33.3 = MCLK = BCLK CLKI2 = 3 = PCLK USBCLK = 48, USB is active/running4 Color Depth 4 8 16 16 Power Consumption (mA) S1D13A04 Active CORE 2.5 2.6 2.8 2.6 IO 0.9 1.1 1.1 1.0 Power Save Mode CORE1 2.2 2.2 2.2 4.2 IO1 0.2 0.2 0.2 0.1 Clocks Removed2 0.1 0.1 0.1 0.1 16 12.3 2.4 5 5 5 5 0.1 67 16 12.4 1.6 0.1 1. The S1D13A04 has Power Save Mode enabled, but the clocks (CLKI, CLKI2 and USBCLK) remain active unless specified otherwise. 2. CLKI, CLKI2, and USBCLK are grounded for the Clocks Removed condition. 3. This test has the 2D BitBLT engine performing a Move BitBLT which requires a high-level of CPU activity and a rapidly updating display. 4. This test has the S1D13A04 USB module running a loop-back test. 5. This result is not applicable. See the 16 bpp color depth results for power save mode. Power Consumption Issue Date: 01/10/29 S1D13A04 X37A-G-006-01 Page 6 Epson Research and Development Vancouver Design Center 2 Summary The system design variables in Section 1, "S1D13A04 Power Consumption" and in Table 1-1: "S1D13A04 Total Power Consumption for 320x240 panels" show that S1D13A04 power consumption depends on the specific implementation. Active Mode power consumption depends on the desired CPU performance and LCD frame-rate, whereas power save mode consumption depends on the CPU Interface and Input Clock state. In a typical design environment, the S1D13A04 can be configured to be an extremely power-efficient LCD Controller with high performance and flexibility. S1D13A04 X37A-G-006-01 Power Consumption Issue Date: 01/10/29 S1D13A04 LCD/USB Companion Chip Interfacing to the NEC VR4102 / VR4111 Microprocessors Document Number: X37A-G-007-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All Trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-007-01 Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 3 Table of Contents 1 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Interfacing to the NEC VR4102/VR4111 . . . . . . 2.1 The NEC VR41XX System Bus . . . . . . . . 2.1.1 Overview . . . . . . . . . . . . . . . . . . . 2.1.2 LCD Memory Access Cycles . . . . . . . . . ... .. ... ... . . . . ...... ..... ....... ....... . . . . ....... ...... ........ ........ .8 .8 .8 .9 3 S1D13A04 Host Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.1 Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . 10 3.2 Host Bus Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . 11 VR4102/VR4111 to S1D13A04 Interface 4.1 Hardware Description . . . . . . . 4.2 S1D13A04 Hardware Configuration . 4.3 NEC VR4102/VR4111 Configuration . ... .. .. .. . . . . . . . . . . . . ... .. .. .. . . . . . . . . . . . . ... .. .. .. . . . . . . . . . . . . ... .. .. .. . . . . . . . . . . . . 12 12 13 14 4 5 6 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7.1 EPSON LCD/USB Companion Chips (S1D13A04) . . . . . . . . . . . . . . . 17 7.2 NEC Electronics Inc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7 Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-007-01 Page 4 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-007-01 Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 5 List of Tables Table 3-1: Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Table 4-1: Summary of Power-On/Reset Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 List of Figures Figure 2-1: NEC VR4102/VR4111 Read/Write Cycles . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 4-1: Typical Implementation of VR4102/VR4111 to S1D13A04 Interface . . . . . . . . . . 12 Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-007-01 Page 6 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-007-01 Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 7 1 Introduction This application note describes the hardware and software environment required to interface the S1D13A04 LCD/USB Companion Chip and the NEC VR4102/4111 microprocessor. The NEC VR4102 and VR4111 microprocessors are specifically designed to support an external LCD controller. The designs described in this document are presented only as examples of how such interfaces might be implemented. This application note is updated as appropriate. Please check the Epson Research and Development website at www.erd.epson.com for the latest revision of this document before beginning any development. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-007-01 Page 8 Epson Research and Development Vancouver Design Center 2 Interfacing to the NEC VR4102/VR4111 2.1 The NEC VR41XX System Bus The VR-Series family of microprocessors features a high-speed synchronous system bus typical of modern microprocessors. Designed with external LCD controller support and Windows(R) CE based embedded consumer applications in mind, the VR4102/VR4111 offers a highly integrated solution for portable systems. This section is an overview of the operation of the CPU bus to establish interface requirements. 2.1.1 Overview The NEC VR series microprocessor is designed around the RISC architecture developed by MIPS. The VR4102 microprocessor is designed around the 66MHz VR4100 CPU core and the VR4111 is designed around the 80/100MHz VR4110 core. These microprocessors support 64-bit processing. The CPU communicates with the Bus Control Unit (BCU) through its internal SysAD bus. The BCU in turn communicates with external devices with its ADD and DATA busses which can be dynamically sized for 16 or 32-bit operation. The NEC VR4102/VR4111 can directly support an external LCD controller through a dedicated bus interface. Specific control signals are assigned for an external LCD controller in order to provide an easy interface to the CPU. A 16M byte block of memory is assigned for the LCD controller with its own chip select and ready signals available. Word or byte accesses are controlled by the system high byte signal (SHB#). S1D13A04 X37A-G-007-01 Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 9 2.1.2 LCD Memory Access Cycles Once an address in the LCD block of memory is placed on the external address bus (ADD[25:0]) the LCD chip select (LCDCS#) is driven low. The read enable (RD#) or write enable (WR#) signals are driven low for the appropriate cycle. LCDRDY is driven low by the S1D13A04 to insert wait states into the cycle. The system high byte enable is driven low for 16-bit transfers and high for 8-bit transfers. Figure 2-1: "NEC VR4102/VR4111 Read/Write Cycles," shows the read and write cycles to the LCD Controller Interface. TCLK ADD[25:0] VALID SHB# LCDCS# WR#,RD# D[15:0] (write) VALID D[15:0] (read) Hi-Z VALID Hi-Z LCDRDY Figure 2-1: NEC VR4102/VR4111 Read/Write Cycles Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-007-01 Page 10 Epson Research and Development Vancouver Design Center 3 S1D13A04 Host Bus Interface The S1D13A04 directly supports multiple processors. The S1D13A04 implements a 16-bit Generic #2 Host Bus Interface which is most suitable for direct connection to the NEC VR4102/4111 microprocessor. Generic #2 supports an external Chip Select, shared Read/Write Enable for high byte, and individual Read/Write Enable for low byte. The Generic #2 Host Bus Interface is selected by the S1D13A04 on the rising edge of RESET#. After RESET# is released, the bus interface signals assume their selected configuration. For details on the S1D13A04 configuration, see Section 4.2, "S1D13A04 Hardware Configuration" on page 13. 3.1 Host Bus Interface Pin Mapping The following table shows the functions of each Host Bus Interface signal. Table 3-1: Host Bus Interface Pin Mapping S1D13A04 Pin Names AB[17:0] DB[15:0] WE1# CS# M/R# CLKI BS# RD/WR# RD# WE0# LCDRDY RESET# NEC VR4102/4111 ADD[17:0] DAT[15:0] SHB# LCDCS# ADD18 BUSCLK Connect to IOVDD from the S1D13A04 Connect to IOVDD from the S1D13A04 RD# WR# WAIT# system RESET S1D13A04 X37A-G-007-01 Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 11 3.2 Host Bus Interface Signals The Host Bus Interface requires the following signals: * CLKI is a clock input which is required by the S1D13A04 Host Bus Interface as a source for its internal bus and memory clocks. This clock is typically driven by the host CPU system clock. For this example, BUSCLK from the NEC VR4102/4111 is used for CLKI. * The address inputs AB[17:0], and the data bus DB[15:0], connect directly to the NEC VR4102/4111 address bus (ADD[17:0]) and data bus (DAT[15:0]), respectively. CNF4 must be set to select little endian mode. * Chip Select (CS#) must be driven low by LCDCS# whenever the S1D13A04 is accessed by the VR4102/4111. * M/R# (memory/register) selects between memory or register accesses. This signal is generated by the external address decode circuitry. For this example, M/R# is connected to address line ADD18, allowing system address ADD18 to select between memory or register accesses. * WE1# connects to SHB# (the high byte enable signal from the NEC VR4102/4111) which in conjunction with address bit 0 allows byte steering of read and write operations. * WE0# connects to WR# (the write enable signal from the NEC VR4102/4111) and must be driven low when the VR4102/4111 is writing data to the S1D13A04. * RD# connects to RD# (the read enable signal from the NEC VR4102/4111) and must be driven low when the VR4102/4111 is reading data from the S1D13A04. * WAIT# connects to LCDRDY and is a signal output from the S1D13A04 that indicates the VR4102/VR4111 must wait until data is ready (read cycle) or accepted (write cycle) on the host bus. Since VR4102/VR4111 accesses to the S1D13A04 may occur asynchronously to the display update, it is possible that contention may occur in accessing the S1D13A04 internal registers and/or display buffer. The WAIT# line resolves these contentions by forcing the host to wait until the resource arbitration is complete. * The Bus Status (BS#) and Read/Write (RD/WR#) signals are not used in this implementation of the NEC VR4102/4111 interface using the Generic #2 Host Bus Interface. These pins must be tied high (connected to IO VDD). Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-007-01 Page 12 Epson Research and Development Vancouver Design Center 4 VR4102/VR4111 to S1D13A04 Interface 4.1 Hardware Description The NEC VR4102/VR4111 microprocessor is specifically designed to support an external LCD controller by providing the internal address decoding and control signals necessary. By using the Generic # 2 Host Bus Interface, no glue logic is required to interface the S1D13A04 and the NEC VR4102/VR4111. A pull-up resistor is attached to WAIT# to speed up its rise time when terminating a cycle. BS# (bus start) and RD/WR# are not used by the Generic #2 Host Bus Interface and should be tied high (connected to IO VDD). The following diagram shows a typical implementation of the VR4102/VR4111 to S1D13A04 interface. NEC VR4102/VR4111 WR# SHB# S1D13A04 WE0# WE1# RD# RD# LCDCS# LCDRDY ADD18 Pull-up CS# WAIT# M/R# System RESET RESET# AB[17:0] DB[15:0] CLKI ADD[17:0] DAT[15:0] BUSCLK IO VDD BS# RD/WR# Note: When connecting the S1D13A04 RESET# pin, the system designer should be aware of all conditions that may reset the S1D13A04 (e.g. CPU reset can be asserted during wake-up from power-down modes, or during debug states). Figure 4-1: Typical Implementation of VR4102/VR4111 to S1D13A04 Interface S1D13A04 X37A-G-007-01 Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 13 4.2 S1D13A04 Hardware Configuration The S1D13A04 uses CNF6 through CNF0 to allow selection of the bus mode and other configuration data on the rising edge of RESET#. For details on configuration, refer to the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. The following table shows the configuration required for this implementation of a S1D13A04 to NEC VR4102/4111 interface. Table 4-1: Summary of Power-On/Reset Options S1D13A04 Configuration Input CNF4, CNF[2:0] CNF3 CNF5 CNF6 Power-On/Reset State 1 (connected to IO VDD) Select host bus interface as follows: CNF4 0 CNF2 1 CNF1 0 CNF0 0 Host Bus Generic #2, Little Endian WAIT# is active low CLKI to BCLK divide ratio 1:1 0 (connected to VSS) Reserved. Must be set to 1. WAIT# is active high CLKI to BCLK divide ratio 2:1 configuration for NEC VR4102/VR4111 microprocessor Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-007-01 Page 14 Epson Research and Development Vancouver Design Center 4.3 NEC VR4102/VR4111 Configuration The NEC VR4102/4111 provides the internal address decoding necessary to map an external LCD controller. Physical address 0A00_0000h to 0AFF_FFFFh (16M bytes) is reserved for an external LCD controller by the NEC VR4102/4111. The S1D13A04 is a memory mapped device. The S1D13A04 uses two 256K byte blocks which are selected using ADD18 from the NEC VR4102/4111 (ADD18 is connected to the S1D13A04 M/R# pin).The internal registers occupy the first 256K byte block and the 160K byte display buffer occupies the second 256K byte block. The starting address of the S1D13A04 internal registers is located at 0A00_0000h and the starting address of the display buffer is located at 0A04_0000h. These blocks are aliased over the entire 16M byte address space. Note If aliasing is not desirable, the upper addresses must be fully decoded. The NEC VR4102/VR4111 has a 16-bit internal register named BCUCNTREG2 located at 0B00_0002h. It must be set to the value of 0001h which indicates that LCD controller accesses use a non-inverting data bus. The 16-bit internal register named BCUCNTREG1 (located at 0B00_0000h) must have bit D[13] (ISA/LCD bit) set to 0. This reserves 16M bytes (from 0A00_0000h to 0AFF_FFFFh) for use by the LCD controller and not as ISA bus memory space. S1D13A04 X37A-G-007-01 Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 15 5 Software Test utilities and display drivers are available for the S1D13A04. Full source code is available for both the test utilities and the drivers. The test utilities are configurable for different panel types using a program called 13A04CFG (see document number X37A-B-001-xx), or by directly modifying the source. The display drivers can be customized by the OEM for different panel types, resolutions and color depths only by modifying the source. The S1D13A04 test utilities and display drivers are available from your sales support contact (see Section 7, "Sales and Technical Support") or www.erd.epson.com. Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-007-01 Page 16 Epson Research and Development Vancouver Design Center 6 References 6.1 Documents * NEC Electronics Inc., VR4102/VR4111 64/32-bit Microprocessor Preliminary User's Manual. * Epson Research and Development, Inc., S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. * Epson Research and Development, Inc., S5U13A04B00C Rev. 1.0 Evaluation Board User Manual, document number X37A-G-004-xx. * Epson Research and Development, Inc., S1D13A04 Programming Notes and Examples, document number X37A-G-003-xx. 6.2 Document Sources * NEC Electronics Inc. Website: www.necel.com. * Epson Research and Development Website: www.erd.epson.com. S1D13A04 X37A-G-007-01 Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 17 7 Sales and Technical Support 7.1 EPSON LCD/USB Companion Chips (S1D13A04) Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk/ Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de 7.2 NEC Electronics Inc. NEC Electronics Inc. (U.S.A.) Corporate Headquarters 2880 Scott Blvd. Santa Clara, CA 95050-8062, USA Tel: (800) 366-9782 Fax: (800) 729-9288 http://www.necel.com Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 S1D13A04 X37A-G-007-01 Page 18 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-007-01 Interfacing to the NEC VR4102 / VR4111 Microprocessors Issue Date: 01/10/12 S1D13A04 LCD/USB Companion Chip Interfacing to the NEC VR4181ATM Microprocessor Document Number: X37A-G-008-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All Trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-008-01 Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 3 Table of Contents 1 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Interfacing to the NEC VR4181A . . 2.1 The NEC VR4181A System Bus . 2.1.1 Overview . . . . . . . . . . 2.1.2 LCD Memory Access Signals . . . . ....... ...... ........ ........ ... .. ... ... . . . . ...... ..... ....... ....... . . . . ....... ...... ........ ........ .8 .8 .8 .9 3 S1D13A04 Host Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 3.1 Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . 10 3.2 Host Bus Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . 11 VR4181A to S1D13A04 Interface . . . 4.1 Hardware Description . . . . . . 4.2 S1D13A04 Hardware Configuration 4.3 NEC VR4181A Configuration . . . . . . . ... .. .. .. . . . . . . . . . . . . ... .. .. .. . . . . . . . . . . . . ... .. .. .. . . . . . . . . . . . . ... .. .. .. . . . . . . . . . . . . 12 12 13 14 4 5 6 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7.1 EPSON LCD/USB Companion Chips (S1D13A04) . . . . . . . . . . . . . . . 17 7.2 NEC Electronics Inc. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 7 Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-008-01 Page 4 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-008-01 Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 5 List of Tables Table 3-1: Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Table 4-1: Summary of Power-On/Reset Options . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 List of Figures Figure 4-1: Typical Implementation of VR4181A to S1D13A04 Interface . . . . . . . . . . . . . . 12 Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-008-01 Page 6 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-008-01 Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 7 1 Introduction This application note describes the hardware and software environment required to interface the S1D13A04 LCD/USB Companion Chip and the NEC VR4181A microprocessor. The NEC VR4181A microprocessor is specifically designed to support an external LCD controller. The designs described in this document are presented only as examples of how such interfaces might be implemented. This application note is updated as appropriate. Please check the Epson Research and Development website at www.erd.epson.com for the latest revision of this document before beginning any development. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-008-01 Page 8 Epson Research and Development Vancouver Design Center 2 Interfacing to the NEC VR4181A 2.1 The NEC VR4181A System Bus The VR-Series family of microprocessors features a high-speed synchronous system bus typical of modern microprocessors. Designed with external LCD controller support and Windows(R) CE based embedded consumer applications in mind, the VR4181A offers a highly integrated solution for portable systems. This section is an overview of the operation of the CPU bus to establish interface requirements. 2.1.1 Overview The NEC VR4181A is designed around the RISC architecture developed by MIPS. This microprocessor is designed around the 100MHz VR4110 CPU core which supports the MIPS III and MIPS16 instruction sets. The CPU communicates with external devices via an ISA interface. While the VR4181A has an embedded LCD controller, this internal controller can be disabled to provide direct support for an external LCD controller through its external ISA bus. A 64 to 512K byte block of memory is assigned to the external LCD controller with a dedicated chip select signal (LCDCS#). Word or byte accesses are controlled by the system high byte signal (#UBE). S1D13A04 X37A-G-008-01 Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 9 2.1.2 LCD Memory Access Signals The S1D13A04 requires an addressing range of 256K bytes. When the VR4181A external LCD controller chip select signal is programmed to a window of that size, the S1D13A04 resides in the VR4181A physical address range of 133C 0000h to 133F FFFFh. This range is part of the external ISA memory space. The following signals are required to access an external LCD controller. All signals obey ISA signalling rules. * A[16:0] is the address bus. * #UBE is the high byte enable (active low). * #LCDCS is the chip select for the S1D13A04 (active low). * D[15:0] is the data bus. * #MEMRD is the read command (active low). * #MEMWR is the write command (active low). * #MEMCS16 is the acknowledge for 16-bit peripheral capability (active low). * IORDY is the ready signal from S1D13A04. * SYSCLK is the prescalable bus clock (optional). Once an address in the LCD block of memory is accessed, the LCD chip select (#LCDCS) is driven low. The read or write enable signals (#MEMRD or #MEMWR) are driven low for the appropriate cycle and IORDY is driven low by the S1D13A04 to insert wait states into the cycle. The high byte enable (UBE#) is driven low for 16-bit transfers and high for 8-bit transfers. Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-008-01 Page 10 Epson Research and Development Vancouver Design Center 3 S1D13A04 Host Bus Interface The S1D13A04 directly supports multiple processors. The S1D13A04 implements a 16-bit Generic #2 Host Bus Interface which is most suitable for direct connection to the NEC VR4181A microprocessor. Generic #2 supports an external Chip Select, shared Read/Write Enable for high byte, and individual Read/Write Enable for low byte. The Generic #2 Host Bus Interface is selected by the S1D13A04 on the rising edge of RESET#. After RESET# is released, the bus interface signals assume their selected configuration. For details on the S1D13A04 configuration, see Section 4.2, "S1D13A04 Hardware Configuration" on page 13. 3.1 Host Bus Interface Pin Mapping The following table shows the functions of each Host Bus Interface signal. Table 3-1: Host Bus Interface Pin Mapping S1D13A04 Pin Names AB[17:0] DB[15:0] WE1# CS# M/R# CLKI BS# RD/WR# RD# WE0# WAIT# RESET# NEC VR4181A A[17:0] D[15:0] #UBE #LCDCS A18 SYSCLK Connect to IOVDD from the S1D13A04 Connect to IOVDD from the S1D13A04 #MEMRD #MEMWR IORDY RESET# S1D13A04 X37A-G-008-01 Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 11 3.2 Host Bus Interface Signals The interface requires the following signals. * CLKI is a clock input which is required by the S1D13A04 Host Bus Interface as a source for its internal bus and memory clocks. This clock is typically driven by the host CPU system clock. For this example, SYSCLK from the NEC VR4181A is used for CLKI. * The address inputs AB[17:0], and the data bus DB[15:0], connect directly to the NEC VR4181A address (A[17:0]) and data bus (D[15:0]), respectively. CNF4 must be set to select little endian mode. * Chip Select (CS#) must be driven low by #LCDCS whenever the S1D13A04 is accessed by the VR4181A. * M/R# (memory/register) selects between memory or register accesses. This signal is generated by the external address decode circuitry. For this example, M/R# is connected to address line A18, allowing system address A18 to select between memory or register accesses. * WE1# connects to #UBE (the high byte enable signal from the NEC VR4181A) which in conjunction with address bit 0 allows byte steering of read and write operations. * WE0# connects to #MEMWR (the write enable signal from the NEC VR4181A) and must be driven low when the NEC VR4181A is writing data to the S1D13A04. * RD# connects to #MEMRD (the read enable signal from the NEC VR4181A) and must be driven low when the NEC VR4181A is reading data from the S1D13A04. * WAIT# connects to IORDY and is a signal which is output from the S1D13A04 which indicates the NEC VR4181A must wait until data is ready (read cycle) or accepted (write cycle) on the host bus. Since VR4181A accesses to the S1D13A04 may occur asynchronously to the display update, it is possible that contention may occur in accessing the S1D13A04 internal registers and/or display buffer. The WAIT# line resolves these contentions by forcing the host to wait until the resource arbitration is complete. * The Bus Status (BS#) and Read/Write (RD/WR#) signals are not used in this implementation of the NEC VR4181A interface using the Generic #2 Host Bus Interface. These pins must be tied high (connected to IO VDD). Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-008-01 Page 12 Epson Research and Development Vancouver Design Center 4 VR4181A to S1D13A04 Interface 4.1 Hardware Description The NEC VR4181A microprocessor is specifically designed to support an external LCD controller by providing the internal address decoding and control signals necessary. By using the Generic # 2 Host Bus Interface, no glue logic is required to interface the S1D13A04 to the NEC VR4181A. A pull-up resistor is attached to WAIT# to speed up its rise time when terminating a cycle. #MEMCS16 of the NEC VR4181A is connected to #LCDCS to signal that the S1D13A04 is capable of 16-bit transfers. BS# (bus start) and RD/WR# are not used by the Generic #2 Host Bus Interface and should be tied high (connected to IO VDD). The diagram below shows a typical implementation of the VR4181A to S1D13A04 interface. NEC VR4181A #MEMWR #UBE #MEMRD A18 #LCDCS IORDY Pull-up S1D13A04 WE0# WE1# RD# M/R# CS# WAIT# #MEMCS16 System RESET A[17:0] D[15:0] SYSCLK IO VDD RESET# AB[17:0] DB[15:0] CLKI BS# RD/WR# Note: When connecting the S1D13A04 RESET# pin, the system designer should be aware of all conditions that may reset the S1D13A04 (e.g. CPU reset can be asserted during wake-up from power-down modes, or during debug states). Figure 4-1: Typical Implementation of VR4181A to S1D13A04 Interface S1D13A04 X37A-G-008-01 Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 13 4.2 S1D13A04 Hardware Configuration The S1D13A04 uses CNF6 through CNF0 to allow selection of the bus mode and other configuration data on the rising edge of RESET#. For details on configuration, refer to the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. The following table shows the configuration required for this implementation of a S1D13A04 to NEC VR4181A interface. Table 4-1: Summary of Power-On/Reset Options S1D13A04 Configuration Input CNF4, CNF[2:0] CNF3 CNF5 CNF6 Power-On/Reset State 1 (connected to IO VDD) Select host bus interface as follows: CNF4 0 CNF2 1 CNF1 0 CNF0 0 Host Bus Generic #2, Little Endian WAIT# is active low CLKI to BCLK divide ratio 1:1 0 (connected to VSS) Reserved. Must be set to 1. WAIT# is active high CLKI to BCLK divide ratio 2:1 configuration for NEC VR4181A microprocessor Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-008-01 Page 14 Epson Research and Development Vancouver Design Center 4.3 NEC VR4181A Configuration The S1D13A04 is a memory mapped device. The S1D13A04 uses two 256K byte blocks which are selected using A18 from the NEC VR4181A (A18 is connected to the S1D13A04 M/R# pin).The internal registers occupy the first 256K byte block and the 160K byte display buffer occupies the second 256K byte block. When the VR4181A embedded LCD controller is disabled, the external LCD controller chip select signal (#LCDCS) decodes either a 64K byte, 128K byte, 256K byte, or 512K byte memory block in the VR4181A external ISA memory. The S1D13A04 requires this block of memory to be set to 512K bytes. With this configuration, the S1D13A04 internal registers starting address is located at physical memory location 133C_0000h and the display buffer is located at memory location 1340_0000h. The NEC VR4181A must be configured through its internal registers to map the S1D13A04 to the external LCD controller space. The following register values must be set. * Register LCDGPMD at address 0B00_032Eh must be set as follows. * Bit 7 must be set to 1 to disable the internal LCD controller and enable the external LCD controller interface. Disabling the internal LCD controller also maps pin SHCLK to #LCDCS and pin LOCLK to #MEMCS16. * Bits [1:0] must be set to 11b to reserve 512Kbytes of memory address range, 133C_0000h to 1343_FFFFh for the external LCD controller. * Register GPMD2REG at address 0B00_0304h must be set as follows. * Bits [9:8] (GP20MD[1:0]) must be set to 11'b to map pin GPIO20 to #UBE. * Bits [5:4] (GP18MD[1:0]) must be set to 01'b to map pin GPIO18 to IORDY. S1D13A04 X37A-G-008-01 Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 15 5 Software Test utilities and display drivers are available for the S1D13A04. Full source code is available for both the test utilities and the drivers. The test utilities are configurable for different panel types using a program called 13A04CFG (see document number X37A-B-001-xx), or by directly modifying the source. The display drivers can be customized by the OEM for different panel types, resolutions and color depths only by modifying the source. The S1D13A04 test utilities and display drivers are available from your sales support contact (see Section 7, "Sales and Technical Support") or www.erd.epson.com. Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-008-01 Page 16 Epson Research and Development Vancouver Design Center 6 References 6.1 Documents * NEC Electronics Inc., NEC VR4181A Target Specification, Revision 0.5, 9/11/98 * Epson Research and Development, Inc., S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. * Epson Research and Development, Inc., S5U13A04B00C Rev. 1.0 Evaluation Board User Manual, document number X37A-G-004-xx. * Epson Research and Development, Inc., S1D13A04 Programming Notes and Examples, document number X37A-G-003-xx. 6.2 Document Sources * NEC Electronics Inc.Website: www.necel.com. * Epson Research and Development Website: www.erd.epson.com. S1D13A04 X37A-G-008-01 Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 17 7 Sales and Technical Support 7.1 EPSON LCD/USB Companion Chips (S1D13A04) Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk/ Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de 7.2 NEC Electronics Inc. NEC Electronics Inc. (U.S.A.) Corporate Headquarters 2880 Scott Blvd. Santa Clara, CA 95050-8062, USA Tel: (800) 366-9782 Fax: (800) 729-9288 http://www.necel.com Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-008-01 Page 18 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-008-01 Interfacing to the NEC VR4181ATM Microprocessor Issue Date: 01/10/12 S1D13A04 LCD/USB Companion Chip Interfacing to the Motorola MPC82x Microprocessor Document Number: X37A-G-009-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All Trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-009-01 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 3 Table of Contents 1 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Interfacing to the MPC82x . . . . . . . . . . . . . . . . 2.1 The MPC8xx System Bus . . . . . . . . . . . . . 2.2 MPC8xx Bus Overview . . . . . . . . . . . . . 2.2.1 Normal (Non-Burst) Bus Transactions . . . . . . . 2.2.2 Burst Cycles . . . . . . . . . . . . . . . . . . . . . 2.3 Memory Controller Module . . . . . . . . . . . . 2.3.1 General-Purpose Chip Select Module (GPCM) . . . 2.3.2 User-Programmable Machine (UPM) . . . . . . . . . . . . . . . . ...... ..... ..... ....... ....... ..... ....... ....... . . . . . . . . ....... ...... ...... ........ ........ ...... ........ ........ .8 .8 .8 .9 10 11 11 12 3 S1D13A04 Host Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 3.1 Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . 13 3.2 Host Bus Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . 14 MPC82x to S1D13A04 Interface . . . . . . . . . . . . . 4.1 Hardware Description . . . . . . . . . . . . . . 4.2 MPC821ADS Evaluation Board Hardware Connections . 4.3 S1D13A04 Hardware Configuration . . . . . . . . 4.4 Register/Memory Mapping . . . . . . . . . . . . 4.5 MPC82x Chip Select Configuration . . . . . . . . . 4.6 Test Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ... .. .. .. .. .. .. . . . . . . . . . . . . . . . . . . . . . ... .. .. .. .. .. .. . . . . . . . . . . . . . . . . . . . . . 15 15 16 18 18 19 20 4 5 6 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 7.1 EPSON LCD/USB Companion Chips (S1D13A04) . . . . . . . . . . . . . . . 23 7.2 Motorola MPC821 Processor . . . . . . . . . . . . . . . . . . . . . . . . 23 7 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 S1D13A04 X37A-G-009-01 Page 4 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-009-01 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 5 List of Tables Table 3-1: Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Table 4-1: List of Connections from MPC821ADS to S1D13A04 . . . . . . . . . . . . . . . . . 16 Table 4-2: Summary of Power-On/Reset Options . . . . . . . . . . . . . . . . . . . . . . . . . . 18 List of Figures Figure 2-1: Figure 2-2: Figure 2-3: Figure 4-1: Power PC Memory Read Cycle . . . . . . . . . . . . . . . Power PC Memory Write Cycle . . . . . . . . . . . . . . . GPCM Memory Devices Timing . . . . . . . . . . . . . . Typical Implementation of MPC82x to S1D13A04 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 . 10 . 12 . 15 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 S1D13A04 X37A-G-009-01 Page 6 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-009-01 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 7 1 Introduction This application note describes the hardware and software environment required to interface the S1D13A04 LCD/USB Companion Chip and the Motorola MPC82x microprocessor. The designs described in this document are presented only as examples of how such interfaces might be implemented. This application note is updated as appropriate. Please check the Epson Research and Development website at www.erd.epson.com for the latest revision of this document before beginning any development. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 S1D13A04 X37A-G-009-01 Page 8 Epson Research and Development Vancouver Design Center 2 Interfacing to the MPC82x 2.1 The MPC8xx System Bus The MPC8xx family of processors feature a high-speed synchronous system bus typical of modern RISC microprocessors. This section provides an overview of the operation of the CPU bus in order to establish interface requirements. 2.2 MPC8xx Bus Overview The MPC8xx microprocessor family uses a synchronous address and data bus. All IO is synchronous to a square-wave reference clock called MCLK (Master Clock). This clock runs at the machine cycle speed of the CPU core (typically 25 to 50 MHz). Most outputs from the processor change state on the rising edge of this clock. Similarly, most inputs to the processor are sampled on the rising edge. Note The external bus can run at one-half the CPU core speed using the clock control register. This is typically used when the CPU core is operated above 50 MHz. The MPC821 can generate up to eight independent chip select outputs, each of which may be controlled by one of two types of timing generators: the General Purpose Chip Select Module (GPCM) or the User-Programmable Machine (UPM). Examples are given using the GPCM. It should be noted that all Power PC microprocessors, including the MPC8xx family, use bit notation opposite from the convention used by most other microprocessor systems. Bit numbering for the MPC8xx always starts with zero as the most significant bit, and increments in value to the least-significant bit. For example, the most significant bits of the address bus and data bus are A0 and D0, while the least significant bits are A31 and D31. The MPC8xx uses both a 32-bit address and data bus. A parity bit is supported for each of the four byte lanes on the data bus. Parity checking is done when data is read from external memory or peripherals, and generated by the MPC8xx bus controller on write cycles. All IO accesses are memory-mapped meaning there is no separate IO space in the Power PC architecture. Support is provided for both on-chip (DMA controllers) and off-chip (other processors and peripheral controllers) bus masters. For further information on this topic, refer to Section 6, "References" on page 22. The bus can support both normal and burst cycles. Burst memory cycles are used to fill on-chip cache memory, and for certain on-chip DMA operations. Normal cycles are used for all other data transfers. S1D13A04 X37A-G-009-01 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 9 2.2.1 Normal (Non-Burst) Bus Transactions A data transfer is initiated by the bus master by placing the memory address on address lines A0 through A31 and driving TS (Transfer Start) low for one clock cycle. Several control signals are also provided with the memory address: * TSIZ[0:1] (Transfer Size) -- indicates whether the bus cycle is 8, 16, or 32-bit. * RD/WR -- set high for read cycles and low for write cycles. * AT[0:3] (Address Type Signals) -- provides more detail on the type of transfer being attempted. When the peripheral device being accessed has completed the bus transfer, it asserts TA (Transfer Acknowledge) for one clock cycle to complete the bus transaction. Once TA has been asserted, the MPC821 will not start another bus cycle until TA has been de-asserted. The minimum length of a bus transaction is two bus clocks. Figure 2-1: "Power PC Memory Read Cycle" illustrates a typical memory read cycle on the Power PC system bus. SYSCLK TS TA A[0:31] RD/WR TSIZ[0:1], AT[0:3] D[0:31] Transfer Start Wait States Transfer Complete Sampled when TA low Next Transfer Starts Figure 2-1: Power PC Memory Read Cycle Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 S1D13A04 X37A-G-009-01 Page 10 Epson Research and Development Vancouver Design Center Figure 2-2: "Power PC Memory Write Cycle" illustrates a typical memory write cycle on the Power PC system bus. SYSCLK TS TA A[0:31] RD/WR TSIZ[0:1], AT[0:3] D[0:31] Transfer Start Valid Wait States Transfer Complete Next Transfer Starts Figure 2-2: Power PC Memory Write Cycle If an error occurs, TEA (Transfer Error Acknowledge) is asserted and the bus cycle is aborted. For example, a peripheral device may assert TEA if a parity error is detected, or the MPC821 bus controller may assert TEA if no peripheral device responds at the addressed memory location within a bus time-out period. For 32-bit transfers, all data lines (D[0:31]) are used and the two low-order address lines A30 and A31 are ignored. For 16-bit transfers, data lines D0 through D15 are used and address line A31 is ignored. For 8-bit transfers, data lines D0 through D7 are used and all address lines (A[0:31]) are used. Note This assumes that the Power PC core is operating in big endian mode (typically the case for embedded systems). 2.2.2 Burst Cycles Burst memory cycles are used to fill on-chip cache memory and to carry out certain on-chip DMA operations. They are very similar to normal bus cycles with the following exceptions: * Always 32-bit. * Always attempt to transfer four 32-bit words sequentially. * Always address longword-aligned memory (i.e. A30 and A31 are always 0:0). * Do not increment address bits A28 and A29 between successive transfers; the addressed device must increment these address bits internally. S1D13A04 X37A-G-009-01 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 11 If a peripheral is not capable of supporting burst cycles, it can assert Burst Inhibit (BI) simultaneously with TA, and the processor reverts to normal bus cycles for the remaining data transfers. Burst cycles are mainly intended to facilitate cache line fills from program or data memory. They are normally not used for transfers to/from IO peripheral devices such as the S1D13A04, therefore the interfaces described in this document do not attempt to support burst cycles. 2.3 Memory Controller Module 2.3.1 General-Purpose Chip Select Module (GPCM) The General-Purpose Chip Select Module (GPCM) is used to control memory and peripheral devices which do not require special timing or address multiplexing. In addition to the chip select output, it can generate active-low Output Enable (OE) and Write Enable (WE) signals compatible with most memory and x86-style peripherals. The MPC821 bus controller also provides a Read/Write (RD/WR) signal which is compatible with most 68K peripherals. The GPCM is controlled by the values programmed into the Base Register (BR) and Option Register (OR) of the respective chip select. The Option Register sets the base address, the block size of the chip select, and controls the following timing parameters: * The ACS bit field allows the chip select assertion to be delayed with respect to the address bus valid, by 0, 1/4, or 1/2 clock cycle. * The CSNT bit causes chip select and WE to be negated 1/2 clock cycle earlier than normal. * The TRLX (relaxed timing) bit inserts an additional one clock delay between assertion of the address bus and chip select. This accommodates memory and peripherals with long setup times. * The EHTR (Extended hold time) bit inserts an additional 1-clock delay on the first access to a chip select. * Up to 15 wait states may be inserted, or the peripheral can terminate the bus cycle itself by asserting TA (Transfer Acknowledge). * Any chip select may be programmed to assert BI (Burst Inhibit) automatically when its memory space is addressed by the processor core. Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 S1D13A04 X37A-G-009-01 Page 12 Epson Research and Development Vancouver Design Center Figure 2-3: "GPCM Memory Devices Timing" illustrates a typical cycle for a memory mapped device using the GPCM of the Power PC. CLOCK A[0:31] TS TA CS WE OE Valid D[0:31] Figure 2-3: GPCM Memory Devices Timing 2.3.2 User-Programmable Machine (UPM) The UPM is typically used to control memory types, such as Dynamic RAMs, which have complex control or address multiplexing requirements. The UPM is a general purpose RAM-based pattern generator which can control address multiplexing, wait state generation, and five general-purpose output lines on the MPC821. Up to 64 pattern locations are available, each 32 bits wide. Separate patterns may be programmed for normal accesses, burst accesses, refresh (timer) events, and exception conditions. This flexibility allows almost any type of memory or peripheral device to be accommodated by the MPC821. In this application note, the GPCM is used instead of the UPM, since the GPCM has enough flexibility to accommodate the S1D13A04 and it is desirable to leave the UPM free to handle other interfacing duties, such as EDO DRAM. S1D13A04 X37A-G-009-01 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 13 3 S1D13A04 Host Bus Interface The S1D13A04 directly supports multiple processors. The S1D13A04 implements a 16-bit Generic #1 Host Bus Interface which is most suitable for direct connection to the Motorola MPC82x microprocessor. Generic #1 supports a Chip Select and an individual Read Enable/Write Enable for each byte. The Generic #1 Host Bus Interface is selected by the S1D13A04 on the rising edge of RESET#. After RESET# is released, the bus interface signals assume their selected configuration. For details on the S1D13A04 configuration, see Section 4.3, "S1D13A04 Hardware Configuration" on page 18. 3.1 Host Bus Interface Pin Mapping The following table shows the functions of each Host Bus Interface signal. Table 3-1: Host Bus Interface Pin Mapping S1D13A04 Pin Names AB[17:0] DB[15:0] WE1# CS# M/R# CLKI BS# RD/WR# RD# WE0# WAIT# RESET# Motorola MPC82x A[14:31] D[0:15] WE0 CS4 A13 SYSCLK Connect to IOVDD from the S1D13A04 OE (see note) OE (see note) WE1 TA System RESET Note The Motorola MPC82x chip select module only handles 16-bit read cycles. As the S1D13A04 uses the chip select module to generate CS#, only 16-bit read cycles are possible and both the high and low byte enables can be driven by the MPC82x signal OE. Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 S1D13A04 X37A-G-009-01 Page 14 Epson Research and Development Vancouver Design Center 3.2 Host Bus Interface Signals The Host Bus Interface requires the following signals. * CLKI is a clock input which is required by the S1D13A04 Host Bus Interface as a source for its internal bus and memory clocks. This clock is typically driven by the host CPU system clock. For this example, SYSCLK from the Motorola MPC82x is used for CLKI. * The address inputs AB[17:0], and the data bus DB[15:0], connect directly to the MPC82x address (A[14:31]) and data bus (D[0:15]), respectively. CNF4 must be set to select big endian mode. * Chip Select (CS#) must be driven low by CS4 whenever the S1D13A04 is accessed by the Motorola MPC82x. * M/R# (memory/register) selects between memory or register accesses. This signal is generated by the external address decode circuitry. For this example, M/R# is connected to address line A13, allowing system address A13 to select between memory or register accesses. * WE0# connects to WE1 (the low byte enable signal from the MPC82x) and must be driven low when the MPC82x is writing the low byte to the S1D13A04. * WE1# connects to WE0 (the high byte enable signal from the MPC82x) and must be driven low when the MPC82x is writing the high byte to the S1D13A04. * RD# and RD/WR# are read enables for the low-order and high-order bytes, respectively. Both signals are driven low by OE when the Motorola MPC82x is reading data from the S1D13A04. * WAIT# connects to TA and is a signal which is output from the S1D13A04 which indicates the MPC82x must wait until data is ready (read cycle) or accepted (write cycle) on the host bus. Since MPC82x accesses to the S1D13A04 may occur asynchronously to the display update, it is possible that contention may occur in accessing the S1D13A04 internal registers and/or display buffer. The WAIT# line resolves these contentions by forcing the host to wait until the resource arbitration is complete. * The Bus Status (BS#) signal is not used in this implementation of the MPC82x interface using the Generic #1 Host Bus Interface. This pin must be tied high (connected to IO VDD). S1D13A04 X37A-G-009-01 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 15 4 MPC82x to S1D13A04 Interface 4.1 Hardware Description The interface between the S1D13A04 and the MPC82x requires no external glue logic. The polarity of the WAIT# signal must be selected as active high by connecting CNF5 to IO VDD (see Table 4-2:, "Summary of Power-On/Reset Options," on page 18). BS# (bus start) is not used in this implementation and should be tied high (connected to IO VDD). The following diagram shows a typical implementation of the MPC82x to S1D13A04 interface. MPC82x A[14:31] D[0:15] CS4 A13 IO VDD S1D13A04 AB[17:0] DB[15:0] CS# M/R# BS# TA WE0 WE1 OE WAIT# WE1# WE0# RD/WR# RD# SYSCLK System RESET CLKI RESET# Note: When connecting the S1D13A04 RESET# pin, the system designer should be aware of all conditions that may reset the S1D13A04 (e.g. CPU reset can be asserted during wake-up from power-down modes, or during debug states). Figure 4-1: Typical Implementation of MPC82x to S1D13A04 Interface Table 4-1:, "List of Connections from MPC821ADS to S1D13A04" on page 16 shows the connections between the pins and signals of the MPC82x and the S1D13A04. Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 S1D13A04 X37A-G-009-01 Page 16 Epson Research and Development Vancouver Design Center Note The interface was designed using a Motorola MPC821 Application Development System (ADS). The ADS board has 5 volt logic connected to the data bus, so the interface included two 74F245 octal buffers on D[0:15] between the ADS and the S1D13A04. In a true 3 volt system, no buffering is necessary. 4.2 MPC821ADS Evaluation Board Hardware Connections The following table details the connections between the pins and signals of the MPC821 and the S1D13A04. Table 4-1: List of Connections from MPC821ADS to S1D13A04 MPC821 Signal Name 2.0V (see note 1) 3.3V A14 (see note 2) A15 (see note 2) A16 (see note 2) A17 (see note 2) A18 (see note 2) A19 (see note 2) A20 (see note 2) A21 (see note 2) A22 (see note 2) A23 (see note 2) A24 (see note 2) A25 (see note 2) A26 (see note 2) A27 (see note 2) A28 (see note 2) A29 (see note 2) A30 (see note 2) A31 (see note 2) D0 (see note 3) D1 (see note 3) D2 (see note 3) D3 (see note 3) D4 (see note 3) D5 (see note 3) D6 (see note 3) D7 (see note 3) D8 (see note 3) D9 (see note 3) MPC821ADS Connector and Pin Name P9-D24 P9-A22 P6-C20 P6-D20 P6-B24 P6-C24 P6-D23 P6-D22 P6-D19 P6-A19 P6-D28 P6-A28 P6-C27 P6-A26 P6-C26 P6-A25 P6-D26 P6-B25 P6-B19 P6-D17 P12-A9 P12-C9 P12-D9 P12-A8 P12-B8 P12-D8 P12-B7 P12-C7 P12-A15 P12-C15 S1D13A04 Signal Name COREVDD IOVDD AB17 AB16 AB15 AB14 AB13 AB12 AB11 AB10 AB9 AB8 AB7 AB6 AB5 AB4 AB3 AB2 AB1 AB0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 S1D13A04 X37A-G-009-01 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 17 Table 4-1: List of Connections from MPC821ADS to S1D13A04 (Continued) MPC821 Signal Name D10 (see note 3) D11 (see note 3) D12 (see note 3) D13 (see note 3) D14 (see note 3) D15 (see note 3) SRESET SYSCLK CS4 TA WE0 WE1 OE A13 MPC821ADS Connector and Pin Name P12-D15 P12-A14 P12-B14 P12-D14 P12-B13 P12-C13 P9-D15 P9-C2 P6-D13 P6-B6 to inverter enabled by CS# P6-B15 P6-A14 P6-B16 P6-C21 P12-A1, P12-B1, P12-A2, P12-B2, P12-A3, P12-B3, P12-A4, P12-B4, P12-A5, P12-B5, P12-A6, P12-B6, P12-A7 S1D13A04 Signal Name D5 D4 D3 D2 D1 D0 RESET# CLKI CS# WAIT# WE1# WE0# RD/WR#, RD# M/R# GND Vss Note 1. The PCMCIA connector (P9) provides 2.0V on D[23:25] and can be used as the source for COREVDD. However, at 2.0V the S1D13A04 MCLK is has a maximum frequency of 30MHz. To increase memory performance (MCLK maximum = 50MHz) an external 2.5V power supply must be connected to COREVDD. 2. The bit numbering of the Motorola MPC821 bus signals is reversed from the normal convention, e.g.: the most significant address bit is A0, the next is A1, A2, etc. 3. The bit numbering of the Motorola MPC821 data signals is reversed from the normal convention, e.g.: the most significant address bit is D0, the next is D1, D2, etc. Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 S1D13A04 X37A-G-009-01 Page 18 Epson Research and Development Vancouver Design Center 4.3 S1D13A04 Hardware Configuration The S1D13A04 uses CNF6 through CNF0 to allow selection of the bus mode and other configuration data on the rising edge of RESET#. For details on configuration, refer to the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. The following table shows the configuration required for this implementation of a S1D13A04 to Motorola MPC82x microprocessor. Table 4-2: Summary of Power-On/Reset Options S1D13A04 Configuration Input CNF4, CNF[2:0] CNF3 CNF5 CNF6 Power-On/Reset State 1 (connected to IO VDD) Select host bus interface as follows: CNF4 1 CNF2 0 CNF1 1 CNF0 1 Host Bus Generic #1, Big Endian WAIT# is active low CLKI to BCLK divide ratio 1:1 0 (connected to VSS) Reserved. Must be set to 1. WAIT# is active high CLKI to BCLK divide ratio 2:1 configuration for Motorola MPC82x microprocessor 4.4 Register/Memory Mapping The DRAM on the MPC821 ADS board extends from address 0 through 3F FFFFh, so the S1D13A04 is addressed starting at 40 0000h. The S1D13A04 uses two 256K byte blocks which are selected using A13 from the MPC821 (A13 is connected to the S1D13A04 M/R# pin). The internal registers occupy the first 256K byte block and the 160K byte display buffer occupies the second 256K byte block. S1D13A04 X37A-G-009-01 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 19 4.5 MPC82x Chip Select Configuration Chip select 4 is used to control the S1D13A04. The following options are selected in the base address register (BR4). * BA (0:16) = 0000 0000 0100 0000 0 - set starting address of S1D13A04 to 40 0000h * AT (0:2) = 0 - ignore address type bits. * PS (0:1) = 1:0 - memory port size is 16 bits * PARE = 0 - disable parity checking * WP = 0 - disable write protect * MS (0:1) = 0:0 - select General Purpose Chip Select module to control this chip select * V = 1 - set valid bit to enable chip select The following options were selected in the option register (OR4). * AM (0:16) = 1111 1111 1100 0000 0 - mask all but upper 10 address bits; S1D13A04 consumes 4M byte of address space * ATM (0:2) = 0 - ignore address type bits * CSNT = 0 - normal CS/WE negation * ACS (0:1) = 1:1 - delay CS assertion by 1/2 clock cycle from address lines * BI = 1 - assert Burst Inhibit * SCY (0:3) = 0 - wait state selection; this field is ignored since external transfer acknowledge is used; see SETA below * SETA = 1 - the S1D13A04 generates an external transfer acknowledge using the WAIT# line * TRLX = 0 - normal timing * EHTR = 0 - normal timing Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 S1D13A04 X37A-G-009-01 Page 20 Epson Research and Development Vancouver Design Center 4.6 Test Software The test software to exercise this interface is very simple. It configures chip select 4 (CS4) on the MPC82x to map the S1D13A04 to an unused 512K byte block of address space and loads the appropriate values into the option register for CS4. Then the software runs a tight loop reading the S1D13A04 Revision Code Register REG[00h]. This allows monitoring of the bus timing on a logic analyzer. The following source code was entered into the memory of the MPC821ADS using the line-by-line assembler in MPC8BUG (the debugger provided with the ADS board). Once the program was executed on the ADS, a logic analyzer was used to verify operation of the interface hardware. It is important to note that when the MPC821 comes out of reset, its on-chip caches and MMU are disabled. If the data cache is enabled, then the MMU must be set up so that the S1D13A04 memory block is tagged as non-cacheable, to ensure that accesses to the S1D13A04 occurs in proper order, and also to ensure that the MPC821 does not attempt to cache any data read from or written to the S1D13A04 or its display buffer. The source code for this test routine is as follows: BR4 OR4 MemStart RevCodeReg Start equ equ equ equ mfspr andis. andis. oris ori stw andis. oris ori stw andis. oris lbz b $120 $124 $44 0000 $40 0000 r1,IMMR r1,r1,$ffff r2,r0,0 r2,r2,MemStart r2,r2,$0801 r2,BR4(r1) r2,r0,0 r2,r2,$ffc0 r2,r2,$0708 ; ; ; ; CS4 base register CS4 option register address of S1D13A04 display buffer address of Revision Code Register get base address of internal registers clear lower 16 bits to 0 clear r2 write base address port size 16 bits; select GPCM; enable write value to base register clear r2 address mask - use upper 10 bits normal CS negation; delay CS 1/2 clock; inhibit burst write to option register clear r1 point r1 to start of S1D13A04 mem space read revision code into r1 branch forever Loop ; ; ; ; ; ; ; ; ; ; r2,OR4(r1) ; r1,r0,0 ; r1,r1,MemStart ; r0,RevCodeReg(r1) ; Loop ; end Note MPC8BUG does not support comments or symbolic equates. These have been added for clarity only. S1D13A04 X37A-G-009-01 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 21 5 Software Test utilities and display drivers are available for the S1D13A04. Full source code is available for both the test utilities and the drivers. The test utilities are configurable for different panel types using a program called 13A04CFG (see document number X37A-B-001-xx), or by directly modifying the source. The display drivers can be customized by the OEM for different panel types, resolutions and color depths only by modifying the source. The S1D13A04 test utilities and display drivers are available from your sales support contact (see Section 7, "Sales and Technical Support") or www.erd.epson.com. Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 S1D13A04 X37A-G-009-01 Page 22 Epson Research and Development Vancouver Design Center 6 References 6.1 Documents * Motorola Inc., Power PC MPC821 Portable Systems Microprocessor User's Manual, Motorola Publication no. MPC821UM/; available on the Internet at http://www.mot.com/SPS/ADC/pps/_subpgs/_documentation/821/821UM.html. * Epson Research and Development, Inc., S1D13A04 Hardware Functional Specification, Document Number X37A-A-001-xx. * Epson Research and Development, Inc., S5U13A04B00C Rev. 1.0 Evaluation Board User Manual, Document Number X37A-G-004-xx. * Epson Research and Development, Inc., S1D13A04 Programming Notes and Examples, Document Number X37A-G-003-xx. 6.2 Document Sources * Motorola Inc. Literature Distribution Center: (800) 441-2447. * Motorola Inc. Website: www.mot.com. * Epson Research and Development Website: www.erd.epson.com. S1D13A04 X37A-G-009-01 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 Epson Research and Development Vancouver Design Center Page 23 7 Sales and Technical Support 7.1 EPSON LCD/USB Companion Chips (S1D13A04) Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk/ Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de 7.2 Motorola MPC821 Processor * Motorola Design Line, (800) 521-6274. * Local Motorola sales office or authorized distributor. Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 S1D13A04 X37A-G-009-01 Page 24 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-009-01 Interfacing to the Motorola MPC82x Microprocessor Issue Date: 01/10/05 S1D13A04 LCD/USB Companion Chip Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Document Number: X37A-G-010-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All Trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-010-01 Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 3 Table of Contents 1 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Interfacing to the MCF5307 . . . . . . . . . . . . 2.1 The MCF5307 System Bus . . . . . . . . . . 2.1.1 Overview . . . . . . . . . . . . . . . . . . . 2.1.2 Normal (Non-Burst) Bus Transactions . . . . 2.1.3 Burst Cycles . . . . . . . . . . . . . . . . . . 2.2 Chip-Select Module . . . . . . . . . . . . . ... .. ... ... ... .. . . . . . . ...... ..... ....... ....... ....... ..... . . . . . . ....... ...... ........ ........ ........ ...... .8 .8 .8 .8 .9 10 3 S1D13A04 Host Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.1 Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . 11 3.2 Host Bus Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . 12 MCF5307 To S1D13A04 Interface . . 4.1 Hardware Description . . . . . . 4.2 S1D13A04 Hardware Configuration 4.3 Register/Memory Mapping . . . . 4.4 MCF5307 Chip Select Configuration . . . . . ... .. .. .. .. . . . . . . . . . . . . . . . ... .. .. .. .. . . . . . . . . . . . . . . . ... .. .. .. .. . . . . . . . . . . . . . . . ... .. .. .. .. . . . . . . . . . . . . . . . 13 13 14 15 15 4 5 6 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 6.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 7.1 EPSON LCD/USB Companion Chips (S1D13A04) . . . . . . . . . . . . . . . 18 7.2 Motorola MCF5307 Processor . . . . . . . . . . . . . . . . . . . . . . . . 18 7 Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-010-01 Page 4 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-010-01 Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 5 List of Tables Table 3-1: Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Table 4-1: Summary of Power-On/Reset Options . . . . . . . . . . . . . . . . . . . . . . . . . . 14 List of Figures Figure 2-1: Figure 2-2: Figure 2-3: Figure 4-1: MCF5307 Memory Read Cycle . . . . . . . . . . . . . . . . MCF5307 Memory Write Cycle . . . . . . . . . . . . . . . . Chip Select Module Outputs Timing . . . . . . . . . . . . . Typical Implementation of MCF5307 to S1D13A04 Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 .9 . 10 . 13 Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-010-01 Page 6 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-010-01 Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 7 1 Introduction This application note describes the hardware and software environment required to interface the S1D13A04 LCD/USB Companion Chip and the Motorola MCF5307 "Coldfire" Processor. The designs described in this document are presented only as examples of how such interfaces might be implemented. This application note is updated as appropriate. Please check the Epson Research and Development website at www.erd.epson.com for the latest revision of this document before beginning any development. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-010-01 Page 8 Epson Research and Development Vancouver Design Center 2 Interfacing to the MCF5307 2.1 The MCF5307 System Bus The MCF5200/5300 family of processors feature a high-speed synchronous system bus typical of modern microprocessors. This section is an overview of the operation of the CPU bus in order to establish interface requirements. 2.1.1 Overview The MCF5307 microprocessor family uses a synchronous address and data bus, very similar in architecture to the MC68040 and MPC8xx. All outputs and inputs are timed with respect to a square-wave reference clock called BCLK0 (Master Clock). This clock runs at a software-selectable divisor rate from the machine cycle speed of the CPU core (typically 20 to 33 MHz). Both the address and the data bus are 32 bits in width. All IO accesses are memory-mapped; there is no separate IO space in the Coldfire architecture. The bus can support two types of cycles, normal and burst. Burst memory cycles are used to fill on-chip cache memories, and for certain on-chip DMA operations. Normal cycles are used for all other data transfers. 2.1.2 Normal (Non-Burst) Bus Transactions A data transfer is initiated by the bus master by placing the memory address on address lines A31 through A0 and driving TS (Transfer Start) low for one clock cycle. Several control signals are also provided with the memory address: * SIZ[1:0] (Transfer Size) -- indicates whether the bus cycle is 8, 16, or 32-bit. * R/W -- set high for read cycles and low for write cycles. * TT[1:0] (Transfer Type Signals) -- provides more detail on the type of transfer being attempted. * TIP (Transfer In Progress) -- asserts whenever a bus cycle is active. When the peripheral device being accessed has completed the bus transfer, it asserts TA (Transfer Acknowledge) for one clock cycle to complete the bus transaction. Once TA has been asserted, the MCF5307 will not start another bus cycle until TA has been de-asserted. The minimum length of a bus transaction is two bus clocks. S1D13A04 X37A-G-010-01 Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 9 Figure 2-1: "MCF5307 Memory Read Cycle," illustrates a typical memory read cycle on the MCF5307 system bus. BCLK0 TS TA TIP A[31:0] R/W SIZ[1:0], TT[1:0] D[31:0] Transfer Start Wait States Transfer Complete Sampled when TA low Next Transfer Starts Figure 2-1: MCF5307 Memory Read Cycle Figure 2-2: "MCF5307 Memory Write Cycle," illustrates a typical memory write cycle on the MCF5307 system bus. BCLK0 TS TA TIP A[31:0] R/W SIZ[1:0], TT[1:0] D[31:0] Transfer Start Valid Wait States Transfer Complete Next Transfer Starts Figure 2-2: MCF5307 Memory Write Cycle 2.1.3 Burst Cycles Burst cycles are very similar to normal cycles, except that they occur as a series of four back-to-back, 32-bit memory reads or writes. The TIP (Transfer In Progress) output is asserted continuously through the burst. Burst memory cycles are mainly intended to fill Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-010-01 Page 10 Epson Research and Development Vancouver Design Center caches from program or data memory. They are typically not used for transfers to or from IO peripheral devices such as the S1D13A04. The MCF5307 chip selects provide a mechanism to disable burst accesses for peripheral devices which are not burst capable. 2.2 Chip-Select Module In addition to generating eight independent chip-select outputs, the MCF5307 Chip Select Module can generate active-low Output Enable (OE) and Write Enable (BWE) signals compatible with most memory and x86-style peripherals. The MCF5307 bus controller also provides a Read/Write (R/W) signal which is compatible with most 68K peripherals. Chip selects 0 and 1 can be programmed independently to respond to any base address and block size. Chip select 0 can be active immediately after reset, and is typically used to control a boot ROM. Chip select 1 is likewise typically used to control a large static or dynamic RAM block. Chip selects 2 through 7 have fixed block sizes of 2M bytes each. Each has a unique, fixed offset from a common, programmable starting address. These chip selects are well-suited to typical IO addressing requirements. Each chip select may be individually programmed for: * port size (8/16/32-bit). * up to 15 wait states or external acknowledge. * address space type. * burst or non-burst cycle support. * write protect. Figure 2-3: "Chip Select Module Outputs Timing" illustrates a typical cycle for a memory mapped device using the GPCM of the Power PC. CLK CS[7:0] BE/BWE[3:0] OE Figure 2-3: Chip Select Module Outputs Timing S1D13A04 X37A-G-010-01 Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 11 3 S1D13A04 Host Bus Interface The S1D13A04 directly supports multiple processors. The S1D13A04 implements a 16-bit Generic #1 Host Bus Interface which is most suitable for direct connection to the Motorola MFC5307 microprocessor. Generic #1 supports a Chip Select and an individual Read Enable/Write Enable for each byte. The Generic #1 Host Bus Interface is selected by the S1D13A04 on the rising edge of RESET#. After RESET# is released, the bus interface signals assume their selected configuration. For details on the S1D13A04 configuration, see Section 4.2, "S1D13A04 Hardware Configuration" on page 14. 3.1 Host Bus Interface Pin Mapping The following table shows the functions of each Host Bus Interface signal. Table 3-1: Host Bus Interface Pin Mapping S1D13A04 Pin Names AB[17:0] DB[15:0] WE1# CS# M/R# CLKI BS# RD/WR# RD# WE0# WAIT# RESET# Motorola MCF5307 A[17:0] D[31:16] BWE1 CS4 A18 BCLK0 Connect to IOVDD from the S1D13A04 OE OE BWE0 TA system RESET Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-010-01 Page 12 Epson Research and Development Vancouver Design Center 3.2 Host Bus Interface Signals The Host Bus Interface requires the following signals. * CLKI is a clock input which is required by the S1D13A04 Host Bus Interface as a source for its internal bus and memory clocks. This clock is typically driven by the host CPU system clock. For this example, BCLK0 from the Motorola MCF5307 is used for CLKI. * The address inputs AB[17:0] connect directly to the MCF5307 address bus (A[17:0]). * DB[7:0] connects D[23:16] (the MCF5307 low order byte). DB[15:8] connects to D[31:24] (the MCF5307 high order byte). CNF4 must be set to select big endian mode. * Chip Select (CS#) must be driven low by CS4 whenever the S1D13A04 is accessed by the Motorola MCF5307. * M/R# (memory/register) selects between memory or register accesses. This signal is generated by the external address decode circuitry. For this example, M/R# is connected to address line A18, allowing system address A18 to select between memory or register accesses. * WE0# connects to BWE0 (the low byte enable signal from the MCF5307) and must be driven low when the MCF5307 is writing the low byte to the S1D13A04. * WE1# connects to BWE1 (the high byte enable signal from the MCF5307) and must be driven low when the MCF5307 is writing the high byte to the S1D13A04. * RD# and RD/WR# are read enables for the low-order and high-order bytes, respectively. Both signals are driven low by OE when the Motorola MCF5307 is reading data from the S1D13A04. * WAIT# connects to TA and is a signal which is output from the S1D13A04 that indicates the host CPU must wait until data is ready (read cycle) or accepted (write cycle) on the host bus. Since host CPU accesses to the S1D13A04 may occur asynchronously to the display update, it is possible that contention may occur in accessing the S1D13A04 internal registers and/or refresh memory. The WAIT# line resolves these contentions by forcing the host to wait until the resource arbitration is complete. This signal is active low and may need to be inverted if the host CPU wait state signal is active high. * The Bus Status (BS#) signal is not used in the bus interface for Generic #1 mode and must be tied high to IO VDD. S1D13A04 X37A-G-010-01 Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 13 4 MCF5307 To S1D13A04 Interface 4.1 Hardware Description The interface between the S1D13A04 and the MCF5307 requires no external glue logic. The polarity of the WAIT# signal must be selected as active high by connecting CNF5 to IO VDD (see Table 4-1:, "Summary of Power-On/Reset Options," on page 14). The following diagram shows a typical implementation of the MCF5307 to S1D13A04 interface. S1D13A04 AB[17:0] DB[7:0] DB[15:8] M/R# CS# IO VDD MCF5307 A[17:0] D[23:16] D[31:24] A18 CS4 BS# TA BWE1 BWE0 OE WAIT# WE1# WE0# RD/WR# RD# BCLK0 System RESET CLKI RESET# Note: When connecting the S1D13A04 RESET# pin, the system designer should be aware of all conditions that may reset the S1D13A04 (e.g. CPU reset can be asserted during wake-up from power-down modes, or during debug states). Figure 4-1: Typical Implementation of MCF5307 to S1D13A04 Interface Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-010-01 Page 14 Epson Research and Development Vancouver Design Center 4.2 S1D13A04 Hardware Configuration The S1D13A04 uses CNF6 through CNF0 to allow selection of the bus mode and other configuration data on the rising edge of RESET#. For details on configuration, refer to the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. The following table shows the configuration required for this implementation of a S1D13A04 to Motorola MFC5307 microprocessor. Table 4-1: Summary of Power-On/Reset Options S1D13A04 Configuration Input CNF4, CNF[2:0] CNF3 CNF5 CNF6 Power-On/Reset State 1 (connected to IO VDD) Select host bus interface as follows: CNF4 1 CNF2 0 CNF1 1 CNF0 1 Host Bus Generic #1, Big Endian WAIT# is active low CLKI to BCLK divide ratio 1:1 0 (connected to VSS) Reserved. Must be set to 1. WAIT# is active high CLKI to BCLK divide ratio 2:1 configuration for Motorola MFC5307 microprocessor S1D13A04 X37A-G-010-01 Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 15 4.3 Register/Memory Mapping The S1D13A04 uses two 256K byte blocks which are selected using A18 from the MCF5307 (A18 is connected to the S1D13A04 M/R# pin). The internal registers occupy the first 256K bytes block and the 160K byte display buffer occupies the second 256K byte block. These two blocks of memory are aliased over the entire 2M byte space. Note If aliasing is not desirable, the upper addresses must be fully decoded. 4.4 MCF5307 Chip Select Configuration Chip Selects 0 and 1 have programmable block sizes from 64K bytes through 2G bytes. However, these chip selects would normally be needed to control system RAM and ROM. Therefore, one of the IO chip selects CS2 through CS7 is required to address the entire address space of the S1D13A04. These IO chip selects have a fixed, 2M byte block size. In the example interface, chip select 4 is used to control the S1D13A04. The CSBAR register should be set to the upper 8 bits of the desired base address. The following options should be selected in the chip select mask registers (CSMR4/5). * WP = 0 - disable write protect * AM = 0 - enable alternate bus master access to the S1D13A04 * C/I = 1 - disable CPU space access to the S1D13A04 * SC = 1 - disable Supervisor Code space access to the S1D13A04 * SD = 0 - enable Supervisor Data space access to the S1D13A04 * UC = 1 - disable User Code space access to the S1D13A04 * UD = 0 - enable User Data space access to the S1D13A04 * V = 1 - global enable ("Valid") for the chip select The following options should be selected in the chip select control registers (CSCR4/5). * WS0-3 = 0 - no internal wait state setting * AA = 0 - no automatic acknowledgment * PS (1:0) = 1:0 - memory port size is 16 bits * BEM = 0 - Byte enable/write enable active on writes only * BSTR = 0 - disable burst reads * BSTW = 0 - disable burst writes Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-010-01 Page 16 Epson Research and Development Vancouver Design Center 5 Software Test utilities and display drivers are available for the S1D13A04. Full source code is available for both the test utilities and the drivers. The test utilities are configurable for different panel types using a program called 13A04CFG (see document number X37A-B-001-xx), or by directly modifying the source. The display drivers can be customized by the OEM for different panel types, resolutions and color depths only by modifying the source. The S1D13A04 test utilities and display drivers are available from your sales support contact (see Section 7, "Sales and Technical Support") or www.erd.epson.com. S1D13A04 X37A-G-010-01 Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 17 6 References 6.1 Documents * Motorola Inc., MCF5307 ColdFire(R) Integrated Microprocessor User's Manual, Motorola Publication no. MCF5307UM; available on the Internet at http://www.mot.com/SPS/HPESD/prod/coldfire/5307UM.html. * Epson Research and Development, Inc., S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. * Epson Research and Development, Inc., S5U13A04B00C Rev. 1.0 Evaluation Board User Manual, document number X37A-G-004-xx. * Epson Research and Development, Inc., S1D13A04 Programming Notes and Examples, document number X37A-G-003-xx. 6.2 Document Sources * Motorola Inc.: Motorola Literature Distribution Center, (800) 441-2447. * Motorola Inc. Website: www.mot.com. * Epson Research and Development Website: www.erd.epson.com. Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-010-01 Page 18 Epson Research and Development Vancouver Design Center 7 Sales and Technical Support 7.1 EPSON LCD/USB Companion Chips (S1D13A04) Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk/ Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de 7.2 Motorola MCF5307 Processor * Motorola Design Line, (800) 521-6274. * Local Motorola sales office or authorized distributor. S1D13A04 X37A-G-010-01 Interfacing to the Motorola MCF5307 "ColdFire" Microprocessor Issue Date: 01/10/12 S1D13A04 LCD/USB Companion Chip Connecting to the Sharp HR-TFT Panels Document Number: X37A-G-011-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All other trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-011-01 Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 3 Table of Contents 1 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Connecting to the Sharp LQ039Q2DS01 HR-TFT . 2.1 External Power Supplies . . . . . . . . . . . 2.1.1 Gray Scale Voltages for Gamma Correction . 2.1.2 Digital/Analog Power Supplies . . . . . . . . 2.1.3 DC Gate Driver Power Supplies . . . . . . . 2.1.4 AC Gate Driver Power Supplies . . . . . . . 2.2 HR-TFT MOD Signal . . . . . . . . . . . . 2.3 S1D13A04 to LQ039Q2DS01 Pin Mapping . . . Connecting to the Sharp LQ031B1DDxx HR-TFT . 3.1 External Power Supplies . . . . . . . . . . . 3.1.1 Gray Scale Voltages for Gamma Correction . 3.1.2 Digital/Analog Power Supplies . . . . . . . . 3.1.3 DC Gate Driver Power Supplies . . . . . . . 3.1.4 AC Gate Driver Power Supplies . . . . . . . 3.2 HR-TFT MOD Signal . . . . . . . . . . . . 3.3 S1D13A04 to LQ031B1DDxx Pin Mapping . . . ... .. ... ... ... ... .. .. ... .. ... ... ... ... .. .. . . . . . . . . . . . . . . . . ...... ..... ....... ....... ....... ....... ..... ..... ...... ..... ....... ....... ....... ....... ..... ..... . . . . . . . . . . . . . . . . ....... ...... ........ ........ ........ ........ ...... ...... ....... ...... ........ ........ ........ ........ ...... ...... .8 .8 .8 .9 .9 10 11 12 14 14 14 15 15 15 15 16 3 4 5 Test Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 5.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 5.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6.1 EPSON LCD/USB Companion Chips (S1D13A04) . . . . . . . . . . . . . . . 20 6.2 Sharp HR-TFT Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 6 Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 S1D13A04 X37A-G-011-01 Page 4 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-011-01 Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 5 List of Tables Table 2-1: HR-TFT Power-On/Off Sequence Timing . . . . . . . . . . . . . . . . . . . . . . . . . 11 Table 2-2: S1D13A04 to LQ039Q2DS01 Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . 12 Table 3-1: S1D13A04 to LQ031B1DDxx Pin Mapping. . . . . . . . . . . . . . . . . . . . . . . . 16 List of Figures Figure 2-1: Figure 2-2: Figure 2-3: Figure 2-4: Figure 3-1: Sharp LQ039Q2DS01 Gray Scale Voltage (V0-V9) Generation Panel Gate Driver DC Power Supplies . . . . . . . . . . . . . . Panel Gate Driver AC Power Supplies . . . . . . . . . . . . . . HR-TFT Power-On/Off Sequence Timing . . . . . . . . . . . . Sharp LQ031B1DDxx Gray Scale Voltage (V0-V9) Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 .9 . 10 . 11 . 14 Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 S1D13A04 X37A-G-011-01 Page 6 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-011-01 Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 7 1 Introduction This application note describes the hardware and software environment required to connect to the Sharp HR-TFT panels directly supported by the S1D13A04. These panels are: * Sharp LQ031B1DDXX 160 x 160 HR-TFT panel. * Sharp LQ039Q2DS01 320 x 240 HR-TFT panel. The designs described in this document are presented only as examples of how such interfaces might be implemented. This application note is updated as appropriate. Please check the Epson Research and Development website at www.erd.epson.com for the latest revision of this document before beginning any development. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 S1D13A04 X37A-G-011-01 Page 8 Epson Research and Development Vancouver Design Center 2 Connecting to the Sharp LQ039Q2DS01 HR-TFT 2.1 External Power Supplies The S1D13A04 provides all necessary data and control signals to connect to the Sharp LQ039Q2DS01 320 x 240 HR-TFT panel. However, it does not provide any of the voltages required for gray scaling, gate driving, or for the digital and analog supplies. Therefore, external supplies must be designed for any device utilizing the LQ039Q2DS01. 2.1.1 Gray Scale Voltages for Gamma Correction The standard gray scale voltages can be generated using a precise resistor divider network that supplies two sets (A and B) of nine reference voltages to a National Semiconductor 9-Channel Buffer Amplifier (LMC6009). The LMC6009 buffers these nine reference voltages and outputs them to the panel column drivers. The A/B inputs allow the two sets of reference voltages to be alternated, compensating for asymmetrical gamma characteristics during row inversion. This input is controlled by the S1D13A04 output signal REV which toggles every time a horizontal sync signal is sent to the panel. The REV signal is also used to generate the highest gray scale voltage (V0 or black) by buffering REV and shifting its maximum level to the maximum gray scale voltage (CON_POWER). CON_POWER is supplied by a National Semiconductor micropower Voltage Regulator (LP2951). Figure 2-1: "Sharp LQ039Q2DS01 Gray Scale Voltage (V0V9) Generation" shows the schematic for gray scale voltage generation. 47.5K 1% 47.5K 1% 47.5K 1% 47.5K 1% 47.5K 1% 47.5K 1% 47.5K 1% 47.5K 1% 47.5K 1% CON_POWER U1 1 2 3 A1A A1B A2A A2B A3A A3B A4A A4B A5A A5B A6A A6B A7A A7B A8A A8B A9A A9B 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 NC11 NC13 NC14 NC7 NC8 NC9 NC10 NC12 OUT_A1 OUT_A2 OUT_A3 OUT_A4 OUT_A5 OUT_A6 OUT_A7 OUT_A8 OUT_A9 AB_Switch 45 47 48 25 26 27 28 46 V[9:1] 42 41 40 39 36 35 34 33 32 29 L1 V1 V2 V3 V4 V5 V6 V7 V8 V9 V0 0.1uH +5V V[9:1] R1 R2 R3 R4 R5 R6 R7 R8 R9 NC1 NC2 NC3 A1A A1B A2A A2B A3A A3B A4A A4B A5A A5B A6A A6B A7A A7B A8A A8B A9A A9B 6.04K 1% 14.3K 1% 22.6K 1% 28.7K 1% 34.0K 1% 42.2K 1% 52.3K 1% 75.0K 1% R10 R11 R12 R13 R14 R15 R16 R17 R18 93.1K 1% A9A A8A A7A A6A A5A A4A A3A A2A A1A 47.5K 1% 47.5K 1% 47.5K 1% 47.5K 1% 47.5K 1% 47.5K 1% 47.5K 1% 47.5K 1% 47.5K 1% R19 R20 R21 R22 R23 R24 R26 R25 R27 22 23 24 VCC1 VCC2 VCC3 GNDA GNDB GNDC 44 38 30 43 37 31 NC4 NC5 NC6 C1 0.1uF A9B R28 A8B R29 A7B R30 A6B R31 A5B R32 A4B R33 A3B R34 A2B R35 R36 A1B +5V U2 8 7 6 5 LMC6009 90.9K 1% 53.6K 1% 41.1K 1% 33.2K 1% 25.3K 1% 19.6K 1% 11.8K 1% 5.36K 1% 178K 1% R37 11.8K 1% VIN FEEDBACK VTAP ERROR LP2951 OUTPUT SENSE SHTDWN GND 1 2 3 4 CON_POWER + C2 C3 0.1uF 220uF 25V R38 5.38K 1% +5V R39 REV 180 74ACT04 CON_POWER U3A 14 1 7 2 +5V U3B 14 3 7 74ACT04 4 1 2 3 4 U4 N-S N-G P-S P-G F2C02E N-D1 N-D2 P-D1 P-D2 5 6 7 8 V0 Figure 2-1: Sharp LQ039Q2DS01 Gray Scale Voltage (V0-V9) Generation S1D13A04 X37A-G-011-01 Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 9 2.1.2 Digital/Analog Power Supplies The digital power supply (VSHD) must be connected to a 3.3V supply. The analog power supply (VSHA) must be connected to a 5.0V supply. 2.1.3 DC Gate Driver Power Supplies The gate driver high level power supply (VDD) and the gate driver logic low power supply (VSS) have typical values of +15V and -15V respectively. These power supplies can be provided by a Linear Technology high efficiency switching regulator (LT1172). The two power supplies can be adjusted through their allowable ranges using the potentiometer VR1. The gate driver logic high power supply (VCC) is defined as VSS + VSHD. The typical VCC voltage of -11.7V can be supplied from VSS using a 3.3V zener diode which provides the necessary voltage change. Figure 2-2: "Panel Gate Driver DC Power Supplies" shows the schematic for VSS, VDD and VCC. +5V L1 D1 SCHOTTKY 1A Vf=0.5V 2 1 3 VDD VR1 2 20K R2 1K 5% 1 2 D2 2 VSS VSS 1 100uH 300mA 1K 5% R1 U1 5 2 1 6 8 Vin Vswitch Vcomp Vfb Gnd E1 E2 LT1172 7 3 C3 N/C 4 22uF 16V D3 SCHOTTKY + C1 10uF 25V C2 1uF + D4 VSS 2 1 3.3V Zener VCC R3 22K 5% Figure 2-2: Panel Gate Driver DC Power Supplies Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 1 + SCHOTTKY C4 10uF 16V S1D13A04 X37A-G-011-01 Page 10 Epson Research and Development Vancouver Design Center 2.1.4 AC Gate Driver Power Supplies The gate drive low level power supply (VEE) is an AC power supply with a DC offset voltage (offset typically -9.0V). The AC component is the common electrode driving signal (VCOM) which has a voltage of 2.5V. VCOM must be alternated every horizontal period and every vertical period. The S1D13A04 output signal REV accomplishes this function and generates the alternating VCOM signal which is superimposed onto VEE. Figure 2-3: "Panel Gate Driver AC Power Supplies," on page 10 shows the schematic for generating VCOM and VEE. +5V R1 REV 180 U1A 14 1 7 74ACT04 2 1 2 3 4 U2 N-S N-G P-S P-G F2C02E N-D1 N-D2 P-D1 P-D2 5 6 7 8 + C1 22uF 16V R3 22 5% VSS R2 15K 5% R4 VEE +5V + 3 C2 22uF 16V 27K 5% 3 R5 VR1 100K 1 2 1 Q1 2 NPN 2 12K 5% VCOM R6 22 5% 1 C3 0.1uF R7 120K 5% Q2 3 PNP Figure 2-3: Panel Gate Driver AC Power Supplies S1D13A04 X37A-G-011-01 Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 11 2.2 HR-TFT MOD Signal The HR-TFT panel uses an input signal (MOD) to control the power-on sequencing of the panel. This HR-TFT signal should not be confused with the S1D13A04 signal DRDY (referred to as MOD for passive panels). To power-on the HR-TFT panel, MOD must be held low until the power supply has been turned on for more than two FRAMES. To power-off the HR-TFT panel, MOD must be forced low before the power supply is turned off. This sequencing requires two software controlled GPIO pins from the S1D13A04 (see Figure 2-4: "HR-TFT Power-On/Off Sequence Timing" ). t1 GPIOx* (VSHD power) GPIOy** (other power) GPO (MOD) Power Save Mode Enable*** (REG[A0h] bit 0) t2 t3 t4 t5 t6 t7 Active t8 LCD Signals**** *It is recommended to use one of the general purpose IO pins GPIO[6:4] to control the digital power supply VSHD. **It is recommended to use one of the general purpose IO pins GPIO[6:4] to control the other power supplies required by the HR-TFT panel. ***The S1D13A04 LCD power-on/off sequence is activated by programming the Power Save Mode Enable bit (REG[A0h] bit 0) ****LCD Signals include: FPDAT[17:0], FPSHIFT, FPLINE, FPFRAME, and GPIO[3:0]. Figure 2-4: HR-TFT Power-On/Off Sequence Timing Table 2-1: HR-TFT Power-On/Off Sequence Timing Symbol t1 t2 t3 t4 t5 t6 t7 t8 Parameter LCD Power (VSHD) active to Power Save Mode disabled LCD signals low to LCD Power (VSHD) inactive Power Save Mode disabled to LCD Power (other) active LCD Power (other) inactive to Power Save Mode enabled LCD Power (other) active to MOD active MOD inactive to LCD Power (other) inactive Power Save Mode disabled to LCD signals active Power Save Mode enabled to LCD signals low Min 0 0 0 0 2 0 20 20 Max Units ns ns ns ns FRAME ns ns ns Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 S1D13A04 X37A-G-011-01 Page 12 Epson Research and Development Vancouver Design Center 2.3 S1D13A04 to LQ039Q2DS01 Pin Mapping Table 2-2: S1D13A04 to LQ039Q2DS01 Pin Mapping LCD Pin LCD Pin No. Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 VDD VCC MOD MOD U/L SPS CLS VSS VEE VEE VCOM VCOM SPL R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 S1D13A04 Pin Name FPFRAME GPIO1 GPIO3 FPDAT11 FPDAT10 FPDAT9 FPDAT2 FPDAT1 FPDAT0 FPDAT14 FPDAT13 FPDAT12 FPDAT5 FPDAT4 FPDAT3 Description Power supply of gate driver (high level) Power supply of gate driver (logic high) Control signal of gate driver Control signal of gate driver Selection for vertical scanning direction Start signal of gate driver Clock signal of gate driver Power supply of gate driver (logic low) Power supply of gate driver (low level) Power supply of gate driver (low level) Common electrode driving signal Common electrode driving signal Sampling start signal for left / right scanning Red data signal (LSB) Red data signal Red data signal Red data signal Red data signal Red data signal (MSB) Green data signal (LSB) Green data signal Green data signal Green data signal Green data signal Green data signal (MSB) See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 Remarks See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 See Section 2.2, "HR-TFT MOD Signal" on page 11 See Section 2.2, "HR-TFT MOD Signal" on page 11 Connect to VSHD (top / bottom scanning) S1D13A04 X37A-G-011-01 Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 13 Table 2-2: S1D13A04 to LQ039Q2DS01 Pin Mapping (Continued) LCD Pin LCD Pin No. Name 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 B0 B1 B2 B3 B4 B5 VSHD DGND PS LP DCLK LBR SPR VSHA V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 AGND S1D13A04 Pin Name FPDAT17 FPDAT16 FPDAT15 FPDAT8 FPDAT7 FPDAT6 VSS GPIO0 FPLINE FPSHIFT VSS Description Blue data signal (LSB) Blue data signal Blue data signal Blue data signal Blue data signal Blue data signal (MSB) Digital power supply Digital ground Power save signal Data latch signal of source driver Data sampling clock signal Selection for horizontal scanning direction Sampling start signal for right / left scanning Analog power supply Standard gray scale voltage (black) Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage (white) Analog ground Connect to VSHD (left / right scanning) Right to left scanning not supported See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 See Section 2.1, "External Power Supplies" on page 8 Ground pin of S1D13A04 See Section 2.1, "External Power Supplies" on page 8 Ground pin of S1D13A04 Remarks Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 S1D13A04 X37A-G-011-01 Page 14 Epson Research and Development Vancouver Design Center 3 Connecting to the Sharp LQ031B1DDxx HR-TFT 3.1 External Power Supplies The S1D13A04 provides all necessary data and control signals to connect to the Sharp LQ031B1DDxx 160x160 HR-TFT panel(s). However, it does not provide any of the voltages required for the backlight, gray scaling, gate driving, or for the digital and analog supplies. Therefore, external supplies must be designed for any device utilizing the LQ031B1DDxx. The LQ031B1DDxx (160x160) has the same voltage requirements as the LQ039Q2DS01 (320x240). All the circuits used to generate the various voltages for the LQ039Q2DS01 panel also apply to the LQ031B1DDxx panel. This section provides additional circuits for generating some of these voltages. 3.1.1 Gray Scale Voltages for Gamma Correction The standard gray scale voltages can be generated using a precise resistor divider network as described in Section 2.1.1, "Gray Scale Voltages for Gamma Correction" on page 8. Alternately, they can be generated using a Sharp gray scale IC. The Sharp IR3E203 eliminates the large resistor network used to provide the 10 gray scale voltages and combines their function into a single IC. The S1D13A04 output signal REV is used to alternate the gray scale voltages and connects to the SW input of the IR3E203 IC. The COM signal is used in generating the gate driver panel AC voltage, VCOM and is explained in Section 3.1.4, "AC Gate Driver Power Supplies" on page 15. Figure 3-1: "Sharp LQ031B1DDxx Gray Scale Voltage (V0-V9) Generation" shows the circuit that generates the gray scale voltages using the Sharp IR3E203 IC. 5V C1 4.7uF U1 3 2 C2 2.2uF V[9:0] 5 6 7 8 9 11 12 13 14 15 4 V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 COM VCC REV 16 1 17 18 10 V0 V1 SW V2 V3 V4 NC V5 NC V6 NC V7 GND V8 V9 COM SHARP IR3E203 Figure 3-1: Sharp LQ031B1DDxx Gray Scale Voltage (V0-V9) Generation S1D13A04 X37A-G-011-01 VDD Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 15 3.1.2 Digital/Analog Power Supplies The digital power supply (VSHD) must be connected to a 3.3V supply. The analog power supply (VSHA) must be connected to a 5.0V supply. 3.1.3 DC Gate Driver Power Supplies See Section 2.1.3, "DC Gate Driver Power Supplies" on page 9 and Figure 2-2: "Panel Gate Driver DC Power Supplies," on page 9 for details on generating VSS, VDD, and VCC. 3.1.4 AC Gate Driver Power Supplies See Section 2.1.4, "AC Gate Driver Power Supplies" on page 10 and Figure 2-3: "Panel Gate Driver AC Power Supplies," on page 10 for details on generating VEE and VCOM. If the Sharp IR3E203 is used to generate the gray scale voltages, the COM signal can be connected to the input of the F2C02E MOSFET instead of the buffered REV signal. 3.2 HR-TFT MOD Signal See Section 2.2, "HR-TFT MOD Signal" on page 11 for details on controlling the MOD signal through software. Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 S1D13A04 X37A-G-011-01 Page 16 Epson Research and Development Vancouver Design Center 3.3 S1D13A04 to LQ031B1DDxx Pin Mapping Table 3-1: S1D13A04 to LQ031B1DDxx Pin Mapping LCD Pin LCD Pin No. Name 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 VDD VCC MOD MOD U/L SPS CLS VSS VEE VEE VCOM VCOM SPL R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 S1D13A04 Pin Name FPFRAME GPIO1 GPIO3 FPDAT11 FPDAT10 FPDAT9 FPDAT2 FPDAT1 FPDAT0 FPDAT14 FPDAT13 FPDAT12 FPDAT5 FPDAT4 FPDAT3 Description Power supply of gate driver (high level) Power supply of gate driver (logic high) Control signal of gate driver Control signal of gate driver Selection for vertical scanning direction Start signal of gate driver Clock signal of gate driver Power supply of gate driver (logic low) Power supply of gate driver (low level) Power supply of gate driver (low level) Common electrode driving signal Common electrode driving signal Sampling start signal for left / right scanning Red data signal (LSB) Red data signal Red data signal Red data signal Red data signal Red data signal (MSB) Green data signal (LSB) Green data signal Green data signal Green data signal Green data signal Green data signal (MSB) See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 Remarks See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 See Section 3.2, "HR-TFT MOD Signal" on page 15 See Section 3.2, "HR-TFT MOD Signal" on page 15 Connect to VSHD (top / bottom scanning) S1D13A04 X37A-G-011-01 Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 17 Table 3-1: S1D13A04 to LQ031B1DDxx Pin Mapping (Continued) LCD Pin LCD Pin No. Name 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 B0 B1 B2 B3 B4 B5 VSHD DGND PS LP DCLK LBR SPR VSHA V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 AGND S1D13A04 Pin Name FPDAT17 FPDAT16 FPDAT15 FPDAT8 FPDAT7 FPDAT6 VSS GPIO0 FPLINE FPSHIFT VSS Description Blue data signal (LSB) Blue data signal Blue data signal Blue data signal Blue data signal Blue data signal (MSB) Digital power supply Digital ground Power save signal Data latch signal of source driver Data sampling clock signal Selection for horizontal scanning direction Sampling start signal for right / left scanning Analog power supply Standard gray scale voltage (black) Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage Standard gray scale voltage (white) Analog ground Connect to VSHD (left / right scanning) Right to left scanning not supported See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 See Section 3.1, "External Power Supplies" on page 14 Ground pin of S1D13A04 See Section 3.1, "External Power Supplies" on page 14 Ground pin of S1D13A04 Remarks Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 S1D13A04 X37A-G-011-01 Page 18 Epson Research and Development Vancouver Design Center 4 Test Software Test utilities and display drivers are available for the S1D13A04. Full source code is available for both the test utilities and the drivers. The test utilities are configurable for different panel types using a program called 13A04CFG (see document number X37A-B-001-xx), or by directly modifying the source. The display drivers can be customized by the OEM for different panel types, resolutions and color depths only by modifying the source. The S1D13A04 test utilities and display drivers are available from your sales support contact (see Section 6, "Sales &Technical Support") or at www.erd.epson.com. S1D13A04 X37A-G-011-01 Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 19 5 References 5.1 Documents * Sharp Electronics Corporation, LQ039Q2DS01 Specification. * Sharp Electronics Corporation, LQ031B1DDxx Specification. * Epson Research and Development, Inc., S1D13A04 Hardware Functional Specification, Document Number X37A-A-001-xx. * Epson Research and Development, Inc., S1D13A04 Programming Notes and Examples, Document Number X37A-G-003-xx. * Epson Research and Development, Inc., S5U13A04B00C Rev. 1.0 ISA Bus Evaluation Board User Manual, Document Number X37A-G-004-xx. 5.2 Document Sources * Sharp Electronics Corporation Website: www.sharpmeg.com. * Epson Research and Development Website: www.erd.epson.com. Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 S1D13A04 X37A-G-011-01 Page 20 Epson Research and Development Vancouver Design Center 6 Sales &Technical Support 6.1 EPSON LCD/USB Companion Chips (S1D13A04) Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk/ Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de 6.2 Sharp HR-TFT Panel http://www.sharpmeg.com S1D13A04 X37A-G-011-01 Connecting to the Sharp HR-TFT Panels Issue Date: 01/10/12 S1D13A04 LCD/USB Companion Chip Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Document Number: X37A-G-012-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All Trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-012-01 Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 3 Table of Contents 1 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Interfacing to the MC68VZ328 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.1 The MC68VZ328 System Bus . . . . . . . . . . . . . . . . . . . . . . . . . 8 2.2 Chip-Select Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 S1D13A04 Host Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 3.1 Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . 9 3.2 Host Bus Interface Signals . . . . . . . . . . . . . . . . . . . . . . . . . 10 MC68VZ328 to S1D13A04 Interface . . . . . . . . . . . 4.1 Hardware Description . . . . . . . . . . . . . . 4.2 S1D13A04 Hardware Configuration . . . . . . . . 4.2.1 Register/Memory Mapping . . . . . . . . . . . . . 4.2.2 MC68VZ328 Chip Select and Pin Configuration . . . . . . . ...... ..... ..... ....... ....... . . . . . ....... ...... ...... ........ ........ 11 11 12 13 13 3 4 5 6 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 6.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 7.1 EPSON LCD/USB Companion Chips (S1D13A04) . . . . . . . . . . . . . . . 16 7.2 Motorola MC68VZ328 Processor . . . . . . . . . . . . . . . . . . . . . . . 16 7 Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-012-01 Page 4 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-012-01 Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 5 List of Tables Table 3-1: Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Table 4-1: Summary of Power-On/Reset Options . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Table 4-2: WS Bit Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 List of Figures Figure 4-1: Typical Implementation of MC68VZ328 to S1D13A04 Interface . . . . . . . . . . . . 11 Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-012-01 Page 6 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-012-01 Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 7 1 Introduction This application note describes the hardware and software environment required to interface the S1D13A04 LCD/USB Companion Chip and the Motorola MC68VZ328 Dragonball VZ microprocessor. The designs described in this document are presented only as examples of how such interfaces might be implemented. This application note is updated as appropriate. Please check the Epson Research and Development website at www.erd.epson.com for the latest revision of this document before beginning any development. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-012-01 Page 8 Epson Research and Development Vancouver Design Center 2 Interfacing to the MC68VZ328 2.1 The MC68VZ328 System Bus The Motorola MC68VZ328 "Dragonball VZ" is the third generation in the Dragonball microprocessor family. The Dragonball VZ is an integrated controller designed for handheld products. It is based upon the FLX68000 microprocessor core and uses a 24-bit address bus and 16-bit data bus. The Dragonball VZ is faster than its predecessors and the DRAM controller now supports SDRAM. The bus interface consists of all the standard MC68000 bus interface signals except AS, plus some new signals intended to simplify the interface to typical memory and peripheral devices. The 68000 signals are multiplexed with IrDA, SPI and LCD controller signals. The MC68000 bus control signals are well documented in the Motorola user manuals, and are not be described here. The new signals are as follows. * Output Enable (OE) is asserted when a read cycle is in progress. It is intended to connect to the output enable control signal of a typical static RAM, EPROM, or Flash EPROM device. * Upper Write Enable and Lower Write Enable (UWE / LWE) are asserted during memory write cycles for the upper and lower bytes of the 16-bit data bus. They may be directly connected to the write enable inputs of a typical memory device. 2.2 Chip-Select Module The MC68VZ328 can generate up to 8 chip select outputs which are organized into four groups (A through D). Each chip select group has a common base address register and address mask register allowing the base address and block size of the entire group to be set. In addition, each chip select within a group has its own address compare and address mask register to activate the chip select for a subset of the group's address block. Each chip select may also be individually programmed to control an 8 or 16-bit device. Lastly, each chip select can either generate from 0 through 6 wait states internally, or allow the memory or peripheral device to terminate the cycle externally using the standard MC68000 DTACK signal. Chip select groups A and B are used to control ROM, SRAM, and Flash memory devices and have a block size of 128K bytes to 16M bytes. Chip select A0 is active immediately after reset and is a global chip select so it is typically used to control a boot EPROM device. A0 ceases to decode globally once its chip select registers are programmed. Groups C and D are special in that they can also control DRAM interfaces. These last two groups have block size of 32K bytes to 4M bytes. S1D13A04 X37A-G-012-01 Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 9 3 S1D13A04 Host Bus Interface The S1D13A04 directly supports multiple processors. The S1D13A04 implements a Dragonball Host Bus Interface which directly supports the Motorola MC68VZ328 microprocessor. The Dragonball Host Bus Interface is selected by the S1D13A04 on the rising edge of RESET#. After RESET# is released, the bus interface signals assume their selected configuration. For details on the S1D13A04 configuration, see Section 4.2, "S1D13A04 Hardware Configuration" on page 12. 3.1 Host Bus Interface Pin Mapping The following table shows the functions of each Host Bus Interface signal. Table 3-1: Host Bus Interface Pin Mapping S1D13A04 Pin Names AB[17:0] DB[15:0] WE1# CS# M/R# CLKI BS# RD/WR# RD# WE0# WAIT# RESET# Motorola MC68VZ328 A[17:0] D[15:0] UWE CSx External Decode CLKO Connect to IOVDD from the S1D13A04 Connect to IOVDD from the S1D13A04 OE LWE DTACK System RESET Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-012-01 Page 10 Epson Research and Development Vancouver Design Center 3.2 Host Bus Interface Signals The Host Bus Interface requires the following signals. * CLKI is a clock input required by the S1D13A04 Host Bus Interface as a source for its internal bus and memory clocks. This clock is typically driven by the host CPU system clock. For this example, CLK0 from the Motorola MC68VZ328 is used for CLKI. * The address inputs AB[17:0], and the data bus DB[15:0], connect directly to the MC68VZ328 address (A[17:0]) and data bus (D[15:0]), respectively. CNF4 must be set to one to select big endian mode. * Chip Select (CS#) must be driven low by one of the Dragonball VZ chip select outputs from the chip select module whenever the S1D13A04 is accessed by the MC68VZ328. * M/R# (memory/register) selects between memory or register accesses. This signal is generated by the external address decode circuitry. For this example, M/R# is connected to address line A18, allowing system address A18 to select between memory or register accesses. * WE0# connects to LWE (the low data byte write strobe enable of the MC68VZ328) and is asserted when valid data is written to the low byte of a 16-bit device. * WE1# connects to UWE (the upper data byte write strobe enable of the MC68VZ328) and is asserted when valid data is written to the high byte of a 16-bit device. * RD# connects to OE (the read output enable of the MC68VZ328) and is asserted during a read cycle of the MC68VZ328 microprocessor. * RD/WR# is not used for the Dragonball host bus interface and must be tied high to IO VDD. * WAIT# connects to DTACK and is a signal which is output from the S1D13A04 indicating the MC68VZ328 must wait until data is ready (read cycle) or accepted (write cycle) on the host bus. MC68VZ328 accesses to the S1D13A04 may occur asynchronously to the display update. * BS# is not used for the Dragonball host bus interface and must be tied high to IO VDD. S1D13A04 X37A-G-012-01 Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 11 4 MC68VZ328 to S1D13A04 Interface 4.1 Hardware Description The interface between the S1D13A04 and the MC68VZ328 does not requires any external glue logic. Chip select module B is used to provide the S1D13A04 with a chip select and A18 is used to select between memory and register accesses. In this example, the DTACK signal is made available for the S1D13A04. Alternately, the S1D13A04 can guarantee a maximum cycle length that the Dragonball VZ handles by inserting software wait states (see Section 4.2.2, "MC68VZ328 Chip Select and Pin Configuration" on page 13). A single resistor is used to speed up the rise time of the WAIT# (DTACK) signal when terminating the bus cycle. The following diagram shows a typical implementation of the MC68VZ328 to S1D13A04 using the Dragonball host bus interface. For further information on the Dragonball Host Bus interface and AC Timing, refer to the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. MC68VZ328 S1D13A04 A[17:0] D[15:0] CSB1 A18 IO VDD 1K IO VDD AB[17:0] DB[15:0] CS# M/R# BS# RD/WR# WAIT# WE1# WE0# RD# DTACK UWE LWE OE CLK0 System RESET CLKI RESET# Note: When connecting the S1D13A04 RESET# pin, the system designer should be aware of all conditions that may reset the S1D13A04 (e.g. CPU reset can be asserted during wake-up from power-down modes, or during debug states). Figure 4-1: Typical Implementation of MC68VZ328 to S1D13A04 Interface Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-012-01 Page 12 Epson Research and Development Vancouver Design Center 4.2 S1D13A04 Hardware Configuration The S1D13A04 uses CNF6 through CNF0 to allow selection of the bus mode and other configuration data on the rising edge of RESET#. For details on configuration, refer to the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. The following table shows the configuration required for this implementation of a S1D13A04 to Motorola MC68VZ328 microprocessor. Table 4-1: Summary of Power-On/Reset Options S1D13A04 Configuration Input CNF4, CNF[2:0] CNF3 CNF5 CNF6 Power-On/Reset State 1 (connected to IO VDD) Select host bus interface as follows: CNF4 1 CNF2 1 CNF1 1 CNF0 0 Host Bus Dragonball Interface, Big Endian WAIT# is active low CLKI to BCLK divide ratio 1:1 0 (connected to VSS) Reserved. Must be set to 1. WAIT# is active high CLKI to BCLK divide ratio 2:1 configuration for Motorola MC68VZ328 microprocessor S1D13A04 X37A-G-012-01 Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 13 4.2.1 Register/Memory Mapping The S1D13A04 requires two 256K byte segments in memory for the display buffer and its internal registers. To accommodate this block size, it is preferable (but not required) to use one of the chip selects from groups A or B. Groups A and B can have a size range of 128K bytes to 16M bytes and groups C and D have a size range of 32K bytes to 16M bytes. Therefore, any chip select other than CSA0 would be suitable for the S1D13A04 interface. In the example interface, chip select CSB1 controls the S1D13A04. A 512K byte address space is used by setting the SIZ bits of Chip Select Register B (FFFFF116h) to 512k bytes. The S1D13A04 internal registers occupy the first 256K byte block and the 160K byte display buffer is located in the second 256K byte block. A18 from the MC68VZ328 is used to select between these two 256K byte blocks. 4.2.2 MC68VZ328 Chip Select and Pin Configuration The chip select used to map the S1D13A04 (in this example CSB1) must have its RO (Read Only) bit set to 0, its BSW (Bus Data Width) set to 1 for a 16-bit bus, and the WS (Wait states) bits should be set to 111b to allow the S1D13A04 to terminate bus cycles externally with DTACK. The DTACK pin function must be enabled with Register FFFFF433, Port G Select Register, bit 0. If Chip Select Group B is used as the chip select module for the S1D13A04, SRAM timing must be enabled by setting the Chip Select Control Register 1 (FFFFF10Ah) SR16 bit = 0b. Early cycle detection for static memory must be disabled by setting the Chip Select Control Register 2 (FFFFF10Ch) ECDS bit = 0b. If DTACK is not used, then the WS bits should be set to either 4, 6, 10, or 12 software wait states depending on the divide ratio between the S1D13A04 MCLK and BCLK. The WS bits should be set as follows. Table 4-2: WS Bit Programming S1D13A04 MCLK to BCLK Divide Ratio MCLK = BCLK MCLK = BCLK / 2 MCLK = BCLK / 3 MCLK = BCLK / 4 WS Bits (wait states) 4 6 10 12 Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-012-01 Page 14 Epson Research and Development Vancouver Design Center 5 Software Test utilities and display drivers are available for the S1D13A04. Full source code is available for both the test utilities and the drivers. The test utilities are configurable for different panel types using a program called 13A04CFG (see document number X37A-B-001-xx), or by directly modifying the source. The display drivers can be customized by the OEM for different panel types, resolutions and color depths only by modifying the source. The S1D13A04 test utilities and display drivers are available from your sales support contact (see Section 7, "Sales and Technical Support") or at www.erd.epson.com. S1D13A04 X37A-G-012-01 Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 15 6 References 6.1 Documents * Motorola Inc., MC68VZ328 DragonBall-VZ(R) Integrated Processor User's Manual, Motorola Publication no. MC683VZ28UM; available on the Internet at http://www.mot.com/SPS/WIRELESS/products/MC68VZ328.html. * Epson Research and Development, Inc., S1D13A04 Hardware Functional Specification, Document Number X37A-A-001-xx. * Epson Research and Development, Inc., S5U13A04B00C Rev. 1.0 Evaluation Board User Manual, Document Number X37A-G-004-xx. * Epson Research and Development, Inc., S1D13A04 Programming Notes and Examples, Document Number X37A-G-003-xx. 6.2 Document Sources * Motorola Inc. Literature Distribution Center: (800) 441-2447. * Motorola Inc. Website: www.mot.com. * Epson Research and Development Website: www.erd.epson.com. Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-012-01 Page 16 Epson Research and Development Vancouver Design Center 7 Sales and Technical Support 7.1 EPSON LCD/USB Companion Chips (S1D13A04) Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk/ Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de 7.2 Motorola MC68VZ328 Processor * Motorola Design Line, (800) 521-6274. * Local Motorola sales office or authorized distributor. S1D13A04 X37A-G-012-01 Interfacing to the Motorola MC68VZ328 Dragonball Microprocessor Issue Date: 01/10/12 S1D13A04 LCD/USB Companion Chip Interfacing to the Intel StrongARM SA-1110 Microprocessor Document Number: X37A-G-013-01 Copyright (c) 2001 Epson Research and Development, Inc. All Rights Reserved. Information in this document is subject to change without notice. You may download and use this document, but only for your own use in evaluating Seiko Epson/EPSON products. You may not modify the document. Epson Research and Development, Inc. disclaims any representation that the contents of this document are accurate or current. The Programs/Technologies described in this document may contain material protected under U.S. and/or International Patent laws. EPSON is a registered trademark of Seiko Epson Corporation. All Trademarks are the property of their respective owners. Page 2 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-013-01 Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 3 Table of Contents 1 2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Interfacing to the StrongARM SA-1110 Bus 2.1 The StrongARM SA-1110 System Bus . . 2.1.1 StrongARM SA-1110 Overview . . . 2.1.2 Variable-Latency IO Access Overview 2.1.3 Variable-Latency IO Access Cycles . ... ... .... .... .... ... .. ... ... ... . . . . . ...... ..... ....... ....... ....... . . . . . ....... ...... ........ ........ ........ .8 .8 .8 .8 .9 3 S1D13A04 Host Bus Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3.1 Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . 11 3.2 Host Bus Interface Signal Descriptions . . . . . . . . . . . . . . . . . . . . 12 StrongARM SA-1110 to S1D13A04 Interface 4.1 Hardware Description . . . . . . . . . 4.2 S1D13A04 Hardware Configuration . . . 4.3 StrongARM SA-1110 Register Configuration 4.4 Register/Memory Mapping . . . . . . . . . . . . . . . . . . . . . . ... .. .. .. .. . . . . . . . . . . . . . . . ... .. .. .. .. . . . . . . . . . . . . . . . ... .. .. .. .. . . . . . . . . . . . . . . . 13 13 14 15 16 4 5 6 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.1 Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 6.2 Document Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Sales and Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7.1 EPSON LCD/USB Companion Chips (S1D13A04) . . . . . . . . . . . . . . . 19 7.2 Intel StrongARM SA-1110 Processor . . . . . . . . . . . . . . . . . . . . . 19 7 Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-013-01 Page 4 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-013-01 Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 5 List of Tables Table 3-1: Host Bus Interface Pin Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Table 4-1: Summary of Power-On/Reset Options . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Table 4-2: RDFx Parameter Value versus CPU Maximum Frequency . . . . . . . . . . . . . . . . 15 List of Figures Figure 2-1: SA-1110 Variable-Latency IO Read Cycle . . . . . . . . . . . . . . . . . . . . . . . . 9 Figure 2-2: SA-1110 Variable-Latency IO Write Cycle . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 4-1: Typical Implementation of SA-1110 to S1D13A04 Interface . . . . . . . . . . . . . . . 13 Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-013-01 Page 6 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-013-01 Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 7 1 Introduction This application note describes the hardware and software environment required to provide an interface between the S1D13A04 LCD/USB Companion Chip and the Intel StrongARM SA-1110 Microprocessor. The designs described in this document are presented only as examples of how such interfaces might be implemented. This application note is updated as appropriate. Please check the Epson Research and Development website at www.erd.epson.com for the latest revision of this document before beginning any development. We appreciate your comments on our documentation. Please contact us via email at documentation@erd.epson.com. Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-013-01 Page 8 Epson Research and Development Vancouver Design Center 2 Interfacing to the StrongARM SA-1110 Bus 2.1 The StrongARM SA-1110 System Bus The StrongARM SA-1110 microprocessor is a highly integrated communications microprocessor that incorporates a 32-bit StrongARM RISC processor core. The SA-1110 is ideally suited to interface to the S1D13A04 LCD controller and provides a high performance, power efficient solution for embedded systems. 2.1.1 StrongARM SA-1110 Overview The SA-1110 system bus can access both variable-latency IO and memory devices. The SA-1110 uses a 26-bit address bus and a 32-bit data bus which can be used to access 16-bit devices. A chip select module with six chip select signals (each accessing 64M bytes of memory) allows selection of external devices. Only chip selects 3 through 5 (nCS[5:3]) may be used to select variable-latency devices which use RDY to extend access cycles. These chip selects are individually programmed in the SA-1110 memory configuration registers and can be configured for either a 16 or 32-bit data bus. Byte steering is implemented using the four signals nCAS[3:0]. Each signal selects a byte on the 32-bit data bus. For example, nCAS0 selects bits D[7:0] and nCAS3 selects bits D[31:24]. For a 16-bit data bus, only nCAS[1:0] are used with nCAS0 selecting the low byte and nCAS1 selecting the high byte. The SA-1110 can be configured to support little or big endian mode. 2.1.2 Variable-Latency IO Access Overview A data transfer is initiated when a memory address is placed on the SA-1110 system bus and a chip select signal (nCS[5:3]) is driven low. If all byte enable signals (nCAS[3:0]) are driven low, then a 32-bit transfer takes place. If only nCAS[1:0] are driven low, then a word transfer takes place through a 16-bit bus interface. If only one byte enable is driven low, then a byte transfer takes place on the respective data lines. During a read cycle, the output enable signal (nOE) is driven low. A write cycle is specified by driving nOE high and driving the write enable signal (nWE) low. The cycle can be lengthened by driving RDY high for the time needed to complete the cycle. S1D13A04 X37A-G-013-01 Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 9 2.1.3 Variable-Latency IO Access Cycles The first nOE assertion occurs two memory cycles after the assertion of chip select (nCS3, nCS4, or nCS5). Two memory cycles prior to the end of minimum nOE or nWE assertion (RDF+1 memory cycles), the SA-1110 starts sampling the data ready input (RDY). Samples are taken every half memory cycle until three consecutive samples (at the rising edge, falling edge, and following rising edge of the memory clock) indicate that the IO device is ready for data transfer. Read data is latched one-half memory cycle after the third successful sample (on falling edge). Then nOE or nWE is deasserted on the next rising edge and the address may change on the subsequent falling edge. Prior to a subsequent data cycle, nOE or nWE remains deasserted for RDN+1 memory cycles. The chip select and byte selects (nCAS[1:0] for 16-bit data transfers), remain asserted for one memory cycle after the final nOE or nWE deassertion of the burst. The SA-1110 is capable of burst cycles during which the chip select remains low while the read or write command is asserted, precharged and reasserted repeatedly. Figure 2-1: illustrates a typical variable-latency IO access read cycle on the SA-1110 bus. A[25:0] ADDRESS VALID nCS4 nOE nWE RDY D[31:0] DATA VALID nCAS[3:0] Figure 2-1: SA-1110 Variable-Latency IO Read Cycle Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-013-01 Page 10 Epson Research and Development Vancouver Design Center Figure 2-2: illustrates a typical variable-latency IO access write cycle on the SA-1110 bus. A[25:0] ADDRESS VALID nCS4 nWE nOE RDY D[31:0] DATA VALID nCAS[3:0] Figure 2-2: SA-1110 Variable-Latency IO Write Cycle S1D13A04 X37A-G-013-01 Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 11 3 S1D13A04 Host Bus Interface The S1D13A04 directly supports multiple processors. The S1D13A04 implements a 16-bit Generic #2 Host Bus Interface which is most suitable for direct connection to the SA-1110. The Generic #2 Host Bus Interface is selected by the S1D13A04 on the rising edge of RESET#. After releasing reset the bus interface signals assume their selected configuration. For details on S1D13A04 configuration, see Section 4.2, "S1D13A04 Hardware Configuration" on page 14. 3.1 Host Bus Interface Pin Mapping The following table shows the functions of each Host Bus Interface signal. Table 3-1: Host Bus Interface Pin Mapping S1D13A04 Pin Name AB[17:0] DB[15:0] WE1# M/R# CS# CLKI BS# RD/WR# RD# WE0# WAIT# RESET# SA-1110 A[17:0] D[15:0] nCAS1 A18 nCS4 SDCLK2 Connect to IOVDD from the S1D13A04 Connect to IOVDD from the S1D13A04 nOE nWE RDY system RESET Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-013-01 Page 12 Epson Research and Development Vancouver Design Center 3.2 Host Bus Interface Signal Descriptions The S1D13A04 Generic #2 Host Bus Interface requires the following signals. * CLKI is a clock input which is required by the S1D13A04 Host Bus Interface as a source for its internal bus and memory clocks. This clock is typically driven by the host CPU system clock. For this example, it is driven by one of the SA-1110 signals SDCLK1 or SDCLK2 (The example implementation in this document uses SDCLK2). For further information, see Section 4.3, "StrongARM SA-1110 Register Configuration" on page 15. * The address inputs AB[17:0], and the data bus DB[15:0], connect directly to the SA1110 address bus (A[17:0]) and data bus (D[15:0]), respectively. CNF4 must be set to select little endian mode. * M/R# (memory/register) selects between memory or register accesses. This signal is generated by the external address decode circuitry. For this example, M/R# is connected to address line A18, allowing system address A18 to select between memory or register accesses. * Chip Select (CS#) must be driven low by nCSx (where x is the SA-1110 chip select used) whenever the S1D13A04 is accessed by the SA-1110. * WE1# connects to nCAS1 (the high byte enable signal from the SA-1110) which in conjunction with address bit 0 allows byte steering of read and write operations. * WE0# connects to nWE (the write enable signal from the SA-1110) and must be driven low when the SA-1110 is writing data to the S1D13A04. * RD# connects to nOE (the read enable signal from the SA-1110) and must be driven low when the SA-1110 is reading data from the S1D13A04. * WAIT# connects to RDY and is a signal output from the S1D13A04 that indicates the SA-1110 must wait until data is ready (read cycle) or accepted (write cycle) on the host bus. Since SA-1110 accesses to the S1D13A04 may occur asynchronously to the display update, it is possible that contention may occur in accessing the S1D13A04 internal registers and/or display buffer. The WAIT# line resolves these contentions by forcing the host to wait until the resource arbitration is complete. * The Bus Start (BS#) and RD/WR# signals are not used for this Host Bus Interface and should be tied high (connected to IOVDD). * The RESET# (active low) input of the S1D13A04 may be connected to the system RESET. S1D13A04 X37A-G-013-01 Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 13 4 StrongARM SA-1110 to S1D13A04 Interface 4.1 Hardware Description The SA-1110 microprocessor provides a variable latency I/O interface that can be used to support an external LCD controller. By using the Generic # 2 Host Bus Interface, no glue logic is required to interface the S1D13A04 and the SA-1110. A pull-up resistor is attached to WAIT# to speed up its rise time when terminating a cycle. BS# (bus start) and RD/WR# are not used by the Generic #2 Host Bus Interface and should be tied high (connected to IO VDD). The following diagram shows a typical implementation of the SA-1110 to S1D13A04 interface. SA-1110 nWE nCAS1 S1D13A04 WE0# WE1# RD# nOE nCS4 RDY A18 Pull-up CS# WAIT# M/R# System RESET RESET# AB[17:0] DB[15:0] CLKI A[17:0] D[15:0] SDCLK2 IO VDD BS# RD/WR# Note: When connecting the S1D13A04 RESET# pin, the system designer should be aware of all conditions that may reset the S1D13A04 (e.g. CPU reset can be asserted during wake-up from power-down modes, or during debug states). Figure 4-1: Typical Implementation of SA-1110 to S1D13A04 Interface Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-013-01 Page 14 Epson Research and Development Vancouver Design Center 4.2 S1D13A04 Hardware Configuration The S1D13A04 uses CNF6 through CNF0 to allow selection of the bus mode and other configuration data on the rising edge of RESET#. For details on configuration, refer to the S1D13A04 Hardware Functional Specification, document number X37A-A-001-xx. The following table shows the configuration required for this implementation of a S1D13A04 to SA-1110 interface. Table 4-1: Summary of Power-On/Reset Options S1D13A04 Configuration Input CNF4, CNF[2:0] CNF3 CNF5 CNF6 Power-On/Reset State 1 (connected to IO VDD) Select host bus interface as follows: CNF4 0 CNF2 1 CNF1 0 CNF0 0 Host Bus Generic #2, Little Endian WAIT# is active low CLKI to BCLK divide ratio 1:1 0 (connected to VSS) Reserved. Must be set to 1. WAIT# is active high CLKI to BCLK divide ratio 2:1 configuration for SA-1110 microprocessor S1D13A04 X37A-G-013-01 Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 15 4.3 StrongARM SA-1110 Register Configuration The SA-1110 requires configuration of several of its internal registers to interface to the S1D13A04 Generic #2 Host Bus Interface. * The Static Memory Control Registers (MSC[2:0]) are read/write registers containing control bits for configuring static memory or variable-latency IO devices. These registers correspond to chip select pairs nCS[5:4], nCS[3:2], and nCS[1:0] respectively. Each of the three registers contains two identical CNFG fields, one for each chip select within the pair. Since only nCS[5:3] controls variable-latency IO devices, MSC2 and MSC1 should be programmed based on the chip select used. Parameter RTx<1:0> should be set to 01b (selects variable-latency IO mode). Parameter RBWx should be set to 1 (selects 16-bit bus width). Parameter RDFx<4:0> should be set according to the maximum desired CPU frequency as indicated in the table below. Table 4-2: RDFx Parameter Value versus CPU Maximum Frequency CPU Frequency (MHz) 57.3 - 85.9 88.5 - 143.2 147.5 - 200.5 206.4 - 221.2 RDFx 1 2 3 4 Parameter RDNx<4:0> should be set to 0 (minimum command precharge time). Parameter RRRx<2:0> should be set to 0 (minimum nCSx precharge time). * The S1D13A04 endian mode is set to little endian. To program the SA-1110 for little endian set bit 7 of the control register (register 1) to 0. * The CLKI signal input to the S1D13A04 from one of the SDCLK[2:1] pins is a derivative of the SA-1110 internal processor speed (either divide by 2 or 4). The S1D13A04 Generic #2 Host Bus Interface has a maximum BCLK of 50MHz. Therefore, if the processor clock is higher than 100MHz, either divide the BCLK input using the S1D13A04 configuration pin CNF6 (see Table 4-1: "Summary of Power-On/Reset Options" ) or set SDCLK1/SDCLK2 to CPU clock divided by four using the DRAM Refresh Control Register (MDREFR bit 26 = 1 for SDCLK2, MDREFR bit 22 = 1 for SDCLK1). Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-013-01 Page 16 Epson Research and Development Vancouver Design Center 4.4 Register/Memory Mapping The S1D13A04 is a memory-mapped device. The SA-1110 uses the memory assigned to a chip select (nCS4 in this example) to map the S1D13A04 internal registers and display buffer. The S1D13A04 uses two 256K byte blocks which are selected using A18 from the SA-1110 (A18 is connected to the S1D13A04 M/R# pin).The internal registers occupy the first 256K bytes block and the 160K byte display buffer occupies the second 256K byte block. Each variable-latency IO chip select is assigned 128M Bytes of address space. Therefore; if nCS4 is used the S1D13A04 registers will be located at 4000 0000h and the display buffer will be located at 4004 0000h. These blocks are aliased over the entire 128M byte address space. Note If aliasing is not desirable, the upper addresses must be fully decoded. S1D13A04 X37A-G-013-01 Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 17 5 Software Test utilities and display drivers are available for the S1D13A04. Full source code is available for both the test utilities and the drivers. The test utilities are configurable for different panel types using a program called 13A04CFG (see document number X37A-B-001-xx), or by directly modifying the source. The display drivers can be customized by the OEM for different panel types, resolutions and color depths only by modifying the source. The S1D13A04 test utilities and display drivers are available from your sales support contact (see Section 7, "Sales and Technical Support") or www.erd.epson.com. Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-013-01 Page 18 Epson Research and Development Vancouver Design Center 6 References 6.1 Documents * Intel Corporation, StrongARM(R) SA-1110 Microprocessor Advanced Developer's Manual, Order Number 278240-001. * Epson Research and Development, Inc., S1D13A04 Hardware Functional Specification, Document Number X37A-A-001-xx. * Epson Research and Development, Inc., S1D13A04 Programming Notes and Examples, Document Number X37A-G-003-xx. * Epson Research and Development, Inc., S5U13A04B00C Rev. 1.0 ISA Bus Evaluation Board User Manual, Document Number X37A-G-004-xx. 6.2 Document Sources * Intel Developers Website: http://developer.intel.com. * Intel Literature contact: 1(800) 548-4725. * Epson Research and Development Website: www.erd.epson.com. S1D13A04 X37A-G-013-01 Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 Epson Research and Development Vancouver Design Center Page 19 7 Sales and Technical Support 7.1 EPSON LCD/USB Companion Chips (S1D13A04) Japan Seiko Epson Corporation Electronic Devices Marketing Division 421-8, Hino, Hino-shi Tokyo 191-8501, Japan Tel: 042-587-5812 Fax: 042-587-5564 http://www.epson.co.jp North America Epson Electronics America, Inc. 150 River Oaks Parkway San Jose, CA 95134, USA Tel: (408) 922-0200 Fax: (408) 922-0238 http://www.eea.epson.com Taiwan Epson Taiwan Technology & Trading Ltd. 10F, No. 287 Nanking East Road Sec. 3, Taipei, Taiwan Tel: 02-2717-7360 Fax: 02-2712-9164 http://www.epson.com.tw/ Singapore Epson Singapore Pte., Ltd. No. 1 Temasek Avenue #36-00 Millenia Tower Singapore, 039192 Tel: 337-7911 Fax: 334-2716 http://www.epson.com.sg/ Hong Kong Epson Hong Kong Ltd. 20/F., Harbour Centre 25 Harbour Road Wanchai, Hong Kong Tel: 2585-4600 Fax: 2827-4346 http://www.epson.com.hk/ Europe Epson Europe Electronics GmbH Riesstrasse 15 80992 Munich, Germany Tel: 089-14005-0 Fax: 089-14005-110 http://www.epson-electronics.de 7.2 Intel StrongARM SA-1110 Processor INTEL Intel Customer Support (ICS) for StrongARM: (800) 628-8686 Website for StrongARM Processor http://developer.intel.com/design/strong/ Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 S1D13A04 X37A-G-013-01 Page 20 Epson Research and Development Vancouver Design Center THIS PAGE LEFT BLANK S1D13A04 X37A-G-013-01 Interfacing to the Intel StrongARM SA-1110 Microprocessor Issue Date: 01/10/12 |
Price & Availability of S1D13A04
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |